Search Documents

By Junji Shibata

Through-hole copper plating is performed to make a multi-layer printed circuit board. The through hole plating is first carried out by Pd catalyst treatment, followed by copper non-electric plating. The amount of Pd catalyst used in one plant is about 0.25-2 m3/month (8 g/dm3 PdCl2 base) depending on the plant scale, and the cost of the catalyst reaches 17,000¬I35,000 US$/month. In this study, the flow and material balance of a Pd in Pd catalyst treatment process was investigated. About 60% of Pd catalyst adheres on the through-hole and other part of setup, while 25% is released into the washing liquor. Pd in the washing liquor should be collected by a suitable method like a pressure filtration using diatomite. The material balance of Pd in Pd catalyst treatment process and the recovery method of Pd from waste solution containing Pd catalyst was investigated.

Jan 1, 2003

By Christopher Gammons

In developing countries throughout the world, gold ores are being processed by mercury amal-gamation, a technique long banned in the U.S. - unless a retort operation is used for mercury recovery - due to mercury toxicity and its effects on the environment. Amalgamation is a simple process that involves contacting a ground, slurried concentrate or ore with mercury in a slightly agitated vessel, usually for several hours, The amalgamated mercury is separated by gravity and then filtered through a fine cloth to collect the gold amalgam as a sponge, which is then fired to remove the final remnants of mercury and produce high quality gold. However, in Peru and other developing countries in South America and throughout the world, tailings are simply discarded into uncontrolled drainages and ponds and the sponge is fired in the open air. Clearly, in this case, environmental friendly and, to make matters worse, is typically conducted by family members of all ages without proper protection. Furthermore, the technique is inefficient, yielding approximately 50% gold recovery. For the past two years, faculty members from Montana Tech in Butte, MT, USA and the Universidad Nactonal del Altiplano in Puno, Peru have teamed to study the La Rinconada Mine Complex located in southern Peru approximately 100 kilometers north of Lake Titicaca and 25 kilometers west of Bolivia. The mining complex is over 5,000 meters above sea level and exists at the foot of a receding glacier in the Andes Mountains. A suite of soil and water samples collected in 2001 documented extensive Hg contamination in the Rinconada area [1]. The present paper summa¬rizes a follow-up investigation in July-2002, in which water samples were collected at numerous locations along the 200 km length of the Rio Ramis, from the Rinconada mine com¬plex to Lake Titicaca, In addition, we report new results of Hg analyses of fish from Lake Titi¬caca, The results of this study have relevance to safety and health concerns for the miners as well as people in downstream communities.

Jan 1, 2003

By P. Kim, M. Tangstad, T. Larssen, R. Kawamoto

The reduction rates of MnO and SiO2 were investigated for various charge compositions. The empirical activation energies of MnO and SiO2 reduction from SiMn slags were calculated between 1500 and 1650 °C under CO atmospheric pressure. The amounts of metal produced at different temperatures were compared, and the Arrhenius plots were described for each slag A, slag B and synthetic slag, which shows that the raw material have significant influence on the reduction rate. The rate of Mn-produced in slag A was faster than slag B despite of the relatively lower driving force. The lower rate constant in slag B implies that other kinetic factors, such as viscosity, affects the reduction rate. The estimated activation energies of MnO were 920, 304 and 975 kJ/mol MnO for slag A, slag B and synthetic slag, respectively. The rates of Si-produced were similar and slow for all slag types. However, the different activation energies of SiO2 between industrial ores and synthetic materials implied that the trace elements can have catalytic effects toward SiO2 reduction in SiMn slags. The estimated activation energies of SiO2 reduction were around 800 kJ/mol for slag A and slag B.

