Search Documents

By Paul M. Wiltcher

This paper discusses how benefits in engineering design can be achieved from combining existing GRP concrete design guidelines with carbon steel design codes primarily made possible due to the increase in the constitutive properties of modern composite rebar or GRP. It also examines the technical and practical considerations necessary to both construct and ensure the integrity of composite rebar during transportation and handling on site and the measures taken by Franki-Cementation Joint Venture to ensure the safe deployment of the GRP in the workplace on the Noord/Zuidlijn Project in Amsterdam between 2003 and 2006.

Jan 1, 2006

Investigation of the Classification Operation in a Coal Pulverising Vertical Spindle Mill Coal pulverisation in power plants is a major electrical energy consumer. In 2006 more than 41 per cent of world electricity generation was from coal where pulverisers use 0.5 to 1 per cent of gross generation. Therefore, pulverisers are an important target for optimisation not only for reducing costs of power generation but also for reduction of greenhouse gas emissions. A better understanding of the operation of pulverisers is an essential requirement for their optimisation. However, little information is available, other than operating experience, on the performance of pulverisers and how these react to changes in operational variables. This study investigates the effect of changes in coal and airflow feed rates on the classification performance that occurs in an industrial scale ball-and-race vertical spindle mill in which the pulverisation and classification processes are linked together due to the separator classifier being an integral component within the pulveriser. In order to decouple the breakage and classification processes, samples were cut from upward flowing streams through sampling ports drilled on the pulveriser body at different locations. Specific sampling tools were developed. Samples collected from the pulveriser were size and density fractioned to distinguish the differences in behaviour of the components, namely coal and mineral matter. The coal flow rates on dry basis within the mill and around the separator classifier were calculated by mass balancing the multi-component data. The difference in classification behaviour of components during pneumatic transport was confirmed. The response of the circulating load in the mill (~600 to ~1100 per cent) as well as the dependency of fineness of the streams to the operating variables was demonstrated. The approach taken in this study has proved that development of a classification model for a vertical spindle mill pulverising non-homogeneous materials, eg coal, requires treating these materials as multi-component/composite substances.

Sep 13, 2010

By U. Singh, E. T. Brown, J. Coxon

The rapid fracturing and deformation that occurs around excavations during rock bursts demand that support and reinforcement systems have both deformability and damping capabilities. The energy demand and supply approach currently used in design is considered to be too simplified to represent adequately the rock burst process and the support and reinforcement system requirements. Momentum change may be a necessary second criterion for the analysis of dynamic loading situations. At the St Ives Gold Mining Company, DE plates made from conveyor belt rubber, and dynamic cables with sliding anchors have been developed and used to improve the dynamic performance of support and reinforcement systems. La fracturation rapide et la déformation qui se produisent autour des excavations lors de coups de terrain demandent que les systèmes d’armature et de support soient déformables et aient une capacité d’amortissement. L’approche basée sur l’énergie actuellement utilisée pour la conception est considérée être trop simplificatrice pour représenter adéquatement les coups de terrain et les paramètres de conception des systèmes d’armature et de support requis. Le changement de quantité de mouvement pourrait être un second critère nécessaire pour l’analyse des cas de charge dynamnique. St Ives Gold Mining Company a développé et utilisé des plaques « DE » constituées de caoutchouc de courroie de convoyeur et des câbles dynamiques avec ancrage coulissant afin d’améliorer la performance dynamique des systèmes d’armature et de support. Die ploetzliche Rissbildung und Verformung, die sich in Baugruben waehrend eines Felseinbruchs ereignet, verlangt Stuetz- und Verstaerkungssysteme, welche verformbare und mildernde Eigenschaften aufweisen. Die derzeitlich gebraeuchliche Methode den Entwurf auf den Energiebedarf und dessen Abdeckung zu basieren, wird als eine unannehmbare Vereinfachung betrachtet, da sie den Felseinbruch und die benoetigten Unterstuetzungs– und Verstaerkungssysteme unzulaenglich darstellt. Die Aenderung der Umstaende kann einen zweiten Ansatz fuer die Analyse der Lastsituation erforderlich machen. Die St.Ives Gold Mining Company hat DE Platten aus Foerderband-Gummi und elastischen Kabeln mit verschiebbaren Verankerung entwickelt und dazu verwendet, die dynamische Kapazitaet der Unterstuetzungs- und Verstaerkungssysteme zu verbessern.

