Search Documents

By Shahid Islam, Lucian Bogdan

There is a rapid expansion of world’s infrastructure and simultaneously existing infrastructure is aging. The maintenance of infrastructures has been of particular concern to the engineering community. Monitoring and evaluating the structures have become more significant than ever. Ground anchor is an important part of the structure where it is installed. Unfortunately there are limited testing methods available to assess the force in the pre-stressing steel. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYNA Force sensors have been developed to measure the force in the pre-stressing steel during construction and at any time during the lifetime of the structure. These sensors make use of the magneto-elastic properties of ferrous materials. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. They can be used for bare, epoxy- coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the tendon. It measures the force of the steel element at the location where it is installed and can be recorded manually, automatically, or remotely. The sensor is robust, requires no maintenance and it is expected to have a similar service life to that of the surrounding structure. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. Sensor readings provide a second measurement, in conjunction with the jack pressure gauge, of the post tensioning force during initial testing procedure for ground anchors. This paper describes its application in tie-back and tie-down anchors and force monitoring of retaining walls, bridge abutment and dams where the data were collected manually, automated and remotely. INTRODUCTION Our infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.

Jan 1, 2018

This paper discusses the social and economic impact of mining, and in particular goldmining, on New Zealand. The range of topics covered and their complexity has confined us in this paper to highlighting the main points of concern û a detailed report is under preparation. A major problem in undertaking this study was the lack of hard data on important environmental, economic and social issues and if there is to be effective planning in the area of natural resource use this situation must be rectified. The following conclusions were drawn: Goldmining was very important in shaping New Zealand's early social and economic development, providing wealth, employment and impetus for social change.Foreign investment and technology has been an essential element in New ZealandÆs economic development.Mining is a small industry at present by this must not be allowed to obscure its potential to broaden New Zealand's economic base and provide foreign exchange.With modern methods, development of mineral resources and environmental protection are not incompatible but certain unique and irreplaceable areas must be preserved.There are problems in evaluating mining and other projects because different groups hold different values, and arguments often hinge on the valuation of costs and benefits rather than the technical aspects of the analysis.Mineral exploration is a high risk business and the potential returns must be sufficient to attract capital if New Zealand's mineral resources are to be developed.A resurgence of goldmining will clearly have obvious benefits for Waihi but the local community must plan carefully for their future. New Zealand will also gain valuable foreign exchange required for higher levels of economic activity.

Jan 1, 1981

By C. J. Farrow, M. J. Smith

"Bechtel has managed a number of test programs to establish autogenous grinding circuits and size mills for a variety of ores.This paper outlines the procedures whereby bench scale and pilot plant tests are used to select the most efficient circuit to grind the range of ore types likely in the mill feed.Five examples are given. One example traces the development of a pilot plant program; it shows how bench scale Work Indices provide a target for the grinding power requirement of an ore and relates how pilot circuits are changed as a result of interpreting the results from preceding tests. The other four examples relate the interpretation of the test results to provide design data; they illustrate a number of phenomena which have been observed.INTRODUCTIONConventional crushing and grinding circuits can be specified from bench scale test data such as Bond Work Indices. Bond Indices have been correlated to a large number of rod and ball mills and by applying appropriate factors, mills can be sized from the Work Index.For autogenous or semi-autogenous grinding circuits, bench scale tests are not sufficient to be able to specify the circuit and size of the mills for a commercial plant. It is necessary to run a series of pilot plant tests to determine how the ore behaves."

Jan 1, 1982

By C. Maree

Paper written on project work carried out in partial fulfilment of B. Eng (Chem. Eng.) This paper describes the development and use of a process simulator to optimize gypsum recovery at Afmine, a small plant near Yzerfontein on the South African West Coast. The simulator consisted of models of the major plant equipment, viz. hydrocyclones, surge bins, settling tanks, a primary sieve and a dewatering screen. Experimental data suggested that the equipment could be modelled satisfactorily from data published in the open literature. Simulation studies have indicated that gypsum losses on the plant could be reduced substantially by means of some relatively minor modifications to the plant layout. Moreover, sensitivity analyses of the plant have indicated that optimization of the settling tanks should receive priority over the other process units.