Mar 1, 2017

By E. Gratz, U. Pal, A. Powell, S. Pati, J. Milshtein

"The solid oxide membrane (SOM) process has been used at 1150 'C to produce magnesium by direct electrolysis of its oxide. Magnesium oxide is dissolved in a molten CaF2-MgF2 ionic flux. An oxygen-ion-conducting yttria-stabilized zirconia (YSZ) SOM membrane separates the cathode and the flux from the anode. During electrolysis, magnesium ions are reduced at the cathode and Mg(g) bubbles out of the flux into a separate condenser. The flux has a small solubility for magnesium which imparts electronic conductivity to the flux. The electronic conductivity decreases current efficiency of the process and also degrades the YSZ membrane. This study investigates different methods for reducing the electronic conductivity of the flux due to magnesium solubility. One effective method shown here is inert gas flushing near the magnesium nucleation site. Potentiodynamic and potentiostatic experiments along with AC impedance spectroscopy are used to characterize the effectiveness of the approach.IntroductionMagnesium is the third most abundant metal in the earth's crust. Since magnesium is the lightest of all metals used for construction alloys, magnesium is the leading candidate to replace steel and aluminum in automobiles. Automobile manufacturers would like to increase magnesium content from 4-5kg per vehicle to 40-IOOkg per vehicle [I]. Using magnesium alloys instead of steel and aluminum can reduce automobile weight and improve fuel efficiency. However, in order for automobile manufactures to make this change, it is generally believed that new cost effective methods of magnesium production must emerge.One approach for magnesium production which has been shown to be effective on a laboratory scale is the direct electrolysis of magnesium oxide utilizing an oxygen-ion-conducting solid oxide membrane (SOM), this is known as the SOM process [2]. A recent study estimated that a commercial SOM plant could produce magnesium from magnesium oxide at a cost that is 40% less than current technologies [3]."

Jan 1, 2012

By Chaoying Ni, Dimitry Sediako, Prashant Karandikar, Sean Fudger

Neutron diffraction measurements were performed on steel encapsulated metal matrix composites (MMCs) in order to quantify bulk residual stresses. A coefficient of thermal expansion (CTE) mismatch induced residual compressive stress method is utilized as a means of improving the ductility of the MMCs and overall efficiency of several macro hybridized materials systems. Systems consisting of an A36, 304 stainless steel, or Nitronic® 50 stainless steel shell filled with an Al-SiC or Al-Al2O3 metal matrix composite are evaluated in this work. Upon cooling from processing temperatures residual strains are generated due to a CTE mismatch between each of the phases: steel, aluminum, and reinforcement. The analysis shows variation in the measured strain and stress results due to outer steel thickness, difference in CTE between materials, and relative position within the composite.

Mar 1, 2017

By Xiaoming Huaa

The effect of the anodic polarization on the composition and morphology of the surface layer formed on chalcopyrite during ammonia–ammonium chloride leaching was investigated. The anodic polarization on the chalcopyrite electrode was used for oxidation and dissolution of chalcopyrite, and the resulting oxidized layers were characterized by XPS, SEM and optical microscopy. The results show that oxide layers exist on the chalcopyrite surface with or without any anodic polarization in the leaching solution at ambient atmosphere. However, the composition and morphology of the layers are strongly depended on the extent of polarization. The distribution of FeOOH and Fe2O3 within the oxidized layer was inhomogeneous for the sample at the open circuit potential (OCP). The composition and morphology of the oxidized layers which were formed at anodic potentials lower than 0.3 V versus SCE were similar to those of the chalcopyrite at the OCP. At anodic potentials above 0.4 V, the oxidized layers contained many cracks, and they were fragile and exfoliated. Furthermore, the sulfide had been oxidized to sulfur species with higher oxidation states. The oxidation of the chalcopyrite seemed to undergo a cyclically oxidative process that suggested growth and spallation of oxidation layers on chalcopyrite in a layer-by-layer sequence.

By W. S. Hui, M. G. Silva-Valenzuela, H. Wiebeck, F. R. Valenzuela-Diaz, B. B. Michel

Biodegradable polymer microcapsules have been used as a control sustained release system with many applications. Studies reveal that the incorporation of nanoparticles improves matrix properties, even more so if the clay is modified. The objective of this work was to compare microcapsules of poly (succinate-co-butylenelactate) (PBSL) reinforced with Brazilian clay, composed of smectites and kaolinite, in its natural (MMT/K) and modified (O-MMT/K) forms. Nanocomposites and microcapsules were synthesized by emulsification-diffusion of solvent and solvent diffusion methods. Its characterization was then performed by scanning electron microscopy (SEM), stereo microscopy and wide-angle X-ray diffraction (XRD). The results reported corroborate that PBSL/OMMT-K form an intercalated montmorillonite and kaolinite nanostructure, capable of generating uniform spherical microcapsules with diameter values smaller than that of PBSL/MMT-K, reaching 5–10 lm. DRX indicates that there was a real change in the clay structure. The incorporation of modified clay showed an improvement in surface quality and the strength of microcapsules, making it possible to produce smaller sizes.

