Search Documents

By Sergio N. Monteiro

Fibers extracted from the ramie plant have been traditionally used in textile and are now being considered as polymeric composite reinforcement owing to their superior strength. Recently the mechanical behavior of ramie fiber reinforced polyester composites was investigated but no significant improvement was found. Therefore, the objective of this work was to carry out a similar investigation by changing the type of polymeric matrix. Specimens with up to 30% in volume of ramie fibers incorporated into epoxy were bend-tested until fracture. The results showed a moderate improvement with a tendency of decreasing stress for higher amounts of ramie fibers due to the weak interface developed with the epoxy matrix.

Jan 1, 2009

By Jie Li

Series of carbon compounds as anode materials were prepared for super lithium ion capacitor using graphite and active carbon (AC) as raw materials. Their electrochemical properties were investigated by constant current charge-discharge test. The results showed that the compound anode had good capacitive performance as well as Li-ion battery performance. The potential of the capacitor could be as high as 3.5V vs Li/Li+ when compared with 2.5V vs Li/Li+ in the AC-AC capacitor, accordingly, the energy density increased from 21.7Wh/kg to 40.3Wh/kg. The compound anode also had excellent rate performance that as the current density increasing from 0.1A/g to 1A/g,the capacitance decreased only 1.3F/g, and good cycle performance that the capacitance holding remained 96.7% after 10 times cycles even at the highest potential of 3.5 V vs Li/Li+.

Jan 1, 2009

By Min Chen, Cui-huan Huang, Zhen Tian, Jian-hong Dong

"The present work studied the production of Fe-Si-Mn alloy from adjusted converter slag by thermodynamic analysis. The results showed that solubility of SiO2 in the molten slag increased with increment of temperature, and it is about 80% at 1800 ?. With increment of SiO2 content, a(MnO) and a(CaO) decreased, and a(FeO) increased to the maximum when w(SiO2) is about 30%. As a result, the reduction of the slag was in the order of Fe?Mn?P before SiO2 reduction, the reduction order was Fe?P?Mn?Si when SiO2 content in the slag was from 46.4% to 54.2%, and changed to Fe?Si?P?Mn when SiO2 content exceeded 54.2%. The mass fraction of Si in the alloy phase increases with increasing of w(SiO2) in the slag, and the mass fraction of Si in the alloy reached to 62.2% at 1800 ?.IntroductionFerroalloy production is a high energy consumption and high pollution industry[1-2]. If ferroalloy production could be produced from molten slag by addition of carbon-reducing agent, the valuable metal and oxide in the slag can be recycled, most importantly, if the high-temperature resource carried by molten slag can be made full use in the field of ferroalloy production, the power consumption of ferroalloy production could be cut down greatly.Converter steel slag is a kind of byproduct in steelmaking processing increasing rapidly with the increment of crude steel, but the utilization ratio is low. Most heat recovery research is still in the experimental stage except the heat recovery of blast furnace slag by water quenching method, at present[3-4]. It is of great significance for enterprises to energy saving and emission reduction if the molten steel slag could be utilized directly. Not only the reuse methods of liquid steel slag material can be promoted, but also the use of heat carried in the slag could be achieved. The basicity of converter slag is high and the activity of SiO2 is low so the reduction of SiO2 in the slag is little. The compositions of slag and metal phases were calculated by Factsage program on different conditions to explore the reduction of converter slag for recovery of valuable metals and an efficient new way to use the high-temperature heat combining with the current reuse and research status of converter slag. Further, the improvement of components activity in slag and the increase of Si concentration in the metal were also dicussed."