Jan 1, 2005

By Yi Luo

Subsidence events occurred over inactive room and pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidences to identify the causes are often lacking. In order to conduct a thorough and impartial investigation, good knowledge in subsidence theories and other ground control subjects and broad experience are required.

Jan 1, 2009

By P. J. Williams, A. R. Foster

Petrographic studies, assay records, and laser ablation-inductively coupled plasma-mass spectrometer (LA-ICP-MS) analyses of major sulfides suggest nearly all of the gold at the Ernest Henry Cu-Au deposit occurs in the form of native gold or electrum (95-65 wt.% Au); sylvanite and dissolved gold in cobaltite, chalcopyrite, and pyrite make only minor contributions. LA-ICP-MS analyses of the gold contents of chalcopyrite gave from 8 to 139 ppb (mean = 56 ppb), more than an order of magnitude lower than those experimentally determined in chalcopyrite in equilibrium with native gold at the estimated mineralization temperatures (350°-450°C). Gold content is more variable in pyrite (1-400 ppb, mean = 77 ppb) and highest in narrow growth zones of a subordinate type of complexly zoned pyrite wherein it is associated with elevated As, Ag, Sn, Sb, Te, and Bi. Deposition of gold-electrum was closely associated with, but preceded some of the chalcopyrite deposition, as indicated by microtextures and lower bulk Au:Cu ratios in late-stage chalcopyrite-rich veins. Gold grains have maximum dimensions from <1 to 50 micrometers, and are heterogeneously distributed with most occurring in microscale clusters. Fifty-five out of 76 grains recorded in polished sections are in contact with both chalcopyrite and pyrite, and many of the rest are in sites where such a relationship could exist in the third dimension. The dominant textural sites are intergrowths with chalcopyrite in microveinlets cutting pyrite, and on faces of pyrite grains in contact with chalcopyrite. Scanning electron microscopy, electron microprobe analysis, and proton induced X-ray emission studies show that pyrite associated with gold includes complexly zoned, weakly zoned, arsenian, and arsenic-poor types. The textures are compatible with the possibility that most gold was deposited electrochemically as native metal on pyrite surfaces. The textural distribution of gold has important metallurgical implications given that the ore processing circuits at Ernest Henry and most other sulfide copper mines are designed to exclude pyrite (and arsenic) from concentrates.

Jan 1, 2007

By T. Plikas, L. H. Gunnewiek, L. Oshinowo

Electric furnace smelting is one of the principal unit operations for ferroalloy production, and increased process intensity, improved availability, minimal maintenance and a longer campaign life are common objectives for electric furnace operation in order to obtain favourable economics of production. Furnace designers have continued to develop innovative solutions that have allowed these objectives to be realised, e.g., furnace cooling systems, and numerical modelling plays a key role in the design process. Enhanced understanding of the energy transfer process in the furnace and the ability to develop, evaluate and optimise components of the crucible design to match process requirements are the key motivators for modelling. This paper provides an overview of recent applications of numerical modelling to the design of electric furnaces. The aim is to illustrate what can be done, and identify areas where further work is needed in this field. Examples include furnace bath modelling, crucible cooling system design, taphole design, baking of Soderberg electrodes, off-gas systems, and fume control and building ventilation. It is argued that the trend is for numerical models to become more encompassing while at the same time more accessible, and therefore further improvements in furnace design will be realised with continued and well validated modelling efforts.

Jan 1, 2004

By Y. P. Chugh, J. Ma

Higher production, better safety standard, and potential for automation are some of the benefits of longwall mining. Today, longwall face advances at a faster rate exposing many diversified rock layers in a short period of time. It is now a serious challenge to cope with ground control problems such as roof falls, face and floor failure, and excessive shield loading as fast as possible to minimize production and monetary losses. In Illinois coal mines, the existence of weak floor strata blow the coal seam may pose additional problems related to floor heaving, shield base punching, and associated roof and face falls. In this study, the effects of weak floor on longwall ground control are analyzed using two-dimensional finite element models. A two-leg 635.6-ton (700-short-ton) yielding capacity shield is included in the models to evaluate the effects of different thickness and material properties of the weak floor. The study indicates that the thickness and material properties of weak floor have significant effects on shield loading, the distribution and intensity of front abutment stress, failure zones in the surrounding strata, roof-to-floor convergence, and floor punching by the shield base.

