Search Documents

By M. C. Flemings, F. R. Mollard

Two-phase Pb-Sn alloys, ranging in compositiotz from 12 to 26 at. pct Pb, were unidirectionally solidified in a convection-fvee system, with thermal gradients in the liquid of up to 480°C per cm. Plane front solidification Loas achieved in all alloys at sufficiently steep gradient and slow growth rate. Conditions causing breakdown of the interface to a cellular or dendritic structure were roughly as predicted by a sinlple constitutional supercooling criterion. Structures of alloys of near-eutectic composition, solidified with plane front, exhibited a lamellar structure; the alloys furthest from the eutectic exhibited a rod-like morphology. Assumptions used in a previous paper for calculations of solute redistribution in two-phase plane front growth are shown to be reasonable for Pb-Sn alloys. Results of calculations are in good agveement with experiment. These show that variations in growth rate during solidification of the composite produce marked changes in average composition of the solid. IN a previous paper, Part I,' conditions necessary for plane front solidification of two-phase alloys were discussed and calculations given on solute redistribution in this type of solidification. This paper, Part 11, describes experiments on Pb-Sn alloys, designed to check the assumptions of the analyses presented, and to demonstrate their applicability to a given alloy system (Pb-Sn). APPARATUS AND PROCEDURE General. A vertical crystal growing unit was built for the study as described below, and "normal solidification" employed throughout (i.e., the ingot was completely melted except for a portion near the bottom end and then solidification initiated). The furnace was designed to permit achieving very low interface velocities, and steep gradients, in essential absence of convection; it is sketched in Figs. 1 and 2. Simple heat flow considerations indicated choice of a small-diameter specimen (ingot) to achieve high thermal gradients; ingot size chosen was 0.3 cm in diam. The ingots were held inside silica tubes 0.06 cm wall thickness. The requirement for an essentially convection-free system was met by use of the vertical furnace with the heat source over the heat sink, as well as by use of the small diameter ingots. In addition, by selection of tin-rich Pb-Sn alloys, the diffusion boundary layer (lead-rich) was denser than the bulk liquid and would not cause convection. The only apparent driving force for convection in this system was the small transverse temperature gradient resulting from heat flow into the samples from the furnace. Such convection must have been small, however, since 1) no temperature fluctuations in the melt were noted in the recordings, which would have indicated turbulent convection, and 2) experimental results obtained and described below could not have been achieved in presence of significant convection. Ingot Preparation. Pb-Sn alloys ranging from 12 to 26 at. pct Pb were prepared from high-purity lead and tin (99.9999 pct pure metal). Each alloy was prepared by first melting the pure metals in the proper ratio in air, in a Pyrex container. The melt was then stirred thoroughly with a graphite rod and cast into a preheated graphite mold. Ingots were then prepared from these castings for use in the actual experiments; each ingot consisted of a rod of alloy, 15 cm long in a 25-cm-long transparent fused-silica tube, 0.3 cm ID and 0.06 cm wall thickness. One chromel-alumel thermocouple, made with 0.004-in.-diam wire and protected by a two-hole alumina tube, was inserted into each ingot. The 1.5 cm of the thermocouple nearest the bead were protruding from the alumina tube and were coated with a very thin layer of boron nitride paste which provided electrical insulation while allowing good heat conduction. The electrically welded junction size was about that of each wire and the cross section of the two wires represented about 0.3 pct of the sample cross section. Including the coating, the thermocouple cross section still represented less than 0.5 pct of the ingot cross

Jan 1, 1968

By James A. Sommers

Hydrolysis of NbC15 is used to recover oxide values for ceramic and metals production. Reaction of NbC15 with water is rapid, exothermic and vigorous, yielding a gelatinous slurry. In contrast, dissolution of NbC15 in 12 N HCl is endothermic, resulting in a clear yellow solution. Such solutions can be de-hydrochlorinated by controlled contact with air, to precipitate a tantalum¬rich solids, depleting the liquid of its tantalum content. In this way, cheap, useful Nb-Ta partial separation is achieved. The separation is based upon differential oxide-chloride stability. Nb2O5 with <200 ppm Ta/Nb has obtained from starting levels of 2000 ppm. Observations are made on the different types of hydrolysis.