Jan 1, 2012

By Carlos M. Fontes Vieira, Ruben J. Sanchez Rodriguez, Carlos E. Gomes Ribeiro

"In this study we attempted to model a response surface for the apparent dry density of ternary blends of calcitic marble particles. The crushed marble was divided into three granulometric ranges. Simplex network methodology was used to determine the mathematical relation between granulometric ranges and apparent dry density (ADD) of particle mixtures. A highly significant regression was obtained and the simplex network methodology proved to be able to predict high packing particle compositions.IntroductionProblems with packing and expected porosity of particles are common and widely recognized to be important in terms of both fundamental physics and engineering applications. For example, densification of a powder mass is important in the shaping of solids in ceramics, powder metallurgy or composite synthesis; chemical processes such as solid-liquid separation (sedimentation, thickening and filtration), raw material handling (stockpiling, blending, drying, storage and transportation) and pyrometallurgical processes (agglomeration, coke making, ore sintering, blast furnace iron making and new iron making processes) [1,2].Many factors can affect particle packing, but in practice, there are three main factors: (dimensionless) particle size distribution, particle shape and absolute particle size [2].Geometrical and practical methods were developed to predict properties in mixtures. Zou, Gan and Yu [2] present a paper treating a prediction of the porosity of multi-component mixtures of cohesive (fine) and non-cohesive (coarse) particles. Bahiense et al. [3,4] used a simplex network to determine a mathematical model for obtain the optimal compositions between aggregates to a greater packing of a ternary particles mixture. Despite these techniques for predicting particle packing, some studies in particulate composites production don't present clear criteria for choice of particle distribution [5,6]. As the best particle packaging depends on the size, distribution and shape of these particles, individual models can be constructed for specific combinations of these factors."

Jan 1, 2014

By A. V. Tarasov

In order to improve the efficiency of hydrometallurgical processing of pyrrhotite concentrates, an integrated set of research has been carried out to investigate the use of sulfur dioxide in individual unit operations and as a leaching agent in the autoclave process as a substitute for oxygen. Treating iron-containing raw materials for production of nonferrous metals are based on the selective reaction of SO2 with iron sulfides and oxides. Iron is dissolved as sulfate, which can be treated in a separate circuit to produce iron-containing pigments or it can be disposed of after neutralization. Nonferrous and precious metals contained in pyrrhotite concentrate do not react with sulfur dioxide and remain virtually completely in the solid phase, i.e. high-grade sulfide concentrate to be treated by hydro- or pyrometallurgical methods. Elemental sulfur formed in the process of leaching is separated from the pulp in granulated form as a result of the use of special surfactants. The process of sulfide concentrate leaching with the use of sulfur dioxide is conducted at temperatures above the sulfur melting point (119°C) with distributed feeding of surfactant and under a partial pressure of sulfur dioxide of up to 0.3 to 0.5 MPa.

Jan 1, 2006

By Jamil M. Khalifeh, Shadia J. Ikhmayies, Bothina A. Hamad

"The structural and electronic properties of cubic d -NbN are investigated using density functional theory (DFT) and all-electron full potential linearized augmented plane wave method (FPLAPW). The equilibrium structural parameters are determined by fitting the total energy as a function of volume to the Murnaghan's equation of state. We calculated the total and partial densities of states (DOS) and compared them with those computed by different authors. Our DOS at Fermi level is found to be very close to the experimental value. The band structure is computed, discussed and used to find the characteristic energy separations. Valence electron density contours are recorded and discussed. We deduced the partial charge densities of different bands and binding energies of valence core levels and compared them with experimental and theoretical results obtained by different authors.IntroductionNiobium nitride has been intensively investigated over the last decades because of its interesting physical properties and technological applications (superconducting microdevices, microelectronic, catalytic probes, and hard coatings) [l]. While the group IV transition metal nitrides (TMN) mainly crystallize in the cubic NaCl structure (Bl type), those of group V and VI nitrides occur as different phases. Thus for niobium nitride, many phases have been reported in the literature: cubic fcc d -NbN, tetragonal ? -Nb4N3, hexagonal d -NbN, hexagonal e -NbN, and low nitrogen content hexagonal ß -Nb2N [l, 2].Structural and electronic properties of niobium nitride were investigated theoretically and experimentally by many authors. For example, in 1975 Schwarz [3] obtained the partial density of states for NbC and NbN from APW band structure calculations. In 1975 Kallne and Pessa [4] studied the electronic structure of Nb, NbC and NbN by using X-ray emission. In 2003 Amriou et al. [5] studied the electronic structure and bonding mechanism of NbC and NbN compounds using first principle total energy calculations using the full-potential linearized augmented plane wave method. Also in 2006 Sanjines et. al [l] studied the electronic structure of the hexagonal~Nb2N, hexagonal' d -NbN, and cubic d -NbN thin fihns by using X-ray photoemission spectroscopy. They [l] also calculated the densities of states for these phases and used them in the interpretation of the experimental valance band spectra. Most of these studies are old and there is a need for more recent studies. According to our knowledge, there are little comprehensive theoretical studies on this subject by using FP-LAPW method [5], which proved its ability to give accurate results. In this work we used the FP-LAPW method to study the structural and electronic properties of the cubic (fee) o-NbN (space group Fm-3m, prototype NaCl) crystal."

