Search Documents

By Manqiu Xu, Andrew Lee, Frederick D. Ford, Cara Wercholaz

"Platinum-group minerals (PGM) typically occur in such low concentrations that quantitative mineralogical evaluation is difficult or impossible. The FEI MLA system used by Vale Base Metals Technology Development has been successfully employed to produce large PGM data sets that are statistically robust. The MLA Sparse Phase Liberation mapping routine produces false colored images that accurately document mineral textures, including intergrowths between various platinum group minerals and between PGMs and other tellurides and sulfides. MLA PGM search results can be used in conjunction with mineral chemistry to calculate platinumgroup element distribution to minerals and the MLA PGM images can be used to produce model grade-recovery curves.INTRODUCTIONThe platinum-group minerals (PGM) found in Sudbury area deposits have been extensively catalogued and reviewed by many authors including, but not limited to: Farrow and Lightfoot (2002), Cabri and Laflamme (1984; 1976) and Cabri (1981). The PGM list currently used has 12 minerals summarized in Table 1. As noted by Farrow and Lightfoot (2002), platinum-group minerals in Sudbury are dominated by tellurides, bismuth-tellurides and arsenides, with an absence of platinum-group element (PGE) sulphides or ferro-platinum alloys such as tetraferroplatinum - PtFe."

Jan 1, 2011

By M. N. Pathasarathi, P. A. Beck, T. J. Koppenaal

EARLIER work1 indicated that in rolled and annealed copper the volume fraction of the cube-texture component may increase on continued isothermal annealing. Merlini found2 that in rolled copper the well-known increase in the amount of cube-oriented material with increasing annealing temperature3 is concurrent with grain growth, which takes place after recrystallization is complete. It was found that both in copper2 and in aluminum4 the texture resulting from primary recrystallization, even if this is followed by some grain growth, may in general comprise, in addition to the cube-texture component, four symmetrical texture components of the general type (123)[412], i.e., components not very far from the ideal orientations of the rolling texture. The volume fraction of the cube-texture component increases on further annealing at the expense of these four components.' The present work was undertaken to study quantitatively the increase in the volume fraction of the cube-texture component in the course of normal grain growth, under varying conditions. Since the grain-gr3wth behavior of A1-Mn alloys has been already investigated in some detaiL5 an A1 + 0.8 pct Mn alloy was chosen for this work, in which the extent of normal grain growth can be effectively controlled by the inhibiting effect of a dispersed second phase. EXPERIMENTAL PROCEDURE High-purity aluminum of the following composition was used: A1 99.997 pct, Cu 0.0004 pct, Fe 0.0005 pct, and Si 0.001 pct. A high-purity A1-Mn master alloy was prepared by dehydrating manganese chloride at 500°C and reacting it with molten high-purity aluminum at 750°C in a graphite crucible.5 The Mn metal reduced from the salt by the molten aluminum goes into solution in the latter. The master alloy? containing 13 pct Mn, was solidified under conditions suitable for minimizing segregation. An ingot of the final alloy, to be used in the experiments, was per pared by melting high-purity aluminum and the necessary amount of master alloy in a graphite crucible, and by pouring the molten alloy into a graphite mold preheated to 700°C through a box containing graphite baffles designed to intercept most of the aluminum oxide films floating in the melt. The melt was then solidified by placing the mold on a water-cooled copper plate and by keeping the top of the mold hot, in order to minimize piping. The 6 1/2 in. long, 11/4-in.diam ingot consisted largely of a single crystal. Chemical analysis showed that there was little segregation from the bottom (0.83 pct Mn) to the top (0.81 pct Mn). Spectrographic analysis of the ingot showed that the impurity content remained essentially the same as that of the aluminum used. The ingot was processed so as to obtain a uniformly small grain size. without banding. The ini-tial steps of rolling in the form of a flat bar and of annealing, down through a thickness of 0.4 in., are shown in Table I. At this point the bar was cut into four sections, each approximately 3 in. long, which were processed separately as shown in Table If. The table also gives the penultimate grain sizes obtained in each section by annealing prior to the final rolling of 90 pct RA. During the final rolling the strips were reversed end to end between passes. Annealing treatments were given in a salt pot furnace, with the temperature controlled to 1°C. All annealing of section "6s" was carried out above the solvus point to avoid the formation of second-phase precipitate. The penultimate annealing was sufficiently short to give a relatively fine grain size in spite of the high temperature. Section "6L" was processed in a similar manner, except that the penultimate annealing was much longer, so as to allow considerable grain growth. Section "4" was given the two final