Jan 1, 1992

By R. L. Virta

Sixteen companies mined fuller’s earth in 11 states during 2004. Production during 2004, based on a preliminary survey of fuller’s earth producers, was 3.96 Mt (4.3million st) valued at $340 million. This compared with3.6 Mt (3.9 million st) during 2003, valued at $346 million. The 3.96 Mt (4.3 million st) probably includes some crude clay tonnage. And production of finished product probably was closer to 3.2 Mt (3.5 million st) in 2004. Georgia was the leading producer state of attapulgite-type fuller’s earth, followed by Florida. Georgia also was the leading producer state for montmorillonite-type fuller’s earth. It was followed, in descending order, by Mississippi, Missouri, Florida, Virginia, Illinois, California, Tennessee, Kansas and Texas.

Jan 1, 2005

Jan 1, 1970

[Adams, Douglas K General Electric Co., P.O. Box 2331, Denver 1, Colo. Adams, Frank E U.S. Steel, 919 Kearns Bldg., Salt Lake City, Utah Alger, Van Kaiser Steel, Sunnyside, Utah Allan, Andrew Thompson Creek Coal & Coke Corp., Glenwood Springs, Colo. Allen, Earl W Mine Safety Appliances Co., 257 Rio Grand St., Salt Lake City, Utah Allen, Thomas Chief State Coal Mine Inspector, State Services Bldg., Denver, Colo. Anderson, Nephi W :Book Cliffs Coal Co., Dragerton, Utah Anderson, W. J Texaco, Inc., 845 N. 5th E., Price, Utah Ankeny, Marling J U. S. Bureau of Mines, 5308 Roosevelt St., Bethesda, Md. Arentzen, E. M Lee-Norse Co., Charleroi, Pa. Arentzen, L. E Lee-Norse Co., 2975 18th St., Boulder, Colo:]

Jan 1, 1961

Jan 1, 1970

Research by the National Institute for Occupational Safety and Health (NIOSH) on multiple-seam mining has resulted in two new ground control products. Information Circular (IC) 9495 In some U.S. coalfields, particularly in central Appalachia and the West, most mines are operating above and/or beneath previously mined seams. The effects of multiple-seam interactions can include roof falls, rib spalling, and floor heave. These can seriously threaten the safety of miners and disrupt mining operations. Information Circular (IC) 9495 is a proceedings document containing a variety of papers that summarize recent knowledge about multiple-seam mining. A NIOSH study that analyzed case histories collected from 44 U.S. coal mines is described in detail. The study confirmed that overmining is much more difficult than undermining, and isolated remnant pillars cause more problems than gob-solid boundaries. The study&apos;s results were the basis for the Analysis of Multiple-Seam Stability (AMSS) software package. The proceedings also contain two papers describing the LaModel family of software. The original three-dimensional version of LaModel is essential for detailed analyses of complex multiple-seam scenarios. LaM2D implements a simplified, two-dimensional model suitable for quick approximations of the multiple-seam stresses and strains. Three papers in the proceedings focus on case histories. One describes the extensive multiple-seam experience at the Harris No. 1 Mine in West Virginia, a second contains examples of "extreme" multiple-seam mining from the central Appalachian coalfields, and a third describes interactions with regard to longwall mine experiences in Pennsylvania, West Virginia, and Utah. The final paper reports on a numerical modeling study that provided some insight into the mechanics of multiple-seam mining. [ ] AMSS Software Package NIOSH has developed a simple, user-friendly computer program called Analysis of Multiple-Seam Stability (AMSS). AMSS can help mine planners to evaluate each potential multiple-seam interaction and take steps to reduce the risk of ground control failure. AMSS begins by evaluating the pillar design. It first calculates the single-seam pillar stability factor (SF)