Jan 1, 2013

By Bin Xu, Qian Li, Qiang Zou, Yongbin Yang, Long Hu, Tao Jiang, Xuefei Rao

The recovery of palladium from the chloridizing leaching solution of spent Pd/Al2O3 catalyst was studied mainly by sulfide precipitation tests and chemical composition analysis. The effects of key parameters including sodium sulfide concentration, pH, addition rate, temperature, and stirring speed on palladium precipitation efficiency are systematically investigated and optimized.

Mar 1, 2017

By N. Moelans

A method using an ex-situ electrochemical measurement device was developed to determine the oxygen potential of non-ferrous metallurgical slags. The electrochemical cell consists of the molten slag sample, an inert Ir electrode, a stabilized Zr02 solid electrolyte and a NiINiO reference electrode. Different slags from non-ferrous pyrometallurgical processes were analysed at 1100 and 1200°C and pO2 values between 10-3 and 10.12 bar were obtained. The measurements were evaluated with? thermodynamic calculations and using processing considerations. It was found that the reproducibility and stability of the measurement was significantly improved by shielding the molten slag from the atmosphere by a thin layer of carbon, especially for slags with a low oxygen potential.

Jan 1, 2003

By Jilai Xue, Jun Zhu, GermainKouma Ndong, Luxing Feng

High-temperature corrosion behaviors of Fe-Ni-Cr alloy as inert anodes for aluminum electrolysis have been studied. The effect of anodic overpotential on layer growth of anodic surface is specially considered. The corrosion layers on the anodes tested were analyzed using XRD and SEM-EDS to provide a fundamental understanding of the layers growth at metallic anode surface. The dissolution of the scale layers on the metal anode occurred with low overpotential, while AlxM3-xO4 spinel phase within the scale layers was found with an increased overpotential. A mixture of multiple MyO layers existed on the anode substrate. The results may be useful for understanding and controlling the corrosion behaviors of Fe-Ni-Cr anode for potential application in aluminum electrolysis.

Jan 1, 2015

By Guy Deschênes

In spite of the wide use of lead compounds to enhance cyanidation of free milling sulphide-bearing gold ores, an industrial control method was only implemented four years ago. This study presents the results of the investigation that led to the development of the on-line control technology. Two free milling sulphide-bearing gold ores and high purity minerals were used to develop and test the concept. The first ore contains 2.8 g/t Au, 6.2% pyrrhotite, 2.1% pyrite 0.6 % arsenopyrite, 0.1% chalcopyrite and 0.1% organic carbon. The second ore contains 10.4 g/t Au, 3.2% pyrite, 0.8% pyrrhotite and 0.38% chalcopyrite. The first ore showed a much higher oxidation rate in the pre-leach than the second one and consumed seven times more cyanide. A relation between the formation of thiosulphate and thiocyanate and the additions of lead nitrate were quantified. The ?reducing power?, a titration with permanganate, predominantly determines the concentration of thiosulphate and thiocyanate in cyanide solution. The relation between the reducing power and the addition of lead nitrate at various concentrations of pyrrhotite and chalcopyrite in the ores was established, providing a monitor/control strategy for lead nitrate addition.

