Search Documents

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong Operational Readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.The road blocks encountered are often from systems that one assumes will operate without trouble such as air-conditioning, or design assumptions that were taken years earlier in feasibility process stages, namely the capacity of existing systems that will connect the new plant to the existing facilities. The challenges associated with rectifying these issues in addition to the requirements to properly start-up and operate a new plant without impacting production are great, and it is imperative to have the necessary resources to react quickly to any problems.IntroductionCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary by-product of the process."

Jan 1, 2016

By S. Sun

The equilibrium distribution of Cu, Fe and Ni between Cu-Ni-Fe mattes and Pt alloy was measured as functions of the sulphur partial pressure (pS2), oxygen partial pressure (pO2),temperature and Fe content of the matte. The distribution ratios of Cu, Fe and Ni between matte and alloy were independent of oxygen pressure when the pS2was fixed at 2.5x10-5atm and pO2was varied between 10-15and 10-12atm. The distribution ratio of Cu, Fe and Ni increased as the sulphur partial pressure increased. The Cu and Ni distribution ratios decreased with increasing temperature and the Fe distribution ratio increased slightly over the temperature range of1350?1500°C. For mattes where the proportions of Cu and Ni were kept constant, the distribution ratio of Cu increased as the Fe content in the matte increased. The Fe and Ni distribution appeared to be independent of the iron content in the matte and had a value of 1.2 and 1.6 respectively. The activity of Cu, Fe, Ni in the matte was calculated using a regular solution model for solid Pt-Fe-Ni-Cu alloy. The activity coefficient of Cu, Fe and Ni decreased as pO2and pS2increased.The activity coefficients also appeared to be independent of the Fe content and temperature over the range of 36 to 54 wt% iron and 1350 to 1500°C respectively. Keywords: activity, alloy, matte, thermodynamics

Jan 1, 2004

By L. E. Cardwell

This publication contains routine analyses and related source data for 390 natural gas samples from 22 States and five foreign countries. Of this total, 385 samples were collected during calendar year 1969. The remaining five analyses are of samples collected during previous years, but releases granting permission to publish the results were not received until 1969. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 576.4 Eleven previous publications have presented the results of 8,660 gas analyses made by the Bureau of Mines Helium Activity prior to 1969. The first three, Bulletins 486,6 576,6 and 617,7 contain analyses and related source

Jan 1, 1970

By K. P. V. Lei

The Bureau of Mines investigated molten-salt electrorefining as a practical method for reclaiming vanadium from vanadium scrap. An electrolytic process utilizing a KC1-LiC1-VC12 electrolyte at 615° C was developed for producing ductile vanadium with a purity over 99.9 percent. The recovery of the vanadium in the cell feed ranged from 88 to 93 percent with a current efficiency from 83 to 95 percent.

Jan 1, 1967

By Lars G. Olavson

A prototype roof bolt which can be remotely placed by pumping has been developed by the Bureau of Mines. It is known as the "Pumpable Bolt". With the objective of field testing the effectiveness of the pumpable Bolt roof support system a mining machine was developed capable of installing Pumpable Bolts in the normal production cycle of a typical underground coal mine. The machine was built and the pumpable Bolt concept tested and evaluated as a total system in shop and mine tests. The machine was operated in the mining cycle of two mines and pumpable Bolts were installed at both mine sites.

Jan 1, 1976

By David H. Carlson

The paper presents background information including data on diesel exhaust pollutants, amounts produced and standards, a desscription of mine characteristics that affect air monitoring techniques and a review of portable measurement techniques and instruments for gas and particulate matter sampling. A general review of the laboratory and field research being conducted at Michigan Technological University in the area of diesel emissions is presented. The facilities involved with this research are also described. These are the Experimental Mine, the diesel dilution tunnel test cell, the Mine Air Monitoring Lab (MAML), the portable instruments and the production mines used.

Jan 1, 1979

By Collin L. Stewart

The high cost and limited flexibility of modern longwall systems has resulted in the need for mine engineers and geologists to predict possible adverse mining areas ahead of mining and to then design and implement suitable ground control solutions in a timely and cost effective manner. Therefore, over the last 30 years, geo-technical evaluations for coal mine planning and development have advanced from a minor afterthought to an important part of today?s successful, high capacity, longwall mining operations. The latest iteration in this progression of improved analysis for predicting future mining conditions is a computer-based Stability Mapping System developed by West Virginia University. This system is designed to allow the mining engineer and geologist to effectively combine the mine geologic characteristics, stress influences, and structural features into an integrated stability map for use in mine planning and support design. This paper details the application of the stability mapping system to Bowie Resources, LLC, Bowie No. 3, multiple-seam longwall coal mine. At this mine, the prediction of adverse mining conditions using the stability mapping system allowed management to accurately adjust their support densities and operational procedures, and to successfully mine through difficult conditions safely and successfully.

