Search Documents

By Rodolfo da Silva Teixeira

As ligas de NiTi ricas em Ni tendem a exibir o efeito superelástico a temperatura ambiente. As amostras em estudo foram submetidas a tratamento térmico e mecânico a fim de avaliar o comportamento superelástico destas. Foram realizados ensaios a temperatura ambiente difração de Raios-X (DRX) para identificar as fases presentes e avaliaram-se as propriedades mecânicas via ensaios de ultramicrodureza instrumentada com pré-ciclagem térmica (aquecimento e resfriamento). Os resultados de ultramicrodureza instrumentada exibiram bons indicativos quanto ao uso prévio desta ferramenta para análises do comportamento superelástico destas ligas.

Oct 30, 2017

By B. McLaughlin

"The Penna shaft is the deepest single-lift shaft in North America. Agnico-Eagle started sinking the Penna shaft in 1995 with a hoisting plant capable of hoisting 1800 t/d from a 2240-m deep shaft. Exploration success at depth led to the replacement of the existing double drum hoist by another double drum hoist capable of hoisting 7000 t/d. The use of another double drum hoist, instead of a Blair multi-rope winder, to hoist 24.5 t skips was only made possible by lowering the safety factor.This paper describes recent experiences at Penna and in South Africa, and examines the possibility of extending the double drum hoisting system to a depth of 3 km. IntroductionThe original Penna production hoist was a 4.88 m (16 ft) diameter double drum and single clutch machine. Béliveau (1996) and Scott (1996) have described this hoisting plant. In 1998, a decision was made to increase mining capacity from 1800 t to 4500 t of ore per day from the shaft bottom. Final capacity had to include an allowance of 1800 t of waste per day for future capital projects. While daily capacity was to be 6300 t, it would, by taking into account the different rock densities, be equivalent to hoisting 7000 t of ore.The steps taken to lower the safety factor were presented by McLaughlin and Scott"

Jan 1, 2004

By Richard McCaffery

CONTENTS PAGE 1. Research on Blast-furnace Slags (A Progress Report). By Richard S. McCaffery 5 2. Determination of Viscosity of Iron Blast-furnace Slags. By Richard S. McCaffery, Clarence H. Lorig, Ira N. Goff, Joseph F. Oesterle and Oscar O. Fritsche 27 3. Effect of Magnesia on Slag Viscosity. By Richard S. McCaffery, Joseph F. Oesterle and Oscar O. Fritsche 55

