Search Documents

By R. B. Sosman, J. C. Hostetter

It is well known that ferric oxide, Fe2O3, is paramagnetic, while magnetite, Fe3o4, is classed among the highly ferromagnetic substances. But magnetic data on oxides intermediate in composition between Fe2o3 and Fe3O4 have been almost completely lacking. Fe2O3 and Fe3O4 form a solid-solution series, according to present evidence.' In this series the properties change continuously from Fe2O3 toward Fe3O4, as the percentage of FeO increases from zero toward 31.03, which is the percentage in magnetite. It is possible that there is a break in the series near Fe3O4, but it has not yet been possible to establish the existence of such a break experimentally. The occurrence of solid solution in this series is shown by the dissociation pressure, or oxygen pressure in equilibrium with the oxides, which falls continuously over the range from Fe2O3 to Fe3O4. The oxygen-pressure curves at 1100" and 1200" are shown in Fig. 1. The existence of solid solution is also demonstrated by the continuous change in optical properties from Fe2O3 over to a composition containing about 18 per cent. FeO, at which point the opacity of the oxide becomes so great that it is impossible to obtain measurements at higher percentages of ferrous iron. Natural oxides of iron intermediate in composition between Fe2O3 and Fe3O4 are much more common than is generally supposed. If a mineral oxide is not strongly attracted by a small hand magnet and if it gives a red streak, it is usually labeled "hematite." If it is strongly attracted by the hand magnet it is usually labeled "magnetite" without further tests. As we shall show later, oxides containing from 1 up to 31 per cent. FeO can be thus erroneously lumped together as "magnetite." It is a fact, nevertheless, that the great bulk of natural oxides of iron lie fairly near either Fe2O3 or Fe3O4 in composition. The reason will be

Jan 1, 1918

By Kosuke Hosoda, Shuji Owada, Hiroyuki Tokuichi, Hirobumi Ohta, Chiharu Tokoro, Moto-o Sato, Katsushi Okumura, Hiroto Ogawa, Hideaki Umezawa

The Japanese government enforced the "Small Domestic Appliances (SDAs) Recycling Law" in 2013. The law targets metals such as Ta, Nd, Dy, Co, and W to be recycled. Considerable amounts of these minor rare metals are mounted on printed circuit boards (PCBs) of the SDAs and/or e-scrap (electric and electronic scraps). Although precious metals and copper can be recovered from the e-scrap in non-ferrous metals smelters, most of the minor rare metals report to the slag in these smelters in non-recoverable forms. These metals are often used in particular types of devices, and therefore it is possible to concentrate them by separating such devices before feeding to the smelters. In previous work we developed technology for "Device Separation" to concentrate several minor rare metals, but some problems remained, such as how to remove the PCBs from e-scrap bodies, and how to detach devices from PCBs after their removal from escrap bodies. This paper proposes a two-stage crushing process in which, firstly, PCBs are removed from the e-scrap body with various crushers, and secondly, devices are detached from the PCBs involving the application of elevated temperatures. It was found that in the first stage, crushers with physically flexible rotating media such as chains, which provide high collision probability with the sample and consume relatively low energy, can quite effectively separate the PCBs from the e-scrap bodies non-destructively. In the second stage, heating was found to be remarkably effective in helping to detach mounted devices from PCBs, also non-destructively. This paper will also discuss the detailed mechanism of the heating effect on the detachment of devices from PCBs.

Jan 1, 2014

By H Zhang, Y Wang, S Sukenaga, H W. Ni, H Shibata, W Z. Mu

The crystallisation behaviour of low melting point CaO-SiO2-Al2O3-MgO inclusions greatly affect the deformability of inclusions during the rolling process. The crystallisation characteristics of CaO-SiO2- Al2O3-MgO melts representing the oxide inclusions in Si-Mn killed steel were systematically investigated. The effect of Al2O3 and MgO contents on the crystallisation change were analysed under a fixed CaO/SiO2 in the complex inclusions. The continuous-cooling-transformation (CCT) and time-temperature-transformation (TTT) experiments were conducted. The results showed that the increase of MgO content increases the crystallisation ability of CaO-SiO2-Al2O3-MgO inclusions, while the increase of Al2O3 content has the opposite effect. The viscosity, liquidus temperature of oxide melt and also the initial crystallisation potential might be the reasons for the change in crystallisation behaviour. Also, the crystallisation activation energy could semi-quantitatively characterise the crystal growth during the crystallisation of inclusions. To obtain low melting point plasticized CaO-SiO2-Al2O3-MgO (CaO/SiO2=1) system inclusions, the Al2O3 content of the system needs to be controlled larger than 15 wt per cent and the MgO content should be kept at a small amount.