Jan 1, 2000

By Erik Westman

Few studies have been conducted regarding the location, movement, and relative magnitude of the rear abutment of a longwall coal mine. The rear abutment, or the abutment pressure arch in the gob area, is controlled primarily by the quality of pack of the gob; the more compacted the gob is, the larger the stress would be theoretically. While there is no definitive location for the rear abutment, early studies showed that it could be located as far back in the gob as 300 m (1,000 ft). Like the location of the rear abutment, there has been little research conducted and very few answers as to the exact magnitude of the rear abutment load. Due to the fact that the rear abutment has been studied considerably less than the front or side abutment, the need for further studies is evident. From a ground control standpoint, the location and magnitude of a rear abutment could reveal information on the caving process associated with longwall mining, such as when the initial cave could be expected to occur in future panels. Besides the possible importance of the rear abutment from a ground control perspective, evidence related to the longwall rear abutment could be vital from a ventilation standpoint. The peak rear abutment location could serve as an area for harmful gases, such as methane, to accumulate because forcing air through repacked rock is more difficult than through loose rock. The objective of this study is to determine whether passive seismic tomography could image the location, movement, and relative magnitude of the rear abutment as the longwall face retreated, in addition to the forward abutment and gob. The results of a passive seismic imaging study at a western US longwall show evidence for the location, movement, and relative magnitude of a rear abutment. A clear zone of highlystressed strata is shown where the forward abutment is expected and a low-velocity, damaged zone is shown behind the face where the gob is located. These two zones retreat with the face over a three-week period. In addition, the images show a return to stress levels behind the gob that are slightly higher than overburden stress levels, which is presumably the rear abutment. This occurs at a distance behind the face that is approximately the same as the face width for this mine. We can conclude that passive seismic imaging can be used to identify the location, movement, and relative magnitude of the rear abutment of a longwall mine. This conclusion is dependent on the use of appropriate data collection and processing methods. The information provided can benefit the both ground control and ventilation engineers as they strive to improve the safety and efficiency of longwall mines. The knowledge associated with the rear abutment of a longwall could not only help increase production through proper initial planning and reduce down time, but it could also make positive strides in improving the overall safety surrounding a longwall mining operation.

Jan 1, 2012

By Gabriel Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

Jan 1, 2007

By J. A. Bakken, G. Sævarsdóttir, H. Pálsson, M. Þ. Jónsson

The role of the electric arc in the consumption of electrodes in submerged arc furnaces has long been debated. The hostile environment in the furnace does not make direct measurement feasible, so simulation has been used to evaluate the arcs contribution to the erosion. Magnetofluiddynamic (MFD) electric arc simulations and a cathode / anode sub-model developed in order to provide boundary condition to the arc model have been used for this purpose. The cathode / anode sub-model provides current distributions and cathode / anode fall voltages for the arc and temperature distribution for the electrode surface, which is paramount to the erosion rate which in turn is calculated from the Clausius Clapeyron equation and the Hertz Knudsen formula for the vapour transport. In the case of high-current industrial AC arcs, arc currents are typically ~100 kA, phase voltages ~100 V and total furnace power ~10 ? 60 MW. The results show that although enormous amounts of material is evaporated, much of it recondenses on the surface. Furthermore the results show that the arc erosion increases strongly with the arc current. If a single arc is present its contribution to erosion is close to the actual total erosion in the furnace. Results from this analysis indicate that there are possibly more than one arc present in the crater, in which case less than 40% of the total erosion would be due to the arc, the rest is chemical erosion.

Jan 1, 2007

By M. R. Madhav

The ultimate pullout capacity of single batter piles has been presented in literature in three contradictory trends. These trends are: the pullout capacity of a single batter pile increases, remain almost constant, or decrease with increasing the inclination angle of the pile. The present paper presents a theoretical study which explained these trends in terms of existing initial stress condition and the earth pressure coefficient at rest. The paper also presents a form of guideline for predicting the pullout capacity of inclined piles based on simple field and/or laboratory tests.