Jan 1, 2006

By A. Deneys

An experimental technique has been devised for studying the reaction kinetics of the reaction: ZnO + 2Fe0 = Zn(g) + Fe203, by which zinc evolution can occur from a molten slag bath in the absence of a carbonaceous reductant. When studying the reaction kinetics by heating from room temperature, solid state reactions and poorly defined melting points may obscure the starting point of the reaction. In order to eliminate this problem, an experimental technique was devised whereby two molten slags could be melted independently, and then mixed, to provide a well defined starting point from which to begin taking measurements. Two crucibles were mounted in a vertical reaction cylinder. The upper, mild steel, crucible had a bottom pouring plug which was sealed by a steel stopper rod. A fayalite mixture was contained in this crucible. The lower crucible contained an A12O3-CaO-SiO2-ZnO solution. Once the two slags had been melted, the steel stopper rod was removed from the upper crucible. The upper, reduced slag (fayalite in equilibrium with the upper steel crucible), drained into the lower crucible where the two slags were mixed by submerged argon stirring. Dip samples were taken to measure the zinc content of the final mixture as a function of time. The experimental procedure will be described, as well as results of experiments which were conducted on synthetic slags. The system investigated was similar to the lead blast furnace slag which is produced by the primary lead smelters of Missouri, USA.

Jan 1, 1997

By Hiroyuki Matsuura, Fumitaka Tsukihashi

"Emission of CO2 gas from steelmaking industry covers more than 12 % of total CO2 emission in Japan. Though many efforts have been made to curtail energy consumption and high energy efficiency of Japanese steel production process has been achieved so far, further reduction of CO2 emission is strongly requested to develop sustainable steel production process and produce “green material”. Recently, authors have proposed the innovative hydrogen production process, in which water vapor is reacted with discharged steelmaking slag to produce hydrogen gas. This reaction can be achieved without any external energy source and operated by huge thermal energy associated with steelmaking slag and FeO or unrecovered Fe droplets that are relatively rich in the slag. In this paper, thermodynamic calculation results with various initial conditions in terms of hydrogen productivity were presented. Laboratory-scale experiments were also conducted to clarify the validity of thermodynamic calculation and the reaction rate in realistic conditions.IntroductionIronmaking and steelmaking process from iron ore through blast furnace and BOF is an essential steel production route for Japanese steel industries to supply high quality steel products in large quantity to society stably. Blast furnace – BOF process requires huge amount of fossil fuels such as mainly coal, resulting the emission of considerable amount of CO2 gas. Since the emission of CO2 gas from steel industries, about 147 Mt (FY2011), accounts for approximately 12 % of domestic CO2 gas emission in Japan (FY2011),[1] it is an urgent issue for steel industries to develop environmental-friendly ironmaking and steelmaking process and reduce CO2 emission. Various kinds of gases and by-products generated from ironmaking and steelmaking processes have been recycled as much as possible at present. Enormous thermal energy is also generated from processes and released to surrounding atmosphere as various forms such as sensible heats of gases, molten steels or by-products, and as heat losses. However, these energies are not utilized before final dissipation to atmosphere. Although various technologies to utilize thermal energy from ironmaking and steelmaking processes have been attempted to develop, practical application of these technologies has not been achieved because the thermal energy is not always useful as an energy source. In steelmaking process by BOF, fluxing agent such as CaO is added during reefing and thus about 100 kg/t-steel of steelmaking slag are generated. Since the steelmaking slag is discharged at temperature range between 1873 and 1923 K after discharge of refined molten steel, it also has large thermal energy. Amount of generated BOF slag is 11.0 Mt/y (FY2012) in Japan.[2] Assuming the amount of steelmaking slag is 10 Mt/y and its average heat capacity from room temperature to 1923 K is 1 kJ/kg·K,[3] unutilized heat is estimated to be 16 PJ/y, which is equal to annual energy consumption of 420 thousand families in Japan.[4]"