Jan 1, 2003

By Panfeng Gou

In order to solve the problems of supporting the roof of the gateroads affected by a fault, the movement characteristics of roof strata must be fully understood. In this paper, a plane stress physical simulation model was constructed to study roof strata displacement and deformation of gateroads driven in the hanging wall of the fault after the coals in the footwall were extracted. The results indicated that, due to the effect of fault, vertical cracks, orienting parallel to the dip of the fault, occurred in the horizontal direction of the model within the areas affected by the fault. The roof strata are discontinuous. On the other hand, non-uniform subsidence of roof strata occurred due to the bedding plane separation in the vertical direction. Roof strata, especially the lower roof strata, dip toward the fault. Failure of the surrounding strata is not symmetrical with the roof and floor close to the fault being deformed severely. In the selection of type of supports for the gateroads, the U-shaped steel supports are superior to roof bolting.

Jan 1, 2006

By R C. A Minnitt

This paper illustrates the use of variography and moving average plots as an aid to analysing variations in the process that can be used to direct the improvement efforts. The hydrometallurgical processes used in manganese metal production consist of sequential unit operations that include milling and reduction of manganese ores. Leaching of the reduced ore, is followed by solid-liquid separation, residue disposal, solution purification and electrowinning of manganese metal completes the process. The nearly 250 integrated process control loops rely on reports of pH, flow pressure, level, temperature and chemical analyses. Metallurgical accounting, reconciliation and process control is achieved through monitoring of the chemical and mass balances within the manganese reduction plant, requiring approximately 50 000 analyses of solids, powders and liquids each month. The largest numbers of samples are taken in the cell house. Changes and variations monitored by sample statistics ensure that the manganese products comply with predetermined specification limits. Optimising the information-value of the approximately 50 000 samples in the manganese plant is carried out in tandem with ongoing process optimisation. Variographic analysis of daily sampling data suggests that the cyclical behaviour evident in the moving average plots is only a reflection of random residual variability and not a reflection of true underlying variability related to cyclical phenomena. Low resolution in the variogram of daily sampling data masks the short-range variability that emerges when hourly data are analysed. Hourly samples collected over a 39-day period (giving 941 sample data), helped identify short-range cycles in the process. The relative distribution of variability for daily sample intervals, indicate that 57 per cent arises from V[0], 18 per cent from V[process] and 16 per cent from random residual variation. V[0] includes all the uncontrolled sampling error arising from a poor sampling protocol, the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. This confirms the suspicions regarding the suboptimality of the sampling protocol and the way it is implemented. The absence of long-term trends in the leach suggests that short-term variation (less than one day) dominates the process. While the control charts indicate that the overall processes are maintained above the lower specification limits and the target values, there is nevertheless a considerable amount of variability in the system that overhangs the processes and threatens to impact them negatively. Although the variability in the leach is above the prescribed limits, the volatility is a matter of concern because it seems to be uncontrolled. The comparison of the various sources of variability in data collected on an hourly basis suggests that the short-term random variability (V[0]) accounts for almost 50 per cent of the variability in the process. The main source of this variability is due to errors in the sampling protocol and is probably related to the size of the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. Remediation of FE and GSE will probably lead to a reduction in V[0], whereas V[process] could be mitigated by reducing the biases associated with DE and EE in particular.

Jan 1, 2008

By Neil E. Ryan

Because of their chemical reactivity and affinity for oxygen, rare-earth elements are difficult to extract, and due to their close chemical similarity, it is an exacting task to separate one from the other. Nevertheless, these same characteristics can be used to benefit other metals by enhancing their resistance to high-temperture oxidation/corrosion and by inhibiting their corrosion in aqueous environments. This paper gives an overview of the use of rare-earths: [a] as alloy additions, [b] in coatings, and [c] when added to hostile environments, to retard rates of high- temperature oxidation and inhibit aqueous corrosion.