Aug 21, 2024

By Z. Mullard

The introduction of social media platforms has ushered in a new era of interaction and information exchange, which impact business-to-society relationships. Mining companies are closely watching these platforms, as the industry takes a cautious approach to control flows of information. This paper explores the risks, challenges and opportunities of using social media, based on a qualitative mixed methods investigation with stakeholders from the Canadian mining industry. Generational and language barriers, misunderstanding and limited motivation from regulators make implementing social media platforms challenging and risky at an organizational level. The benefits of social media include being able to mobilize communities and share information in real time. Despite the challenges, the study found that 62% of mining stakeholders are incorporating social media tools, mostly in an ad hoc manner. Flexible strategies for transparent communication and public engagement are creating new opportunities for information exchange.

Jan 1, 2011

By Z. Zhang, Zongshu Zou, Nan Wang

"Thermodynamic calculation is applied to make an investigation on the equilibrium phase relations and liquids of CaO-SiO2-Al2O3-FeOx system for different temperatures. The calculated results with FactSage6.1 show that the effect of temperature on the the equilibrium phase relations and liquidus of CaO-SiO2-Al2O3-FeOx system and its sub-systems is appreciable. The liquid phase regions enlarge with increasing temperature from 1573K to 1873K, while the primary phase fields reduce distinctly.IntroductionThe main oxide components of vitrified bottom ash slag are CaO, Al2O3, SiO2, Fe2O3, MgO, and Na2O, accounting for more than 90% of the bottom ash by weight[1]. During slag processing, the knowledge of thermodynamic properties and liquidus temperature in the related slag systems is highly required [2, 3], which is not yet available. Through literature survey [4-6], it is clear that the systematic information on the concerned complex slag system is scarce. So far the engineers in the field have to make assumptions of the thermodynamic properties of the simplified oxide system, without taking into consideration the interactions of the different oxide components, which hinders the development of the slag valorization and utilization. In order to provide thermodynamic properties for the application of the vitrified bottom ash, the six-component oxide system (CaO-MgO-Al2O3-SiO2-FeOx-Na2O) is highly required. A preliminary phase diagram of the CaO-MgO-Al2O3-SiO2-FeOx-Na2O system can be obtained from extrapolation of the thermodynamic functions of constituent subsystems such as CaO-SiO2-FeOx-MgO, CaO-SiO2-FeOx-Al2O3, CaO-SiO2-Na2O-MgO and CaO-SiO2-Na2O-Al2O3. In this work, the equilibrium phase relation and liquidus of CaO-SiO2-FeOx-Al2O3 system, one subsystem of the concerned complex slag system, are calculated and the effect of temperature is also discussed."

Jan 1, 2012

A great part of the research on froth flotation of gold ores deals with ores containing gold associated mainly with sulphides, resulting in a largely accepted view that what takes place with sulphides (eg pyrite) in a flotation cell also happens to gold particles. This paper is concerned with the influence of some inorganics (CuSO4, CaO and NaCN) on gold particles flotation, using ethyl or amyl xanthates as collectors. The bench-scale tests were carried out with ground quartz and gold particles mixtures. Some findings stemmed from this study: flotation of the gold particles of size 0.16 mm was efficient adding only frother; larger gold grains were better recovered by the use of stronger collector CuSO4 did not seem to be an activator for gold; the addition of NaCN up to 200 g/t or CaO up to 2000 g/t did not depress the gold grains when amyl xanthate was used as collector although with ethyl xanthate the gold depression was verified.

Jan 1, 1993

By ZHANG Ting

In view of the high consumption and contamination of traditional vanadium extraction technology, a new process of leaching the converter vanadium slag without roasting with titanium dioxide waste was proposed. Extraction mechanism of P204 in the leaching solution had been researched and single factor experiments show that after a prereduction of Fe, and under conditions: ambient temperature，leaching solution original pH=2.5, phase ratio (A/O)=1:3, shaking time 8min, the extraction rate of V is more than 98.62% meanwhile the separation rate between V and Fe is up to 135.3 in the 20%P204-10%TBP-Sulfonated kerosene extraction system.

