Search Documents

By Zhitao Ma

The Cast-in-place Concrete thin-wall Pipe pile, referred to as PCC pile, is a new kind of pile for soft ground improvement. In this paper, firstly, the general introductions of the new pile technique, mainly including the technique principle, the structure of pile-driving machine, and the technological process were given, then based on the results of in-situ static lateral loading test, the pile lateral capacity, the relationship of load-deflection of pile at the ground surface, the lateral deflections versus depth and the soil reaction along the pile shaft were analyzed.

Jan 1, 2006

By E. S. Greiner

THE hot working of chromium was first reported by Hunter and Jones; who used small pellets of the material obtained by the reduction of chromium chloride with sodium. Later, the working of chromium at 600° to 1100°C was reported by Marden and Rich,2 and at 1250°C by Kroll3 The hot rolled material3 had a Brinell hardness of about 150 (62.5 kg, 2.5 mm ball, 1 min) and was brittle at room temperature. Except for that associated with hardness indentations, no plastic flow in chromium at room temperature has been reported to the author's knowledge. Studies described here have shown slip markings in chromium after deformation at room temperature.

Jan 1, 1951

By M. Prud’Homme

Potash is an important natural mineral used largely as a fertilizer in the production of food and fiber. About 93 percent of all potash consumed globally is used in agriculture as fertilizer. The balance is used to manufacture potassium chemicals. Most potash is extracted by conventional underground mining methods. Solution mining is used when underground deposits are irregular and very deep. The other main production method involves the evaporation of brines in shallow salt lakes, followed by the harvesting of potassium minerals.

Jan 1, 2005

The Mining Foundation of the Southwest will host its 24th Annual American Mining Hall of Fame Awards Banquet at the Tucson El Conquistador Golf & Tennis Resort in Tucson, AZ on Saturday, Dec. 9. The Mining Foundation of the Southwest is a non-profit organization whose objectives are public education about the mineral industries. It also recognizes outstanding accomplishments in and contributions to the fields of fuel and mineral resources.

Jan 1, 2006

The Dynamics and Thermodynamics of Absorbing Lithium of Ion Sieve Preparing Pollymetallic Nodules

Sep 13, 2010

By Carl Hendricks, Malcolm Scoble

There currently exists no viable means of obtaining continuous feedback on blast efficiency. This paper describes the adaptation of a loading shovel to serve as a diagnostic tool to evaluate the success of ground preparation. Work undertaken in a large western Canadian open pit involved microprocessor-based instrumentation for the performance monitoring of an electric mining shovel. The monitored shovel responses proved to be reliable indicators of variations in muckpile diggability. This approach is considered to provide a very comprehensive survey of post blast conditions since such a shovel interacts which every cubic yard of a blast.

Jan 1, 1990

By Paul D. Tomlingson

World class performance is the ultimate objective of many maintenance organizations. It marks the organization as a leader in its industry and sets it apart as the ultimate achiever. But what is a “world class” standard and how can it be achieved? Is there a yardstick by which an industrial organization can measure the relative performance of its maintenance activity and compare it with performance levels that universally identify “world class” status? Are there financial formulas, achievements, evaluation techniques or indices that provide this yardstick?

Jan 1, 2006

By Bill Starke

The acceptance of AugerCast piles in Canada has been limited. Many engineers are apprehensive about the quality of the piles produced by this method. However, advances in the sensing instruments and computer technology can now provide satisfactory levels of quality assurance. Post construction tests such as the sonic echo method can give an indication of pile shaft integrity. Computerized monitoring of the pile installation process is an immediate and more positive method of quality assurance. The computer continuously measures and records the parameters which indicate the quality of the pile. If these parameters do not indicate a satisfactory pile, it is replaced before the concrete hardens. Computerized monitoring of the installation process is another tool available to the engineer. The data from this system analyzed with soil borings, site inspections, and possibly sonic tests can provide the engineer with enough information for pile certification.