Jan 1, 1992

By David J. Mack, Dennis R. O’Boyle

The mechanical properties of three polycrystalline intermediale Phases that have the y bvass structure were measured in compression between 400° and 900°K. At the lower testing temperatures— termed Region I— no plaslic deformalion occurred prior to brittle fracture. A1 higher temperatuves— lermed Region III—the three phases deformted plaslically for all strain rules from 1.5 to 36.0 x 10-4 sec-1. The homologous temperature for the inilialion of plaslic flow increased in the same order as tile atomic size difference between atoms in each plmse (0.50Tmp for y AgZn, 0.62Tmp for y CuZn, and 0.76 Tmp for y CuCd). The increased flow resistance oj. y CuCd above 0.50Tmp is explaitzed in terms of the more random arrangement of copper and cadmiwn atoms on the laltice sites of&apos; the y bvass slrilctlire. Plaslic deformation of the three intevmiediate phases in the smooth plaslic flow region appears to be controlled by oacancy-induced dislocation climb. RESULTS are reported in this paper on the mechanical properties of three binary intermediate phases having the complex cubic y brass structure (D82, 143m) containing fifty-two atoms in the unit cell. The structure of the prototype y brass phase, y CuZn, was first analyzed by Bradley and Thewlis&apos; based on the X-ray work of Westgren and Phragmen.2 The y brass structure can be visualized as an arrangement of twenty-seven body centered cubes (3 by 3 by 3) into a unit cell containing fifty-four atoms. From this cell the center atom and the four corner atoms are removed and the remaining fifty-two atoms are slightly displaced, resulting in the y brass structure. Approximately thirty-five binary intermediate phases that have an electron to atom ratio of 21:13 have been reported to form the y brass structure. The three y brass intermediate phases selected for this study are formed from elements in groups IB and IIB of the first and second long period. Each compound exists over a composition range that includes the stoi-chiometric composition A5BB (Cu5Zn8, Ag5Zn8, Cu5Cd8). y CuZn (a0 = 9.944A) has solubility limits extending from 57 to 67 at. pct Zn at 500°C apd melts peritecti-cally at 834°C; y AgZn (a0 = 9.326A) has a solubility range from 58 to 63 at. pct Za and melts peritectically at 661°C. y CuCd (a, = 9.596A) melts congruently at 563°C and has a maximum range of solubility extending from 58 to 64 at. pct Cd. In order to minimize coring and microporosity during solidification, the composi- tion of the compounds that form peritectically (y CuZn and y AgZn) was chosen so that the temperature difference between the liquidus and the solidus is only a few degrees centigrade. In selecting y brass compounds for this study, phases were avoided that contained a transition element or that had an electron to atom ratio greater than 1.70. Hume-Rothery et a1.3 has observed that, when the electron to atom ratio of y brass intermediate phases exceeds 1.70, atoms begin to drop out of the unit cell to maintain a constant electron to unit cell ratio. EXPERIMENTAL PROCEDURE Each of the three intermediate phases was prepared from elements having a purity >99.999 pct. Only trace quantities of impurities (<0.0001 pct) were detected by spectrographic analysis of the four elements. A master alloy of each compound weighing approximately 130 g was prepared by melting the elements in evacuated sealed quartz tubes heated in an electric furnace. Specimens having the desired diameter for the mechanical property measurements were obtained by remelting the master alloy in a Vycor tube under argon and drawing specimens from the melt into 4-mm-diam quartz tubes. To obtain a smooth surface on specimens drawn from the melt, the inside of the quartz tube was coated with a thin layer of graphite formed by thermally decompositing acetone. All specimens were imbedded in sealing wax and cut to the proper length with a diamond-impregnated cut-off wheel. The individual specimens (4 mm diam by 8 mm long) were then sealed in evacuated Pyrex tubes and homogenized at 500°C for 72 hr. Chemical composition, variations over the length of the rod (10 cm long) were generally less than 0.2 pct and the analyzed composition differed from the desired composition by less than 0.5 pct.4 Metallographic evaluation of the specimens after homogenization showed no evidence of a second phase in any of the compounds. The average grain size of the specimens after homogenization was 1 to 2 mm. All mechanical property measurements were carried out in an argon atmosphere using a compression apparatus described previously.5 Prior to applying the load to the specimen, the test apparatus was evacuated, back-filled with argon, and heated to the test temperature for 20 min to establish thermal equilibrium. EXPERIMENTAL RESULTS Mechanical properties measured as a function of temperature and strain rate for each of the three y brass phases were similar. From room temperature to the ductile-to-brittle transition temperature, only elastic deformation was observed prior to fracture.