Jan 1, 2010

By K Palmer

Alluvial platinum was recovered during gold mining operations in Maud Creek, a tributary of the Howard River. Average electron probe analyses give Pt 88.75, Fe 5.27, Ir 0.70, Os 1.06, Pd 0.34, Ru 0.14, Rh 1.29, Cu 1.06. Rare grains of a Pt-Fe-Cu alloy are also present and an unusual feature of all grains is the relatively high rhodium content which finds expression in segregations of rhodium arsenide, cherepanovite. Platinum is found in the Orepuki area of Southland, where it is probably partly derived from the mafic rocks of the Longwood Complex. Rocks of the Rotoroa Complex, similar to those of the Longwood Complex, form bedrock in Maud Creek and are possibly the source of the Howard platinum. Alternatively, it might be derived by glacial transport from the Matakitaki ultramafic block 30 km to the southwest. Origin from the Rotoroa rocks is preferred as, if the Matakitaki rocks are part of the Dun Mountain Ophiolites, they might be expected to contain osmiridium rather than platinum. The ratio Pt:Ir-Os has been widely used to distinguish low Pt:Ir-Os ophiolitic from high Pt:Ir-Os gabbroic assemblages. Mafic complexes such as Longwoods, Darran, Rotoroa, and Riwaka might be expected to show similar high&nbsp;Pt:Ir-Os ratios and be targets for platinum exploration. Detrital platinum examined from the Parapara area, Golden Bay is mainly osmiridium, with rare grains of rutheniridosmine, very similar in composition to that found in concentrates from the Kaniere dredge, West Coast.

Jan 1, 1987

By Kazem Oraee

Falls of ground have historically been the main cause for fatalities in underground mines. Although recent advances in technology have reduced the number of such accidents, when failures occur they usually result in severe consequences. Risks of rock falls, use of heavy machinery and electrical apparatus, entry to confined spaces, working in noisy and dusty environments, and working on unstable platforms are some of the hazards in ground control operations. Managing these risks requires a management regime involving strict adherence to operational codes of practice and an enshrined culture of safety. These should be subsequently reinforced through active participation of management, systematic training, and stringent internal and third party auditing. Accident reports show that the major contributing factor in most rock fall accidents is the failure to adequately manage known risks due to the lack of a systematic process. OHSAS 18001 (Occupational Health and Safety Assessment Series) is an international occupational health and safety management standard specification to develop occupational health and safety at the workplace. This standard is intended to help mine operators control occupational health and safety risks. Addressing the requirements of OHSAS 18001 can be a complex and demanding task. A comprehensive guide for efficient and accurate implementation of this standard is provided in this paper. The discipline can be used to establish an accountable management system foreground control activities in underground coal mines. The paper also provides guidelines for preparing necessary documents, devising safety policies, procedures, performing risk assessment, and handling instructions. Finally, the paper concludes by providing a sound analytical basis in terms of the creation of a robust safety management system foreground control operations in underground mines. Full benefits of implementing an effective and systematic operational health and safety management system are illustrated. The procedure adopted and prescribed in this paper can be used in all underground coal mines where lack of appropriate ground control practices can create deficiencies in both safety and productivity.

Jan 1, 2012

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering)degree Identification of non-linear systems can be a daunting task and in the process industries the problem is complicated considerably by the presence of noise from various sources, non-stationarity of the data and intermittence, such as observed in particulate flows. Traditional methods, such as frequency analysis and linear model-ling do not handle these systems well. Similar problems arise with the application of non-linear theory developed over the last few decades, where much of the analysis depends on embedding of the data in a phase space or pseudophase space, since these methods were not originally designed to deal with noisy systems. In contrast, singular spectrum analysis is a method which can be used to identify structure and distinguish noise from important information in multivariate data, such as the trajectory matrices of time series measurements. It provides an orthogonal basis onto which the data can be transformed, so that components of the time series can be investigated individually. With Monte Carlo methods, the components can be compared with those from linear surrogate data in order to identify possibly non-linearities in the data. In this paper, this versatile technique is briefly explained and illustrated by means of case studies.