Jan 1, 1931

By J. H. Swisher

The solubility of sulfur and rate of solution of sulfur in pure Lron were measured in H2S + H2 and H2S + H2 H2O gas mixtures. The solubility and diffusivity of sulfur at 1410°Care 0.13 pet S and 1.0 x 10-5 sq cm per sec, respectively. The solubility iS the same, but the rate of sulfurization is slower in the presence of H2O in the reacting gas. Under these conditions, the over-all rate is controlled jointly by a slow surface reaction and by solid-state diffusion; the mechanism for the surface reaction has not been identified. KNOWLEDGE of the behavior of sulfur in solid iron is desirable for the metallurgy of such products as free machining steel, where a high sulfur level is required, and inclusion-free high-strength steels, where the sulfur specifications are very low. The present investigation was undertaken to check previously reported values for sulfur solubility and diffusivity in 6 iron, and to study the poisoning effect of chemisorbed oxygen on sulfurization kinetics in H2-H2S-H2O gas mixtures. All of the experiments were performed at 1410°C. The thermodynamic behavior of sulfur in 6 iron was the subject of a paper by Rosenqvist and Dunicz.' The sulfur solubility at 1400" and 1500°C was determined by equilibrating pure iron specimens with H2-H2S gas mixtures. The maximum solubility of sulfur in 6 iron was alsc determined by Barloga, Bock, and parlee2 by reacting iron wires with sulfur in sealed capsules. In another investigation, the diffusion coefficient of sulfur in 6 iron at temperatures up to 1450°C was measured by Seibel.3 The method used was to measure sulfur concentration profiles in diffusion couples containing radioactive sulfur EXPERIMENTAL Apparatus. A vertical resistance furnace wound with molybdenum wire and containing a recrystallized alumina reaction rube was used for the experiments. The hot zone in the furnace was approximately 2 in. long with a temperature variation of ±3oC. The hot zone temperature was automatically controlled to within ±2°C, and the test temperature was measured with a pt/Pt-10 pet Rh thermocouple before and after each experiment. Flow rates of the reacting gases were obtained using capillary flow meters. Materials. The source of H2S in the gas train was a premixed cylinder containing 5 pet H2S in H2. This mixture then was diluted with additional hydrogen and argon. In some experiments, water vapor was introduced by passing hydrogen and argon through a column containing 10 pet anhydrous oxalic acid and 90 pet oxalic acid dihydrate. The vapor pressure of water above this mixture is well-known.4 Argon was used as a diluent to minimize thermal segregation of H2S in the furnace5 and to reach higher H2O:H2 ratios than could be obtained in mixtures of H2 and H2S alone. Argon was purified by passage over copper chips at 350°C and subsequently over anhydrone. Hydrogen was purified by passage over platinized asbestos at 450°C and then over anhydrone. The H2-H2S mixture was purified by passage over platinized asbestos and then over P2O5. The specimen stock was made by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zirconia crucible. The principal impurities are listed in Table I. In some of the equilibrium experiments, six-pass zone-refined iron was used to minimize impurity side effects. This zone-refined iron had a total impurity level of about 25 ppm. Procedure. Specimens were annealed in hydrogen for a period of at least 2 hr at the beginning of each experiment. The specimens were held in the reacting gas for times varying between 10 min and 17 hr, and cooled to room temperature in a water-cooled stainless-steel block at the bottom of the furnace. The pH2S/pH2 ratios reported are those for gas equilibrium at 1410°C. Calculations based on available thermodynamic data8 showed that the only other gaseous8 species that formed in significant amounts in the furnace were S2 and S. Even when water vapor was introduced into the gas mixture, the concentrations of SO2, SO, and so forth, were negligible. The initial partial pressure of H2S was therefore corrected for its partial dissociation to S2 and S in determining the equi-

Jan 1, 1968

By J. A. Dos Santos

High angle conveyor (HAC®) systems in open pit mining offer many advantages over the traditional, truck only, haulage systems, including: (1) superior energy efficiency, (2) less dependency on petroleum products, (3) less sensitivity to inflation, (4) less labor, (5) less excavation for the amount of ore recovered, and (6) less ramp construction and maintenance costs. Previous studies had revealed the technical and economic feasibility of high angle conveyors. This paper presents the Sandwich Belt HAC® as the vital link to optimization of in-pit conveying systems. HAC development to date is discussed, beginning with studies in 1979, to the first large scale prototype in 1983, to the first commercial unit in 1984, into "the latest commercial installations. Discussion continues with the HAC systems to suit the various open pit mining operations and the corresponding characteristics of the system components, particularly the high angle conveyor. The range of HAC systems from the low capacity (up to 1,814 t/h), low lift (10.7 to 36.6M), highly mobile to the moderate capacity (1,814 to 3,629 t/h), moderate lift (36.6 to 76.2M), intermittently mobile to the high capacity (greater than 3,629 t/h), high lift (greater than 76.2M), semi-mobile, are discussed along with some possible combinations of these.