Jan 1, 1961

By J. Holtzhausen

"An analysis of operating costs for underground mining operations in the current global economic climate considers the financial burden for a ventilation system to be in vicinity of 30–50%. These operating costs are often overlooked by management teams in the greater scale of things when looking to save money in the procurement phase. This oversight to operational costs can be as little as the effective delivery of ventilating air to the work zone. One of the biggest opportunities for substantial savings and improvements can be realized in the selection of a quality vent duct that is suitable and fit for purpose. The key component to the selection process for quality products is a solid selection criterion that is followed during the tender process. This allows the management team to filter out unsuitable suppliers and products. The case study identifies some of the key components that were considered in the procurement and selection process for lay-flat ducting products. These included the characteristics and strength of the materials. The selection criteria also considered a ducted performance comparison that offers the best aerodynamic performance with some of the following components. • Airflow at Duct Face (m³/s or cfm), Fan Pressure (Pa), Air Power (kW or hp), Assumed Fan Efficiency, Annual Running Costs, K – Factor or Lambda, Leakage Factor, Joining Method and available Duct Lengths with weights. • Critical components considered were the current Testing standards available for: o Bursting Strength AS 4878.5, Mass AS 2001.2.13, Tensile Strength AS 4878.6, Tensile Strength AS 2001.2.3.1, Tear Strength AS 2001.2.10, Tear Strength AS 4878.7 • Other key considerations were: o Warranty Claim, Damage claims, Local storage / operations, community engagement and relationships, current testing data, previous issues, after sales service with technical assistance, etc. Hidden costs associated with product failures and operational stoppages are often not quantified during the tender process. Buyer beware. INTRODUCTION The largest constraint underground mining operations currently face are their operating efficiencies and electrical costs. The overall cost of an operations ventilation system and its components requires more focus to identify what opportunities exist to maximise efficiency and effectiveness. This tender process may not always be clearly understood and it should be broken down into fewer components to achieve quantifiable results."

Jan 1, 2019

By M. P. Tixier, F. Segesman

Explanations bused on theory and laboratory tests tire offered for certain unusual features of SP logs which may befog their interpretation, namely the "sawtooth" SP and the reduction or increase of SP with time. The sawtooth SP is frequently seen in SP recordings of thick, very permeable watcr. sands of the Louisiana Gulf Coast. Using SP data from a resistor network analog, this anomaly is explained on the basis of a thin shale streak within the sand. under which the invading filtrate accumulates by gravity segregcitiorr. The electromotive force then appearing across the shale streak gives rise to the anomalous SP. Reduction of the SP on successive logging runs Ira often been observed in very permeable sands when as indicated by the resistivity curves, the invasion depth has been reduced to practically zero. Laboratory results verify that this phenomenon may be due, to the presence of air electromotive force, across the mod rake when the fluids on either side differ in activity. Also, there is, in some cases; an increase of SP deflection on successive logging runs, because the emf initially present across the mud cake disappears as the somewhat saline water just behind the mud cake is progressively flushed out by the invading filtrate.. Field example and laboratory data are presented. I N T R ODUCT1ON Some unusual features are frequently observed on certain SP logs which make interpretation difficult. The purpose of this paper is to offer explanations of several cases of interest. All of these arc related to the conditions of invasion. The cases to be discussed are as follows. 1. The sawtooth SP anomaly which is frequently seen within the thick, highly permeable saltwater sands of the Louisiuana Gulf Coast 1. Reduction of the SP deflection from the usual sand line in very permeable sections when the depth of invasion is practically nil. As will be explained, such a reduction is attributable to a membrane electromotive force across the mud cake. 3. An increase of the SP with time just after the iormation is drilled as a result of progressive flushing of the invaded zone. FUNDAMENTALS OF SP PHENOMENA An explanation of SP phenomena must begin with the following basic ideas. 1. The SP log derives its character from ohmic potential differences in the hole produced by currents flowing through the mud.' These currents are driven by electromotive forces which are primarily electrochemical in origin. Other possible types of SP-producing electromotive forces may be disregarded for the purposes of this paper. 2. The electrochemical emf's associated with permeable formations are now understood to consist of liquid-junction emf's and membrane emf's.',' As schematically shown by thc battery symbols in Fig. 1, the liquid-junction emf, E,,,, exists at the contact between waters of different chemical activities, a,,,, (mud filtrate) and tr,,. (formation water); the shale membrane emf, lS.sn. exists across the adjacent shales whcn they separate waters of different activities. The emf's just cited are additivc in producing SP currents (arrowed circles of Fig. I). Thus, neglecting for the moment any possible membrane emf across thc mud cake, the total electrochemical emf, E,, will be given by their sum, where K,., -! K,q,, = 12 + 59, or 71 at 75 °F. In the log interpretations the SP of a thick sand (i.e.. the static SP) is generally related to the activities of the filtrate and formation water through Eq. 1. by setting the static SP equal to - E,.

