Search Documents

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores and rock minerals is constantly required to develop new means and methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes f physical separation. Thus, in 191.9, Coghill and Bonardi 31 published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/, Schwartz 5/, and Head and his associates6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and. the University of Alabama.

Jan 1, 1940

By Stephen C. Tadolini

The U.S. Bureau of Mines has developed ultrasonic measurement instrumentation capable of measuring strains and elongations on tensioned and untensioned mine roof bolting systems. This report evaluates the pulsed-phase-lock-loop and pulse-echo systems. The pulse-echo systems measure time of flight of a signal through the bolt. The ultrasonic instrument converts the measurement into elongations or stress. The most recent Bureau instrument development converts travel-time measurements directly into elongation, load, stress, and torque by simple data manipulation from the keyboard. Bolt preparation and instrument calibration are described in detail.

Jan 1, 1990

By L Besra, A. R. Prasad, B. P. Singh

The role of surface-chemical phenomena and the physical processes that participate in the dewatering of a suspension of alumina trihydrate were subjected to a systematic investigation, which has increased understanding of the influence of surface tension, contact angle and adsorption in the process. The residual moisture content of the cake can be reduced significantly through the use of surface-active agents in slurry pretreatment or as wash-water additives. The effectiveness of a particular surfactant is hard to predict from any single parameter, but is dependent on its ability to reduce surface tension and possibly to modify the solid-liquid contact angle. If scaled up to industrial operation of the dewatering step of the Bayer process in India, the use of these chemical additives could substantially improve its process economics, reducing the fuel costs for thermal drying by a much as Rs 50/t

Jun 21, 1905

A recoverable uranium resource, shown to be suitable for in situ leaching, was discovered at Honeymoon in South Australia in 1971. Exploration of the deposit was carried out during the period from 1973 to 1979. Uranium mineralisation occurs in a coarse-grained unconsolidated sand aquifer located in the Yarramba Palaeochannel at a depth of approximately 110 m. Following initial development during 1979 to 1983 and the construction of demonstration leach facilities, the Project was put on hold. Southern Cross Resources purchased the Project in 1997. Government approval was received in March 1998 for the operation of on-site demonstration leach and recovery facilities while an Environmental Impact Statement was prepared and a 1000 tpa commercial production plant was designed. The Environmental Impact Statement (EIS) was released in June 2000 and operation of the test facility was completed in August 2000. Acceptance of the EIS by Commonwealth and South Australian state governments was announced on 20 November 2001. A Mining Lease was granted over the area of the proposed ISL operation on 8 February 2002. Operation of the Project is entirely dependent on using highly saline underground water resources to supply process and human needs. The management of discharge streams from the plant by re-injection was approved. The Honeymoon demonstration plant was the first adaptation of the solvent extraction process to highly saline in situ leach solutions. As such, it incorporated a number of unique operating and installation features. The trial period enabled optimisation of the process chemistry, additives and management and serves as an invaluable base for the proposed plant design and future operation. This paper discusses the nature of the uranium occurrence, the effect of saline water on the leach process and equipment, project design and environmental considerations, the requirements for disposal of discharge streams to minimise the impact on the arid environment and the requirements for rehabilitation following project completion.

Jan 1, 2002

Review on Some Research Methods of Mineral Crystal Chemistry and Computer Simulation on Flotation

Sep 13, 2010

By F. Hassani, R. Mikaeil, B. Ferdowsi

Two analytical solutions for estimating the ovaling deformation and forces in circular tunnels are widely used in engineering practice, due to soil-structure interaction under seismic loading. This paper discusses the discrepancy between the two analytical and finite difference methods. A comparison of the two analytical methods shows that the calculated forces and displacements are identical for the condition of full-slip between the tunnel lining and ground. However, the calculated lining thrusts differ by an order of magnitude when considering no-slip between the tunnel lining and the ground. The analytical solutions are compared to numerical analyses of the no-slip condition using the finite difference method to validate which of the two methods provide the correct method. To achieve the goal, numerical modelling, field data of the Kuhin railway tunnel and Manjil earthquake characteristics are used. Numerical analysis results agree with one of the analytical solutions that provides a higher estimate of the thrust on the tunnel lining, thus highlighting the limitation of the other analytical solution.