Jan 1, 1989

By Charles M. Rolker

The Mariposa estate, a grant made by the Mexican Government to Juan 13. Alvarado, during the time when California was still under the dominion of Mexico, was purchased in 1847 by J. C. Fremont, and the United States patent issued to him in 1856. By sale, or its equivalent, money advanced, the property came into the hands of the Mariposa Company, June 25th, 1863, and through a varied existence of work and temporary inactivity, has as yet been kept as an undivided property, and rests at present with the Mariposa Land and Mining Company of California. I pass over this period of 15 years without giving the history of the ups and downs of the estate, partly because it is familiar to many, and also because I think in such a case this paper would assume too much the character of a narrative. The estate is situated in Mariposa County, California, about 170 miles southeast of San Francisco. It begins in lat. 37' 26' 38'' north, and long. 119' 55' west, and runs 6 miles north; thence 69 miles west; thence 5 miles northwesterly towards the Merced River; thence 84 miles southerly; thence 3 miles easterly; thence 1 mile southerly; thence 2 miles easterly; thence 2 miles southerly; thence 2 miles easterly; thence 1 mile southerly; thence 2 miles easterly; thence 1 mile northerly, and thence 2 miles easterly to the place of the beginning; embracing 44,387 acres (70 sq. miles) more or less. To describe this vast estate in detail as to its full geology, its numerous quartz veins, its many facilities to exploit them and work them by cheap methods, would lead me further than I intend to go at present, and I will content myself to describe the latest workings of the company and its immediate field of operations. As long ago as 1860 the late Dr. Adelberg advised the running of an adit from the northwestern edge of the estate at Benton Mills 011 the Mereed River. His object was to undercut the deepest workings of the then paying mines on the estate—the Pine Tree and Josephine. Following this advice, the tunnel known as "River Tunnel " was commenced. Its entrance is in S. 5, T. 4, s. R. 17 E. It is run in

Jan 1, 1879

By B. J. I. Adair, K. R. Weller

The bulk scavenger tailing from Aberfoyle's Hellyer Concentrator, which represents about one-third of the total tailing, runs about 2.5-3 g/t gold and 140-200 g/f silver. Both values are very finely disseminated, particularly the gold. Aberfoyle wished to establish whether ultra-fine grinding followed directly by cyanide leaching could be applied to the tailing for recovery of gold and silver. The work comprised the determination of gold and silver recoveries as a function of grind size and leaching time, the specific energy consumption required for continuous wet grinding of the tailing to the specified product size in a small horizontal continuous stirred mill, and an estimate of the rate of media consumption. The maximum extraction of gold, 23.3% was obtained from the finest product, with the highest cyanide concentration and longest leach time, confirming earlier work. A similar result was obtained for silver. The specific energy requirement for milling rose from 27.7 kWh/t for a P80 of 8.1 um to 219 kWh/t for a Pea of 2.3 um. The consumption of ceramic media was about 1.6 g/kg of final product. An extensive QEM'SEM Trace Mineral Search on the unground tailing failed to identify any gold-bearing particles but did identify silver-bearing particles which displayed a variety of textural associations and liberation characteristics.

Jan 1, 1998

By Rômulo Albertini Rigueira

A fratura por fadiga é a forma mais comum de falha estrutural e, atualmente, é um problema desafiador no projeto de componentes mecânicos. O objetivo desta pesquisa foi modelar matematicamente as curvas de crescimento de trinca por fadiga em função do fator de intensidade de tensão de uma junta de aço 1016 obtida pelo processo de soldagem GMAW. Os resultados obtidos no estágio II da curva de propagação de trinca por fadiga mostraram que o material respeita a equação de Paris para solicitação no sentido longitudinal. No entanto, verificou-se uma correlação linear entre os parâmetros. Esta correlação deixa de existir quando se trabalha com o modelo de Bergner. Não houve variação no crescimento de trinca por fadiga na direção TL, analisado segundo o modelo de Bergner e na região fundida.