Jan 1, 1997

By G. Kipouros, M. Dadvand, A. Dadvand

"A novel methodology was developed to obtain a 3D porous layer with a high aspect ratio of porosity on a titanium electrode. The porous structure allowed more active material such as hydrous ruthenium oxide to be accommodated during the fabrication of the supercapacitor, resulting in an exceptionally high capacitance per surface area. The electrode demonstrated a remarkably high capacitance of 4,800 mF/cm2. The porous layer was composed of functionalized nanoparticles of TiO2 organized in a perfect 3D hexagonal close-packed array that resulted in a highly porous 3D structure. The layer was used as a template to electrolessly deposit a thin layer of silver prior to the electrodeposition of active material. KEYWORDS Capacitance, Porous, Ruthenium, Silver, Supercapacitor, Titanium RÉSUMÉ Une méthodologie innovante a été mise au point afin d’obtenir une couche poreuse tridimensionnelle (3D) affichant un rapport d’aspect élevé en termes de porosité sur une électrode en titane. La structure poreuse permet d’utiliser une matière plus active telle que l’oxyde de ruthénium hydraté durant la fabrication du supercondensateur, ce qui se traduit par une capacité exceptionnellement élevée par surface active. L’électrode affichait une capacité remarquablement élevée de 4 800 mF/cm2. La couche poreuse était composée de nanoparticules fonctionnalisées de dioxyde de titane (TiO2) organisées dans un arrangement regroupé parfaitement hexagonal en 3D, qui a engendré une structure en 3D hautement poreuse. Cette couche a servi de modèle pour le dépôt autocatalytique d’une fine couche d’argent avant l’électrodéposition de la matière active. MOTS CLÉS argent, capacité, poreux, ruthénium, supercondensateur, titaneINTRODUCTION There is a growing demand for integrating compact energy storage elements into electronic circuits due to the miniaturization of electronic circuits, sensors, and actuators, and the increasing importance of portable and wear-able devices incorporating more advanced electronic technologies that operate in controlled or uncontrolled environments to gather, process, store, and communicate information (Deng, Ji, Chen, & Banks, 2011; Beidaghi & Wang, 2012; Chen, Ramachandran, Mani, & Saraswathi, 2014). The manufacturing of compact energy storage elements needs to be compatible with the electronic circuit microfabrication processes. Recently, interest in integrating miniaturized supercapacitors into electronic circuits has increased due to their high charge–discharge rate and long operating life; however, ultra-high power miniaturized supercapacitors suffer from low energy density, hence requiring significant enhancement in their energy density for various applications (Deng et al., 2011; Beidaghi & Wang, 2012; Chen et al., 2014)."

Jan 1, 2019

Determination of Porosity and its Influence on Specific Surface

Sep 13, 2010

By Ron Beeslaar, Tony Rorke

The Professional Blast Manager is a blast design tool that has been developed in South Africa. It is aimed at mining and civil engineen, blasting contractors and mine planning engineers. The code can be used as a stand-alone package or be combined Into complex mine information systems.

Jan 1, 1998

By E. D. Gardner

"Trolley lines used in connection with electric haulage in mines are a source of danger and many lives have been lost by men accidentally coming in contact with the wires. Usually the wires in metal mines are sufficiently guarded to prevent men from touching them with their person or by pieces of steel which they may be carrying or their shoulders, while walking along the level. However, it is difficult to guard effectively the wires at loading chutes along the haulage ways and in spite of safe guards, chute tappers have been electrocuted through loading bars accidentally touching the trolley line.To overcome this danger the Calumet & Arizona Mining Co., at Lowell, Arizona formely used a hinged V-shaped trough made of 1-inch by 6-inch lumber, that was dropped over the wire in front of the chute, when the cars were being loaded. This arrangement interfered with the easy operation of the chute, and a cut-out device for the trolley line was devised by W. R. Gibson, chief electrician for the company. This cut-out is efficient easily constructed and roes not interfere with the operations at the chutes or with the motors operating on the same level.When the cut-out is open the electric current is carried past the gap by an insulated wire on the opposite side of the drift. A hinged board drops down over the ends of the trolley guard when the slide is open and Prevents anything touching the live wires. About ninety of these cut-outs are now in use in the mine,The levels under the scopes are timbered with drift sets placed 5 feet apart, and the loading chutes take up the space between two sets. All trolley wires in. the company's mines are carried 6 feet above the rails and guarded by two 1/2 by 6-inch boards placed on either side of the wire."