Jan 1, 2003

The Golden Cross Mine will be the first underground gold mine in New Zealand to operate since 1952. The development plans, along with the conditions and circumstances presently found in the now ongoing mine development, will be discussed as well as a brief review of planned stoping activity and stoping results to date.

Jan 1, 1991

In this study, a 3D model of the shovel motion based multi-body system dynamics in the Automatic Dynamic Analysis of Mechanical Systems (ADAMS) environment was developed. The kinematics model of the shovel was modeled as a multi-body system, which comprises the lower, upper, and the attachment mechanisms. The Euler-Lagrangian equations were employed as the computational framework to describe the dynamic behavior of the model. A virtual prototype of the shovel was built in the ADAMS software environment. This environment allows the visualization of a 3D motion of the general mechanical system and the prediction of interference of the moving components of the shovel. The numerical analysis and animation of digging, swinging and dumping motions for the shovel were performed. The superimposed display of the deployment for the shovel in three phases allows a detailed examination of the dynamic interference among assembly components. This research provides a solid foundation for further shovel dynamics performance studies. Keywords: Shovel, Spatial Kinematics, Virtual Prototype, Visualization

Jan 1, 2009

By F. Hassani, K. Moozar, J. Ouellet, P. Gauthier

"This paper describes a sudden spill of waste rock used for backfilling from a waste pass at an underground mine in Canada, thus causing a major failure/accident. The mine operator immediately launched a detailed investigation to understand the causes of this accident and develop procedures to prevent any recurrence of such events in the future. The authors from McGill University were invited to collaborate with the engineers at the mine to examine this accident. The events leading to the accident were studied, appropriate measurements were taken and samples of the waste material were collected for further testing and analysis.The field visit and the interview of the witnesses allowed the detailed documentation of the events. The sequence of events related to the incident, along with the experimental results obtained in the course of the investigation, are presented. The waste material was characterized in the laboratory with regard to its behaviour in the presence of water. This information is discussed and the failure mechanism involved in the accident is identified. Finally, the full recommendations as well as the immediate operational measures implemented by the mine to prevent the future occurrence of such events are presented and discussed."

Jan 1, 2004

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 5 Typical Input - Ouput The input data and the printed output for case 8 of the simulations (Section A.4) are shown in the following. The branch, level, node, miner and hoist numbers mentioned in the input and output refer to the corresponding numbers in Figures A-3, A-4 and A -5, The plotted ouput, already shown in Figures A,11 and A-12 is not repeated. The input data shown does not include the following simulation parameters: DTIME = 0, 05 FTIME = 130 JPLT(K) = 1 for K = 1, 2, 3 0 for other K TPLSTR = 0.0 TPLST P = 130

Jan 1, 1976

By P. J. Brereton-Stiles, M. S. Rennie, N. Singh

Ferroalloy producers are large-scale users of electrical energy, which in many countries is in short supply and increasingly expensive. Preheating and/or pre-reduction using natural gas, recycled furnace gas or coal fines have lowered the specific use of electricity, but the high energy concentration necessary for most reduction processes can be achieved only by the use of high electric currents. Most countries have insufficient electricity to supply the demands of industry and the domestic consumer, particularly during certain periods of the day and certain times of the year. The generation and distribution of electricity is a large-scale expensive business, which is financed and managed directly or indirectly by government bodies in most countries. Both economic and political imperatives determine how much electrical energy is made available to whom and at what price. In South Africa demand is set to outstrip supply within the next few years, and the local supplier Eskom has moved from a traditional demand tariff pricing structure to a time-of-use tariff pricing so as to limit peak demand usage. This will mean a substantial increase in electricity cost to those users unable or unwilling to reduce consumption during peak periods. The optimal use of the available electrical energy depends both on the process, the furnace size, the configuration and infrastructure of each plant and its cost structure. As the cost and availability of electricity is set to change dynamically, the management of the situation becomes a real time control and optimisation problem. This paper discusses some the process and operational constraints associated with low- or no-load conditions and how to manage the situation. Electrode management will be one of the key issues.

Jan 1, 2004