By Charles Prasky

This report describes fluidized bed techniques employed by the Bureau of Mines at Minneapolis to differentially sulfatize the manganese in two samples of low-grade manganiferous ferruginous carbonate slates from the Cuyuna Range district, Minn. Suitable mechanics of operation were established. A space rate of 1.25 to 1.5 fps, a retention time of 3 to 3.5 hours, a temperature of 700° C, and a 10 percent sulfur dioxide gas in air were adequate for sulfatizing the slates by fluidization. Under these conditions the overflow product removal rate from the 4-inch-diameter reactor was 4 to 5 pounds per hour. The sulfur dioxide was used more efficiently in the two-stage treatment than in the single-stage treatment. However, approximately 80 percent of the manganese was converted to sulfate by either treatment.

Jan 1, 1963

By J. M. Uys, T. B. King

WalSH, Chipman, King, and rant' have measured the water content (as hydrogen) of actual steel-making slags. An average water content of 290 ppm was found for basic open-hearth tapping slags and 114 ppm for acid open-hearth slags. Upon equilibration of these slags at 1550°C with a 25 pct H20-75 pct Nz atmosphere, the water content increased to about 410 and 300 ppm for the basic and acid slags, respectively. Walsh et al. concluded that an acid slag was thus relatively far removed from equilibrium, and that basic slags showed a closer approach to equilibrium, with the water vapor in the furnace atmosphere. Herasymenko2 contended that these conclusions were unjustified, as the oxygen pressure used in the equilibration experiments, ;bout 5 x X atm, was quite different from that found in the furnace. Consequently, during the experiments the slag composition would have changed due to oxidation of ferrous iron. As an extension of Walsh's work and to attempt to clarify this matter, the solubility of water in a basic open-hearth slag was measured as a function of oxygen pressure. Similar measurements were also made on synthetic silicates in the "Fe0"-Fe203-SiO, system. The experimental technique has been described previously by Walsh et a1.l and Uys and King.3 Samples of the basic open-hearth finishing slag, contained in 10-cc platinum crucibles, were equilibrated at 1550°C with atmospheres of different oxygen pressure but constant water-vapor pressure, Ph~o = 0.192 atm. Calculations, as well as measurements, indicate that this figure approximates the water pressure of the combustion gases in a steam-atomized, oil-fired open hearth. Oxygen pressures in the open hearth can vary from 10"2 atm in the combustion gases to between l0-' and 10" atm in the steel bath. The former figure depends on the combustion practice and the latter on the carbon content and temperature of the bath. The oxygen pressure of the slag should lie somewhere between these extremes and is expected to be closer to that of the steel bath than that of the combustion gases. Oxygen pressures were therefore varied between 10" and 6 x l0 atm. At the lowest pressure the slag "puffed up" when quenched (indicating possible loss of water) so experiments were not conducted at lower oxygen pressures. The results are shown in Fig. 1, which includes the water content of the slag "as sampled". The results show that the water content of the slag increased appreciably on equilibration with water vapor at 0.192 atm pressure and that the water solubility apparently decreases with increased oxygen pressure. The solubilities found are comparable to those of the Li20-Ca0-Si02 system.3 Work with synthetic slags in the "Fe0"-Fe203-SiOz system was performed at 1500" C, with Ph20 = 0.192 atrn and for oxygen pressures varying between 10"2 and 10-lo atm. Samples for chemical analysis were prepared as described by Larson.4 The results are shown in Fig. 2. Some low-silica melts tested at low oxygen pressures "puffed up" when quenched and analyzed less than 100 ppm water; these results are not included in Fig. 2. The melts containing 40 mol pct silica also showed a tendency to "puff up" during the quench, when they were tested at the lowest oxygen pressure. These results indicate that, at constant silica content, the solubility of water decreases somewhat with increased oxygen pressure. The effect is, however, small considering the wide range of oxygen pressures studied. Also, at constant oxygen pressure (above about lom5 atm) the solubility increases