Mar 1, 2018

By Toru H. Okabe

As part of a systematic study on the thermodynamic properties of complex nitrides, phase equilibria of the system Li-M-N (M Mg, AI, Ga) at 900 K were investigated. An attempt to determine the thermodynamic properties of complex nitrides was made by using the galvanic cell method, which utilizes LiMgN as an electrolyte under nitrogen atmosphere. The electromotive force (Emf) of ilie cell at temperatures between 800 and 1100 K was measured. Whilc the Emf of the cell at 900 K was measured to be 0.137 V, data discrepancies of ±0.03V were found. It was difficult to determine temperature dependence of ilie Emf. The Gibbs energy change for the reaction, 113 LbN (s) + 1/3 Mg3N2 (s) = LiMgN (s), at 900 K was determined to be tJ.Gor (LiMgN) -13.2 (±2.9) kJ/mol. Using thermodynamic information on ilie binary nitride from literature, the standard Gibbs energy of LiMgN was derived to be AGO f (LiMgN)= - 121 kJ at 900 K. The thermodynamic stability range of nitride was discussed by constructing isothermal chemical potential diagrams that provide a better understanding of ilie stability region of the LiMgN phase. The diagram was found to be in good agreement with the isoiliermal phase diagram determined by ilie alloy equilibration meiliod. Although the obtained data includes large uncertainties, the results provide a better understanding of the iliermodynamic stability of nitrides. The potential application of this complex nitride to nitrogen chemical sensors or a medium for controlling nitrogen potential is also shown.

Jan 1, 2003

By Jinqian Zhao, Jiarong Li, Shizhong Liu

"Creep cavitation of in single crystal (SX) superalloy was investigated. The constant load creep tests, in single crystal superalloys DD6, were conducted at the conditions of 800°C/700MPa, 850°C/550MPa and 900°C/450MPa, respectively. It was found that there were square facets on the stress fracture surface, and microscopic cavities in the ruptured specimens in the vicinity of the fracture surface. Both the square facets on the fracture surface and microscopic cavities in the section of the ruptured specimens show the morphology of the same thing at the different views, namely creep cavities, which are take the form of flatten cuboid. In fact, creep cavities are the longitudinally tensiled creep cracks slowly growing during the stress tensiling. The factors of creep cracks nucleation and growth conditions include: (a) enough high temperature to activate diffusion (b) casting pores as nucleation origination (c) high strains and strain rates. Eventually, the instantaneous fracture mechanism of creep specimen is cleavage fracture.IntroductionFor the materials used in elevated temperature service, creep behavior has to be accounted for. It is well recognized that creep rupture in polycrystalline materials at high temperature occurs principally by the nucleation and growth of microscopic cavities at grain boundaries, followed by microscopic cavities linkage to form micro- and eventually macro-intergranular cracks[l,2]. Without the usual grain boundaries, SX superalloys have superior capabilities at high temperatures to polycrystalline superalloys, and have become an established feature of gas turbine technology where they are commonly employed in the manufacture of high performance blades[3]. A considerable amount of work has been done over the past tens of years, and many models for nucleation and growth of creep cavities have been proposed, however, those are mainly for polycrystalline materials.In order to improve creep resistance that single crystal superalloys, in which grain boundaries are removed, have been developed. Because there don't exist grain boundaries in SX superalloy, the mechanism of nucleation and growth of creep cavities must be different from that in polycrystalline materials.Understanding the formation and characteristics of creep cavitation is crucial to model the lives of single crystal superalloys.M. Marchionni and L.G. Zhao et al. found that there were square facets on the stress fracture surface [4,5]. Roger C. Reed pointed out creep cavities lie in the necked region[6]. In this paper, the effects on the formation of creep cavities are discussed, as well as the morphology of creep cavities and fracture mechanism of SX superalloys."

