Search Documents

By B. B. Agrawal

Iron ore fines is an area of concern in India. A possible avenue is to use these fines for sponge ironmaking. Work has been carried out to pelletize these fines with coal and a suitable binder, and cure them in ambient atmosphere to retain in-situ reductant. Pellets were characterized for physical strength and metallisation. Critical factors were granulometry was percentage of coal & binder. In laboratory tests, pellets got metallized faster compared to lump ore. Large-scale trials were conducted in a 12-meter long rotary kiln plant. For 90% metallization, required residence time was only 60 minutes against 240 minutes for lump ore. Coal requirement also decreased. Investigations established the fast reduction nature of pellets. This is due to reduction-reactions occurring simultaneously at many sited within the composite pellets, in addition to the diffusion of reducing gases from the surface of the pellets to its core. The developed process is a value addition in the conventional pelletmaking and is environment-friendly also.

Jan 1, 2006

By Katsuyoshi Tatenuma

"In order to mitigate the effect of global warming by preventing the accumulation of atmospheric CO2, a permanent fixation method of surplus CO2 as an insoluble mineral onto the sea bottom is proposed. As the proposed reduction method of atmospheric CO2, the concrete concept of this method is to form an insoluble carbonate mineral (CaCO3) by direct electrolysis of the seawater; Ca2++2HCO3 -+OH- ? ?CaCO3(insoluble)+CO3 2- (soluble)+H++H2O <not as coral reef reaction>, are directly disposed of itself onto the sea bottom. By this treatment, a concentration of carbonate is reduced in the section of superficial seawater, and therefore the absorption capacity of atmospheric CO2 increases depending upon the shift of chemical carbon equilibrium between the mass of superficial seawater and the atmosphere. As no additives are required, or no secondary waste are produced, the proposed method assuming as green-orientated, has possibility to resolve fundamentally the problem of global warming in a green orientate manner.IntroductionRecently, the amount of atmospheric CO2 has been exponentially increasing and it is a main greenhouse effect gas causing the global warming [1, 2]. The concentration of atmospheric CO2 has increased more than 30% (370ppm in 2001) during only last two centuries, therefore approximately 750 Gton-C of CO2 currently exist in the atmosphere, in which 180 Gton-C of CO2 are accounted for the increment during two centuries [1, 3, 4]. In order to avoid the progressive increase of CO2 global abundance, 3 Gton-C of the incrementing amount per year [4], have to be removed annually from the atmosphere."

Jan 1, 2008

By Michael L. Sorokin

The behaviour of cobalt during processing of nickel raw material is analysed within the Ni-Co-Fe-S-O-SiO2 system using the computer model. For this purpose the thermodynamic parameters for "three-suffix" Margules&apos;s equations in Co-Fe-S and Co-Fe¬Ni-O-S1O2 systems were computed! Phase and iso-activity diagrams for Co-Fe-S system, and phase diagrams for the systems Co-O, Co-Fe-O, Co-Ni-O, C-oO=SiO2 and Co-Fe-O¬SiO2 are calculated using the developed computer programs and identified parameters. The diagrams are used to analyze cobalt behaviour at smelting and converting.

Jan 1, 1995

By T. S. Montgomery

The performance of carbon-magnesia brick in electric arc furnaces (EAF) is interpreted in light of their observed optical microstructures. Features at the bricks&apos; hot faces were protruding periclase grains, metal globules, graphite-metal contacts and linear void patterns. These features were com-pared to similar features previously seen from microstructures of basic oxygen furnace (BOF) refractories. Modes of formation were sought; an attempt was made to interpret their influence related to wear mechanisms.

Jan 1, 1982

By Mieke Campforts

The usefulness of the water-cooled probe technique to experimentally study slag solidification and freeze lining formation in pyrometallurgical reactors is evaluated. With this technique a layer of solidified slag is formed on a water-cooled probe that is submerged into a liquid slag bath. The influence of the submergence time and the heat input is examined. The solidified layers are analyzed with light microscopy, electron microscopy, electron probe micro-analysis and X-ray diffraction. Thermodynamic software is used to interpret the solidification microstructure. The results demonstrate that the technique is useful to understand freeze lining formation.