Jan 1, 1963

By E. Tondu

Separation Technologies Inc.’s (STI) electrostatic separation technology is a dry, continuous process for the separation of discrete particles. This high-volume process does not require any additives nor is any additional waste produced. In December 1993, STI, in cooperation with New England Power(NEP), installed an 18-t/h (20-stph) prototype electrostatic separator at NEP’s Salem Harbor plant. The plan was to convert waste streams of type F fly ash into commercially valuable products. In July 1995, a second separator was installed at NEP’s Brayton Pointplant. Fly ash feed, ranging from 6% to 25% carbon (loss-of-ignition fly ash or LOI), is separated into <3% LOI “clean” ash and sold as a portland cement substitute in the New England concrete markets.

Jan 1, 1996

By J. Henry Harden

I DESIRE to call the attention of the Institute to a new form of drawing-board trestle. With the ordinary four-legged trestle, commonly used, one has not the means of adjusting the height of the board to the draughtsman. To obviate this inconvenience, and at the same time to enable one to incline the board, I have devised an arrangement of curved and straight slots and thumb-screws, by means of which the board can be raised three or more inches, and placed at any desired angle of inclination on either side. Figures 2, 3 (Plate I) show side and end elevations of the trestle for a single board, and Figure 4 for two boards. The latter form is adapted for use in schools, or where it is desired to economize space.

Jan 1, 1874

By Peng Jiahong

With ultrasonics application during checking the large diameter cast-in-situ pile body, it is usualy applied the statistical method of probability and PSD. This paper presents a converse probabilistic-analytical method which can identify important anomalies, both strong and weak, during interfered situation. So the inhomogeneity in concrete pile may be ellectively distinguished. In order to ensure the capacity of bed rock support layer under large diameter pile, a test-in-situ is conducted to determine the compresive strength and shear force inserting rock of the support layer, so the compresive strength and modulus value of elasticity of bed rock tested will closely tally with the actual situation.

Jan 1, 1991

By Philip Lindstrom

T he Radon mine is in the north end of the Big Indian mining district in San Juan County, Utah. Hecla Mining Co. operated the mine from early 1955 to early 1964 through an operating agreement with Federal Resources, Inc. Development consisted of a 3-compartment, 690-ft shaft, 4 main levels driven on the ore horizon and a haulage level below the ore. Evaluation of physical and economic factors showed that this flat-dipping ore occurrence could be mined by a low-cost coal mining method. The value of the deposit was high and unusual pre¬miums were possible by clean mining. Complete extraction without loss of ore pillars, minimum ore dilution and high production per man were obtained by longwall mining.

Jan 12, 1964

By R G. Barker, N Mortimer

In New Zealand, platinum group metals (PGM) occur in three main geological environments of economic interest: layered mafic igneous complexes, the Dun Mountain Ophiolite Belt, and in association with placer gold deposits. Most of the layered mafic complexes with PGM potential occur in the Median Batholith. These include the Longwood (Permian), Bluff (Permian), Riwaka (Devonian) and Rotoroa (Jurassic) igneous complexes. Exploration of the Longwood Complex discovered PGM associated with gabbroic rocks. Best assays to date include a 1 m drill intersection of 1 g/t Pt + Pd and float rock with 3.0 ppm Pt and 3.3 ppm Pd. The Greenhills complex at Bluff consists of basal dunite overlain by wehrlite and gabbro. PGM occur with chrome spinel in the basal dunite and Pt geochemical anomalies have been identified associated with the wehrlite-gabbro contact zone. The Greenhills complex has some similarities to Alaskan-Ural type complexes.Reconnaissance exploration in the Dun Mountain Ophiolite Belt has identified PGM geochemical anomalies, but no follow-up work has been carried out. During the late 1800s and early 1900s, PGM were recovered as a byproduct of placer gold mining in Southland. Placer gold prospects with PGM potential include the Waiau River, deposits flanking the Longwood Complex and some Southland beaches.