Jan 1, 2013

By Guanghui Li, Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Xiaohui Fan, Zhiyuan Yu

With the increase of proportion of biochar(without modified) replacing coke breeze, the physical strength of sinter decreases due to the faster burning speed of biochar. An investigation upon passivating biochar with boric acid was then conducted to strengthen sintering in this paper. A layer of thin film of B2O3 distributed in the surface of biochar was observed, which could reduce the contact between reaction gas and biochar. So the burning speed of biochar was decreased properly after passivation, and the combustion efficiency increased due to the inhibition of carbon gasification. The comprehensive effects of above changes could increase the maximum temperature of sintering bed, which facilitated to the mineralization of sintering mixtures. Eventually sintering indices got reinforced. Thus the indices of sinter as applying 40% passivated biochar were comparable with that of 100% coke breeze.

Jan 1, 2015

By Hui-Gai Li

The fine Ti oxide inclusions precipitated during solidification are favorable for intragranular ferrite nucleation. The oxygen content before solidification affects the composition and size of inclusions. The composition of precipitated inclusions in Mn-Ti alloyed steel was studied by means of thermodynamic calculation and experiment in this paper. The micro-segregation of Mn, Ti and O during solidification was considered in calculation and unidirectional solidification apparatus was employed in experiment to ensure that alloy elements diffused along solidification direction. The results showed that: inclusions are mainly Ti oxide when oxygen content is 10ppm; they are Ti oxide and Mn-Ti oxide when it is 20ppm; Mn-Ti oxide dominates when it is 30ppm. With the increase of oxygen content, the size of inclusions increases. The maximum oxides size is about 3µm from statistical results of experiment.

Jan 1, 2008

By T. Manlyama

The Tamano Smelter of Hibi Kyodo Smelting CO., Ltd. went into operation in 1972. The Flash Smelting Furnace that was originally adapted was equipped with electrodes that were attached to the settler substitute of the slag cleaning furnace. Later the development of our own original coke combustion technology was promoted and a new Tamano Type Flash Smelting Furnace (T-FSF), without electrodes, was put into operation in 1988, T he technology of coke combustion and combustion the burner have continued to improve. As a result the copper losses in the Wag have been reduced as well as a stable operation has been achieved, Furthermore; this has been accomplished while increasing the concentration feed and the matte grade. The current objective is to continue to strive for high matte grade operation and to raise production efficiency while paying attention to the important subject of copper losses in the slag. In this report, the data related to the copper loss in the slag reduction are presented along with the influence of the thickness, settling time and coke. The recent operation conditions of the T-FSF are also presented.

Jan 1, 2003

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. is carrying out a low cost production using a Tamano Type Flash Smelting Furnace (T-FSF), which is an improved version of Outokumpu Type Flash Smelting Furnace but without slag cleaning furnace and also by developing its own coke combustion technology. Coke combustion technology that is the basis of the system has been improved several times and, at present, it has evolved to a stage where it can be reproduced on the Computer guided system for Coke Combustion in the T-FSF (CCCT) using a general- purpose computer. This CCCT is featured by 'its trend control and predicting function, and an operator can freely control the operation parameters so as to control the operation flexibly. We have recently developed an overall energy reduction system covering the Smelting Plant to Sulfuric Acid Plant, which we call an Optimum Low Cost Operation System (OLCO) to reconsider the energy costs including coke, heavy fuel oil, and electric power. In this report, we would like to present the recent operation of T-FSF based on CCCT as well as the optimum energy operation utilizing OLCO system.

Jan 1, 2002

By R. Upadhyaya

Aluminium alloy matrix cast composites have been synthesised by incorporating fine graphite powders (0.5 - 20 µm size) and chopped carbon fibres (6.5 pm P). 3-6 mm length) by liquid metallurgy technique. Incorporation of these second phase materials exceeding 6-8 wt% invariably resulted in agglomeration of the dispersoids and sometimes leading to even total rejection. It was found that small additions of mischmetal (1-3 wt%) during dispersion resulted in better incorporation without much agglomeration of the dispersoid as evident from the macro and micro structures of the composites. Further, the additions of mischmetal increased the volume of the effective incorporation of the dispersoid even to the extent 50- 60%. The mischmetal addition results in a significant increase in the power factor of the stirrer motor indicating an apparent increase in the viscosity of the system. The higher viscosity of the melt increase the shear transmission conditions within the melt during stirring thereby breaking the agglomerates of the dispersoids. The increased viscosity of the melt seems to be due to the formation rare earth - aluminium inter metallics precipitation, as observed in the metallographic studies, thereby making the process a "pseudorheocasting? technique. A provisional patent has been filed based on this work.