Jan 1, 2015

By Juliana Cecília Costa Ribeiro Vieira

As operações de amostragem de qualquer atividade que necessite de controle de qualidade são fundamentais tanto para fins de garantia da qualidade quanto para efeito comercial dos produtos. Na mineração de ferro não é diferente. Uma amostragem que carregue um vício de 0,20% no teor de Fe (%) pode representar uma perda de faturamento de aproximadamente US$226 mil para cada milhão de toneladas comercializadas aos preços atuais. Para fazer um bom plano de amostragem é necessário conhecer o grau de heterogeneidade ou variação de qualidade (sW) do minério a ser amostrado. Segundo Pierre Maurice Gy, um dos mais renomados especialistas em amostragem de minérios em geral, a forma mais indicada para estimar a sW é o método do variograma. Neste trabalho usamos a metodologia do variograma, com base na Norma Técnica ABNT ISO 3084:2003, para estimar a sW do minério tipo Sinter Feed produzido na Mina de Serra Azul da ArcelorMittal.

Oct 30, 2017

By Lucas Teixeira Costa

Por meio de modelamento matemático dos processos de dessulfuração de gusa e aço, em processo KR e forno panela, respectivamente, o presente trabalho tem como objetivo estabelecer rotas de produção de aços proporcionando aumento da produtividade e redução de custos. Foram avaliadas as seguintes rotas de produção: dessulfuração apenas no aço, dessulfuração apenas no gusa e dessulfuração no gusa e no aço, quais os produtos podem ser obtidos em cada rota de tratamento e quais as condições para a fabricação de aço baixo enxofre, com teores abaixo de 20ppm. Além disso, desenvolveu-se um balanço de enxofre para o LD e um estudo dos fatores que mais impactam a reversão ou a dessulfuração nessa etapa da fabricação do aço. Ao final, foram determinadas faixas de trabalho que permitam ganhos integrados dos três processos e um modelo global de enxofre capaz de prever bons resultados para diferentes plantas e contingências operacionais de diferentes usinas.

Aug 16, 2017

By Beatriz Cardoso Mendes

O presente trabalho tem como objetivo estudar a viabilidade do uso e a influência do ácido cítrico nas propriedades de pastas e argamassas feitas com cimento Portland CPV ARI, tanto no estado fresco quanto no endurecido. As dosagens de ácido cítrico utilizadas foram 0, 0,4% e 0,8% em relação à massa do aglomerante. Nas pastas de cimento produzidas, foram feitos ensaios de determinação da água de consistência normal e tempo de início e fim de pega. Já nas argamassas foram realizados ensaios de determinação do índice de consistência, densidade de massa, teor de ar incorporado no estado fresco, resistência à compressão axial, nas idades de 7, 14 e 28 dias e análises por meio da técnica de DRX. Os resultados mostram que o ácido cítrico, além de melhorar a trabalhabilidade da massa, contribui para aumento na resistência mecânica nas idades superiores a 14 dias, desde que aplicado em teores aceitáveis.

Jan 16, 2018

By J. K. Horbaczewski

The reclamation of an open dragline pit (Pond A3P-2) at the Gibbons Creek lignite mine in east-central Texas required neutralization of acid mine pit water. At the start of treatment with hydrated lime (Ca(OH)2) on March 28, 2000, the pond had partially filled with 913,000 m3 (740 acre ft) of pH 4.9 water. Another 666,600 m3 (540 acre ft) of pH 3.3 water was pumped in from an adjacent pit (PitA3P- 1). By the end of the project (July 5, 2000), a combined volume of 1,579,000m3(1,280ac-ft or 417milliongal) in PondA3P-2 had been successfully treated to pH 8.2 with 431 t (475 st) of lime. This was two to three times more neutralizer than laboratory trials and detailed chemical titration had predicted. The main reasons for the difference are thought to be the inadequate representation in a laboratory setting of some of the chemical reactions that occurred in the field, including incomplete mixing of reactants, reactions with clay minerals in the pit walls, the kinetics of biologically-mediated reactions and the kinetics of aluminum oxyhydroxide polymerization (aging).

