Search Documents

By E. P. Abrahamson II

The effect of transition elements which form binary solid solution upon the recrystallization temperature of zirconium has been investigated. All additions raised the recrystallization temperature. A correlation is obtained between the logarithm of the rate of change of recrystallization temperature with atomic percent solute and the free atom ground state electron configuration of the solute element. ThE work of Abrahamson, et al., on dilute binary solid-solution alloys indicated a correlation between the free-atom ground state electron configuration of the solute and either the brittle-ductile transition or recrystallization temperature. These studies were carried out on bcc base materials. The implication is that the outer s and d electrons of the solute are the prime determinant of the absolute rate of change of recrystallization or transition temperature. Furthermore, the limit of linearity has been shown to be a function of solute electron configuration for recrystallization in iron and vanadium. To date no Complete systematic recrystallization study of dilute binary zirconium base alloys has been made. It is the purpose of this study to note whether the change in solvent structure from bcc to hcp will influence the correlation. It was also desired to learn more of the role of the electron configuration of the solvent on recrystallization temperature. PROCEDURE All alloys were made using 99.87 pct Zr with 0.01 Cr, 0.04 Fe, 0.006 Hf, 0.003 Mg, 0.003 Mn, 0.003 N, and 0.080 0 (132 BHN). The solute elements were 99.9 pct pure. According to the published binary phase diagrams6 and metallographic examinations at X750, all alloys used were solid solutions. The alloys were arc melted and remelted six times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot pressed at 950°C to 0.450 in., upset pressed to 0.350 in., and annealed at 800°C for 1 hr. The specimens were then Blanchard ground to 0.250 in., removing 0.050 in. from each side. The grain size of the material at this stage was found to be 8000 100 grains per sq mm. The specimens were then cold rolled to 0.130 in. and cold pressed to 0.125 in., yielding 50 1 pct cold work. All alloys were then chemically analyzed for the principal addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The rolled sheet was cut into 6.75 by 0.25-in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was 250o to 900°C over the 6-in. length, recorded continuously by six thermocouples resting on each specimen. Control was 3oC, accomplished at the hot end. The recrystallization temperature was determined metallographically using polarized light. The criterion chosen was the point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be 3°C. RESULTS Three different pure zirconium specimens were tested, and the recrystallization temperature was

Jan 1, 1962

By G. A. Gamble

Fans used to ventilate subway, passenger rail and vehicular tunnels are similar to the fans used to ventilate underground mines. However, tunnel ventilation fan systems are typically designed to meet NFPA 130 or 502 standards, while mine ventilation fan systems must comply with the appropriate federal mine safety regulations. As a result, fan operation requirements and performance criteria, as well as typical fan and duct configurations differ significantly for tunnel and mine ventilation applications. Variations in environmental conditions in tunnels as compared to mines also result in differences in fan performance and material specifications. The need to enclose tunnel fans within building structures creates space restrictions impacting fan size selection that are not commonly encountered in mine fan installations, resulting in different approaches to selecting fans for the two types of tunnels. This paper discusses the various similarities and differences in design considerations for tunnel and mine ventilation fans.

