Search Documents

OWING to the gradual depletion of the hitherto plentiful supply of firewood in the immediate vieinity of Queenstown and Gormanston, which caused a steady increase in the cost of fuel for domestic purposes, the Mount Lyell Company took steps several years ago to make available as a substitute electric current from its Lake Margaret hydro-electric supply. In order to make this practicable it was necessary that the cost of electric power for heating purposes should compare favourably with the cost, of fuel, and the installation of domestic appliances brought within reach of the average householder, and efforts have been continuously directed towards this end since the year 1928.WATER HEATERSThe installation of electrical apparatus in local dwellings began with hot-water services, the heating elements being the types then procurable on the market and adapted to meet requirements.These, however, did not prove satisfactory, but the study of their bilure resulted in a type being developed locally which has overcome all difficulties. The first type of water heater evolved was an outside circulation one the element of which consisted of an iron pipe through which the water passed, insulated with micanite and wound with nichrome wire, the latter being covered with alundun cement to keep it in position and prevent oxidation. This was insulated on its outside surface with a layer of asbestos flour, and connected to the hot-water container as shown in Fig. 1. It was found, however, that the iron pipe had a short life, due to a certain amount of acidity in the water, and a copper pipe was substituted which proved very durable. Some heaters with this improved type of element are still operating after six years of use. The resistance wire is run at a very low current density, which ensures durability.

Jan 1, 1927

By B. C. Blake

IN general, billet-type or long slender ingots are used when it is desired to produce directly from the ingot in one conversion a product of medium or small cross-sectional area. They are designed to eliminate the blooming and billet-mill stages of the usual procedure. As used at Connors, they constitute a means of keeping a continuous rolling mill busy in the production of high-quality small rods, small angles, hoop stock, baling ties and concrete reinforcing rods without the need for a blooming or billet mill. They represent sound steel with the best surface that is commercially practical to use in the rolling of small continuous mill products.

Jan 1, 1947

By Tim O’Neil

Caterpillar has introduced its 5090B front shovel, to work with 40 to 70 st (36 to 63 t) trucks. The new unit replaces Cat’s 5080 hydraulic excavator. The 5090B offers more engine horsepower, higher flow, greater digging forces, higher swing torque, faster swing speed and more drawbar pull than its predecessor. It can also handle larger bucket sizes than the previous model. These improvements enhance productivity and make the 5090B a high-volume material handler for hard rock and aggregates producers.

Jan 1, 2003

By James M. Franklin

Research on modern hydrothermal systems provides quantitative measures of the processes of formation of hydrothermal fluids and of precipitation mechanisms from them. Studies of ancient deposits provide new information regarding volcanological processes that are related to the deposits, as well as data on their spatial and temporal compositional variations. Mew exploration guidelines result from both aspects of research. The most fundamental requirement for large metalliferous hydrothermal systems is an abundant heat supply for the upper two kilometers of the crust. This heat may come from a focused heal source (shallow-level subvolcanic intrusion), but ambient heat also may have provided enough energy for the reactions necessary to effect leaching of metals, especially where heat flow is particularly high (i.e. very large or high-temperature magmatic source, such as ultramafic environments). For most VMS systems, the majority of the metals were derived through leaching from footwall strata; in addition interstratal fluids may enter subvolcanic intrusions during episodes of magma a chamber "cracking," engendering some '?magmatic" component in the hydrothermal system. Direct contributions of metalliferous magmatic fluid also may be significant from arc-related or back-arc felsic or alkalis systems. These latter contributions may form exceptionally high - grade portions in some deposits. Subvolcanic intrusions, which are excellent indicators of high heat flow and may have been the direct driving mechanisms for some stems undergo two stages of alteration: On intrusion emplacernent. fluids may rapidly enter and react with their mesostatic portions, evident in the sills in the Middle Valley. High temperature interactions caused albitization and destruction of oxides and sulfides, releasing metals. During terminal hydrothermal stages, the metalliferous fluid collapsed into the intrusions, forming disseminated and vein sulfides.

Jan 1, 1998

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W. FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS -T. READ, Secretary, Woolworth Bldg., New York: N. Y. P. A. MOSMAN, Treasurer. LOUIS D: HUNTOON. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 10, 1914

OFS Branch Proceedings of the Annual General Meeting ofthe O.F.S. Branch on Wednesday, 31st July, 1974. The Annual General Meeting of the Branch was held at the Western Holdings Limited Canteen on Wednesday, 31st July, 1974 at 7.30 p.m. Mr E. T. Wilson (Chairman) was in the Chair. There were also present: Papers of interest The following papers may be of interest to members. Education fund The Institute has recently brought into being a Fund to finance various educational projects.

