Search Documents

The SFR system utilizes a skimmer or extractor placed at or near the slurry-froth interface where there is a higher concentration of valuable mineral particles. With assistance of hydrocyclones, it is possible to classify the extracted particles into coarse and fine particle streams, that can be handled separately. It also allows the coarser solids to be separated from entrained low-value fines. The first test results with the SFR system significantly improved both coarse and fine particle recovery in a flotation cell. The SFR system was tested in the flotation circuit at a copper-moly concentrator, and the results show that the use of the skimmer has huge potential to increase the froth recovery (Rf) of both molybdenum and copper.

Jan 1, 2012

Pressure Oxidation of Sulfide Gold-Bearing Concentrates with Double Refractoriness

Sep 13, 2010

By G. Van Weert

Mining project feasibility is projected from a geological model and a mining plan. Ore grade is assumed to be continuous, based on drill hole assays as much as 80 m apart. Eighty meter is 80,000,000 micron. Base metal concentrators may be said to work at 80 micron, for flotation at least. In short, metallurgical and financial performance in green field metal mining is forecast on rejecting waste after comminuting the ore down by roughly a volume factor of 1,000,000,000,000,000,000 (1018) from the feasibility/banking study parameters. This is the gap between mine and mill, between present sulphide mining practices and mineral dressing capabilities, and ultimately between lenders/shareholders expectations and mine/mill performance. By inserting a new upgrading technology in this gap, new opportunities for reserve enhancement and cost reduction are created, and risk could be reduced. Blast holes for extracting the outlined ore might be 8 m apart. Most ore bodies do not abruptly change composition at 8 m intervals; nor are they homogeneous in grade at the 8 cm (3?) rock size, optimum size for sorting. Mining in 8 m blocks will inevitably cause dilution of the mill feed and ore losses in the waste rock. This is well recognized in the mining industry. Much work is going on applying the vast data storage and manipulation capability of computers to mine scheduling. One only has to consult the SME Annual Meeting presentations. At the 2007 Meeting, Clark and Dagdelen described the challenges faced by Newmont at its operations and the application of sophisticated software tools and methods in its search of solutions to mining optimization. Block models can often contain in excess of one million blocks. Additional complexity exists when multiple grades are modeled for each block. The authors identify the main optimization problem as the system?s ability to cater to large scale problems in an acceptable timeframe; in other words, still larger computers are needed. At the same Meeting, Menabde et al (2007) presented a new pit development planning tool called Blasor, developed by BHP Billiton Technology, and its co-developed Blasor IPD (In Pit Dumping), (Zuckerberg et al (2007)). For purposes of this paper, Blasor/IPD incorporates options on processing capacity constraints and blending targets, eliminating arbitrary up-front decisions about cutoff grades for each block of material in the extraction sequence.

Jan 1, 2008

By J. P. Sancho, L. F. Verdeja, J. I. Verdeja

"This paper analyzes the present state of the different processes competing to keep their market shares within the future iron and steel business sector.The continuous transformations in the steel making process are also studied here. These transformations have happened especially during the two last decades obviously favouring steel price, properties, quality and environmental compatibility in the new millennium. IntroductionIn the early 1980s, world steel production reached a historic figure; specifically in 1982, the amount was 645 Mt (Verdeja et al., 1993). This might have been one of the reasons why the United States, Japan and the European Community drew up a declaration of principles after which the leading industries and sectors in the following century’s development would be: advanced materials, also known by the very diffuse term of new materials; information technologies; and biotechnology (Eager, 1998).On the threshold of the 21st century, it can be inferred that information technologies (computers and telecommunications) have progressed spectacularly. Nevertheless, there have been downsides too; technology develops so quickly that after a few months the products are obsolete. Environmental problems may also appear in a few years due to storing so many useless devices. At the same time, the achievements of biotechnology did not meet the optimistic forecasts made in the early 1980s.On the other hand, it is also curious that some solutions for the environmental problems generated by star technologies of the new millennium, such as computers and biotechnology, are closely linked to the iron and steel industry. For example, blast furnaces in Germany and Japan are prepared for burning residua by introducing polymer materials from computers and other electronic prepared devices through their tuyeres, while cement tube furnaces can destroy any organic residua from different origins."