Jan 1, 1989

By Kazuteru Tozcwa

The oxidation of several sulfide minerals in aqueous ammoniacal solution is discussed thermodynamically. The region in which Cu(NH3)2 4+ is stable has been estimated as a function of pH and concentration of total ammonia, {[NH3) + [NH4)}. In ammonia leaching when copper in sulfides is assumed to be extracted in the form of Cu(NH3)2 which will be rapidly converted to cupric ammine, thermodynamic data predict that such minerals are oxidized readily in the following order, CuS, Cu2S, CuFeS2, ZnS, NiS, Ag2S. This agrees with investigations on ammonia leaching of sulfide minerals, reported previously. The leaching of copper sulfide concentrate has been examined experimentally. Copper in a copper sulfide concentrate, in which the main constituents were chalcopyrite and pyrite, was effective¬ly extracted. The copper extraction was affected by factors such as (1) agitation intensity, (2) oxygen partial pressure, (3) NH3/Cu molar ratio, (4) leaching temperature and (5) addition of ammonium sulfate. From the results obtained in this work, it is concluded that mass transfer of oxygen plays the most important role in ammonia leaching of copper sulfide minerals.

Jan 1, 1976

By Yuanbo Zhang, Zijian Su, Bingbing Liu, Guanghui Li, Jicheng Liu, Manman Lu, Tao Jiang

Blast furnace slag (BFS), one kind of typical solid waste in the steel industry, was used as structural materials to synthesize NaNO3/BFS composite phase change materials (C-PCMs) by mixing and sintering method. NaNO3 in the composites functioned as phase change materials (PCMs) and BFS as structural skeleton to maintain a stable external form. In this study, the prepared C-PCMs could remain in the solid state without salt leakage even if operating temperature exceeded the melting temperature of NaNO3. The composition and structure of BFS and the prepared composites were characterized by XRD, FTIR, SEM and TG-DSC analyses. The results showed that NaNO3 was well incorporated in the pores of BFS. The melting temperature and latent heat of the final composites were 300.5 °C and 65.53 J/g, respectively. The product also had good thermal storage performance and durability even after 100 thermal cycles. The energy density of the product was calculated as high as 468.03 J/g for an temperature range of 50–400 °C.

Mar 1, 2018

By Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie

In the present study, the oxidation process of vanadium and chromium bearing hot metal was investigated by using CaO-FetO-SiO2 slags at 1653K in MoSi2 furnace. The results indicated that both the vanadium distribution LV and chromium distribution LCr were of the orders of 2.2~2.4 with the basicity range of 1.32~1.78 and FeO weight percent range of 28%~45%. Both LV and LCr decreased with increasing basicity and decreasing FeO weight percent. The phosphorus distribution LP was of the order of 1.34~1.56. However, LP increased with increasing basicity and decreasing FeO weight percent. The oxidation ratio values of V and Cr in hot metal were above 84% and the values of P were nearly 50%. In other words, it means the addition of CaO in vanadium slag provided a certain ability of dephosphorization along with keeping high oxidation ratios of V and Cr.

Jan 1, 2015

By A. A. Hejja

The effect of composition on electrical conductivity, viscosity and liquidus temperature of the slags was investigated in the temperature range of 1300" to 1450°C. The synthetic slags containing CaO, MgO, SiO,, A1,0, and FeO were similar to those employed in the electric furnace smelting of sulphide Cu-Ni concentrates containing PGM (Platinum Group Metals) from the Merensky Reef of South Africa. FeO and SiO, were found to affect the viscosity and conductivity the most while liquidus temperature depended on MgO content in addition to these. The activation energy for electrical conduction was found to vary from 67 to 159 kJ/mol and that for viscosity from 125 to 209 kJ/mol. Optimization of the slag composition was attempted on the basis of opposite trend of the viscosity-electrical conductivity relationship with slag composition.