Aug 16, 2017

By P. D. Zemany, G. W. Sear, B. W. Roberts

Vanadium metal is embrittled by hydrogen at a temperature as low as 250°C when held in the presence of manganese metal and water vapor in a rough vacuum. It is established that the property changes are caused by the catalytic decomposition of water vapor at the vanadium surface and the diffusion into and solution in the vanadium of the resultant hydrogen. It is found that manganese is a necessary component of the catalyst. The manganese is transported in the vapor phase by an unknown molecule. A deuterium tracer experiment demonstates the role of water vapor in the embrittle-ment process. VANADIUM metal foils were observed to become embrittled' at a temperature of about 300 °C when held in the presence of manganese metal and a small amount of moist air, This paper describes the investigation to find the embrittling agent and an understanding of the relatively low temperature reactions that are involved. Experimental The vanadium metal foil used was prepared by cold-rolling and pack-rolling 32 mil sheet" in a series of steps down to 1 mil foil. The original observation was confirmed by sealing vanadium foils of 3 x 10 sq cm into individual Pyrex tubes with manganese powder† and a con- trol tube containing only the vanadium foil. These tubes were evacuated to 10 -5 mm Hg without baking and sealed. After heat treatment for 200 hr at 300°C, the control foil showed no change in duetility, whereas the foil contained in the manganese— containing tube was embrittled. The visual appearance of each was unchanged. A series of Pyrex sample tubes, about 2.5 cm diam and 25 cm long, were prepared, each containing a 3 x 10 sq cm piece of foil and 5 g manganese powder at the lower end of the tube. By reducing the time of anneal and the temperature of these samples, it was found that embrittlement could be created at 250°C in a time as short as 1 hr. Since the vanadium metal used here has been drastically cold-worked by rolling, it is assumed that it contains a maximum number of dislocations. To check the possible necessity of dislocations in this low temperature reaction, a vanadium foil sample was annealed in Vycor for 2 hr at 800°C to re crystallize and reduce the dislocation concentration. Metallographic examination showed grains which were not visible before annealing. The embrittlement procedure was carried out at 300°C and 3 hr. Upon checking the foil no embrittlement was observed. Further experiments demonstrated that about 6 hr at 300°C are required to create embrittlement in the foil. This delay in the onset of embrittlement in the vanadium foil suggests but does not prove that dislocation channels play a role in the embrittlement phenomena. If manganese metal is necessary for this low temperature embrittlement, do other elements in the transition metals group yield the same result? To check this qualitatively, a group of elements of similar atomic radii were obtained and sealed as before into Pyrex tubes with a sheet of vanadium foil. These tubes were annealed at 250°C for 6 hr and included (with radii)-2 A1 (1.4A), As (1.25A), Be (1.2A), Co (1.25A), Cr (1.45A), Cu (1.25A), Fe (1.25A), Ga (1.2A), Ge (1.25L%), Mn (1.3A), Ni (1.25A), Si (1.2A), Ti (1.45A), Zn (1.3A), air, H,O, 10 cm Hg of dry hydrogen, and MnO, powder. Upon testing the above sample foils for brittleness, only the manganese-containing tube yielded a brittle foil. Manganese Transport—To eliminate contact of manganese metal powder and vanadium foil, sample tubes were prepared with fritted glass barriers. The embrittlement reaction was still found to occur. Thus, the mode of transfer of manganese is certainly vapor transport. A vanadium foil was embrittled by this mechanism in an evacuated Pyrex tube for 8 hr at 300°C. By means of X-ray fluorescence analysis,' the amount of manganese added to the surface was established at 5 ±2 x 10 -6 g per sq cm. Since the average rate of manganese deposition is known, an effective average pressure of an assumed carrier compound can be computed. ___ P = M/T v2p mkT

Jan 1, 1959

By Ana Paula Domingos Cardoso

Este trabalho descreve o desenvolvimento, as características técnicas para a produção do produto Usibor® 1500 pela ArcelorMittal. A viabilidade de produção destes materiais é decorrente do processo de otimização de operação e infraestrutura da sua linha de galvanização (Continuos Galvanizing Line). O trabalho engloba também características técnicas gerais do produto, microstruturais e mecânicas, assegurando conformidade com normas internacionais de qualidade do mesmo. Afim de conhecer a microestrutura e propriedades mecânicas do material Usibor®1500, antes e após conformação a quente será apresentados resultados de aplicação do material estampado industrialmente no setor automobilístico.

Aug 17, 2017

By Antonio Regio Avancini

Nos últimos anos Vitória vem sendo fortemente afetada por chuvas torrenciais em um curto período de tempo. Para garantir a segurança dos trabalhadores e equipamentos como também reestabelecer as condições normais de trabalho num menor intervalo de tempo, foi necessário rever e criar alguns procedimentos com o intuito de mitigar o efeito das chuvas. Os procedimentos são voltados principalmente a melhor manutenção das galerias de escoamento de água, melhorias no sistema de drenagem dos pátios, redução de altura das pilhas de matérias-primas, melhorias nos procedimentos de recuperação das matérias-primas dos pátios.