Jan 1, 2002

By E. P. Deliac

The aim of this joint work between the French Coal Board and the Paris School of Mines is to be able to practically model the behaviour of a transverse drum cutting rock with picks. First a theoretical approach leads to the concept of cutting curves, giving forces and torque against penetration per drum revolution. Then experimental evidence, from full scale and reduced scale testing, validated and confirmed the theoretical shape of the curves. Finally practical applications are given, to improve the design or use of a shearer (or continuous miner). A micro-computer program is being developed to predict the cutting performances of a machine in certain conditions.

Jan 1, 1985

By Jack A. McQuiston, Thomas A. Cross

Corrosion of equipment and machinery in the coal industry is usually the result of three main agents: acids, chlorides, and abrasion. Acids and chlorides are especially troublesome in coal preparation plants where soluble salts and sulfur in the coal produce a highly corrosive wash solution. Abrasion is common in all operations where coal is handled or conveyed. Together, the acid-chloride-abrasion combination results in some of the worst corrosive conditions found in any industry. The variety of equipment and structures in the coal industry calls for different corrosion control techniques. Table 1 lists the areas of concern for a number of items. Just as there is a wide variety of corrosion problems, there is a wide array of coating materials available. Tables 2 and 3 are selection charts to provide guidance in narrowing down the choices. Experience has shown that a limited number of coating systems work best on coal equipment and structures. These systems are described in Table 4. The good-better-best designation in the table refers to coating system longevity. Good indicates the least costly and shortest service life. In nearly all cases the lowest annualized cost can be achieved by using the coating system rated best, due to the avoidance of costly repaints and unnecessary downtime. The most expensive coating system, though, is worthless unless the coating system is properly applied. Field inspection to insure compliance with specifications is an important aspect, and is a service available from many coating suppliers. Even the best coating systems require periodic maintenance to achieve satisfactory results. Spot rusting from mechanical damage should be repaired annually to maximize the coatingsystem's results.

Jan 2, 1980

By D. W. Rich

An environmental management system (EMS) is a key part of a company?s environmental stewardship. Procedures and practices to continually improve environmental performance can provide great benefits in operating the company. Managing site environmental quality data is a key component of this. An environmental data management system (EDMS) is an important element of the EMS for mining and other projects, providing project staff with the information that they need to make decisions that can have a significant impact on public health. Improvements in computers, data communications, and transfer formats have made it much easier to implement an integrated EDMS program for gathering, managing, selecting, and displaying data from the field and the lab. Software now lets users define sampling plans, create files for field data entry, and print Chains of Custody. Laptop and handheld computers facilitate field data entry and may provide automated communication back to the office. Most labs can now create usable electronic data deliverables. QC checks and limit comparisons can be largely automated. The result is organized data that can be efficiently used for reporting, graphing, and mapping, to better understand project issues.

Jan 1, 2009

By K. Peake, A. Dalvi, V. Hernandez, S. Chang, M. Oliazadeh

"Ironstone Resources Ltd. is developing the Clear Hills oolitic iron ore deposit in northwest Alberta, Canada. Sources of oolitic iron ore worldwide are abundant and ubiquitous, but there is currently no commercial technology to extract iron from oolitic iron ores. Mineral processing of the ore to generate a commercial iron ore concentrate is very challenging due to the nature of these ores. Accordingly, Hatch and Ironstone are developing a new pyrometallurgical process (Hatch Ironstone Chloride Segregation) to produce metallic iron from high silica and high phosphorus oolitic iron ores. Following the chloride segregation process, the treated ore is subjected to fine grinding. The iron is then separated by magnetic separation. The iron grade and phosphorus content of the final product shows a strong dependence on the separation methodology and the grind size. The pyrometallurgical process has been developed and tested at a lab-scale pilot plant. The commercialization of this technology could provide an opportunity for the development of a new alternate iron making technology. This paper presents the results of test work done on the raw iron ore to create a concentrate and also on the products of the pyrometallurgical process for the production of a high grade 90% metallic iron product.INTRODUCTION Oolite is a sedimentary rock formed from ooids – spherical particles with concentric layers. There are a number of large oolitic iron deposits where the mineralogical form features a low iron content and high concentration of impurities making them presently impossible to exploit on either a technical or economic basis. The fifteen largest oolitic iron ore deposits in the world are estimated to contain approximately 337 billion tonnes of iron ore, which would be a significant source of supply for worldwide steel production. A viable process that can economically recover iron from these oolitic iron ore deposits could become an important new technology to meet future demand in the steel industry. Hatch and Ironstone have demonstrated that oolitic iron ores can be exploited to produce direct reduced iron (DRI). Direct reduction ironmaking is a method for producing solid metallic iron using different techniques compared to the blast furnace process, which is the more conventional ironmaking route. The demand for the construction of direct reduction ironmaking plants has increased in response to the increasing demand for crude steel. It is viewed as a method of providing low-residual iron sources to scrap-based steelmaking in electric arc furnaces."