Jan 1, 1994

By Adam Powell, Salvador Barriga, Matthew Earlam

"The inert anode is a key enabling technology for dramatic energy and emissions reduction in extractive metallurgy. In molten salts, the materials challenge is nearly insurmountable: the anode must conduct electrons at high temperature in a pure oxygen and molten salt environment. A solid electrolyte, e.g. zirconia, between the salt and anode removes the molten salt stability constraint, and can act as a container for a liquid metal anode. This can be liquid silver for oxygen-generating inert anodes, or several metals for natural gas-fueled anodes; it is possible to switch between these modes. The solid electrolyte brings several other benefits: it eliminates molten salt contamination of the anode gas, creates a reducing environment enabling low-cost steel vessels, increases current efficiency, and eliminates carbon contamination of the product. New developments presented here, including current collector and low-cost anode designs, amplify these benefits for producing aluminum, magnesium, rare-earths, and other metals.IntroductionReactive metals such as magnesium, aluminum and rare-earths play increasing roles in efficient transportation and clean energy. In response to new fuel economy standards, automotive OEMs are planning large increases in use of aluminum and magnesium to reduce vehicle weight. Rareearth permanent magnet motors and generators exhibit better power-to-weight and efficiency than induction motors and other designs, making this today's primary motor technology for hybrid and electric vehicles, and for wind turbines. Nickel metal hydride (NiMH) batteries with lanthanum are dominant in hybrids. In 2011, transportation comprised 28.6 out of 103.1 EJ of US energy consumption [1] and 1,845 out of 5,471 million metric tonnes (MMT = 109 kg) CO2e of US greenhouse gas (GHG) emissions [1], creating big targets for economy-wide reductions.Unfortunately processes for making reactive metals for these applications are very inefficient and heavily-polluting. In primary aluminum production, Hall-Heroult cell electricity use [2] is more than double the reaction enthalpy due to heat losses through frozen cryolite side-walls and anode gases, graphite anode plants add significant energy use and GHG emissions [2] (see Table 1). Magnesium is even worse: silicothermic reduction by the Pidgeon process in China produces about 85% of the world's magnesium using coal or coke gas [3]. Chloride electrolysis begins with high-purity MgO and requires carbochlorination or hydrochlorination and costly chloride dehydration [4]—rendered unnecessary for aluminum by the Hall-Heroult cell. Production of neodymium and lanthanum with graphite anodes leads to inconsistent carbon content: small cells make 1 kg batches for analysis, sorting and sale by carbon content, with very high labor and analysis costs. And vertical electrodes give no incentive to reduce anode effect: some reports indicate that China's rare-earth metal industry emits more CF4 and C2F6—with global warming potential (GWP) 6500 and 9200 times CO2 respectively—than China's aluminum industry [5]."

Jan 1, 2014

By Abhishek Lahiri, Animesh Jha

"A new technique for the selective separation of rare earths and impurities from lower grade titaniferous ores has been developed which will reduce the overall reduction in the energy costs, and therefore the CO2 generation by at least an order of magnitude during the chlorination and waste handling stages of TiO2 to TiCl4 reaction. The process includes roasting the ilmenite ore with alkali followed by water washing step, which removes nearly 80% of oxides of lanthanide and actinide elements present in lower grades of titaniferous minerals. In the context of preferential separation of rare- 3+ + earth and actinide oxides, we have examined the roles of Al and K ions on the lattice structures of ilmenite and complex titanate as the product layer forms during the roasting in air in the presence of potash. The composition of the mixtures of oxides derived from the separation process shows that the mixture of rare-earth oxides m ay be a high-value co-product of the overall beneficiation process.IntroductionWorldwide the production of synthetic rutile is carried out either by the sulphate or the slag-making followed by fluidised bed chlorination of TiO2 enriched slag granules. The chlorinated gas is then re-oxidized to make white pigment grade TiO2. The waste generated by the sulphate process is predominantly iron sulphate, which has limited use in the water treatment plant. The remaining wastes from the sulphate process undergo further treatment using filtration followed by evaporation and thermal decomposition after which it is disposed into deep sea. On the other hand the chloride waste is extremely hazardous and requires special case by neutralisation, followed by impoundment in a managed pond, where it is monitored for long-term for potential contamination to the soil and ground water. Rare-earth and prelanthanide wastes often end up in the pond where they are diluted and irretrievably lost for further use or recycle. Certain parts of the world the chloride process wastes are pumped via deep boreholes into porous geological strata. The present techniques of disposal are not only expensive but also pose continued threat groundwater and soil and marine life in case of sulphate waste [1, 2]."

Jan 1, 2009