Aug 16, 2017

By Kleidon Rodrigues de Almeida

O presente projeto descreve um trabalho de otimização dos ensaios laboratoriais de liberação do produto para fins elétricos na CSN (Companhia Siderúrgica Nacional), sendo tema de um projeto Lean Six Sigma. O foco do projeto foi otimizar os ensaios de epstein, tração e dureza, reduzindo o Lead Time de liberação dos produtos para fins elétricos e a quantidade de ensaios realizados. Para a realização deste trabalho, fez-se o uso de ferramentas e métodos Lean Six Sigma, permitindo a busca dos resultados de maneira sistêmica, superando as metas estabelecidas, gerando uma maior competitividade à empresa no mercado. Obteve-se com este projeto uma forte redução do Lead Time e da quantidade dos ensaios laboratoriais dentro de um prazo estabelecido, permitindo uma liberação para faturamento no mesmo dia de produção em 80% da produção deste produto.

Aug 7, 2018

By Jezuele Milanez

No ano de 2016 foi desenvolvido um importante projeto na Gerdau Mineração relativo ao pilar produtividade: a consolidação da Manutenção Compartilhada na Gerência do Beneficiamento Mineral. A Manutenção Compartilhada, ou autônoma, é um programa que capacita os colaboradores a realizar manutenção, pequenas inspeções, além das operações das plantas de beneficiamento, através da criação da carreira de Operador Mantenedor em sua estrutura. Alinhado com o mapa estratégico da unidade, o projeto teve por objetivo consolidar um novo conceito de estrutura de carreira das equipes de Operação e Manutenção nas plantas de beneficiamento. Buscando maior simplicidade, aumento da produtividade e capturando as oportunidades de sinergia entre as equipes de Operação e Manutenção, o projeto reduziu significativamente o custo de pessoal e resultou em maior autonomia e oportunidades de crescimento para as equipes envolvidas.

Oct 30, 2017

By Fábio Lerbach

Balanço Energético Global da Vallourec Sumitomo Soluções Tubulares do Brasil site Barreiro em 2016, com os principais indicadores de consumo energético das áreas consumidoras. Além dos indicacores energéticos globais, o balanço apresenta os consumos específicos de cada insumo nas diversas áreas, permitindo a análise de cada setor da Usina, isoladamente.

Jan 26, 2018

By E. J. Marcotte

"INTRODUCTIONThe Upper Canada Mine is located at Dobie, approximately ten miles east of Kirkland Lake, Ontario.The mill contains Upper Canada's cyanide circuit and Upper Beaver's flotation circuit. The combined capacity is 590 tons per day consisting of 415 t.p.d. of Upper Canada gold ore and 175 t.p.d. of Upper Beaver copper-gold ore.The Upper Beaver ore is trucked five miles to the Upper Canada mine site.Crushing:The crushing circuit consists of primary, secondary and tertiary crushing employing one C .A. C. 15 in. x 24 in. Superior jaw crusher, one 4 ft. x 8 ft. Tyler-Niagara double deck screen, one 3 ft. Symons standard cone crusher and one 3 ft. Symons shorthead cone crusher.The -2 in. product from the jaw crusher is fed to the double deck screen. The+ 5/ 8 in. passes over the top deck to the 3 ft. standard cone crusher; the+ 3/ 16 in. material passes over the lower deck to the shorthead cone crusher. The - 3 / 16 in. material pas sing through the lower deck of screens is the product to the mill.The screens used prior to the installation of rubber screen cloths were: one 4 ft. x 4 ft. section with 3/ 4 in. square openings and one 4 ft. x 4 ft. section with 5/ 8 in. square openings on the top deck; two 4 ft. x 4 ft. sections with openings of 3/16 in. x 4 1/2 in. slot on the lower deck. The fine screens were positioned so that the 4 1/ 2 in. slots were parallel to the flow of feed.The crushing circuit is operated on a three shift per day basis by one operator per shift."

Jan 1, 1968

By Alexandra de Almeida Diego

O controle da transferência de calor é uma das principais funções que o fluxante exerce durante aplicação no molde de lingotamento contínuo. O fluxo de calor na interface placa / molde deve estar adequado aos parâmetros de processo e ao tipo de aço, caso contrário pode provocar preferencialmente alarmes de agarramento em aços baixo carbono e trincas longitudinais em aços médio carbono, podendo levar até ao breakout. Este trabalho tem o objetivo de caracterizar os filmes de escória aplicados em aços baixo (Filme BC) e médio carbono (Filme MC), ambos comerciais, utilizando as análises de Microscopia Eletrônica de Varredura (MEV) com Energia Dispersiva de raios-X (EDS) acoplado e Difratometria de raios-X (DRX). As diferenças entre os filmes de escórias foram discutidas e relacionadas aos dados presentes na literatura.