Jan 1, 2009

By Harry C. Gatos, Frank J. Bachner, Mario D. Banus

The portion of the Nb-Sn phase diagram between 75 and 79 at. pct Nb at temperatures near the liquidus has been investigated by melting alloys of known composition and examining the microstmc-tzlres resulting when these melts were quenched. The Nb-Sn samples were contained in magnesia sleeves, and were mounted in a high-pressure apparatus. It was shown that Nb3Sn me1ts by a peri-tectic decomposition and that the composition of the compound Nb3Sn at the peritectic horizontal lies between 77 and 78 at. pct Nb. Analysis of the phases present in the samples was accomplished by anodic staining techniques and an electron-microbeam analyzer. DURING the past several years a great deal of work has been devoted to the Nb-Sn system, and the bulk of this work has been primarily concerned with the intermetallic phase Nb3Sn. However, the melting characteristics of Nb3Sn have not been investigated because of the difficulty in maintaining known compositions due to tin losses by vaporization, and the added difficulty of containing Nb-Sn alloys without sample-container reaction at the high temperatures involved. This paper reports on the development of a technique for containing Nb-Sn alloys under pressure high enough to prevent tin losses at temperatures in excess of the liquidus. Using this technique, melts of known composition were made and a phase diagram near the liquidus is proposed based on the microstructures resulting when these melts were quenched. EXPERIMENTAL The Nb-Sn alloys weighing 0.7 g each were prepared in the form of cylinders. Niobium powder, -200, +325 mesh, and tin shavings with a minute amount of tin powder for a binder were mixed in the desired proportions and cold-pressed at 50,000 psi in a 0.150-in. die. This cylinder was then enclosed as shown in Fig. 1, and the entire arrangement mounted in a 2.6-in. pyrophyllite tetrahedron.' The desired temperatures (-2500°C) presented several problems in high-pressure container materials. Boron nitride, the usual sample holder, was found to react with niobium to form the nitride. However, MgO cans and plugs machined from refractory rods did not melt nor react with the sample. Thick tantalum contact disks were used to carry the large currents (~450 amps) to the graphite heater, since tantalum did not melt and had enough strength to prevent extrusion of the sample. It was further observed that the graphite heater and tantalum disks could not be in direct contact with the pyrophyllite because it melts and decomposes at these temperatures to kyanite and coesite (SiO2),2 the former reacting with graphite and the latter with tantalum to form the silicide. The use of a MgO outer sleeve

Jan 1, 1965

By A. B. Cecala

Over the past decade, a substantial effort has been made to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment to reduce respirable dust exposures to the equipment operators. As part of this effort, the National Institute for Occupational Safety and Health, (NIOSH) completed a comprehensive laboratory study which determined the significant factors for cab filtration and pressurization systems. From this information, a major underground mining equipment manufacturer designed a filtration and pressurization system which was incorporated into the enclosed cabs of its equipment. A long-term evaluation was performed on the effectiveness of this filtration and pressurization system to improve the air quality in the enclosed cabs of two different pieces of equipment, being a face drill and a roof-bolter machine, at an underground limestone mine. This long-term evaluation demonstrated a significant reduction in dust levels comparing outside to inside cab respirable dust concentrations. During this evaluation, a modification to remove one of the filters on the roof-bolter machine simplified the design without sacrificing the system?s efficiency. Testing using particle count instruments performed during non-production time periods on both pieces of equipment indicated Protection Factors greater than 100 when comparing respirable-sized dust particles inside the enclosed cab relative to outside.

Jan 1, 2012

By Clive Ellis, Brian Davies, Steven E. Mischler, Jon C. Volkwein

A primary means to reduce environmental levels of diesel particulate matter (DPM) exposure to miners is to reduce the amount of DPM emission from the engine. A quick and economic method to estimate engine particulate emission levels has been developed. The method relies on the measurement of pressure increase across a ?lter element that is brie?y used to collect a DPM sample directly from the engine exhaust. The method has been re?ned with the inclusion of an annular aqueous denuder to the tube which permits dry ?lter samples to be obtained without addition of dilution air. Tailpipe ?lter samples may then be directly collected in hot and water-supersaturated exhaust gas ?ows from water bath-cooled coal mine engines without the need for dilution air. A primary means to reduce environmental levels of diesel particulate matter (DPM) exposure to miners is to reduce the amount of DPM emission from the engine. A quick and economic method to estimate engine particulate emission levels has been developed. The method relies on the measurement of pressure increase across a ?lter element that is brie?y used to collect a DPM sample directly from the engine exhaust. The method has been re?ned with the inclu­sion of an annular aqueous denuder to the tube which permits dry ?lter samples to be obtained without addition of dilution air. Tailpipe ?lter samples may then be directly collected in hot and water-supersaturated exhaust gas ?ows from water bath-cooled coal mine engines without the need for dilution air.

By Li Zhang

Air was blown into the molten slag as oxygen resource during the dynamic oxidation. It was found that the oxidation is not only in favour of Ti components into perovskite phase, but also the increase of slag temperature and decrease of slag viscosity during the dynamic oxidation promote the precipitation and growth of perovskite phase, average crystal size of perovskite phase is 48 µm. The experimental result realizes the selective enrichment of Ti components and coarsening of perovskite phase, perovskite phase can be separated by mineral dressing method.