Jan 1, 2002

By W. Jacobi

INTRODUCTION The radon problem concerns the radiation exposure from inhaled short-lived radon daughters and the associated risk for the induction or promotion of lung cancer. In several groups of miners which were exposed in the past to relative high radon levels during their underground work, an excess lung cancer frequency has been observed. On the basis of these findings it has to be stated that the inhalation of radon daughters is the most important radiation hazard in mining. Involved in this radon problem in mines are the difficulties to measure the individual radon daughter exposure of miners and to estimate the dose to critical cells and target tissues in the lung from inhaled radon daughters. And finally the reduction of radon levels in mines confronts us with special technical problems which are difficult to solve. Thus the setting of annual limits for the radon daughter exposure of miners alone is not sufficient to guarantee an appropriate standard of radiation safety. Of same importance are the improvement of air monitoring and the optimization of technical protection measures in mines. This has to be kept in mind for the following considerations on exposure limits. The ICRP has recommended in 1959 for the first time a maximum permissible concentration (MPC) for the occupational exposure to radon and its short-lived daughters (ICRP, 1959). This MPC in air was derived from a maximum permissible dose equivalent of 0.15 Sv (15 rem) per year to the epithelium of the large bronchi which was regarded as the "critical tissue". This old MPC-value was derived using a simplified lung model which paid main attention to the dose contribution from the inhalation of unattached 218Po(RaA) atoms. Since this time more realistic dosimetric models for radon daughters have been developed; some of these models will be presented in special papers on this conference. Furthermore in the last 10 - 20 years substantial epidemiological information on the lung cancer risk among several groups of Rn-exposed miners has become available. Taking into account these epidemiological and new dosimetric findings the ICRP has adopted in March this year new recommendations on occupational limits for inhalation of 222Rn, 22ORn and theirshort-lived daughters. This report will be published this year as ICRP Publication 32 (ICRP 1981). The recommended limits for radon daughters were derived from the basic dose and risk limits as they were proposed by ICRP in its new basic recommendations (ICRP Publ. 26, 1977). In the following this basic system of dose limitation is shortly outlined before the special recommendations for radon daughters are described. [BASIC CONCEPTS AND LIMITS] The new basic recommendation of ICRP (Publ. 26, 1977) proceed from the assumption that in the dose range which is relevant for radiation protection, the risk RT of so-called stochastic radiation effects (carcinogenic and genetic effects) in a target tissue T increases proportionally with the mean dose equivalent HT in this tissue: RT = aT HT. If several target tissues are irradiated the total individual (stochastic) risk is given by the sum of risks in these tissues: [R = ?TRT = ? T aT HT]. Thus this concept of individual health detriment takes into account the risk contribution from each relevant tissue. It replaces the old concept of the critical tissue, which neglected the exposure of other tissues. Applying this new concept a dose quantity can be defined which is proportional to the total individual radiation risk from stochastic effects. This so-called "effective dose equivalent (HE)" is given by the sum of the weighted dose equivalents in the relevant tissues: [HE = E wT HT with E wT = 1 T &apos;1] The weighting factor wT of each tissues follows to wT = aT/awB, where awB is the total stochastic risk coefficient for a uniform irradiation of the whole body. For the lung as a single organ comprising several target tissues, the ICRP recommends a total weighting factor w = 0.12 (ICRP 1977/79). This concept of risk or detriment, respectively, has important consequences. To meet the objectives of radiation protection the new ICRP-system of dose limitation is based on the following three principles: 1) The justification of practices involving radiation exposures; no pratice shall be adopted unless it produces a net benefit. 2) The ALARA-principle that all exposures shall be kept as low as reasonably achievable; this requires the optimization of the level of protection. 3) The limitation of individual exposure (annual dose limits). It is important to note that the dose limits for individuals are only one part of this system of dose limitation. Furthermore, these limits cannot be regarded as a boundary between safe and unsafe. They have to be interpreted as the lower boundary of an unacceptable exposure region. This means that in addition to the observance of these basic dose limits it is demanded to optimize the level of protection. Consequently the optimized exposure levels or the corresponding operational limits will be normally lower than

Jan 1, 1981

By R. H. Wright

This paper describes the design philosophy and methods employed in constructing the foundation elements for the Little Britain Project in the City of London. The Contract is a design and construct package for the foundations of a 3-storey basement which will be built using "top-down" construction techniques and is to be carried out by Fairclough Piling and Marine on behalf of Wimgrove Nominees. The Project includes 8000 sq.m. of diaphragm wall and barrettes 139 No. large diameter piles ranging from 900mm to 3000mm in diameter and up to 45m deep, and 9 No. cruciform barrettes for the heaviest column loads. Major factors influencing the design of these foundations include differential settlement, heave analysis and a fast track construction approach. Little Britain will provide 43000 sq.m. of space in two linked buildings which will bridge a new road joining London Wall to Newgate Street. The foundation contract is well advanced and the building is due for completion in the Summer of 1990.