May 1, 1921

By J. H. Zietsman

Ilmenite smelting furnaces must be operated with a freeze lining of frozen slag to protect sidewall refractories from chemical attack by liquid slag. The process has two main control objectives: Firstly the slag TiO2 content must be controlled according to specification, and secondly a safe freeze lining thickness must be maintained. This text only concerns itself with the second objective. Freeze lining thickness cannot be measured directly due to conditions inside the furnace. It is therefore inferred from signals of thermocouples installed into the furnace sidewall. These signals are used as the 'controlled variables' in the freeze lining thickness control loop. The dynamic characteristics of these signals are the focus of this text. During this study a model of the process was constructed to study interactions between the slag bath and the freeze lining. This model was used to conduct simulation-type experiments to study the influence of various parameters (temperature, slag composition, ilmenite feed rate, reductant feed rate, power input, etc.) on the slag bath, freeze lining, metal bath, furnace wall and other parts of the process. In the case of the furnace wall, the modelling results were first plotted in the form of time-dependent isotherms. The dynamic thermal behavior of the furnace wall became evident from these results. To illustrate the dynamics of sidewall thermocouple signals, the results were also plotted as time lags between events occurring in the slag bath, and the time when a thermocouple registered a temperature change. The events studied included sudden changes in slag bath state (composition and temperature), changes in operating setpoints (ilmenite feed rate, reductant feed rate, power input), and operational errors (complete loss of reductant or of all feed). All of the result sets showed significant lags between occurrences in the slag bath and temperature changes in the refractory wall. The delays are such that it appears impractical to rely on sidewall thermocouple signals for warning of impending damage to the refractory wall, or for purposes of actively controlling freeze lining thickness. Some measures are suggested to improve the usefulness of these signals during furnace operation.

Jan 1, 2005

By Thomas L. Watson

A part of the field-seasons of 1900, 1901 and 1902 mas devoted by the writer to a study of the manganese ore-deposits of Georgia. A report embodying the results of this study is rapidly nearing completion, and when finished it will be published as a bulletin of the Geological Survey of Georgia. I believe, however, the importance of these deposits warrants a separate and earlier publication than that made possible by the Survey, in which the more important results of the study are briefly set forth. It is principally for this reason that the present paper has been prepared. Previous Work.—Some of the more important deposits of manganese occurring in the Paleozoic area of Georgia were studied to some extent previous to 1890 by Dr. Penrose;t and again in the early nineties by former State Geologist, J. W. Spencer. In a recent paper published in the Transactions, on the " Geological Relations of the Iron-Ores in the Cartersville District, Georgia," Dr. Hayes briefly mentions the manganeseores of the same district. Distribution of the Manganese-Ores.—Georgia is divisible into three geologically-distinct areas which, named in order from southeast to northwest, are (a), the Coastal Plain; (b), the Crys-

Jan 1, 1904

By Y. P. Chugh

A novel dry and wet air dust filter concept was conceived and demonstrated successfully at two mines. A steel-wool and a fiberglass filter, suitable for underground use were identified through laboratory testing and demonstrated in the mine. The steel wool filter was operated with and without water sprays while the fiberglass filter was only operated in the dry mode. The dry steel wool filter provided a dust capture of 37% at a negligible pressure drop. When fine misting water sprays were used on the steel wool filter, the dust capture increased to 51% again with a negligible pressure drop. The filter screen also remained clean and no change in air flow characteristics was observed as a function of time. The dry fiberglass filter however did not perform as well achieving only 11% dust capture while introducing a significant resistance to air flow. This technology is seen to have several applications in underground coal mines.