Jan 1, 2009

By Garry Johansen, Andrew McCallum, Sandy Gray, Gary Patrick, Jennifer Abols

"The authors challenge the traditional thinking that whole ore cyanidation followed by Carbon in Pulp (CIP) or Carbon in Leach (CIL) should be applied as a standard process in the majority of gold processing flowsheets. The concept of whole ore leaching by using cyanide can result in unnecessary environmental and capital risk. Alternative, currently available technologies can be used to provide the desired level of gold recovery at a much lower installed cost and less impact on the environment. Gravity concentration, alone or in conjunction with flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit.The InLine Leach Reactor (ILR) is an intensive cyanidation unit developed by Gekko Systems of Australia. Advantages of this technology include significantly reduced capital outlays for greenfield plants or plant upgrades and increased investor returns. Reduction of onsite cyanide and carbon inventories improves plant safety, materials handling and site security. By using direct electrowinning to treat the gold bearing solutions produced by the ILR, the need for a conventional carbon stripping circuit is removed. Potential also exists to increase grind size – saving energy, further reducing capital and operating costs and decreasing the environmental impact of a mill. Detoxification of cyanide before the release of solution to the tailings dam can minimise tailings disposal and containment requirements.When used in the right application the proposed process will have little or no impact on gold recovery and may actually increase recovery for complex ores. Areas applicable to this type of treatment include: plants in environmentally sensitive regions, lower tonnage higher grade deposits, coarse gold deposits, and preg robbing ores - some of which may not currently be economically feasible using standard processes and flowsheets. We have provided three examples of such projects, where an alternative to whole ore leach and CIP or CIL has delivered these benefits."

Jan 1, 2003

By Stephen H. Chung, Kevin Atherton

The main purpose behind this preliminary study was the reduction of costs while maintaining productivity. Finding a way to achieve this balance without compromising controls on safety and quality of blasting results is of continual interest to the mining industry and of particular interest when ore of lower grade is being mined.

Jan 1, 1998

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

By R. V. Typliski, G. J. Labarre

"Hudson Bay Mining and Smelting Co., Limited, Flin Flon, Manitoba, Canada, has developed a metallurgical wastewater treatment system employing two-stage lime neutralization, sludge recirculation and conventional mechanical thickening.Laboratory investigations, initiated in 1970, led to the construction of a pilot-scale minewater treatment plant, at Schist Lake Mine, in early 1971. This plant, treating 600 cubic meters/day wastewater containing 30-60 mg/l zinc, demonstrated metal extraction efficiencies of 99% under normal operating conditions.On the basis of this pilot work, a second pilot-scale treatment system was established in 1975 at the Flin Flon metallurgical plant to treat zinc refinery process waste water. Through numerous improvements, including automatic control equipment, the system has evolved to a full-scale operation capable of treating 800 cubic meters/ day wastewater containing 4-11 gm/l zinc. Treated effluent contains 0.2-20 mgll zinc. Hydroxide sludge produced returns to the metallurgical process for recovery of metals while clarified effluent discharges to waste.With the system, Hudson Bay Mining has achieved its original goal: the reduction of environmental contamination, while realizing ii return from metal recovery."