Jan 1, 1989

By Pierre Rocque

The Red Lake Mine is located approximately 600 km northwest of Thunder Bay. This 545 tpd (600 tons/day) underground narrow vein gold operation is set to produce in excess of 14.8 tonnes (475,000 ounces) in 2001 at a cash operating cost below 75 U$/oz. The high-grade nature of this deposit (>55 g/t or >1.6 opt) coupled with its complex geological environment and relatively deep location dictated the choice of a very selective primary mining method, Mechanized Overhand Cut and Fill. In addition to geological challenges, mine design issues such as material handling, ground stability and requirements for yieldable ground support are also discussed in this paper.

Oct 1, 2001

By G. R. Fitterer

Trends in slag composition in acid open hearth practice, particularly the variation in iron and manganese oxides during refining, are reviewed. A procedure which is currently being used to control the refining reactions is described and partially explained through slag phase diagram considerations. In addition, the ionic nature of these slags is considered and it is proposed that silica combines with the oxide ion and forms a series of complex silicate ions. The effect of basic oxides such as FeO, MnO, and CaO is apparently additive in furnishing the oxide ion for this purpose. IT is now possible to control192 the refining of steel in an acid open hearth furnace to a surprising degree. This control has been brought about through the knowledge and use of several facts and tests. These are: 1—A planned charge analysis based on a knowledge of the type of fuel, the bath depth, etc. 2—Knowledge and control of rate of fuel input as well as its method of atomization, if any. 3—Determination of the slag fluidity. 4—Bath temperatures (use of the Pt-Pt-Rh thermocouple). 5—Periodic determination of carbon content (use of the Carb-analyzer or Carbometer). Through the use of these control methods, a heat may be made to "melt-in" with or without residual manganese and silicon. The rate of refining or carbon elimination may be controlled accurately, and the desired tapping (or "go-ahead") carbon may be approached at a rapid or slow rate according to preference and type of steel being made. Thus operating time may be predetermined and greatly reduced. Further, all of the refining can be done without any ore or other oxidizing additions, and the heat may be brought to the desired tapping temperature simultaneously with the attainment of the desired carbon analysis. This control procedure is being used in most acid plants in the United States today and has been de- scribed.&apos;, &apos; Although the slag metal relations are sufficiently well known to control the heat as stated, yet it is possible to account for only about two-thirds&apos; of the 0, which must have been used for the elimination of the carbon and other metalloids. Phase diagram studies&apos; of the slags, slag weights, the metal particle theory,&apos; ore additions, limestone additions, etc., may all be taken into consideration; yet, the mechanism of oxidation and source of all the oxygen remain to be explained. This paper reviews some of the principles upon which the control methods were based and proposes other possibilities regarding the unexplained phenomena. Old and New Acid Open Hearth Practice Some of the recent statements in the literature regarding acid open hearth operation are based on old heat data which are not typical of modern American practice. These old heat logs have been responsible for many misconceptions regarding the acid hearth practice and represent heats which do not coincide with modern methods. In recent years, American practice has been altered materially and these changes will be briefly described. Modern American Practice: A typical log of a modern American acid open hearth heat&apos; is shown in Fig. 1 which indicates that the refining time was only two hours, during which the carbon was eliminated rapidly and the bath temperature increased at a fast rate. The manganese and silicon contents of the metal were essentially eliminated and their oxides had become constituent parts of the slag at the "melt-down" period. During the course of the heat, the MnO content of the slag remained practi-

Jan 1, 1954

By Wantae Kim

In order to establish the optimized recovery process for heavy minerals from Korean beach sand, we investigated the several physical separation methods such as gravity and magnetic separation followed by mineralogical characterization. There was clear relationship between the particle size and heavy mineral content that heavy minerals were mostly concentrated in the particles below 100mesh. Gravity separation using the spiral and shaking table separators made it possible to concentrate heavy minerals by rejecting the light and coarse particles consist mainly of quartz and other non-valuable minerals. The high-intensity magnetic roll separator and subsequent induced magnetic separator were applied to fractionate magnetic particles according to their magnetic susceptibility. The content of TiO2 of high susceptible ilmenite-rich fraction was 43.98wt.% while those of ZrO2 of non-magnetic and magnetic residue were 6.78wt.% and 3.11wt.%, respectively.