Jan 5, 1974

By J. F. Lewis

Believing that one of the essential points in mining, as in all other business, is to know the expense incurred in each particular department, I have carefully kept an account with each department for the past three years; and, as it may be of interest to some of our members, I herewith present it to the Institute, reduced to per centages of the total yearly expense, showing the cost for materials, repairs, expenses, tools, team accounts, powder, oil, and fuel, also for labor under its several heads: 1875—Materials. 1875—Labor, Repairs,...040 Expenses,....016 Team,. .. .. .017 Machinery,. .. .055 Tools,..006 Repairs,. .. .027 Improvements,.....030 Washer,. .. .076 Oil ..008 Pit,.. 178 Powder,..,043 Dirt,.. 130 Fuel,. .325 Superintendence,. ..050 .485 .516 100.1 1876—-Materials. 1876-Labor. Repairs,. . • .. .043 Expenses,......012 Team,.011 Machinery,. .. .090 Tools,..005 Repairs,... 027 Improvements,.....007 Washer,. .. .085 I,. ...,015 Pit,.. 139 Powder,. .. .. .030 Dirt,.. 160 Fuel,...321 Superintendence,. ..078 .444 .559 100.3 1877—Materials. 1877—Labor. Repairs,......102 Expenses,......019 Team,..031 Machinery,. .. .050 Tools,..030 Rrpairs,. .. .046 Improvements,....,031 Washer,. .. .057 I,...009 Pit,.....179 Powder,...035 Dirt,.. 162 Fuel,...200 Superintendence,. ..054 .457 .548 100.5 Average for the three years 1875, '76, and '77. Materials. Labor. Repairs,...062 Expenses,...016 Team,..016 Machinery,. .. .065

Jan 1, 1879

By W. J. Atkinson

The first recorded discovery of diamonds in Australia was in 1851 in New South Wales. Subsequent prospecting has shown alluvial occurrences of diamond to be widespread through much of the Tasman fold belts of Eastern Australia. Production is estimated to be some 500,000 carats from several small alluvial fields. Despite extensive exploration, though, no primary rock source carrying significant diamond content has ever been confirmed in Eastern Australia. Conversely, diamond exploration of the older Western and Central Cratons of Australia during the past 30 years has discovered 12 fields containing 360 kimberlites, lamproites and lamprophyric volcanic pipes, dykes and other intrusives. Of those, 180 have been confirmed to be diamondiferous. Only one pipe, however, the 1200 Ma high-grade Argyle lamproite and associated nearby alluvials, has proved to be economically exploitable. Its current annual production is 40 million carats valued at about US$400 million. Production from the open pit will be sustainable until at least 2003.

Jan 1, 1995

By Pollyana de Aragão Trigueiro

A distribuição de soluto durante a solidificação rápida de uma liga Ag-15%massaCu, foi obtida numericamente. No presente trabalho, utilizamos um modelo de difusão de entalpia e concentração médias, proposto anteriormente, para a solidificação de uma gota de liga binária (atomização). Nossos resultados mostram que a refusão da estrutura pode gerar um perfil de microssegregação em ligas solidificadas rapidamente bastante diferente dos que resultam da solidificação perto do equilíbrio.

Aug 7, 2018

The Golden Ridges Mine, one of the properties of New Guinea Goldfields Limited, is situated on the right bank of Nami Creek, not far from the township of Wau, in the Territory of New Guinea.The property is somewhat unique, in that the goldbearing ore-body occurs in the form of a flat seam-like deposit lying on a volcanic breccia, and covered with a mantle of overburden of decomposed porphyry. The overburden varies in thickness up to a maximum of about 65 ft.The ratio of overburden to ore is about 3 to 1. The practice developed is to strip the overburden by hydraulicking, and to mine the exposed ore under open-cut conditions, blasting to a vertical face, and using electrically operated scraper hoists for conveying the broken ore to the mill bins.The stripping of the overburden involves the boring of well-drill holes, blasting the holes and then hydraulicking the shattered material.

Jan 1, 1934

The theme of the conference is "excellence", an epithet of special significance in tertiary education. It appears in the mission statements, goals and plans to achieve them of most, and quite possibly all, tertiary institutions in Australia. In the context of excellence, this paper examines the current statue of professional education in the principal mining industry related discipline of Mining Engineering. It furthermore, identifies and discusses a number of special problems in mining education that the tertiary sector has long endured. Some of these problems are becoming acute, and solutions will have to be found soon in order for the industry to be assured of the supply of well motivated and appropriately qualified young engineers and scientists necessary to achieve and maintain the excellent to which it aspires.