Jan 1, 2014

By Fiseha Tesfaye, Pekka Taskinen

"Thermodynamics of the equilibrium phase assemblage Ago_9Cul.lS-Cu2-xS-CuS have been studied by an EMF -method. The ternary phase was synthesized from the pure Cu2S and Ag2S in vacuum furnace at high-temperature and mixed with appropriate compositions of Cu2S and CuS to form the cathode electrode. The EMF-measurements were made on the solid-state galvanic cell Pt(-) I Ag I RbAg,ils I Ago9Cu1.1S-Cu2-xS-CuS I Pt(+), in a temperature range from 316 K to 498K.Based on the measured EMF vs. T relations, thermodynamic functions (?fG° , ?fS and ?fH°) of stromeyerite (Ag0.9Cu1.1S) in equilibrium with Cu2-xS and CuS have been determined. The obtained experimental values have been compared with the available literature values. New experimentally determined thermodynamic properties of the solid solution (Ag,Cu)2Sss were determined.IntroductionDue to intense mining of high grade sulfide ore minerals in the past, recently, the available sulfide ores are poor in metals and becoming increasingly complex; such that, the production of high grade metals by the conventional pyrometallurgical processes is compromised. Consequently, smelters are in need to modify their operating flow sheets and strategies for processing more complex feed materials economically, while meeting the strict environmental regulations. To make the appropriate modifications, accurate thermochemical data of phases and phase assemblages which exist in these complex ore minerals are essential.Silver-bearing sulfosalts are encountered in ore minerals for the production of base metals and are common sources of silver. Among the silver-based sulfosalts, stromeyerite (Ag0_9Cu1.1S) is relatively common ore mineral in most hydrothermal vein and replacement deposits [1]. Recently, the ternary chalcogenide compound Ago0.93Cu1,07S has been studied, intensively, due to its high ionic conductivity and gradual disorder in the sequential phase transitions [2]. Therefore, accurate knowledge of the thermodynamic properties of stromeyerite has considerable fundamental and practical interest in many aspects of extractive, chemical and physical metallurgy."

Jan 1, 2014

By Gaifeng Xue, Lei Zhang, Aimin Duan, J. Y. Hwang, Lina Wang

"The removal of chemical oxygen demand (COD) from coking wastewater was experimentally investigated using a three-dimensional electrode reactor. The experimental results showed that the refractory organics in coking wastewater can be effectively removed by this process, and COD removal efficiency was affected by the operating parameters, such as electrolytic retention time, particle electrode dosage, initial pH, current density, aeration amount and electrical conductivity. The experimental results show that the three-dimensional electrode could have a COD removal efficiency of more than 60% and a running cost of no more than 6 YUAN (RMB)/t. This indicates the great potential of a three-dimensional electrode reactor in engineering applications as an advanced treatment methods for coking wastewater.IntroductionCoking wastewater is generated from coal coking, coal gas purification, and by-product recovery processes of coking; it is composed of phenolic compounds, heterocyclic compounds, polycyclic aromatic hydrocarbons, ammonia, cyanide, polycyclic nitrogen-containing aromatics, acyclic compounds, etc. Most of these constituents are refractory, poorly biodegradabile, toxic and carcinogenic [1-3]. Currently, coking wastewater is usually treated by different forms of A/O biological nitrogen removal processes as the primary treatment means, but the aforementioned processes are not efficient enough to meet the requirements of the National Discharge Standard in China (GB13456-1992). According to the continuous requirement on improving environmental protection for the coking industry (revised 2008), increasing wastewater utilization ratios and reducing the discharge of effluent in the coke industry have to be implemented for cleaner production and sustainable development. Therefore, advanced technologies need to be developed to treat coking wastewater and reutilize the product as industrial cooling water, which would be one of the best choices to achieve zero discharge of wastewater and reduce water consumption per ton of steel produced. In this study, a three-dimensional fluidized bed electrode reactor was adopted for the advanced treatment of coking wastewater, and the effects of operating conditions, including particle dosage, initial pH, current density, supporting electrolyte, as well as aeration amount on the COD removal rate, were investigated. Its running costs were also estimated."