Jan 1, 2006

By Sepp Härkki

The energy crisis in Finland after World War I1 together with a sharp rise in the price of energy caused Outokumpu Oy to consider replacing the electric furnace smelting of copper concentrates by some other method. The flash smelting method developed under these circumstances offered a considerable saving of fuel through the utilization of the reaction heat of sulphides and yielded a high recovery of sulphur in the form of acid. The pilot plant testing of the new process was carried out in the years 1947 - 1948. The process was adopted for the smelting of copper concentrates (1) (2) (3) on a commercial scale in 1949 and applied successfullv to the smelting of -nickel concentrates&apos; at the Harjavalta Works in 1959 (4) (5) (6). In 1962 Outokumpu adopted another type of flash smelting where elemental sulphur is recovered from the gases after the thermal decomposition of pyrite in the flash smelting furnace (7) (8): In recent years, the copper-nickel flash smelter and pyrite process have been combined to produce elemental sulphur instead of SO2 from the smelter gases (9) (10). The basic idea of the Outokumpu flash smelting process for sulphidic ores is that the conventional methods with separate roasting and smelting operations are replaced by a combined roasting, smelting and part-converting process carried out in one unit. The heat generated from the exothermic reactions can thus be used for smelting the ore so that only a small amount of additional fuel is needed. The characteristic of the method is also that the dried, fine-grained concentrate is smelted in suspension, which offers the best conditions for rapid reactions. The recovery of waste heat from the furnace off-gases had been considered already in the original flash smelting system. A

Jan 1, 1976

By Norimasa Yamasaki, Masao Kurosaki

"The effects of plating conditions on the crystal orientation of electrodeposited zinc were investigated by varying elecyrolyte flow rate and current density. Precipitation of the Zn (00 • 2) basal plane is promoted at lower current density and higher flow velocity. Effect of the flow velocity on the mass transport was evaluated based on the polarization measurement in which Cu was used as the tracer. As a result, it has been clarified that the crystal orientation of electrodeposited zinc can be uniquely arranged by the overvoltage (iU0.5) that can be simply calculated by considering -the current density and boundary layer thickness. At the same time, the electrode potential during electrodeposition that can be calculated by using a model based on the competitive reactions of hydrogen reduction 'and zinc reduction exhibits an extremely good correlation with the crystal orientation of electrodeposited zinc.Introduction Electrogalvanized steel sheet has better surface properties than hot-dip galvanized steel sheet, and is used in home electric appliance and automobile applications. Factors such as crystal morphology, crystal orientation and surface roughness have a large influence on its appliance, formability and corrosion resistance [1-3].Electrolysis, condition, bath composition and alloying elements are reported as factors that affect the crystal orientation of the electrogalvanized coating. Factors that can be controlled on time in the production site are electrolysis condition that-is current density and plating solution flow velocity.Some studies[4-6] report that the crystal- orientation of the Zn(00 • 2) plane is increased by promoting, the mass transfer of zinc ions in the plating solution or decreasing the concentration overvoltage, but did not investigate in detail the plating solution flow conditions in the plating cell nor quantitatively determine the effects of both current density and plating solution flow conditions on the crystal orientation of ' electrodeposited zinc."