Jan 1, 1989

The recovery by flotation of some complex uranium minerals such as brannerite and davidite is described. Anionic reagents used for flotation of iron and titanium oxides' are suitable. If care is taken, to emulsify the reagents the slime fractions may be satisfactorilytreated.INTRODUCTIONUranium ores are usually treated by direct leaching with acid or alkali according to the nature of the gangue materials. Concentration of the uranium minerals prior to leaching is not commonly practised because of the earthy nature of most uranium minerals and the difficult mineral dressing problem they pose. Some of the harder complex oxides such as davidite and brannerite are amenable to flotation. This is fortunate since they usually require an expensive, strong acid treat~ent to dissolve the uranium. Flotation tests were commenced in 1949 by officers of the South Australian Department of Mines stationed at Adelaide, first in the School of Mines, then in the University of Adelaide and finally in Departmental mineral dressing laboratories at Thebarton. Separation of daviditefrom Radium Hill and Mount Victoria ores, brannerite from Crocker's Well ore, and secondary uranium minerals from Myponga ore was attempted.The development of the flotation reagents to separate the oxides from silica and the silicates is first described, then some of the results obtained are presented as tables.DEVELOPMENT OF FLOTATION REAGENTSThe davidite at Radium Hill is associated with iron and titanium oxides, qu;a,rtz and biotite as replacement deposits in shears. The davidite, rutile,' ilmenite and hematite usually occur in segregations from nut size to masses of several pounds. They are associated as a complexity of...

Jan 1, 1955

By J. Björkvall, L. Bååth, D. Malmberg, J. Malm

Microwave technology has for decades been a tool for astronomers to map and understand the complexities of the universe its composition and extent. It is also used on a laboratory scale by spectroscopists to examine properties of atomic and molecular compounds. In this novel work we will introduce microwave technology to be used for the investigation of liquid slag structures. The preliminary results indicate that the alteration of the slag composition could be correlated to the measured microwave refractive index. Investigations have been performed in the Al2O3-CaO-SiO2slag system. Keywords: Microwave technology, slag, structure, liquid, Al2O3-CaO-SiO2

Jan 1, 2004

The consideration of environmental constraints and issues is a fundamental component of all stages of planning, development, operation and decommissioning mining and quarrying projects. Provision needs to be made at all stages for the cost of environmental components since it is of fundamental importance that they be recognised as an integral component of any project. This paper presents an approach to environmental costing, suggested levels for budgeting, and the cost benefits.

Jan 1, 1990

By H. D. Jacobs

The Federal Bureau of Mines, as part of a program to insure future raw material needs for the iron and steel industry, undertook research to beneficiate the oxidized taconites from the western Mesabi range in Minnesota. The data presented were obtained by applying the Bureau-developed selective-flocculation/cationic-flotation process to the second of three oxidized taconite samples. These three samples are representative of an estimated 10 billion tons of ore analyzing 30 to 40 pct iron. The experimental work was performed in a 900-lb/hr pilot plant. Treating the ore sample (36.1 pct Fe) with the Bureau's process produced commercially acceptable concentrates averaging 63.5 pct Fe and 4.3 pct SiO2, with an average iron recovery of 84.6 pct.

Jan 1, 1980

By Esperanza Tauler, Lluis Rivero, Victoria Cutipa, Raúl y. Lovera, Elisabet Playá

En España, el yeso es una de las litologías sedimentarias más abundantes en afloramientos. Se concentra especialmente en terrenos del Triásico, Paleógeno y Mioceno, explotándose los depósitos del Mioceno en las tres grandes cuencas Terciarias de la Península Ibérica (Cuencas del Ebro, Duero y Tajo). Para conocer la continuidad de los niveles de yeso se utiliza una reciente técnica geofísica no destructiva denominada Tomografía Eléctrica, que permite obtener una distribución de las resistividades reales del subsuelo, inyectando una corriente continua a través de electrodos, logrando delimitar los niveles de una manera práctica y facilitando su modelamiento.

By Bin Tang, Suping Yao

In the last decade, the copper industry in China has developed rapidly and attracted the world’s attention. The production capacity of refined copper has grown remarkably from 4.578 million tons in 2010 up to 9.029 million tons in 2018, accounting for about 40% of the global refined copper production. And now, China has become the biggest refined copper producer in the world. This paper summarizes the application of modern copper metallurgical technologies such as Outotec flash smelting/converting technology, Cyclone smelting technology, TSL (ISA/Ausmelt) smelting/converting technology, Jinfeng side blown smelting and Baiyin side blown smelting technology, Chifeng side blown smelting and continuous top blown converting technology, SKS bottom blowing technology, Dongying two-step smelting technology, copper electrorefining with high current density, etc. in China’s copper industry, analyzes and compares the characteristics of those technologies and presents the great efforts of China’s copper smelters in adapting to the increasingly strict emission standards and improving economic benefits of copper smelters. INTRODUCTION China has been the biggest refined copper producer in the world for many years. China produced million tons of refined copper in 2018, accounting for 40% of the copper smelting production in the world, and of which, roughly, 70% of the copper concentrate was imported, mainly from Chile, Peru and Australia. ICSG (International Copper Study Group, 2017) shows clearly the position of top 20 countries of copper production and copper mine production (Figures 1 and 2). Blast Furnaces, Reverb Furnaces and Electric Furnaces dominated China Copper Smelting for quite long time till 1980s. The first modern copper smelting technology (flash copper smelting) was introduced into China in 1980s, then followed by Noranda, Ausmelt and ISA. Since then, China copper smelting technology stepped into modern time. Since 2000, old processes (Blast Furnace, Reverb Furnaces and Electric Furnaces) were phased out and replaced by modern smelting technologies. China Copper Production has been increasing dramatically (Figure 3).