Jan 1, 1980

By Glenn Clarke, Ben Holloway, Barry Lumsden

"BHP-Billiton’s Cannington mine in Northwest Queensland produces a silver-rich lead concentrate and a zinc concentrate. The plant has the capacity to treat 3.1 mta and for the year to June 2006 mean feed grade was 10.3% Pb, 461 g/t Ag and 3.7% Zn. Recovery losses of lead and silver are primarily in the fine fractions. In 2001, the plant was modified when it was determined that splitting the lead feed into two size fractions, and floating the two fractions separately increased fine lead and silver recovery. The fine lead fraction (called the split float) is 80% <16µm and about a quarter of the lead and silver is in the finest fractions. In 2006 to further improve lead and silver recovery a statistical plant trial of magnetic aggregation conditioning of the split float feed was undertaken. While pure galena is diamagnetic the Cannington galena contains iron within the galena mineral resulting in the galena having a paramagnetic, magnetic susceptibility. The trial demonstrated to greater than 98% statistical significance an increase in lead recovery, and to 99% statistical significance an increase in silver recovery, and to greater than 97% significance an increase in the lead in concentrate in the split float circuit. These economic recovery benefits with magnetic aggregation of the split float feed, has led to the incorporation of this technology in the plant.INTRODUCTIONThe BHP-Billiton owned Cannington silver, lead and zinc mine is located in the Australian state of Queensland about 800 kilometres west of the coastal city of Townsville. This is a pastoral area characterised by large cattle farms, low population density and very little infrastructure. The area has two seasons, a wet, hot summer and a dry, mild winter. Because of its isolation and lack of infrastructure the mine has always operated on a fly in fly out basis.Geological drilling defined the resource as 43.8 million tonnes grading 11.6% lead, 4.4% zinc and 538 ppm silver (Walters and Bailey, 1998). At times during its history Cannington has held the crown as the single largest lead and silver mine in the world (Torrisi and Smith 2003). Another unique characteristic of the operation’s history is the rapid progress from discovery to operation. The first drill to intersect the ore body was in 1990 and the mine and plant was commissioned in 1997."

Jan 1, 2008

According to the classification of water conservation mining in shallow coal seams in China, when the ratio of the impermeable layer thickness to the mining height is less than 18, the mining belongs to the category of special water conservation, and the strip backfilling mining method is employed. This study is based on the geological conditions in northern Shaanxi. By analyzing the stability of the impermeable layer, the stability criterion of the impermeable layer was developed. The study also investigated the compositions and properties of the backfilling materials. The results show that reasonable subsidence of the impermeable layer is allowed during mining under the basic precondition (upward cracks and downward cracks are not connected).

Jan 7, 2020

By John Meuth, Brandon Fryman, P. E. Hoffman, Joshua Ph. D., P. E. Calnan, Josh Ph. D.

Quantitative Risk Assessment (QRA) can be specifically tailored for use by the commercial explosives industry to calculate risk to employees and the public from commercial explosives facilities and operations. This methodology has several advantages over the American Table of Distances (ATD) which is solely a Quantity Distance (Q/D) analysis. While the ATD has remained essentially the same for 100 years, the safety of commercial explosives in storage has increased immensely. However, the concepts behind QRA calculations are not as intuitive and even at the end of the calculations the values of risk must be compared to something. A few regimes for assessing an acceptable level of risk are discussed in this paper. Risk levels for various United States Federal entities and international agencies are highlighted and suggestions for acceptable risk criteria for individuals and groups are provided. Referencing risk levels from normal daily activities is also done in this paper to make relative the accepted risk criteria. This paper presents some relevant individual risks for everyday activities and some scenarios for group risk for comparison. Individual risk is a straightforward concept however group risk is more complicated. This paper aims to clarify these concepts and provide means to communicate them to the public.

Jan 1, 2019

By Khandaker M. Anwar Hossain

This paper presents the development of lightweight concrete (LWC) incorporating pumice aggregate and volcanic ash (VA) based ASTM Type I blended cement (PVAC). Fresh and mechanical properties of LWC mixtures such as slump, air content, compressive strength, tensile strength, density and modulus of elasticity are described. The durability characteristics are investigated by drying shrinkage (DS) and water permeability. The investigation suggests the production of LWCs incorporating blended PVAC and VPA having satisfactory strength/durability characteristics for structural applications. The use of PVAC induces the beneficial effect of reducing drying shrinkage and water permeability. Development of such non- expensive and environmentally friendly LWCs with acceptable strength and durability characteristics is extremely helpful for the sustainable development and rehabilitation of volcanic disaster areas around the world.

Jan 1, 2010

By Michael J. Potter

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. In June, Azrock Industries was purchased by the R L. White Co. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); by Ziegler Chemical and Mineral Corp.; and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds.

Jan 1, 1985

By O E. Jr Crenwelge

Frequency domain, single-charge vibration signatures are used to interpret the characteristics of explosive impulse excitation and ground vibration transmission. The effects of charge height, charge splitting, and different blasting agents are first discussed. Then the effects of rate of change with distance of overburden material properties and layer or surface geometries are illustrated.