Jan 11, 2007

By R. W. Vieth, S. A. Bradford

THE orientations of tetragonal tin crystals are commonly examined by either the transmission Laue method or the back-reflection Laue method. The predominant planes and zone axes of the pattern are plotted on a Wulff net and indexed by measuring the angles between planes and directions. The problem of identifying the Laue spots has been approached in several different ways. Nicholas 1 tabulated interplanar angles for ten planes but did not relate the angles to permutation of indices or sign. A table of angles between adjacent planes and of angles between adjacent zones was published by Chandrasekhar and veal.&apos; These tables are very helpful, provided the film shows all the low-order zones that occur within about 20 deg of each other. Frounfelker and Hirthe&apos;s compilation3 of angles between the (001) plane and twenty-nine other planes is useful for the indexing, only if the (001) spot can be found on the film. For all but the simplest orientations, however, more information is needed to index the diffraction spots. Standard stereographic projections, such as those published by Bicelli, 4 provide part of the information required. By their nature, these projections show the positions of only a few zone axes. In the tetragonal system many low-order zone axes are not normal to the planes having the same indices. Consequently, planes and directions can have entirely different positions on a stereographic projection. For example, the [011] zone axis is 33 deg from the normal to the (011) plane. The crystallographic orientation usually has to be deduced from a combination of the predominant zone axes and a few low-order planes that appear on the film. In addition to a standard stereographic projection of the planes, a stereographic projection of the directions is needed. Such a projection can be constructed from the angles given in Table I. To provide more information about angles between planes and directions, we have calculated interplanar angles up to (332) and angles between planes and directions up to [332] on an IBM 1620 computer. The angles are differentiated according to permutations of sign and indices. Those doing research on tin single crystals are welcome to request a copy of these tables from the authors.

Jan 1, 1967

Jan 1, 1968

By J. F. Smith, J. E. Davison

A value for the enthalpy of formation of z2 of -3.14 i 0.21 kcal per g-atom has been measured by the technique of acid solution calorimetry. This result is in quite good agreement with two earlier determinations by tin solution calorimetry and by direct reaction caloriinetry, and averaging of values determined from the three independent calorimetric techniques gives enhanced precision and accuracy with AHh8 (CaMgZ) = - 3.15 i 0.05 kcal per g-atom. For comparison with experimental data, values for the enthalpies of formation of CaMgz, SrMgz, and BaMgz of -9.8, -7.9, and -2.8 kcal per g-atom were estimated from a calculation based on the LVigizer-Seitz approximation as modified by Raimes for polyvalent elements. While complete quantitative accord between these calculated talues and available experimental data is lacking, nonetheless numerical accord is better than might be expected and, more importantly, parallel numerical trends are observed between experimental and calculated vnlues. WITHIN the past decade the enthalpy of formation of CaMg, has been determined a) from measurement of magnesium vapor pressures over binary Ca-Mg alloys,&apos; b) by solution calorimetry with liquid tin as the solvent,&apos; c) from measurement of hydrogen vapor pressures over ternary alloys of calcium, magnesium, and hydrogen,3 and d) by direct reaction alorimetr. The value from tin solution calorimetry is the most precise and is probably the most reliable, and this value is within the quoted uncertainties of the other three experimental results. The overall agreement among the four independent investigations is quite good, particularly so when the diversity of techniques is noted. On the basis of this agreement, CaMgz was chosen as a test material to evaluate the operation of a newly constructed apparatus for the determination of enthalpies of formation of intermetallic phases by acid solution calorimetry. This was believed to be a severe test because of the high chemical reactivity of both calcium and magnesium which reactivity presumably accounts for the fact that an early determination5 of the enthalpies of formation of Ca-Mg alloys by acid solution calorimetry yielded values significantly more negative than the four recent determinations. EXPERIMENTAL APPARATUS AND MATERIALS Experimental Apparatus. The enthalpy of formation of CaMg, was determined by measuring the difference between the heat evolved when dissolving the metallic compound and the heat evolved when dissolving equivalent amounts of unreacted metallic elements in hydro- chloric acid. This was done differentially with an apparatus consisting of twin calorimeters which were constructed to be as nearly identical as possible. The advantage of differential calorimetry is that systematic errors arising from the individual calorimeter design tend to cancel. A schematic representation of the apparatus is shown in Fig. 1. A dead air space around both calorimeters was provided by a large, thermally insulated jacket. Each calorimeter consisted of a 2-liter Dewar flask which was completely enclosed in a copper container. Each Dewar contained 1600 g of 2.5hr HCl to act as the solvent, and thermal effects resulting from solvent evaporation were minimized by covering the acid with 50 g of mineral oil. There was no detectable reaction between the acid and the mineral oil. Equivalent amounts of mechanical energy were added to the calorimeters through twin stirring rods which were driven at the same rpm by a single motor with the intent of the stirring being to maintain thermal equilibrium throughout the solvent. To calibrate the heat capacities of the calorimeters, known amounts of electrical energy could be added by passing measured voltages and currents for known times through submerged heaters, approximately 20 ohms, which were wound noninductively from Manganin wire. A 6-v storage battery was used as a power source, and a dummy heater was used as an exercise circuit to allow the battery to stabilize at a constant electromotive force before energizing one or the other of the calorimetric heaters. A type K-2 potentiometer was used to measure the potential drop across an energized heater while the current was determined from the potential drop across an external standard resistor. Times of energization were measured with an electric timer, and the electrical energy supplied to a heater