Jan 1, 2008

By W. Hume-Rothery

IN recent interesting papers,1,2 Bardos et al. have described ternary Laves phases of the type A2(BsSi) and A4(B5Si3) where A = titanium vanadium, niobium, and so forth, and B = manganese, iron, cobalt, or nickel; other more complex formulae have also been established. In these phases, silicon plays the part of the smaller B atom of a Laves phase AB2, and the interatomic distances show that the effec- tive silicon radii lie between 1.16 and 1.21Å, and are thus very much smaller than the metallic radius of silicon for CN = 12. It does not seem to have been pointed out that these small atomic radii are almost the sape as the normal covalent radius of silicon (1.174Å). If, therefore, silicon acts as an acceptor of electrons as suggested by Bardos et al.,1 it appears to do so, not by the building up of a negatively charged silicon ion which would be large, but by the formation of what are very nearly or may be actually normal covalent bonds. Since a covalent bond contains two electrons, its formation would reduce the number of electrons available for bonding in other parts of the structure, and in this way the effect of silicon in stabilizing the o phase at high electron concentrations might be understood.

Jan 1, 1965

By Carl Hendricks

Aquila Mining Systems Ltd., is the world leader in drill monitoring, control and GPS-based machine navigation systems for the mining industry. This paper will review the design and application of AQUILA’s drill monitoring, control and positioning systems currently in use throughout the world and some of the benefits that derive through their use. In 1993, AQUILA became the first company to install a high precision, cm level, real-time GPS receiver on a blasthole drill. In fact, this was likely the first application of GPS on any form of production mining equipment. To date, AQUILA has installed over 90 GPS based drill monitoring systems worldwide. Since 1992 AQUILA has continued to lead in the advancement of new technologies for drilling including real-time geology recognition and automated drilling control systems. The AQUILA DMseries drill systems offer mines the ability to collect and transmit to the mine office; drill production statistics, ore and waste intersections, exact collar elevations, hole positions and depths, maintenance information and consumables tracking. Unique office software developed by AQUILA provides an encompassing Windows environment within which to manage and coordinate all aspects of data communications and information management between the drills and various mine departments. AQUILA and Caterpillar, along with Mincom and Trimble Navigation are partners in a technology alliance that is providing the surface mining industry with vehicle tracking and navigation systems for all mobile production equipment.

Jan 1, 2000

By I. Marklund, W. Hustrulid

Sublevel caving is likely to remain the dominant system at both Malmberget and Kiruna for the foreseeable future. The sub-level interval has increased from 12 m in 1983 to 30 m, requiring more effective drifting and the development of a contour blasting technique to reduce requirements for rock reinforcement. Production drilling is mainly by hydraulic hammers or water-powered in-the-hole machines drilling 115 m diameter holes. Loading operations are undertaken 7 days/week with 15-25 tonne capacity electric shovels. Production has increased by nearly 70% since 1983 and productivity has risen threefold

Dec 1, 1995

By Dennis E. Jensen

Field studies were performed during blasting operations for strip coal mining above the room and pillar workings at Jenny mine in eastern Kentucky. The study is part of the Bureau of Mines program to develop criteria for the proximity of surface blasting to underground mines. Measurements and observations were made to identify physical changes in the mine. No change in the frequency of roof falls or any other indication of apparent damage was noted. Recordings of blast induced vibrations were made using sensors on the roof and floor of the underground mine and at the ground surface. A maximum particle velocity of 17.5 in/sec was recorded on the mine roof. The vibration data were analyzed and comparisons were made between roof vibration levels and those recorded on the mine floor and at the ground surface. Results are compared with previous blast vibration studies. Recommendations are made for further study toward developing criteria.

Jan 1, 1979

By Frank W. Harris

The strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chcniical and physical considerations, t,he high conductivity required for copper wire in the clcc-trical industry generally precludes the possibility of obt,aining tensile strength through the use of alloys. Consequently, this strenglh is largely a rnatter of the ~hysical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., arc matters of prime importance. The experiments described here have becn carried out dl~ring the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigat,ion of sorne of the questions mentioned above, with the object of studying thc physical ~t~ructure of hard drawn copper wire and the influence of ccrtain factors on t,hat st'ruct.ure. The work has been of an exploratory nature, rather than con~prehensivc., but it was thought that the result,s might prove of sr~fficient general interest tjo warrant their publicatlion. The bulk of the hard drawn coppcr wire used in places where strength is an important factor is rnanufacturcd to strict specification, based USU-ally in the United States on thab of t,he Arrlerican Society for Tcst'ing Materials (B-1-23). This specification calls for almost as high a, valuc of t,ensilc strength, consistent with elongation, as it is possible pract'icnlly to obtain, and only physically perfect mlaterial can be relied on to lliect such a specification. Obvious defects, such as laminat'ions protluc:etl through fins in bhe original rods or brittleness duo lo ovt~rdrawing, arc. usually recognized and need only passing refercncc. Laminatlions can be detected by twisting and untwisting the wircx several times; they will show up on the surface in the form of fins. Pig. 1 shows a very bad example of this defect. Thc wire may bc perfectly smooth before twisting hut, when such larrlinations arc3 prcstmt they will readily show up under this treatrncnt. This trouble is caliscd by sirriilar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which thc wire in Fig. 1 was drawn.