Jan 1, 1968

By Winton Gale, David Oyler, Jinsheng Chen, Christopher Mark

The National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia have collaborated to conduct an extensive study of roof bolt strata interaction at the Emerald mine in Southwestern Pennsylvania. The primary goal of the project was to obtain detailed data on the interaction between the mine roof and the support elements for use in modeling studies. The study site was a longwall tailgate subjected to high horizontal stress. Three arrays of instruments were installed at the site, one in the tailgate entry and two in an adjacent crosscut. Pumpable concrete cribs were present in the tailgate array, and cable bolts were installed in one of the crosscut arrays. The instruments included mechanical and sonic extensometers for measuring roof movement, instrumented roof bolts, and three-dimensional roof stress cells. The study was ultimately successful in determining the magnitude of the horizontal stress concentration, the height of roof failure and the roof failure sequence, and the loading history of the primary roof supports.

Python Underground Processing Plant Critical Design The use of continuous gravity recovery in combination with a controlled breakage fine crushing and screening system followed by flash flotation has been incorporated into the Python processing plant. This provides miners with a flexible, robust, low cost, low energy pre-concentration process for the recovery of gold and/or heavy minerals. The Python plant incorporates fine crushing utilizing either High Pressure Grinding Rolls or Vertical Shaft Impactors in combination with the InLine Pressure Jig and Flash Flotation to continuously liberate and recover the valuable minerals. The use of these technologies has enabled a narrow, transportable pre-concentration plant to be produced which can easily be installed and operated in underground drifts and tunnels.

Sep 13, 2010

By Ertugrul Alp

Alp & Associates - Who We Are ?? Canadian consulting company (1999-?) ?? Principal Consultant: Dr. Ertugrul Alp, P.Eng. ?? Over twenty-five years experience serving the chemical, mining, pulp & paper, energy, steel, and transportation industries, and government clients. ?? Ph.D. in Mechanical Engineering, University of Waterloo ?? Experience: ?? Westinghouse Canada, Atomic Power Division, Manager, Analysis and Modelling ?? Concord Environmental (later Bovar Environmental), Principal, Manager, Air Quality and Risk Assessment ?? Arthur D. Little, Associate Director, Safety & Risk Practice Leader in Canada ?? Member: NATO CCMS Pilot Project on Disaster Preparedness (1991-1993) ?? Chair: MIACC Risk Assessment Expert Committee, 1995-1999 ?? Member: MIACC Committees on Land Use Planning and Pipelines (1993-1998) ?? Member: CSA/Q850 Risk Management Standard Technical Committee ?? Member: CSA/Z1002 OHS Risk Assessment Standard Technical Committee ?? Member: CCPA/CSChE Process Safety Management Committee (1999-?) ?? Member: ISO-31000 Risk Management Standard Canadian Advisory Committee ?? Chair: CSChE Process Safety Management Committee (2005-2006) ?? Chair: CSChE Expert Committee on Risk Assessment (1999-2005) ?? CSChE 2007 Process Safety Management Award

May 1, 2008

By M. Hagfors

Underwater explosions have been used several decades for the determination energy content of explosives. It’s the only test method by which shock and gas heave energy values can be determined separately. The total energy is a sum of these two partial energies. This test method enables us to develop explosives for different purposes; the military high explosives should contain more shock energy whereas the gas heave energy is a very important feature for the blasting explosives. The method also enables us to observe the changes and to adjust the energy content of an explosive as a function of increments of one or more energetic component.