Jan 1, 2002

By Andrea Pedroza da Rocha Santos

Neste trabalho, amostras de aço Lean Duplex UNS S32304 foram submetidas à temperatura de 800°C em um forno acoplado a um difratômetro de raios-x durante intervalos de tempo de 30, 60 e 90 minutos. Com o objetivo de analisar em tempo real a transformação das fases constituintes, foram realizadas várias varreduras insitu durante os diferentes tempos de permanência em 800°C deste material. Assim, observou-se a formação da fase sigma neste aço, tanto nos contornos de grão da ferrita como nas interfaces ferrita/austenita. Os valores de fase sigma obtidos para cada tempo de exposição foram calculados através do método de Rietveld sobre cada difratograma obtido e variaram de 11% a 17%. Notou-se que a fase sigma exibiu crescimento contínuo até 60 minutos e variação após este período. Todavia, observou-se que a formação de fase sigma a 800°C ocorre de forma significativa neste material após 30 minutos de aquecimento, o que pode comprometer as propriedades do mesmo.

Aug 16, 2017

By Roberto Pimentel de Souza, Helder Zenóbio

VRD started producing pellets in 1969 with one 2-million-t straight grate plant. In the beginning of April 1973, the second unit came on stream with an additional capacity of 3 million t/a of pellets. In January 1977, the third unit started, bringing the annual capacity to 8 million t/a. In the coming year (1978-79), three more units, 3 million t each, are expected to begin production. CVRD's experience with different binders and additives is described. Over the years several kinds of pellets have been produced to satisfy market requirements. General quality information is given for each.

Jan 1, 1981

By Nicholas J. Grant, Hanna Ibach, Bill C. Giessen

The system Ta-Rh was investigated over the entire comnposition range using metallogvaphic and X-ray techniques as well as thermal analysis. Terminal solubility limits, solidus temperatures, and the crystal structures of two new intermediate phases were determined. There are five intermediate phases: o, tetragonal, isostructural with o(Fe-Cr); a1, orthorhomnbic : a2, orthorhombic, isostructural with CozSi; 0 3, a high -temperature phase of unknozun structure; and a TaRh3, cubic, AuCu3 structure. a, aL, a,, and a melt peritectically; and a TaRh, has a maximum melting point. Five peritectic and one eutectic reactions occur. THE Ta-Rh phase diagram has not been fully treated in the literature; however, two inter metallic phases have been described.&apos;-&apos; This study attempts to work out the diagram covering the details of phase boundaries as well as the crystallography of the intermediate phases. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by National Research Corp., Cambridge, Mass., and rhodium powder of 99.9 pct purity, supplied by Bishop Co., Malvern, Pa. Analyses as given by the manufacturers are presented in Table I. In addition to the spectroscopic analysis, an oxygen analysis has been made of the tantalum powder. After preliminary trials, the standard procedure employed in making the alloys was as follows (see Ref. 4 for further details). The powders were weighed, mixed manually, compacted under 16,000 psi, and arc-melted at not more than 500 amp under thoroughly titanium gettered welding-grade argon of 400 mm Hg pressure. The gettering process was repeated after each melt. It had been shown previously5 that under these conditions no oxygen pick-up exceeding 0.001 pct in a hafnium button could be detected. The buttons, ranging from 5 to 10 g in weight, were inverted or, if possible, crushed and remelted three times. Melting presented no difficulty, except for tantalum-rich al- loys, which showed considerable spashing during melting. The average weight loss of 1 wt pct rose to 2.5 wt pct in these cases. Subsequent melting, however, resulted in losses of less than 0.1 wt pct. The melts obtained frequently showed small in-homogeneities, mostly in the tantalum-rich part of the system below 25 at. pct Rh. This was not due to insufficient blending of the elements, but to crystallization taking place from the cooled bottom. This condition was not improved by further re-melting; therefore the following precautions were taken. Cross sections of as-cast buttons were made. For the investigation only buttons were used where these inhomogeneities did not exceed 1 at. pct (estimated from the amounts of haSeS resent). In addition, only the center portions of such buttdns were utilized to minimize errors. Smaller buttons showed smaller concentration gradients and were used as a check. Finally, all alloys were homogenized to eliminate coring (see below). After this, the error in alloy composition due to inhomogeneity was cl at. pct. In order to confirm the concentrations of the alloys and to provide an impurity check, wet-chemical analyses and oxygen-fusion analyses of four key alloys were carried out. The results, together with the concentrations as calculated with the weight balance method, are presented in Table 11. It was found that for three alloys the agreement is very good (< 0.2