By R. C. Hall

We are pleased to confirm some of the mechanical data presented by Dr. Detert on the 18 pct Ni marag-ing steel.15 Bar 3 in. in diam and containing 0.02 wt pct C, 18.5 Ni, 8.9 Co, 5.1 MO, 0.55 Ti, 0.05 Al, and balance iron has been examined in our laboratory. Cylinders 0.5 in. high and 0.4 to 0.5 in. in diam were cold-compressed from 3 to 40 pct reduction in height. Table VI shows some typical data; deformation in-

Jan 1, 1968

By Jan A. Nilsen

This paper describes a key element in the construction of a major project undertaken by Harbourfront Corporation in its efforts to rejuvenate the central Toronto waterfront. The Spadina Pier forms one of the two major structures of the $10 million marina complex. Completed in early 1986, the 150 metre(490 ft.) long by 43 metre(140 ft.) wide pier structure will contain a 320 car parking garage as well as providing the foundation of a 17-story residential tower and a two-story retail/commercial complex. However, the pier structure posed a considerable challenge to its developers due to the the many restrictions imposed on the site by the environmental authorities which ruled out the construction of dykes or the placing of other fill materials on the highly contaminated bottom sediments. In addition, access at the site was restricted by its proximity to the main harbour navigation channel and a grain elevator berth. The original design called for a cofferdam to form an integral part of the finished structure. However, the contractor chose to regard the cofferdam as a temporary structure and proposed to construct the pier in the dry by enclosing the 10,000 square metre(107,600 sf) site with a 450 metre(1480 ft.) long single wall steel sheet pile cofferdom 7.5 metres(25 ft.) from the final pier structure. This paper will describes the design and construction of the cofferdam. Prior to finalizing the pier design, a geotechnical investigation of the shale bedrock was undertaken as well as a small sheet pile test cell program to evaluate the feasibility of driving a Canadian manufactured cold-rolled sheet pile into the bedrock. Relying on the design parameters for the shale bedrock, Foundation designed the cofferdam utilizing a post-tensioned bipod bracing system to resist a 7 metre(23 ft.) hydrostatic head as well as the maximum wind and wave forces expected at the site. The bipod bracing system consists of diagonal H-pile raker piles and verticle pipe piles anchored to bedrock with post-tensioned anchors grouted into bedrock.

Jan 1, 1987

By R. B. Schluter

Drying and preheating (partial induration) the green, unfired iron ore pellets is a means of reducing the energy required to produce metallized pellets. The Bureau of Mines processed three magnetite and two hematite concentrates through the unit operations of pelletizing, preheating in air, and reduction to metal to determine the effects of preheating upon the properties of the metallized pellets. The pellets were prepared in a 16-inch-diameter laboratory balling drum. Preheating and metallization were carried out in an externally heated 4-inch-ID by 4-inch-long stainless steel drum using air for the preheating atmosphere and lignite char as a reductant. The results 'varied considerably: two of the magnetites spalled when preheated in air at temperatures of 900° C and above, and the third magnetite and the hematite flotation concentrate required complete induration at 1,300° C to produce satisfactory pellets. The earthy hematite ore yielded excellent pellets at all preheat temperatures.