Jan 1, 2000

By Larry Southwick

This Peirce-Smith Converting Centennial symposium is celebrating the contributions of two men, William Peirce and E.A.C. Smith, in advancing technology allowing the copper industry to realize its full potential. However, theirs is representative of a larger story: New, simpler technology releasing the stranglehold of older, more complicated technology, new developments in vessel configuration and design finding alternate routes around dead ends in operability, advances in technique and concepts removing roadblocks of cycle time and capacity, and overall innovation opening up vast new reserves around the world to those companies willing to embrace those improvements. Our story is also one of personalities, stubborn smeltermen versus the innovators, those inside the industry versus those from outside. It is a story of an initial borrowing from the steel industry, but also Peirce and Smith, from the refining end of the copper business, taking the ideas of Baggaley from Pittsburgh’s steel and airbrake industry, who built on what Hollway, Manhès and David, Douglas, and others had done in smelter tests, further to compete with the previous primacy and closely held expertise of the copper smeltermen in Wales. These advances have been well recorded in photographs taken over the last 150 years. A number were submitted especially for this symposium. Many others were published in the mining and metallurgy press of the times. Several mining schools also retained copies of photos either taken during field trips, or donated to the school by alumni and operating companies. This presentation will provide a selection and discussion from these sources of “converters in action”, describing the various designs, operations and developments depicted. The focus here will be on the first roughly 60 years of copper converter development, from Bessemer’s days at the dawn of this new idea, up to and slightly past the time of initial adoption of Peirce and Smith’s designs.

Jan 1, 2009

By Baozhong Ma, Qian Li, Yonggang Wei, Shiwei Zhou, Bo Li, Chengyan Wang, Hua Wang

The magnesium-rich nickel oxide ore (w (Ni) =1.09 %, w (MgO)=29.08 %) mixed with 6 % and 8 % anthracite were roasted at different temperatures. XRD and SEM/EDS techniques were utilized to characterize the phase and microstructure transformation of the ores. The results show that lizardite and chrysotile of raw ore were converted into forsterite and enstatite during reduction roasting process. Simultaneously, iron and nickel oxide were reduced and migrated from the initial magnesium silicate. Fe3Si were formed when the roasting temperature went up to 1300 ℃ and 1350 ℃, and a small amount of Ni was observed in it. Temperatures got too high were not benefit to the polymerization of ferronickel.

Jan 1, 2015

By Donghai Li, Cheng Pan, Xuyang Liu, Xuewei Lv, Chenguang Bai

"Fine chromite ore is the common raw material to produce ferrochrome alloy through the submerged electric furnace process. The electric resistivity of fine chromite ore plays an important role in the operation efficiency because it determines the current distribution. The effect of particle size and the contact area of the particles on electric resistivity for several of chromite were investigated at room temperature, and the relationship between the electric resistivity of mixed particles and the volume fraction of lump ore to fine ore was also studied. The results shown that the electric resistivity increases with the increase of particle size, and the electric resistivity of mixture decreases with the increase of volume ratio of fine ore.IntroductionChromium is one of the most important alloying elements in manufacturing of stainless steel that used at high temperature and corrosive environment applications [I, 2]. As the raw materials to be charged into the steel, ferrochromium alloys and charge chromium are produced directly by smelting of chromite ore with the reducing agent in submerged electric arc furnace (SAF). During the process, the oxides of chromium and iron were reduced by carbon and meanwhile the electrical energy were consumed [3,4]. The ideal industrial process is to achieve high recovery level of Cr and Fe with minimal power consumption. In SAF process, the electric resistivity of charge stock has significant effect on the current distribution, which determines the heat distribution, molten bath structure and chemical reactions in the furnace. High resistance of the charge is desired to reduce the current distribution through the charge stock, thus the electrodes may insert into the charge stock with proper depth to form a high temperature arc heat source, and proper smelting can be realized[5]."

Jan 1, 2012

By I. Gaballah

Decontamination of synthetic solutions of PbC12 containing 10, 100 and 1000 ppm of lead, using chemically treated barks had been studied. The percentage of !cad cations&apos; removal from solutions depends upon the pH and the initial concentration. About 99 % of the initial lead content can be removed at pH of about 3.5, 5.5 and 6.5 for initial concentrations of 10, 100 and 1000 ppm respectively. The maximum retention capacity of the treated bark is about 83 mg of lead per gram of modified bark. Bark loaded with lead had been analyzed by Infra Red spectroscopy. It seems that lead reacts with hydroxyl groups of the phenolic constituents of the bark. On the other hand, the removal of a lead cation by the bark leads to the release of two H+. This seems to show that the removal of lead could be interpreted as an ion exchange with hydrogen belonging to the hydroxyl groups of the modified bark.