Jan 1, 2006

By Brendan Donnelly, Lasitha Piyathilaka, Jung‑Hoon Sul, Sanghyun Jeong, Benjamin Probyn

Premature failure of armoured face conveyor (AFC) chains due to corrosion is a significant proportion of the unplanned downtime experienced on longwall equipment. The AFC chains are constantly in contact with water and wet coal. The premature failure issue of AFC chains has become more prominent since the introduction of longwall top-coal caving with its additional AFC. Reverse osmosis (RO) is a popular water treatment method for reducing salinity and dissolved solids, but its impact on the corrosion of the AFC chains is unclear. This study has been commissioned to investigate the direct effects of RO water on the corrosion of AFC chains. An immersion test was carried out using AFC chain steel submerged in two water samples: untreated dam water and treated water from an RO treatment plant. Elemental analysis was conducted for both water samples, and four corrosion indices were measured for both water samples. The RO water more vigorously dissolves calcium carbonate scales leading to increased corrosion of the AFC chains although the dam water has much higher levels of calcium, chloride, sulphate, sodium, and magnesium. Bicarbonate ions are the main alkaline factor of water that provides the buffering capacity to acids. Decreased alkalinity without balancing other ions in water causes high corrosivity and decreased scaling tendencies.

Oct 16, 2023

By Wilbur I. Duvall

This report presents experimental data on crater formation in four rock types. From an analysis of these data a general theory of rock breakage by explosives is deduced. This theory accounts for most of the rock breakage and other phenomena that occur when a concentrated charge is detonated in a drill hole near a free surface. From instrumented crater tests and high-speed motion pictures of the explosions, various experimental checks on the deduced theory of rock breakage are made. The general mechanism of rock breakage by explosives as described in this report is outlined briefly below. The detonation of the explosive charge creates a high gas pressure in the charge hole, which in turn generates a compressive strain pulse in the surrounding rock. This compressive strain pulse travels outward in all directions from the charge hole. Near the charge hole the amplitude of this strain pulse is sufficient to cause crushing of the rock. However, as the strain pulse travels outward its amplitude decays rapidly until no further crushing of the rock is possible. The compressive strain pulse continues to travel outward until it is reflected by a free surface. Upon reflection the compressive strain pulse becomes a tensile strain pulse. As the strength of rock in tension is much less than in compression, the reflected tensile strain pulse is able to break the rock in tension, progressing from the free surface back toward the shot point. In other words, the rock is pulled apart, not pushed apart.

Jan 1, 1957

The Leuna Factory of the I. G. Farbenindustrie A. G., situated near Merseburg, is the biggest heavy-chemical plant in Germany and produces a very wide range of products, mainly based on hydrogen or hydrogen and carbon monoxide. Its principal products are ammonia, synthetic petrol derived from the hydrogenation of brown coal, and synthetic alcohols made from hydrogen and carbon monoxide. The plant was first, visited on April 21, 1945, by a team including E. Cotton, V. Haensel, E. B. Peck, P. K. Kuhne, H. M. Weir, L. L. Hirst, W. W. Odell, G. U. Hopton, H. Hollings, J. F. Ellis, and H. G. Simpson. It was again visited on May 8-24, 1945, by a combined British and American team consisting of R, Holroyd, M. A. G, Banks, D. A. Howes, A. J. V. Underwood, R. A. Taylor, W. F. Faragher, H. Schindler, and J. G. Allen. This team was later joined by J. F. Ellis and R. J. Morley. A third visit with particular reference to catalyst manufacture was made by W. F. Faragher and W. A. Horne, and the notes of these latest investigators have been taken into account in preparing the report. This report was edited by Dr. R. Holroyd.

Jan 1, 1946

By F. Freme

Coal production in the United States increased in2004 by 36 Mt (39.7 million st) to end the year at 1 Gt(1.11 billion st), according to the U.S. Energy Information Administration (EIA). This was a 3.7-percent in-crease from 2003’s 971.6 Mt (1.07 billion st) (Table 1).(All percentage change calculations are done at the short-tons level.) Although U.S. coal consumption rose in 2004, not all coal-consuming sectors had increased consumption for the year. Coal consumption increased in the electric power sectors by 1 percent and declined slightly in the other industrial sector, while coking coal consumption dropped by 2.4 percent. U.S. coal exports rose for the second consecutive year, while coal imports again increased to record levels. Coal stocks declined during the year, as electric generators used their stockpiles to helpmeet increased demands and missed shipments. Coal producers used their stockpiles to supplement their production levels.