Jan 1, 2014

By Moussa Wone

The Washington, DC Water and Sewer Authority (WASA) has implemented facility planning for the Anacostia River Projects portion of a program to bring its Combined Sewer System (CSO) into compliance with federal water quality regulations by 2025. The program includes approximately 19 kilometers (12 miles) of deep CSO storage/conveyance and flood relief soft ground tunnels, construction, vortex drop, overflow, maintenance and air release shafts, as well as near surface diversion structures and conveyances. The Project encompasses major technical and non-technical challenges including completion under a federal consent decree schedule, construction within the confines of heavily developed urban areas, difficult ground conditions, major infrastructure crossings, and close coordination with several major public agencies. This paper discusses the planning stage considerations related to the geotechnical investigation program, discusses obstructions that influenced alignment selection, and provides two examples of preliminary estimates of settlement induced ground movement due to the tunnel and shaft construction.

Jan 1, 2008

By B M. Wilson, B J. Turner, S Sinclair, R J. Buerger

The Trident Gold Deposit is centred on the historical Higginsville Mining Centre, between the world class gold centres of St Ives (+15 Moz) and Norseman (+6.5 Moz) in Western AustraliaÆs productive eastern goldfields. It lies towards the southern end of the Norseman-Wiluna Greenstone belt in the Archaean Yilgarn Craton. The current in situ resource for Trident is estimated at 840 000 ounces, with production to date in excess of 500 000 ounces.Trident is hosted primarily within a thick, weakly differentiated gabbro with subordinate mafic and ultramafic lithologies and comprises a series of north-northeast trending, shallowly north plunging ore zones. The deposit comprises two main mineralisation styles; thin, lode-style, nuggety laminated quartz veins (Athena and Artemis) that formed along major shear zones primarily at the contacts between the various mafic and ultramafic lithologies; and large wallrock-hosted ore-zones comprising sigmoidal quartz tensional vein arrays and associated metasomatic wall rock alteration (eastern zone, western zone and Apollo) hosted exclusively within the gabbro.The thin laminated quartz vein lodes are important to the Trident Gold Deposits production profile as they constitute 33 per cent of the metal from only 14 per cent of the tonnes. The delineation, grade estimation and extraction of these lodes require a disproportionate amount of geological and engineering input due to the small scale variability in width, grade and direction. Over time, a robust and thorough process has been developed at the Trident Gold Deposit to understand and then successfully mine these complex mineralised systems.CITATION:Sinclair, S, Wilson, B M, Buerger, R J and Turner, B J, 2012. The mining industry needs to be shaken and stirred, in Proceedings Narrow Vein Mining 2012 , pp 155-166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By E. A. Sarver

The Fe(II) regeneration process is an important aspect of Alternate Anode Reaction Technology (AART) for copper electrowinning (EW). In AART, Fe(II) is oxidized to Fe(III) at the anode during EW, and it must be regenerated to maintain recyclable electrolytes. Regeneration is achieved via Fe(III) reduction by SO2(aq), and the reaction is catalyzed by activated carbon particles. To better understand this process, a kinetic model was developed and experimentally validated for the Fe(II) regeneration in the current work. The investigation focused on the primary reaction mechanism and the reaction rate dependence on four variables: carbon particle size, flow rate, initial Fe(III) concentration and initial SO2 concentration. The Fe(II) regeneration reaction is mass-transfer controlled in the presence of activated carbon. Carbon particle size and initial Fe(III) are the most influential factors under the conditions tested. Initial SO2 concentration is insignificant to the reaction rate.