Jan 1, 2009

By Kostas Fytas

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (ex. pyrite) contained in rock are exposed to air and water and subsequently oxidize to produce low pH water. This acid effluent has the potential to mobilize any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pyrite is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidizes a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

May 1, 2001

Quickly and cheaply consolidate underground slimes to facilitate their use as backfill and permit their easy handling for other reasons. Approach: The slurry containing slimes is pumped into active stopes and electrokinetically dewatered to provide consolidated back fill. How It Works: To densify slimes electro-kinetically two electrodes are placed in the material to be dewatered and densified. Typically, the electrodes are pieces of wire mesh fencing. One is placed on the bottom, and the other is suspended in the slurry near the surface. Figure 1 is a simplified section of a test. A d-c voltage of 100 to 400 volts is applied across the slurry. This causes the solid particles which are in suspension in the water (usually these are negatively charged) to migrate toward the anode; simultaneously, the water moves toward the cathode. Water immediately adjacent to the negatively charged solid particle surfaces contains an excess of dissolved positive ions. When these ions are attracted to the electrode and move towards it, they also exert

Jan 1, 1976

By P. J. Cook

Comminution is one of the fundamentals of mineral processing, requiring large expenditures to be made on capital equipment, installation, power and maintenance. The trend toward lower grades and higher operating costs, mean mining operations are becoming increasingly marginal. The challenge is to improve and more importantly, utilise crushing and milling technologies that provide for reduced capital and operating costs whilst providing increased unit efficiencies. The Svedala Barmac Autogenous Crushing Mill presents such an opportunity by providing many of the cost savings and production increases required by its ability to produce a finer mill feed size and realise reduced energy consumption. This paper briefly describes the operation of the Svedala Barmac Autogenous Crushing Mill and reviews its benefits towards improving the efficiency of crushing and milling operations.

Jan 1, 1999

By J. Andres, M. Cross

"Freeport-McMoRan’s Sierrita operations has two natural gas-fired molybdenum roasters for converting molybdenum disulfide into molybdenum trioxide. When these roasters were compared to other similar units within the company during a benchmarking exercise, it showed that increased throughput from the roaster units at Sierrita was possible. A team of site metallurgists, technical experts from other sites, and engineers from the Climax Technology Center was formed to study the potential in more detail. The team investigated many parameters in the roaster, including temperature profiles, roaster chemistry profiles, rabble and drop hole patterns, and operational strategies. The results of these studies and the associated throughput improvements are described in this paper. INTRODUCTION Molybdenum, a vital component for the steel industry, is typically found in nature as molybdenum disulfide (MoS2). MoS2 is typically recovered via flotation processes and is purified through leaching processes. While molybdenum disulfide is a commercial product, it is not the form of molybdenum that the steel industry requires. They require molybdenum in the form of molybdenum trioxide, MoO3. There are multiple ways to refine molybdenum disulfide into molybdenum trioxide. The primary method is the oxidation of molybdenum disulfide in a multiple hearth roaster. The chemistry of converting molybdenum disulfide to molybdenum trioxide is very favorable at increased temperatures, oxidizing the molybdenum through a range of exothermic reactions to ultimately produce MoO3. The chemical reactions that occur in molydenum roasting occur in three zones. These three zones correspond with four different reactions."

Jan 1, 2015

By Jozef F. Zurawski

Increasingly new interceptors or new Combined Sewer Overflow (CSO) projects require connections to existing tunnels. More often than not, the existing facilities are old, in poor or questionable conditions, without proper construction records or as-built drawings. Many cannot be easily inspected unless major construction effort provides flow by-pass for safe access. This paper provides general guidelines on how to approach the problem of assessing the condition of old tunnels, how to plan and design the connection with limited physical assessment, how to develop the scope of work for the bid documents and how to provide geotechnical guidelines and designs for the bid documents.

Jan 1, 2008