Jan 1, 1988

By Alex C. Smith, Thomas A. Gray, Lynn M. Crayne, Michael A. Trevits, Phil Glogowski

Mine fires constitute one of the greatest threats to the health and safety of those working in the underground environment and each event has the potential for disastrous consequences. Of the major mine fires and thermal events that have occurred in the United States in the last 6 years, it is estimated that remotely installed seals could have been used in 63% of the events to control fire growth or to aid in fire suppression work. The National Institute for Occupational Safety and Health (NIOSH) is conducting full-scale tests at the NIOSH Lake Lynn Experimental Mine to evaluate and improve remote mine seal construction technology. The main focus of this work is to develop reliable technology that will completely close the mine opening from floor-to-roof and rib-to-rib. This paper presents the results of remote seal installations using grout-based materials.

By John Wilson

"The Rietveld numerical method was used to calculate the relative abundances of phases in both synthetic binary mixtures and synthetic and natural ores, using X-ray diffraction data. The results were compared with those of image analysis and a chemical method. The ranges of the relative errors were estimated. The Rietveld method is found to be acceptable for determining the abundances of major and minor phases and the amorphous component of partially crystalline samples. In complex mixtures, where there are several trace phases (~<2 wt%) present, the technique becomes less accurate. It is most useful as an alternative technique to image analysis when sample preparation is problematic or sample particle sizes are sub-micron. It is a manual method which requires user input during the fitting process, but is both simpler and faster than image analysis due to the reduced set up time and sample preparation required. It is now implemented at CANMET as a technique for quantitative analysis.INTRODUCTIONUntil recently, the Applied Mineralogy group at CANMET used only image analysis and chemical techniques to determine phase quantities. An effort to develop quantitative X-ray diffraction (XRD) has been on-going for several years. Initially, the reference intensity ratio (RIR) method with external standards was tried with some success (Szymanski and Petruk, 1989). The main difficulty with this technique was finding adequate standard material for each phase present in the sample. This shortcoming made the method ultimately impractical, given the wide variety of materials which come to the laboratory for analysis.The Rietveld refinement method of quantitative XRD (Hill et al 1993, Mumme et al 1996), in contrast, requires no standards and requires minimal sample preparation and therefore a more rapid turnaround compared to image analysis. The Rietveld method also has advantages over image analysis in that it can identify and quantify polymorphs, ultra fine materials and many types of hydroxide products. As well, it is useful for analyzing materials such as bauxite or talc, which do not polish well enough for making mounts of the quality required for image analysis. To quantify amorphous material and phases which are present in amounts below the detection limit of XRD, the addition of a standard material is still required. However, in such cases only one standard is needed, which is alumina."

Jan 1, 2003

By R. Fragoudakis

AISI 4130 steel is a medium carbon Cr-Mo steel used in automotive, aeronautic and other general-purpose industries. In this study, 4130 steel fatigue specimens were carburized at 927oC to enhance the carbon content in the steel, raising it from approximately 0.30% (non-carburized) to 0.90% (carburized, oil quenched and tempered). Rotating bending fatigue tests were performed on the R. R. Moore Rotating Beam Fatigue Testing System, in order to determine the high cycle fatigue (HCF) life of 4130 steel and plot the corresponding S-N diagrams. A comparison of the results of carburized and non-carburized specimens shows that carburizing of steel: a) increases the surface hardness and b) improves the fatigue strength of the steel by at least two orders of magnitude.

Jan 1, 2010

Effective gas management in coal mines, as well as proper ventilation design, is very important for maintaining the safety of underground coal miners. Advances in numerical modeling techniques have enabled evaluations of the coal mining environment using advanced grid designs and computed gas distributions through detailed mathematical models. These models help engineers to see the unseen areas of the mine through visualization of the data and ultimately help improve worker safety. This paper summarizes the modeling efforts conducted by NIOSH in the U.S. and CSIRO in Australia to address various gas management issues encountered in longwall mines. The modeling studies involved two of the most widely used grid-based techniques, namely computational fluid dynamics (CFD) and numerical reservoir modeling. This paper discusses the application of these techniques for gob inertization and gas control for spontaneous combustion, pre-mining degasification of coalbeds, gob gas venthole design and performance evaluation in longwalls, and gas management during development mining.

Jan 1, 2009