Jan 1, 2007

By José Cayetano

El presente trabajo plantea un proceso para minimizar el contenido de bismuto en las celdas de electrorefinación, a través de la adición de carbonato de bario a la solución electrolito, de forma que el bismuto soluble presente en fase líquida, se precipite sobre la superficie del precipitado insoluble de BaSO4, bajo una coprecipitación por adsorción e intercambio debido al equilibrio dinámico entre el precipitado y la solución de electrolito conteniendo al bismuto. En este sentido, se reduce la presencia del bismuto en el electrolito de cobre en un 75%, adicionalmente se tiene la disminución del contenido de plomo en un 96%, de estaño en 48% y de plata en un 18% aproximadamente.

Oct 21, 2015

By T Medhurst

Recent developments in geophysical borehole log analysis using the Geophysical Strata Rating (GSR) are now routinely used in a number Australian coal mining operations. This allows development of 3D geotechnical strata characterisation models for a range of purposes. The availability of this data provides a means to identify relationships between ground conditions and ground behaviour. As a result, several new design methods have been developed to assist in the strata management process such as roof support, longwall shield design and shaft stability assessment. This paper outlines these methods and provides examples of their application. CITATION:Medhurst, T, 2018. Geotechnical strata characterisation using geophysics and its application for coal mine design, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 420–433 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By W. J. Birch, L. Bermingham

Air overpressure is becoming an increasingly problematic issue within the quarrying industry. With blasting operations moving ever closer to residential properties, the number of complaints about air overpressure is beginning to increase. It is therefore important for operators not only to have a greater understanding of the blasting parameters that give rise to air overpressure but also the factors which have an effect on air overpressure levels as it attenuates with increasing distance from the location of the blast.

Jan 1, 2013

To improve the ventilation of large-opening under-ground stone mines by using stoppings made from stone left in place. Background Underground stone mines typically use large room-and-pillar openings with little ventilation control. Stone miners may be exposed to contaminants that include silica dust, diesel particulate matter (DPM), exhaust gases, nuisance dust, and face shot (blasting) fume gases. The health risks from breathing these fine particles and toxic organic materials are well documented. Although contaminants such as dust or diesel exhaust can be some-what controlled at the source, the escaping contaminants are often diluted and removed from work areas using ventilation with minimal controls. In many cases, current mine ventilation practices use trial-and-error techniques to improve ventilation. The growing realization of the importance of a healthy work environment along with increased regulations will require many stone mines to implement new ways to improve ventilation. In-place stone stoppings are one option. Mine air flows from one point to another because of a pressure differential between those points. This pressure differential is established using a mechanical fan in conjunction with separations (stoppings) between high-pressure (intake) and low-pressure (return) airways. The separation of intakes and returns is an important concept that is used in most other types of mines. Normally, air moves through underground stone mines with minimal control technology. Fans are placed in locations where they are thought to be most beneficial, and intakes are not separated from returns. In a few smaller underground stone mines, proper ventilation can be achieved with a few strategically placed fans. However, as these mines increase in size, moving adequate quantities of air through-out the mine becomes harder, and separation of intakes and returns becomes a problem. Building traditional mine stoppings to separate the intake and return airways in entries with a cross-section area often exceeding 800 ft2 is difficult. The stoppings must be able to withstand both the dynamic pressure from face shots and the static pressures created by the fans. Construction and maintenance difficulties, as well as high costs, are the main factors preventing these traditional mine stoppings from gaining wide acceptance by the stone mining industry.

Dec 1, 2002

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Ertugrul Kaya, Kagan Ozdemir

The results of bench blasting on quarries, have important influences on the performance of subsequent mining activities such as loading, hauling, crushing, grinding etc., and the total costs of that mine. Drilling and blasting is an important step in mine producing chain and its results such as fragmentation, muckpile shape and looseness, dilution, damage and rock softening effect the efficiency of downstream processes. Within the scope of this study, the three different hydraulic excavators’ working performances have been studied considering the particle size distribution after bench lasting at a quarry in Istanbul Turkey. Five shots have been realized on the quarry and average particle size of muckpile after each shot were assessed by digital image analysis method. Bucket loading times have been measured by stopwatch study after five shots. Excavator bucket loading times were also estimated by bucket loading time estimation formula which was published in ISEE 2007 Conference, Ozdemir et al. 2007. Estimated and measured times have been statistically analyzed and the accuracy rate of formula has been determined for five events.