Jan 1, 1994

By Shuqiang Guo, Xionggang Lu, Yuyang Bian, Weizhong Ding, Lan Jiang, Kai Tang, Changyuan Lu

For recovery of rare earth elements from the NdFeB based permanent magnet scraps, a high temperature process was used. Permanent magnets scraps were firstly oxidized in air. The optimal oxidation conditions under air are at temperature of 700oC holding for 30min. After the oxidation process, the oxides were reduced by graphite crucible at 1500oC under Ar atmosphere. By this way, the rare earth elements were recovered in the form of oxides, and Fe was separated to the metal phase. Boron distributed in both the rare earth oxides (REO) containing slag and the metal phase. In order to reduce the boron contents in the rare earth oxides, the carbon saturated iron bath and NdFeB added carbon saturated iron bath were used to refine the slag. By this process, the rare earth oxides with a comparatively high purity of 98.2% were gotten.

Jan 1, 2015

By Merete Tangstad, Eli Ringdalen

"In Norway ferrosilicon/silicon and ferromanganese production are strong with world markets of 4 % / 9 % and 4 %, respectively. Research and development in the academia mirrors the national interest; hence, there has been extensive academic research in these areas. There are some vital drivers and premises for a successful cooperation between the academia and industry with the main driver being a win-win situation for both. For industry,the potential advantages include cost-, competence- or environmental- benefits; for academia, the important drivers are building of competence and equipment, educating more students at higher levels, and increased possibilities to publish. In Norway, the benefits of cooperation between industry and academia are basic knowledge regarding thermodynamic and kinetic data, as well as reaction mechanisms within core processes. In recent years, such research interests have focused on the depletion of raw materials as well as environmental issues.IntroductionIn 1989, the Norwegian Ferroalloy Producers Research Association (FFF) was funded on the belief that a common research association would benefit the industry by making it easier to perform basic research as well as paving the ground for better recruitment to the industry. The funding partners in Norway were the FeSi/Si and FeMn producers. Today, the producers are Elkem, Finnfjord, Fesil, Wacker, Eramet and Vale. The main research partners working with FFF are SINTEF (Materials and Chemistry) and the Department of Material Science and Engineering at the Norwegian University of Science and Technology (NTNU). With more than 1700 employees, SINTEF is the largest independent research organization in Norway and NTNU is the largest technical university. Together, the two organizations provide an exceptionally strong materials technology research environment, and especially so for pyrometallurgical research."

Jan 1, 2012

By Zhongliang Tian, Yun Cheng, Yexiang Liu, Ming Jia, Yanqing Lai

"A fundamental electrochemical study of Si ions in Na3AlF6-LiF melts and electrolysis using liquid cathodes was conducted. Cyclic voltammograms (CVs) clearly showed the depolarization of silicon deposition on liquid cathode by forming chemical complexes with the liquid solvent metals. Besides, co-deposition of Al and Si is possible when Si ions are insufficient in the molten salt. Based on the electrochemical results, silicon diffusion into liquid cathode is modelled and evolution of Si activity with concentration is deduced by a mathematic approach. Electrochemical study using liquid metals as working electrodes, can be used as an alternative approach for the acquisition of basic data on alloy behavior. Galvanostatic electrolysis showed that liquid cathodes are appropriate to collect the deposited solid silicon and the highest collection efficiency is almost 85%.IntroductionRecent years have witnessed an increasing demand for solar-grade silicon (Si) by the photovoltaic industry [1-4]. The preparation of high-purity metals through electrolysis and electrorefining offer many advantages such as low cost, low-energy consumption, and environment-friendly process, and thus has been widely used worldwide. From the perspective of electrochemistry [5-7], by utilizing the electronegativity difference between the impurities and Si and controlling the relevant process parameters, it is possible in principle to electrodeposit monatomic Si from a Si4+-containing compound melt. Moreover, because the carbon content of the high-purity Si obtained through electrolysis can be effectively controlled and used as a very ideal raw material in the preparation of electronic-grade and solar-grade Si, the preparation of high-purity Si through electrolysis has received widespread attention [8,9]. Monnier et al. [9] used a graphite electrode to obtain high-purity Si (99.9 %-99.99 %) from Si02/Na3AlF6 system through electrolysis; however, because the Si was precipitated in a solid form and showed poor conductivity, the deposition rate was too slow. Olsen et al. [10] obtained high-purity Si films via electrodeposition in K2SiF6/KF-LiF system by selecting electrode materials with high surface quality (such as Ag and graphite). However, in order to ensure the film quality, the deposition current density must be relatively low (10-50 mA/cm2), resulting in a low current efficiency and low deposition rate, which are not conducive to reducing energy consumption and applying to practical use"