Jan 1, 2006

By K. D. A. Whaley

Abstract -The Captain North Extension deposit consists of five sulfide lenses hosted in cherty and chloritic metasediment that is bounded by quartz-eye rhyolite and laminated rhyolite . Lens 2 consists of sphalerite and galena with silver-rich tetrahedrite in chert. Lens 3 contains massive pyrite, with chalcopyrite and minor gold, gradational to minor pyrite in a chloritic metasediment . The other lenses are unexplored. The sulfides occur as beds, fracture infills, and disseminated grains. Reserves are estimated at 207 555 tonnes grading 7.38% Zn, 2.76% Pb, and 91.81 g/t Ag. The deposit is isoclinally folded, dips steeply west, plunges 50 degrees south, and is faulted out to the north, where drag folding has reversed the plunge. Minor cross-faults contain talc and sericite. High sphalerite but low pyrite abundances result in poor responses to standard electromagnetic techniques. Lens 3, which contains more pyrite than Lens 2, responds better to induced polarization and allows detection. Geochemical anomalies are found in a nearby swamp and stream, but an impervious till cover inhibits the development of soil anomalies.

Jan 1, 1992

By Ahmet Gursoy

Maryland, will be the widest vehicular tunnel ever built by the trench tube method. Careful coordination and planning were required to meet the tight and fast design and construction schedules. During the preliminary design, traditional design drawings were bypassed in favor of 25 preliminary design reports representing major work breakdown structures (tasks). For each task, alternative design solutions were examined and analyzed by means of trade-off studies on the basis of engineering, constructibility, and economic considerations, thus providing an overall conceptual value engineering approach for the entire project. So far, total value engineering proposed by the contractor for Contract I I (largest contract of the project at $245 million) is less than 1.5 percent of the contract value. This is an important indication of the success of the design phase planning.

Jan 1, 1983

By Joel Moskowitz

In 1990, the United States General Services Administration (GSA) issued a contract for design and construction of a new federal court building in New York City. Mueser Rutledge Consulting Engineers (MRCE) served as Project Geotechnical Engineers. The project site is in the historic government district at Foley Square. It is surrounded by the New York County Courthouse to the west, an existing federal prison building and federal courthouse across Pearl Street to the south and southwest, an office structure to the north, and a residential tower to the east. The interior of the site was crossed by streets which have now been demapped. As with many urban sites, this site was previously occupied by tenement buildings or industrial structures demolished near the turn of the century. Remains of old building foundations were exposed during construction excavation. In addition, buried fuel oil tanks servicing the adjacent courthouse were removed and the usual assortment of urban utilities had to be relocated for the new building foundations. Ground surface elevations vary from about 4.5 to 6 m above the local Mean High Water Datum Plane.

Jan 1, 1996

By Peter Claus

In the last years, supported gold catalysts with particle sizes smaller than 10 nm have attracted a lot of attention. While gold bulk metal is rather inert in chemical reactions and, thus, is of low interest for catalysis, highly dispersed gold particles supported on oxides as TiO2 or ZrO2 show surprisingly high activities in some reactions important for the chemical industry. The oxidation of carbon monoxide at low temperatures is mainly used as model reaction to study the unusual properties of gold catalysts [1]. On the other hand, to evaluate the catalytic potential of gold, other chemical reactions which allow to control also the selectivity have to be considered. The selective hydrogenation of ???-unsaturated aldehydes to allylic alcohols is of both commercial relevance (e.g. in fine chemical and pharmaceutical intermediate production) and specific scientific interest [2]. Note that thermodynamics favors hydrogenation of the C=C over the C=O group (stronger negative free reaction enthalpy of 35 kJ/mol), and for kinetic reasons the C=C bond is more reactive than the C=O group. Thus, in the presence of most of the conventional hydrogenation catalysts, based on Pt, Rh or Pd, -unsaturated aldehydes such as acrolein and crotonaldehyde are hydrogenated predominantly to the saturated aldehydes and only to a minor extent to unsaturated alcohols. Therefore, it is desirable to find catalysts which are able to control the intramolecular selectivity by hydrogenation preferentially the C=O group while keeping the olefinic double bond intact (Fig. 1).

Oct 1, 2003