Jan 1, 2008

By G J. Corbett, T M. Leach

A continued exploration programme has further defined the geology of the Tolukuma vein system, verified the resource indicated by Newmont, and identified potential for additional mineralisation. The resource at Tolukuma Hill, designated as zone C, is a mine recoverable 432,000 t at 18.1 g/t Au & 46 g/t Ag. Mining will be by a combination of open pit and underground at a rate of 100,000 t per annum. Processing will be by SAG mill, gravity circuit and CIL plant. A diatreme breccia, localised at an intersection of structures and a relationship of gold to base metal sulphides, are indicative of a strong porphyry association. Typical epithermal features such as crustiform banded quartz and quartz pseudomorphing platy calcite are also present and locally contain lesser gold mineralisation. Pre-existing dilatant structures have acted as a host to the ore fluids, resulting in the formation of the semi-continuous Tolukuma-Gulbadi veins over a 1100 m strike. A fluid flow model suggests that mineralizing fluids were sourced from a diatreme margin and migrated laterally along dilatant structures. Bonanza gold grades are interpreted to be derived through fluid quenching in the flexure between a hanging wall split, which hosts much of the Tolukuma Hill resource, and the feeder graben structure. Thus, the relationship between the pre-mineral structural geometry and fluid upflow at the margins of a diatreme breccia, controls the ore setting.

Jan 1, 1995

By V. A. Phillips

Transmission-electron micrographs of electro-thinned samples of bulk-aged Cu-3.1 pet Co alloy show an aging sequence, supersaturated solid solution — coherent particles — quasi -coherent particles — noncoherent particles. Hardening is due to precipitation of coherent spherical fee coball-rich particles showing coherency strain fields, which are resolved at between 15 and 30A diameter. Loss of- full coherency did not occur until well into the overaged region, even with the assistance of deformation after aging. Different average particle diameters of 123, 92, and 149 ± 10Å were observed in samples aged to peak yield strength at 600°, 650°, and 700°C, respectively, indicating that there is no critical size for peak hardening. Noncoherent particles tended to develop (111) faces and became octahedral in shape. Dislocations tended to nucleate spherical coherent particles which eventually grew together forming large elongated particles. The surface energy of a noncoherent (low-angle) inter-phase boundary is estimated to he about 50 ergs per sq cm. A number of particle lining-up phenomena were observed. Overaging is principally attributed to increase in particle spacing, progressive loss of coherency, and increase in amount of discontinzdous precipitation. COPPER dissolves about 5.6 at. pet (5.2 wt pet) of cobalt at 1110oC1 and the solubility decreases to 0.75 at. petl (0.54 at. pet)2 at 650°C and to 0.1 at. pet or less at lower temperature.' It has been known for many years3-5 that Cu-Co alloys are capable of age hardening. Since cobalt is fee above 417°C and its atom size is only about 2 pet smaller than that of copper, precipitation of coherent particles would be expected. The equilibrium phase precipitated at 700°C and below contains about 10 pet Cu in solution which tends to stabilize the fee structure, lowering the transformation temperature to 340oc.l The alloy is known to undergo discontinuous precipitation in addition to general precipitation; while the former can be seen with an optical microscope, the latter precipitates are not visible except in the grosly overaged condition.5, 6 Extensive use has therefore been made of the ferromagnetic properties of the precipitate in order to follow the course of aging, and it has proved possible to measure the average particle size, spacing, approximate shape, and volume fraction and to determine that the particles are coherent without ever seeing a particle (see for example Refs. 2, 7, and 8). The magnetic measurements of particle size are limited to diameters below about 120Å.7 The present study was undertaken using the techniques of transmission-electron microscopy in order to check the above conclusions, to extend the previous magnetic work to larger particle sizes, and to attempt a more detailed correlation of properties and structure. A portion of this work has already been published.9-11 The present paper is concerned with the metallographic features of precipitation in relation to aging curves. Bonar and Kelly12'13 have published preliminary results of a similar study on single crystals of Cu-2 at. pet Co. EXPERIMENTAL Preparation of Alloy. A Cu-Co alloy, containing 3.12 wt pet (3.36 at. pet) Co by analysis, was prepared from 99.999 pet purity oxygen-free copper and electrolytic-grade cobalt. The alloy was melted and cast in vacuo in a high-frequency furnace using a graphite crucible and mold: Analysis showed chat 0.004 pet C was picked up during melting. The 1-1/2-lb ingot was homogenized in hydrogen for 24 hr at 1000°C. Slices were cold-rolled to 0.005 or 0.003 in. thickness, with an intermediate 650°C anneal in hydrogen at 0.080 in. thickness. Batches of six to ten strips were solution-treated in sealed-off quartz tubes in high vacuum in a vertical furnace and quenched by dropping into iced brine containing a device which snapped off the nose of the tube. Solution treatment consisted of 1 hr at 990°C or 2 hr at 965°C. The latter was employed for all mechanical-property studies, since a tendency was noted for the higher temperature to give porous material. Strips were usually aged individually in a horizontal vacuum furnace, inserting into the hot zone and withdrawing into a cold zone without breaking the vacuum. This method gave a rapid heating rate, permitting the use of short aging times. In some cases, particularly for the longer aging times at the higher temperatures, samples were sealed individually in quartz tubes in high