Jan 1, 1969

By Alan Zeni

Blind shaft drilling equipment has not changed substantially since the 1970s. Since it resides in a niche market between conventional shaft sinking and raise boring, the relatively small demand has resulted in some stagnation of development. In the 1990s the technology found a larger foothold in foundation and deep piling work for civil construction. WIRTH GmbH from Erkelenz, Germany has been servicing this market for many years with pile top drilling rigs and tools. Frontier-Kemper Constructors, Inc. recently entered into an agreement with WIRTH to develop a new generation of large diameter blind drilling equipment more specifically aimed at mining needs. The, recently completed, DHI-240 is the first rig to apply the most recent technology. This machine made its commercial debut in the fall of 2008. A description of the technology and a short case study of the first project will be described

By C. Pelley, S. Kelebek, S. Gregersen, P. Katsabanis

A series of small scale tests have been conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the physical properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Young’s modulus, Poisson’s ratio, P-wave, S-wave velocity, point load strength index and grinding work index were evaluated for samples without any blasting load and for samples which had received a variety of blast loads, such as a simple side impact from a detonating cord, or combined impacts without any delays and with very short delays. The investigation covered two types of rock, granodiorite and limestone. The effect of blasting load on the physical and rock mechanics parameters of the rock was clearly shown and damage was quantified and related to loading. However the work index did not show significant differences between blasted and not blasted samples, probably due to the relatively low level of impact. Numerical modelling using the AutodynTM code was used to demonstrate damage development in the various configurations tested.

Jan 1, 2003

By Ann Barron

For millions of people, cold weather is a fact of line – and one that can make a major challenge out of just getting to work. But for those working in the blasting industry, a number of obstacles are created when old man winter blows in. In addition to the obvious concerns regarding personal protection, Mother Nature can throw some very nasty weather at the blasting crew trying to travel with explosives products from the magazine site to the job site. As such, divers need to be familiar with cold, ice, and snow driving conditions both on and off the blast site. It’s critical to know what to expect before you leave. Keep informed of the latest weather and road conditions as they change often; it will help you make the right choice in clothing and driving habits. Remember bridges and overpasses will freeze first even in temperatures above or near the freezing mark due to the effects of wind chill. Plan to take extra time to and from the job site.

Jan 1, 2004

By Steven J. Page, John A. Organiscak

Laboratory crushing experiments were conducted on a range of low- to high-volatile bituminous coals to investigate the various factors influencing airborne respirable dust (ARD) generation. This research was conducted to identify the principles of ARD liberation from the coal product. Five U.S. bituminous coals were uniformly prepared and processed through a double roll crusher located in a low-velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, coal grind ability, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific ARD generated. The results of this investigation indicate that a combination of several factors are associated with ARD generation. One factor is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. Another key factor is the effect of air dry loss(ADL) moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The effect of these factors is that different percentages of <10-m coal particles are dispersed as ARD. A discussion of electrostatic field principles, coal ADL, and its effect on ARD generation is presented.