Jan 1, 2019

By George A. Morgan

There was little change in the mineral industry of Benin in 1986, as the economy remained in the grip of a regional recession exacerbated by failing oil prices, which nullified much of the income from Benin's oil production. Benin's industrial sector accounted for less than 10% of the gross domestic product (GDP), with the mineral industry providing about one-half of that total. Several major projects initiated over the last several years continued to perform and/or progress below Government expectations. These included the Save sugar refinery, the Dassa-Parakou section of the Dassa-Cotonou highway, the Benin-Togo Nangbeto hydroelectric plant, the Onigbolo cement plant, and the Semé Oilfield. Funding for these projects is the major source of the Beninese external debt, which was estimated to be over $800 million.2

Jan 1, 1988

By McKenzie P

The techniques of geological control developed by the Coal Geology Sections of the Broken Hill Proprietary Company Limited and Australian Iron and Steel Proprietary Limited in providing geological service in the coilieries operated by these associated companies cover the provision of geological control for both planning and production in each of which the significance of geology has in the past been only poorly appreciated by the coal mining industry.While the adoption of similar techniques is well within the capacity of major companies there is considerable scope for the development of government geological services providing specialized assistance of this nature for smaller scale producers.INTRODUCTIONThe coal mining industry in Australia can instance many notable mistakes caused by failure to obtain sufficient geological information or by incorrect interpretation of available geological evidence both before the commencement of mining and during the progress of operations. Substantial development undertaken in, areas with insufficient or inferior coal reserves, difficult mining conditions caused by failure to adjust operations to geological circumstances, and the irregular development of mine workings caused by unexpected geological features, all bear witness to the lack of geological foresight by the industry.Along with the more widespread general use of applied geology, an increasing acceptance has developed during the past ten years of the valuable contribution which can be made by this science to the exploitation of coalfields. In spite of the advances which have been made, there is still a wide scope for further detailed application of geology throughout the coal mining industry in Australia.

Jan 1, 1963

By E. Hornbogen

The deformation mechanisms of a iron-phosphorus alloys were compared at 20oand —196°C. Alloying with phosphorus increases the resistance to slip, but has little effect on the resistance to twinning. The stress for onset of twinning is nearly independent of temperature, but there is an increasing tendency for cleavage along (112) twin boundaries with decreasing temperature and increasing phosphorus content. FIVE iron-phosphorus alloys and one high-purity iron (0.004 pct C, 0.004 pct N, 0.05 pct O) were vacuum melted and cast, then homogenized for 6 hr at 1100oC and water-quenched. Single crystals were cleaved from the coarse grains produced in this manner. The hardness was measured* on polished (100) surfaces of the crystals at 20" and -196°C. Laue back-reflection patterns indicated a deviation of not more than 3 deg from coincidence of the {100} plane with the surface. The deformation mechanisms were studied by relief effects on the polished surfaces. Yield points in compression (0.5 pct offset) were measured with polycrystalline material. At 20°C the addition of phosphorus to a iron leads to a change from slip to twinning as the main deformation mechanism, Figs. 1(a), (b). Between 2 and 4 at. pct P slip and twinning occur simultaneously. In alloys with more than 4 at. pct P twinning is the main deformation mechanism and slip was observed only in the neighborhood of twin intersections. All cracks at 20oC were on (100) planes, some initiated by twins.' From measurements made at-196oC, hardness and yield points of all the alloys were nearly constant and the same as the hardness of high phosphorus alloys that deformed by twinning at 20°C, Figs. 2 and 3. In the high-purity iron, plastic deformation at -196°C occurred by both slip and twinning, but deformation in the iron-phosphorus alloys appeared to be entirely by twinning. In the high phosphorus alloys a large number of cracks formed along the (112) twin boundaries and at intersections of twins, in addition to the (100) cleavage, Fig. 1(c). DISCUSSION In , iron, plastic deformation can occur either by slip or by twinning, depending upon composition,

Jan 1, 1961