Jan 1, 1964

By Janis A. Shandro

The mining sector is a major economic driver for Canadian, and British Columbian communities. In parallel strong commitments have been made by industry to the well-being and sustainability of associated communities. However, these dimensions are the least understood. Especially lacking are focused regional investigations that compare the well-being and sustainability of communities dependent on different resources sectors. It is hypothesized that this type of comparative analysis will help to foster a greater understanding of what makes a resource or mining community healthy and sustainable. This paper describes research that examined community-level indicators associated with well-being (e.g. education, income and employment) and sustainability (e.g. economic diversity). The indicators were derived from Canadian Census data for 31 British Columbia resource-based communities (with a focus on mining) during a period of time (1991 to 2001) when resource sectors experienced an economic downturn. Our findings identify that during this decade, mining communities differed significantly from other resource-based communities, and comparative analysis of census derived indictors illuminate challenges that mining communities in British Columbia face with respect to wellbeing and sustainability (such as economic diversity, unemployment, and population loss). To contribute to the mining sector?s efforts towards meeting their commitments to communities, this paper concludes by proposing strategic opportunities aimed at the enhancement of mining community sustainability for policy-makers, communities, and the mining industry to consider.

May 1, 2011

By Dennis R. Dolinar

Screen material in the form of welded wire mesh and geogrids are used in underground coal mines to prevent the fall of small pieces of rock from the roof between roof bolts. Further, if the screen is installed during the production cycle, roof fall injuries can be reduced significantly. Therefore, the National Institute for Occupational Safety and Health (NIOSH), because of the safety implications, conducted an evaluation of screen materials commonly used in U.S. coal mines to determine their support characteristics and identify the parameters that could affect their performance with respect to controlling the fall of rock from the roof surface. To evaluate the load and stiffness characteristics of the screen, a test frame was designed and installed in the Mine Roof Simulator (MRS) at the NIOSH Pittsburgh Research Laboratory (PRL). With this test set up, the screen is bolted at four corners of the frame and a center load is applied. The test set up allows for up to 20 in of screen deflection while the load and screen defection are continuously recorded. A series of tests were conducted to evaluate the effects of various parameters such as bolt tension, the type of load bearing surface and the size of bearing plates on welded screen performance. The most common screen material used in U. S. coal mines is an 8-gauge wire welded in a 4-by-4-in spacing or aperture. The peak screen load was normally limited by wire breakage. The conditions at the bearing plate influence the nature of the wire breakage. However, the screen stiffness was controlled by slippage at the bearing plates, and by weld and wire failure. The size of the bearing plate had a significant effect on the performance of the welded screen. Therefore, the design capacity of the 8-gauge screen is evaluated based on plate size. For a 6-by-6-in bearing plate the average peak load is 2,900 lb with a stiffness of 250 lb/in. For an 8-by-8-in bearing plate, the average peak load is 4,500 lb with a stiffness of 430 lb/in. These test results are based on a 4-by-4-ft bolt spacing. A geogrid mesh was also tested.

Jan 1, 2006