Jan 1, 2014

By Anish Kumar

Keywords: Ultrasonic velocity, Poisson?s ratio, Elastic constants A new correlation has been established between two independent elastic properties, ultrasonic shear wave velocity and Poisson?s ratio, in a wide variety of isotropic solid materials, such as pure metals, ceramics, polymers and intermetallics. It has been shown for the first time that Poisson?s ratio decreases with increase in elastic moduli, E & G and ultrasonic velocities. This new correlation between two independent elastic constants may lead to the reduction in independent elastic constants for isotropic solid materials from two to one, at least for a given alloy system with different microstructural conditions.

Jan 1, 2005

By Shengli Wu, Yuandong Pei, Zhixing Zhao, Shuhai Ou, Jiangshan Shi, Huaiying Ma, Jun Xiong

Spraying technology on sintering surface bed after ignition has become a hot research topic, with the purpose of achieving energy-saving, emission reduction and improvement of sintering indexes. In this paper spraying steam technology was researched from theory, experiment and practice. First of all, from the thermody- namic and kinetic analysis, the mechanism of sintering surface spraying steam was analyzed and its advantageous effect was con firmed. Based on this, sintering pot test and commercial trial were carried out respectively. The results shown that spraying steam is bene ficial for increasing coke combustion ef ficiency with improving CO 2/(CO+CO2) in the exhaust gas from 80% to about 85% level, through decreasing CO content of flue gas by more than 1000 –2000 ppm. There was a suitable spraying amount to improve the quality of the sinter, and the spraying position of the steam cannot be excessively front and rear. Due to the low steam pressure (1 kg) and temperature (about 100 °C) compared with industrial steam (3 kg and 130 °C, respectively), the sinter quality such as yield index was affected by spraying steam in sintering pot test to a certain extent, and proper spraying amount (0.008 m 3, 50 kg sinter) in sinter pot test is far smaller than application amount in commercial trial (2t/h). It is thought that suitable spraying steam parameters has a comprehensive effect of energy saving and quality improvement.

Mar 1, 2018

By W. E. Wallace

Rare earth elements combine with most, of the metallic elements. As early as 1971 over a thousand intermetallics had been identified and described(1) From a magnetics viewpoint, systems involving. the d-transition metals Fe, Co and Ni are particularly interesting. In these systems there are at least four significant interactions: R-R exchange (R - a rare earth), R-T exchange (T = a transition metal), R-R exchange and the crystal field interaction acting upon the. rare earth ion. There is complex interplay between these interactions leading to bewildering variety in their magnetic behavior., Because of this and in view of the commercial significance of some rare earth intermetallics, studies of these systems has been an unusually active area of inquiry for the past two or three decades. The large magnetic moment of many of the rare earths, viz., 10 µB per atom for Dy and Ho, 9 1B for Tb and Er, etc., attracted, attention many years ago to the rare earths as potential ingredients for alloys to be used in permanent magnet fabrication. The utility of a permanent magnet in high perform¬ance devices (travelling wave tubes, voice coil motors, brushless motors, etc.) is in large measure determined by its maximum energy product, (BH)max. [(BH)max is the maximum value of B (magnetic induction) and H in the 2nd quadrant of the hysteresis loop.] Enhanced atomic moment in princple can lead to increased B and a large maximum energy product. Until about 1970 the largest (BH)max value known was about 5 MGOe(mega-gauss Oersted). This was for A1NiCo - an alloy involving Al, Ni and Co. It was recognized that the rare-earths had the potential for much higher energy product; in the case of Dy the theoretical energy product is about 35.0 MGOe., 70 times that of Alnico. (Needless to say, this theoretical value has never been achieved.) Large-scale efforts began about 30 years ago to synthesize magnetic materials containing rare earths and which would be suitable for permanent magnet fabrication. It was recognized by Strnat(2) et al. that a material to, be useful in high energy magnet fabrication would have to satisfy three. criteria:

Jan 1, 1992

By Lifeng Zhang

Printed circuited boards contain considerable quantities of valuable metal, while also containing many environmental pollutants making them unsuitable for landfill. In this study the decomposition of common plastics used in printed circuit boards were studied. Polytetrafluoroethylene (PTFE), polyvinyl chloride (PVC) and polyethylene (PE) were heated in both C02 and argon atmospheres using a thermo-gravimetric furnace (TG) coupled to a mass spectrometer (MS). Soda ash Na2C03 and baking soda NaHC03 were used as reactants. The degradation temperatures and evolved gases are presented for single plastics and mixtures. Mixed plastics are shown to behave as a sum of the individual plastics. The mass loss temperature is the same in CO2 and argon. However, less residue is formed when heated in CO2.

Jan 1, 2008

By Hideki Minoura

"Two novel electrochemical techniques for the preparation of highly crystallized CdS film have been presented. One is cathodization of a conductive substrate in an acidic chemical bath containing cadmium salt and thioacetamide, where electroreduction of proton at small current densities induces a growth of highly crystallized CdS thin films, whose growth is not disturbed by the reactions in the solution phase. The other technique is electoreduction of aqueous Cd2+— SCN complex. An advantage of this technique lies in no formation of solid particles in the bulk, of the bath.IntroductionIn recent years much attention has been paid to materials preparation by solution processing because of its advantages in lowering the cost as well as the stress to the environment, as compared to the conventional gas phase techniques which unavoidably require high temperature and/or vacuum. We have been trying to explore novel techniques for preparing functionalized compound semiconductors by aqueous solution process. Semiconductors which we have been mainly focusing on are CdS and ZnO, which are important semiconductors finding applications in various devices. In the present paper, some of the techniques that we have recently established for the preparation of highly crystallized CdS will be presented.Methods of the CdS film processing in solution phase (wet process), which have been reported so far can be divided into two major groups; one is chemical bath deposition (CBD) in alkaline solution containing Cd2+ and thiourea 1)4) and the other is electrodeposition (ED) in acidic solution containing Cd2+ and thiosulfate ions - 5)-8) or organic solutions containing dissolved sulfur 9)-11)."

Jan 1, 2000

By M. El Ganaoui, P. Bontoux

"A computational model to investigate solid/liquid phase change transitions for binary alloy under directional solidification is presented. Conservation equations are developed by using an homogeneous formulation. A second order accuracy method of time and space based on finite volume approximation has been evaluated by comparing results to spectral solution for time-dependent solutal convection developping in a melted alloy. For extended model to solid/liquid interface effects time amplification of solutal perturbation injected near the interface is described before considering solutal convection is melt.IntroductionThe enthalpy method gives a front fixing approach for energy equation without introducing coordinate transformation. The interfare position is recovered a posteriori [1]. A number of authors have extended this approach so as to include the convection phenomena within the two phase 'mushy region' [2, 3, 4, 5, 6].We have developed a time-dependent enthalpy-porosity formulation for directional solidification [4, 6, 8]. The interaction between solid and liquid phases is modelised by a Darcien type force in the phase change area. The behaviour of the melt is similar with the flow of an incompressible fluid in a porous medium. This force is proportional to the relative phase velocity. It corresponds to a damping force depending on the anisotropic permeability of the 'mushy zone'. The permeability depends on the liquid fraction and on the size of·solidification microstructures. An informative discussion of a new slant on the general approach of continuum mechanics needed to analyze the formation of mushy zone is given in [12]. The method is extended to the presence of species diffusion: the solutal Stefan condition which expresses the solute incorporation or rejection across the interface is accounted implicitly in a species equation valid in all the domain [14, 15]."

Jan 1, 2001