Jan 1, 1964

By S. W. Ip

Over the years, the importance of surface and interfacial phenomena has been neglected by the copper-nickel industry. As a result, little data on the surface and interfacial tension of the Ni matte and slag system are available in the literature. In view of the scarcity of information in this area, the surface tensions of the Ni-Fe-S system together with the Ni-Fe-S and fayalite type slag system were measured using the sessile drop technique. Drop images were obtained by X-ray radiography. For the Ni-Fe-S system, the results showed that the surface tension of the matte increases with matte grade. The surface tension behavior with changing matte grade showed a slight negative deviation from ideality. This indicated that FeS is slightly surface active in the nickel matte system. Results also indicated that small increase in sulphur content in the matte can decrease the surface tension quite significantly. The measured surface tension of the Ni-Cu-S system showed a linear relationship with the Cu2S content in the matte. The surface tension decreased with Cu2S content. Interfacial tension measurements showed a similar trend. That is, interfacial tension increased with increasing matte grade. The presence of MgO (-1.5%) and A12O3 (-6%) in the slag does not affect the interfacial tension value. Effects of matte surface tension on phenomena such as entrainment of matte in slag and infiltration of matte into refractory pores are discussed. The calculated flotation coefficients indicated that flotation of nickel mattes cannot be avoided by changing the matte grade. Filming of matte on bubbles can occur below a matte grade of about 19% Ni3S2. As for infiltration, refractory bricks containing high Cr2O3 will be easily wetted by matte regardless of matte grade. Therefore, bricks containing high Cr2O3 can easily be infiltrated by liquid matte.

Jan 1, 1993

Tellurium (Te) is one of the least abundant elements in the crust and tends to form minerals associated with copper, lead, zinc and iron sulfide deposits. Today, most tellurium production comes from the anode slimes and other wastes generated in metal refining. Most of the current tellurium produced in the world is used as an alloying agent in iron and steel, as catalysts, and in the chemical industry. However, future demand and production could increase because tellurium is increasingly used in solar panels and some electronic devices. Tellurium minerals are found in Au-Ag districts in New Mexico, but were not considered important exploration targets in the past. In New Mexico, tellurium is found associated with porphyry copper deposits in southwestern New Mexico and with Au-Ag veins in the Eureka, Sylvanite, Organ, Lordsburg, Steeple Rock, Wilcox, Mogollon, Chloride, Cuchillo, Hillsboro, Zuni Mountains, White Oaks, and Nogal-Bonito districts. The only tellurium production from New Mexico has been from the Lone Pine deposit (Wilcox district), where approximately 5 tons of tellurium ore was produced. Gold-tellurides are found with gold, silver, pyrite, and fluorite in fracture-filling veins in rhyolite at Lone Pine, with reported assays as much as 5,000 ppm Te. Other districts in New Mexico have potential for tellurium, but require field evaluation.

Feb 27, 2013

By Takao Oishi, Go Ohara, Toru Kitazaki, Masahiro Tanaka

"The High Pressure Acid Leach (HPAL) plant for nickel-cobalt mixed sulphide production at Coral Bay Nickel Corporation (CBNC) in the Philippines has been in operation since 2005 with a capacity of 10,000 t/year of nickel. Subsequent to the commissioning of the second plant in 2008, the production capacity increased to 22,000 t/year of nickel (Llerin et al., 2011). CBNC’s annual nickel production reached more than 24,000 tons of nickel in 2014. The concepts to achieve this capacity are the high availability and the reciprocally flexible operation of both plants. The availability depends on some factors, such as the control of impurities in the process and the equipment condition, to mention a few. In the HPAL process, it is not only the autoclave operating conditions that affect nickel extraction but also the impurities in the ore greatly influence it. The major element in the ore is iron and most of this iron is precipitated as Fe2O3, while the rest remains as Fe2+ or Fe3+ sulphate in solution. These ions in solution reduce the availability, so it is important to control the formation of iron ions by controlling the impurities in feed ore as well as the HPAL conditions. This paper presents the general HPAL process and the behaviour of impurities, focusing on iron behaviour in the HPAL process.INTRODUCTIONCoral Bay Nickel Corporation ProfileCoral Bay Nickel Corporation (CBNC) was founded on April 2002, as a joint venture of four companies; namely, Mitsui Corporation (18%), Sojitz Corporation (18%), Nickel Asia Corporation (10%) and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 54%. Aside from its capital share, Nickel Asia Corporation also supplies the ore and limestone for the High Pressure Acid Leach (HPAL) plant located in Rio Tuba, Philippines, as shown in Figure 1 (Tsuchida, 2008). The objective of the CBNC project is to produce 22,000 t/year (original design) of nickel and 1,500 t/year of cobalt, as sulphide, by the treatment of nickel laterite ore which is a low grade nickel oxide ore in the Philippines (Mines and Geosciences Bureau, 2014). The sulphide product has been exported as a raw material to the SMM Nickel Refinery in Japan for 30 years. The product of this plant, a mixed (Ni/Co) sulphide, is shipped to the SMM’s Nickel Refinery in Niihama, Japan. SMM Corporation provides the technology and management personnel to the plant. SMM Corporation also supplies the sulphuric acid, which is the main reagent for the HPAL process."