Aug 16, 2017

Microorganisms are finding more use in the mineral industry, with extensive research efforts being reported in 1991. Most of these research efforts were presented in two major meetings, the SME Annual Meeting in Denver (February, 1991) and the Engineering Foundation Conference about Mineral Bioprocessing in Santa Barbara (June 1991). In addition, several articles were published in the IMM Transactions, Minerals and Metallurgical Processing and Water, Air. and Solid Pollution Journal. The literature can be categorized as: • Review articles presenting an overview of the activities in the use of biotechnology in mineral processing. • Research efforts into genetic manipulation of microorganisms to perform a specified job. • Studies in bioleaching of metals from different types of ores. • Biotreatment of wastes from the mineral industry including acidic mine waters, uranium tailings, cyanide destruction, etc. • Investigations into the role of microorganisms in the energy materials, such as oil, coal, tar sands, oil shales, etc. Smith (Mineral Bioprocessing Conference) presented a review of research efforts as well as practical applications of biotechnology in the mineral industry. In another article, Smith et al. (Minerals Engineering) emphasized that extensive fundamentals and applied research work should be pursued to explore the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering.

Jan 1, 1992

By Laís Ávila de Oliveira Silva

A aplicação de ligas de NiTi como biomateriais exige que sua superfície tenha um excelente acabamento final, para garantir a alta resistência à corrosão e a biocompatibilidade. O polimento eletrolítico é um processo capaz de diminuir as imperfeições da superfície, sem alterar as propriedades do material, e de formar uma fina camada protetora de TiO2. Nesse estudo, foram realizados eletropolimentos em fios superelásticos e com memória de forma, usando dois eletrólitos ácidos distintos. A partir dos resultados obtidos, foi possível concluir que a solução de ácido sulfúrico produz superfícies mais homogêneas do que o de ácido perclórico, para os mesmos tempos de polimento, e se apresenta como uma boa alternativa para o tratamento superficial de ligas superelásticas e martensíticas de para sua aplicação como biomateriais.

Aug 17, 2017

By Cláudia Lisiane Fanezi da Rocha

Softwares desenvolvidos para análise das propriedades mecânicas em máquinas de ensaio de tração facilitam o trabalho rotineiro de caracterização dos materiais. No entanto, estes aplicativos não apresentam informações importantes como cálculos da incerteza de medição, cabendo uma análise da confiabilidade dos resultados obtidos por esses programas. O presente trabalho se propõe a comparar os valores dos limites de escoamento, de resistência, do módulo de elasticidade e da deformação final obtidos através do software Instron Bluehill® com os valores calculados através da análise minuciosa dos dados provenientes dos instrumentos de medição (célula de carga, extensômetro, sensor de deslocamento). Busca-se, assim, fornecer informações que auxiliem o trabalho de técnicos e engenheiros, além de estimar o erro percentual e desenvolver uma metodologia periódica para a garantia da confiabilidade da máquina de ensaio.

Aug 7, 2018

By Lindaura de Souza Cândido d'Avila

O presente trabalho é parte de um estudo mais abrangente que busca o desenvolvimento da mistura de diferentes tipos de minérios de ferro para a maximização da produtividade na sinterização. Essa etapa do estudo teve o intuito de avaliar as diferentes características do minério de ferro itabirítico e sua influência na produtividade da sinterização em escala piloto. Inicialmente foi realizada a caracterização dos minérios de ferro hematítico e itabirítico oriundos do Quadrilátero Ferrífero. Em seguida, foram testadas em escala piloto misturas de minério de ferro com proporções variadas de minério hematítico e itabirítico. A partir dos resultados de produtividade e de qualidade do sínter obtido foi possível avaliar o efeito do minério itabirítico na mistura de sinterização. Tais resultados indicam diferentes desempenhos desses parâmetros na unidade piloto de sinterização.

Aug 16, 2017