Jan 1, 2006

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Oct 1, 2004

The coal-bearing regions of Colorado cover approximately 29,600 square miles, which is 28.4 percent of the state&apos;s total area. The most important coal-bearing regions are located in the north western and west-central parts of Colorado. Coal resources vary from lignite to anthracite. More than 70 percent are bituminous; 23 percent subbituminous; 5 percent lignite; and less than 1 percent anthracite. The state&apos;s coal reserves total about 17.2 billion tons, 3.5 percent of national reserves. Approximately 8.8 million acres of coal rights in the state are owned by the Federal Government; on about 72percent of this land, the Federal Government controls both the coal and the surface rights. It is estimated that approximately 4.2 billion tons of coal reserves are under federal ownership in Colorado. Permitted acreage of mines in Colorado ranges from 40 to 13,114 acres. Differences in elevation create many climatic zones in Colorado. Local annual precipitation can average less than eight inches in some areas in extreme western Colorado to more than 30 inches in certain mountainous areas. Generally, precipitation rates are low at most mine sites, making revegetation difficult. Colorado gained primacy when its regulatory program was conditionally approved December 15,1980. The Abandoned Mine Land Program was approved June 11, 1982.

Jan 1, 1992

Neither the copper orebodies nor the zinc-lead-silver orebodies at Mount Isa were formed syntectonically as has been claimed for the last 20 and 10 years respectively. Both orebody types were cogenetic, coeval, and formed early during the sedimentation and diagenesis of the host formation. The copper orebodies are interpreted as having formed diagenetically at hand specimen scale, syngenetically at formation scale. The zinc-lead-silver orebodies are interpreted as having formed primarily by sedimentary means at both hand specimen and formation scales.

Jan 1, 2000

The Southwest Pacific is a region of active volcanism and geothermal systems. Only in New Zealand have the geothermal systems been exploited for electricity generation and industrial processing. At present, approximately 280 MWe of geothermal electricity is generated in New Zealand. A considerable amount of further exploration work is required before the total geothermal potential of the region can be assessed and before the significance of these resources can be judged against other local energy sources.

Jan 1, 1990

By Steven Dapp

A new hyperbolic model for generating P-Y curves is developed for use in lateral analyses of cemented soils (a ?C-F? soil with both cohesive intercept and friction angle), and includes degradation of the static loading soil response to model the effects of load cycling (repeated loading) with load cycle number. The p-y curves, for both static and cyclic loading, were derived from full-scale lateral test results conducted on a set of six drilled shafts in a loess deposit at the Kansas DOT test site. Values of the model parameters obtained from the load testing at this site are presented, as well as a discussion of the model parameters effect on the results such that the model may be rationally applied to other sites with C-F type soils. A step-by-step procedure is presented to illustrate the application of the model. Correlation of the model to the CPT cone tip resistance (qc) from CPT testing is made, as this was found to be the most reliable; However, the model is applicable to other methods, both in-situ and laboratory, of assessing the soils strength.

Jan 1, 2011

Commercialisation of outcomes from research projects is a process often poorly understood and managed, but has the potential to achieve significant benefits for the industry and community as a whole. JKTech Pty Ltd was established in 1986 to transfer viable research outcomes from the Julius Kruttschnitt Mineral Research Centre (JKMRC) at The University of Queensland, Australia. This paper describes successful and unsuccessful examples of commercialisation by JKTech over the years, and draws some conclusions as to the factors that contribute to success and failure in technology transfer.

Jan 1, 2012

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

Technologies are receiving a lot of &apos;press&apos; - and rightly so; as they are seen as the means for achieving quantum leaps in productivity and cost reductions. A point of concern for Caterpillar is that we do not believe there is enough understanding of the infrastructure needed to support some of the future technologies, as well there is not enough utilisation of the current systems.

Jan 1, 1997

By Z. G. Lin

In Xian, China, compaction by means of soil (or lime-soil) piles is one of the effective methods widely used for densifying loess and eliminating its collapsibility. However, as a result of groundwater table rising, it is no longer applicable in many areas. This paper is the summary of the first-time use in Xian of sand-gravel compaction piles aimed at densifying the miscellaneous fill (already partially under water) and saturated loess at a certain project site. In-situ tests, conducted before and after the treatment and including several kinds of penetration tests backed up and confirmed by a set of plate loading tests, yielded very satisfactory results, strongly testifying to the viability of the method.

Jan 1, 2010