Jan 10, 1998

By T. Clarkin

This paper presents a hydrologic closure design concept to minimize the risk of water discharges from closed mine tailings facilities. It evaluates the applicability of U.S. Nuclear Regulatory Commission guidelines to develop acceptable designs for the closure of tailings facilities that have a calculated adequate surcharge capacity for environmental protection and an emergency spillway for dam safety. The guidelines provide a basis to estimate an acceptable surcharge capacity of a Probable Maximum Flood series for storage of surface runoff. To be conservative and for redundancy with respect to dam safety, an emergency spillway is provided to pass the Probable Maximum Flood. Depending on the annual water balance, the surcharge capacity may be used by surface runoff and minor amounts of sediment that accumulates in the impoundment from year to year. The emergency spillway crest is then set at this level or above the surcharge capacity, whichever is higher. An example is given of the active Red Dog Mine tailings facility in Alaska where this method was used for the preliminary design of the tailings main dam at its ultimate closure configuration.

Jan 1, 2012

By J. W. Hickman, E. A. Gulbransen

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400&apos; to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400&apos; and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By E. A. Gulbransen, J. W. Hickman

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400&apos; to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400&apos; and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By Dan Witkowsky

Beginning on June 11, 2007, as many as 36, kindergarten-to-grade-12 (K-12) teachers will participate in a program designed to educate them all about the mining industry. The 39th Annual A Total Concept of the Mining Industry – All About Mining, will be conducted by the Colorado Mining Association Education Foundation, Inc. (CMAEF) and the Office of Special Programs and Continuing Education (SPACE) at the Colorado School of Mines. This flagship program includes four intensive weeks at the Colorado School of Mines. During that time, more than 75 volunteer lecturers will “educate the educators” about mining and its importance to the United States and the world. During the learning process associated with obtaining a basic understanding of mining and all its aspects, the teachers will be hosted by hundreds of other industry professionals at 10 Colorado mining operations. Also visited will be a government earthquake center, a museum of mining and industry, an earth mechanics laboratory, a metallurgical research center, a metallurgical concentrator, an electric power plant and a steel mill. Questions before, during and after visits will be answered by another select group of volunteers who will travel with the teachers to the various sites.

Jan 1, 2007

By R. Kus´

The paper presents the comments on the advantages of implementing an integrated system of managing mining exploitation in hard coal mines, as well as the comprehensive integration of information on the process of deposit exploitation with economic data, so as to achieve an optimum technical and economic effects. The principles of constructing the production management system have been presented, thanks to which the management boards are provided with reliable technical and economic information on a mining company via information technology. The strategic direction of a company’s operation may currently be verified according to the external conditions that change over time (the information on the deposit, force majeure events, changing expectations of customers, etc.).

Jan 1, 2003

By Richard S. Gaps

The Derby and Alexander Claim, located within the Tunnel Ridge Wilderness Study Area (WSA), has placer gold resources. No lode deposits are known within the area, but lode gold deposits are found within 1 1/2 mi of the WSA. In additon, rock units which contain lode gold deposits north of the WSA are found within the northern portion of the study area. INTRODUCTION The Tunnel Ridge Wilderness Study Area (WSA), CA-030-402, encompasses 4,623 acres of BLM administered public land in Trinity County, California, about 35 mi west-northwest of Redding (fig. 1). Major access to the Tunnel Ridge vicinity is by U.S. Highway 299. Ac-cess to the WSA boundary is by a secondary paved road from Junction City and several light duty dirt and gravel roads (fig. 2). The WSA is on the southwest slope of Weaver Bally Mountain. The topography is rugged with moderate to steep slopes; elevations range from about 1,600 ft to 5,900 ft.

Jan 1, 1983