Jan 1, 2005

Phase I of U.S. Bureau of Mines contract H01220S3, "Improved Sensors and Fire Control Systems for Mining Equipment, II was an investigative effort involving study of the fire problem and preliminary design of a fire protection system. Overall contract objectives included three basic efforts: * Identify problems * Develop a design * Demonstrate a system The first two efforts were conducted during the period June through November, 1972. Phase II will involve testing of system components; construction and testing of a mockup; and demonstration of the system on a truck to prove its effectiveness under actual operational and environmental conditions.

Jan 1, 1972

By Seshadri Seetharuman

The present paper summarises a series of measurements of the interaction parameter of oxygen in liquid copper with respect to a third element, e(M)o, where M is Mn, Zn, As, Se or Te which are common impurities in the liquid metal. The technique employed was the solid electrolyte galvanic cell method. The cell used may be represented as Pt, W or cermet / Cu-O-M // ZrO2 - CaO // AO, A /PT where AO/A represents a suitable oxide/metal reference. The measurements indicate that Mn and Zn interact very strongly with oxygen in liquid copper while, in the case of arsenic the interaction parameter is nearly zero. The behaviour of the elements Se and Te is unique with respect to oxygen interactions in copper bath. At oxygen levels, xo= 10-4 ? 10-5, the apparent interaction parameters are negative, comparable to that for sulphur. On the other hand, at lower oxygen levels, the results indicate that the interaction parameter values are positive. The results are discussed in the light of some of the theoretical models for solute interactions in liquid metals.

Jan 1, 1993

By J. Ouellet

"ABSTRACTA brief background on in-situ testing of mine backfill, as well as pressuremeter testing is briefly described, and results from an in-situ testing on paste backfill are presented. A series of self-boring pressuremeter tests were done from the top of a backfilled stope in an underground mine. The tests were conducted along a 20-metre vertical line in the centre of the stope. Some 14 tests were performed along this depth. The instrument used was a Camkometer built by Cam Insitu, Cambridge. The instrument proved to be efficient and reliable for underground testing in a cemented paste backfill. The testing program was conducted within the planned schedule with a high success rate. The test done in this study permitted the measurement of paste backfill strength, stiffness and in-situ horizontal stress within the backfill. RésuméUn bref historique des essais in situ dans le remblai minier est présenté. L’essai pressiométrique est décrit succinctement et des résultats d’une campagne d’essai dans un remblai en pâte sont présentés. Un programme d’essais au pressiomètre auto-foreur a été réalisé à partir du sommet d’un chantier remblayé sous terre. Les essais ont été réalisés le long d’un ligne vertical d’environ 20 mètres pour un total de 14 mesures. Le Camkometer de la firme Cam Insitu de Cambridge a été utilisé. Cet instrument s’est avéré efficace et fiable pour tester le remblai en pâte cimenté sous terre. Le programme d’essai s’est déroulé à l’intérieur de l’échéancier prévu avec un taux de réussite élevé. Ces essais ont permis de déterminer la résistance, la rigidité de ce remblai ainsi que les pressions in-situ prévalant dans le remblai."

Jan 1, 2000

By Ray Schmidt

When your committee approached me for a talk on "Mechanics of Secondary Metals Collection," I replied that this subject would probably not be very interesting to a group of engineers and requested permission to dwell on the Westinghouse Salvage Setup. I will attempt to avoid duplicating the points covered by Mr. Bliven. The Westinghouse Electric and Manufacturing Co. has main manufacturing Divisions in 25 cities and 9 different states, scattered throughout the country, as well as Naval Ordnance Plants in two midwest cities, and a Merchant Marine Turbine Plant, and two special War Production Plants in Eastern cities. You can, therefore, see that we must have a well rounded pro- gram with the entire respect and sponsorship of the various Division Managements. That was not so easy to get. Management has been a great deal like the general public in the past. I am sure most of you can remember the not very ancient day when each town had a ragman who had a horse and wagon and went through the streets of the town, from door to door, picking up what scrap he could accumulate. He was known as a junk man, and indeed, with the exception of the very last few years, the attitude of manufacturing management was: "We have a job to do. We have a product to manufacture. We don't have time to bother with the junk business."