Jan 1, 2016

By Artur Frederico Fonseca da Cruz

Com a necessidade urgente e constante de aumento da competitividade no cenário atual da mineração, mostra-se fundamental o desenvolvimento constante de novos parâmetros de processo combinados a uma estratégia de manutenção focada não só na disponibilidade dos ativos, e sim no desempenho dos equipamentos. No que tange ao processo de pelotização neste trabalho foi dado foco especificamente na configuração de perfis de queima no forno de grelha móvel, onde foram testados quatro perfis e fixado o perfil nº 04 otimizado via sistema de otimização de processo para níveis de produções diferentes, equilibrando qualidade e consumo específico de gás natural, no período anterior e posterior à parada fria. A partir daí foram analisados parâmetros de qualidade, produção e processo, comparando-os entre antes e após a parada fria. Foram registradas melhoras nos índices de qualidade e redução de aproximadamente 13,50% do consumo específico de gás natural e 10,80% de redução no consumo específico de energia elétrica de ventiladores por níveis de produção.

Aug 17, 2017

By Rafael de Araujo Silva

As ligas ß-Ti têm sido consideradas materiais com potencial para armazenagem de hidrogênio no estado sólido. A adição de elementos de liga estabilizadores da fase ß, tal como o Nb, retém esta fase metaestável em temperatura ambiente. Neste trabalho a liga Ti-40Nb (at.%) foi produzida via fusão a arco e suas características microestruturais foram caracterizadas visando avaliar os efeitos da aplicação da deformação plástica severa (SPD, severe plastic deformation) e da hidrogenação. A laminação a frio sob atmosfera de Argônio foi a técnica de SPD escolhida. Os resultados principais mostraram que é possível hidrogenar a liga fundida Ti-40Nb em temperatura ambiente após laminação a frio. Os efeitos da deformação plástica severa na microestrutura da liga, como a introdução de discordâncias, foram importantes para o aperfeiçoamento da cinética de absorção em temperatura ambiente (25 °C). Após a dessorção da fase hidreto (CFC) a microestrutura volta a ser constituída pelas fases ? (CCC) e ?” (ortorrômbica).

Aug 17, 2017

By Severino Albani Junior

Descreve as atividades envolvidas no processo de inspeção e caldeiras de vasos de pressão instalados na usina ArcelorMittal Tubarão, localizada em Vitória - ES. Mostra que esses equipamentos possuem critérios rigorosos não somente para inspeção, mas também de fabricação e operação que necessitam obedecer a códigos de projetos e normas técnicas nacionais e internacionais com objetivo de garantir o funcionamento seguro. Aplica como ferramenta principal no suporte da gestão das atividades um sistema informatizado de manutenção, utilizado em toda usina. Utiliza como pilar na gestão das atividades de inspeção conceitos e ferramentas de planejamento, programação e controle e mostra a complexidade de fazer o controle dessas inspeções numa usina do porte dessa Siderúrgica, que possui uma planta industrial enorme tanto no tamanho, quanto no número de equipamentos e processos existentes. Destaca um grande avanço nos resultados obtidos na gestão das atividades de inspeção dos vasos de pressão e caldeira da ArcelorMittal Tubarão.

Aug 7, 2018