Jan 1, 1972

By Y. Ichihara, H. Matsumoto, K. Itakura, H. Eguchi, G. Deguchi, K. Sato

Mechanical data from a rockbolt drilling machine, such as torque, thrust, revolution and stroke, are useful for understanding the geological and geomechanical conditions around roadways and hence selecting the optimum bolt type and density. Laboratory experiments showed that the level of torque or thrust reflects differences in rock type, with separation of strata and cracks appearing as a specific pattern. Algorithms of neural networks based on adaptive resonance theory and back-propagation were used to extract the pattern and estimate the location of discontinuities. For field testing in an underground coal mine, a prototype data acquisition system was attached to a portable drilling machine. Several sets of logging data from one locality were combined to construct a two-dimensional model of the strata, from which the slope angles of discontinuity faces could be estimated

Jun 19, 1905

By Benjamin A. Allou

La seule production de columbo-tantalite réalisée en Côte d?Ivoire est effectuée dans les éluvions et alluvions du gisement d?Issia, localisé au Centre- Ouest de la Côte d?Ivoire. Même si un lien direct avec les roches granitiques est suspecté, aucune attention particulière n?a été accordée à l?étude de la minéralisation primaire en relation avec l?évolution des granites et des pegmatites associées. Ces granites, qui sont en intrusion dans les roches sédimentaires du Protérozoïque inférieur, comprennent : le granite orienté à deux micas (Lobo), le granite orienté à muscovite dominante (Bitapia) et le granite porphyroïde non orienté à muscovite dominante (Issia). Les résultats de cette étude indiquent que les pegmatites à Nb-Ta-Be-Li sont liées au granite de type Issia. Les observations de terrain et les analyses sur roche totale des granites montrent que: (1) les trois principaux granites de la région sont de type- S et peralumineux dans leur composition, (2) ils ont été formés pendant la période tardi- à post-Éburnéenne, (3) le granite d?Issia fut le dernier à se mettre en place. Les pegmatites liées au granite d?Issia ont été classées en quatre types : Apegmatites stériles; B- pegmatites à Be; C- pegmatites zonées à Nb-Ta-Be; et Dpegmatites zonées à Be-Nb-Ta-Li. Les pegmatites zonées comprennent les zones suivantes: I- zone à aplite; II- zone graphique; III- zone à albite, microcline, béryl et columbo-tantalite; IV - zone à microcline massive; V- zone à quartz. Ces pegmatites présentent une zone d?altération métasomatique externe. La minéralisation de Ta, Nb et Be est liées à la zone III des pegmatites de types C et D, et celle de Li est associée aux greisens qui peuvent être observés n?importe où dans les pegmatites de type D. Les données de terrain et de laboratoire indiquent que le granite d?Issia est la roche parentale des pegmatites à éléments rares de la région. Les pegmatites minéralisées sont distribuées seulement autour du granite d?Issia et les patrons des terres rares des granites et ceux des pegmatites à éléments rares sont très similaires. Les analyses de la composition totale montrent un lien génétique entre le granite d?Issia et les pegmatites à éléments rares. Il est suggéré que les pegmatites ont été formées durant le transport et la cristallisation fractionnée du magma.

May 1, 2003

This report summarizes a study conducted by The Service Bureau Corporation for the Bureau of Mines. Evaluations reflected herein are the result of an independent investigation by The Service Bureau Corporation of methane considerations during coal mining. The study is oriented toward a systematic analysis of methane control problems during coal mining. Throughout this study an attempt has been made to ensure considerations consistent with the recently enacted Federal Coal Mine Health and Safety Act of 1969. References to reports by The Bureau of Mines and others are made for the purposes of establishing identification between the evaluations contained in this report and on-going research efforts.

Jan 1, 1970

By Loren R. Anderson

This is an Appendix of Volume I. In contains the results of the electric cone penetrometer soundings from the second phase of the testing program.

Jan 1, 1982

By E. D. Calvert

The objective of this research was to examine variations in melting and forging practice for four titanium-base alloys and to determine their effect on the resultant product. Of particular interest was the evaluation of the skull-casting technique. The data should serve as a guide to producers and consumers of titanium products. Physical properties of four titanium-base alloys in ingot form and in sheet form were evaluated and correlated, where possible, with variations in the melting and casting procedure. Consumable-electrode melting was used throughout, but arc current and furnace backfill pressure were varied, and ingots were formed both by melting directly into a water-cooled copper mold and by skull melting followed by pouring into a graphite mold. Alloying metal additions for the alloys tested were (1) 8 percent manganese, (2) 6 percent aluminum and 4 percent vanadium, (3) 6 percent molybdenum and 2 percent aluminum, and (4) 16 percent vanadium and 2.8 percent aluminum.

Jan 1, 1962

By S. Malhotra

Processes for the recovery of manganese contained in low-grade domestic sources are evaluated. Conclusions are based on analysis of literature, technical evaluation and cost analysis. The Nossen Nitric Acid Process, the Sulfuric Dioxide Process rind the Ammonia Leach Process should be developed further as they offer the hunt opportunity for commercialization.

Jan 1, 1984