Jan 1, 1943

By Alfred Petrick

This study gives an analysis of the copper system byproducts and discusses the identification and classification of byproduct metals and their supply systems. Arsenic, platinum-group metals, silver, gold, selenium, tellurium, molybdenum, rhenium, uranium, aluminum, magnesium, and byproduct copper, lead, and zinc from complex ores are covered. The report describes several metallurgical systems, the marginal and incremental products costs of byproduct subsystems, industry structure and organization, and the historical data on price, consumption, and supply. Supply curves are presented for about one-half of the byproduct metals studied. The study develops a conceptual framework for analysis by reviewing the present concepts of byproduct supply and the related price theory. It gives the sources of supply of the individual byproduct metals to indicate the importance of the byproduct supply to the total supply. Mills, smelters, and refineries processing byproduct materials for their metal content are identified by geographic location and company ownership, The study also includes information on the reserves-resource base supporting byproduct output, reserve estimates, and the demand aspects of each byproduct metal.

Jan 1, 1973

By B. Yarar

Samples of coal from an adit in the Fording River District of British Columbia showed hydrophilic properties between depths of 0-24.5 meters and was naturally hydrphobic at higher depths. Laboratory experiments indicated that weathered samples (i.e., those mined at 0-24.5m) could be upgraded by froth flotation at pH<2 following slimes removal. The i.e.p. of samples varied regularly between pH=1.6-4.1, the weathered fractions being at the lower end of the pH scale. These values followed a pattern comparable with the flotation behavior of samples. A patchwise structure for coal surfaces determining the resultant disjoining pressure, which in turn determines flotation-non flotation relationships is postulated.

Jan 1, 1982

By Yaxiong Wang, Yong Li, Yuedong Wu, Haigang Dong, Jiachun Zhao

A roasting-leaching process has been developed for concentrating platinum group metals (PGM) from a PGM-containing ferroalloy. The optimized roasting conditions used a NaOH-to-ferroalloy mass ratio of 1.2 at 600 °C for 2 h. The roasted product mainly comprised Na4SiO4, NaFeO2 and Fe2O3. The iron oxide and sodium silicate associated with the roasted product were leached in water and dilute sulfuric acid solution, while the PGM was concentrated in the acid-leached residue. A PGM concentration of 23.4% was obtained with assaying, and the concentration factor of PGM from the ferroalloy to PGM concentration was greater than 9.

Jun 14, 2021

By A Watson

We tend to overestimate the volume of water used to process ore and the evaporation from tailings and heap leach stockpiles. During mine operation, a significant portion of the water collected from onsite water management systems is consumed and recycled by ore processing and lesser portion discharged to the environment. When mining and processing cease, however, the mine site water balance is altered and the real effort and cost associated with managing and disposing of excess mine-influenced water becomes evident. As these flows can no longer be recycled and may not be suitable for discharge to the environment, the cost of dealing with them can comprise a significant portion of the post-mining liability. The problem of dealing with large volumes of mine affected water has the potential to become worse in the future due to the established trend of lower grades which require more water per unit of mineral processing. As a result, future mines may be expected to have greater water needs and problems than we experience today.This paper discusses various aspects about how water usage changes when a mine transitions from operation to closure based on observations and numerical simulations of made with site-wide water balance models. The intention is to provide general considerations for mine operations in planning for end of mine life and post-mining care and maintenance.

Jan 1, 2009

By Costa

The fly-in-fly-out (FIFO) mining model has significant implications for the industry as it plays an important role in fulfilling the economic, social and workforce needs of the contemporary mining industry. It has increasingly been adopted in countries such as Canada and Australia, but is the current nature of the FIFO model challenging the place women have achieved in the mining workforce? Research in the mining and oil and gas industries reveals that major sources of stress for fly-in-fly-out mining workers are the times of parting and of reunion, the challenges in defining roles within the family, parenting, and conflict between spouses over the use of the leave time and money. So how are women in the industry coping with the FIFO schedules and consequent intermittent relationship with families and partners? How is the mining industry adapting to recruit and maintain female employees in FIFO operations? This paper describes an exploratory study conducted in Canada, which intended to provide some initial insights that might help us answer the questions above. There are several inferences made from this exploratory study. It is clear that FIFO poses significant challenges for both female and male workers. It is largely seen as rigid, extremely challenging for employees with young families and workers who are single mothers, and it is generally incompatible with starting a family and caring for small children. FIFO creates severe stress on relationships and on workers psychological well-being. It seems to be indeed harder for women, since they are often in lower paying positions and therefore have less financial reward for the FIFO lifestyle. On the other hand, FIFO creates the opportunity for young women, including Aboriginal women, to jump-start their careers, as well as opportunities for mature women to work while pursuing other personal interests during their time off. This paper concludes with recommendations to improve the FIFO system in order to increase the ability of mining companies to hire and retain women

May 1, 2006