Jan 1, 2012

By Suguru Kohno, Yoshihiro Momose, Masakazu Honma, Tokirou Kamosawa

Copper metal surfaces have been examined by an extremely sensitive surface analysis technique called temperature programmed photoelectron emission (TPPE). The surfaces were ultrasonically cleaned and subsequently abraded by a screw in organic solvents and water. The TPPE apparatus is composed of a Geiger counter with Q gas (He+ iso-C4H10). The curve of photoelectron emission (PE) intensity vs. wavelength from 300 to 170 nm, termed PE spectrum, was repeatedly measured at different temperatures in the temperature- increase process from 25 to 350°C. The number of emitted electrons in a PE spectrum (PE total count) increased, reached a maximum at-250°C, and decreased with increasing temperature. With the surfaces cleaned alone in the liquids the maximum PE total count decreased in the order C3H70H > (CH3) 2CHOH > C2HpH > CHPH > H2O. With the mechanically abraded surfaces in the liquids the maximum PE total count changed as a function of the abrasion period and the maximum tended to appear at higher temperature with increasing abrasion period; the maximum value at 10-min abrasion decreased in the order H2O > CHpH > C2HPH > (CH3) 2CHOH > n-C3HpH. It was suggested that the TPPE behavior can be related to the acid-base interaction between the alcohols and the abraded metal surfaces and the presence of a contaminant over layer on the surface. From the XPS analysis of the 01 s spectra it was suggested that the chemical change of the adsorbed oxygen to oxide oxygen with temperature plays a substantial role in the appearance of the maximum PE total count.

Jan 1, 2000

By R. Schuhmann

The thermodynamic data and calculations which underlie the design of the Q-S process for coppermaking are summarized. The efficient production of crude copper and slag of low copper content in a single con¬tinuous converter requires the establishment and control of gradients in oxygen activity and other physico-chemical variables throughout the reactor. These gradients are established by stagewise introduction of oxygen and solid feed materials to provide: (a) flash oxidation of sulfides above the bath, utilizing the great bulk of the oxygen, (b) conversion of high grade matte or white metal to crude copper by bottom blowing with restricted bath turbulence, (c) close approach to equilibrium staging of converting and deconverting reactions along the length of the slag layer, from a maximum oxygen activity near the metal discharge end to a minimum at the slag discharge end, and (d) completion of slag cleansing by deconverting. In terms of the Phase Rule, the Q-S process involves a system with a minimum of 5 components (Cu, Fe, S, O, and SiO2) and several liquid, solid, and gaseous phases. Accordingly, basic data from previously reported studies on simpler systems are utilized to prepare an equilibrium diagram for the 5-component system and to generate a quantitative thermodynamic model for the Q-S process. This model shows in particular the ranges of oxygen activities (measured by equivalent CO2/CO ratios) involved in the Q-S process and the relations of oxygen activity to temperature and other important physico-chemical variables of coppermaking.

Jan 1, 1976

By Marta Cabral, C. A. Nogueira, F. Margarido

"Physical processing of spent batteries which includes shredding and sieving operation is the first step for chemical treatment by hydrometallurgy. A laboratory study was carried out to evaluate physical processing efficiency, by analysing the resulting particle size, of alkaline and saline mignon-type Zn-MnO2 batteries. After shredding with a tip shredder, results obtained showed that alkaline batteries were more efficiently size reduced than saline batteries. Difference in particle size distribution was larger for granulometric fraction -20+11.2 mm and also higher for saline batteries. Average diameters (d50) for saline and alkaline batteries were respectively 9.1 and 6.2 mm. Chemical composition carried out on several granulometric fractions allowed to identify metals distribution through size categories. This analysis showed that zinc concentration with the grain size was almost constant, while manganese decreased when particle size increased. More than 95% of iron scarp from the battery cases had a particle size higher than 5.6 mm.IntroductionRecycling process of spent batteries includes physical unit operations which involves a fragmentation step in order to open the battery cases and to allow the access of chemical reactants to the electrode materials, on further chemical unit operations. Shredders are usually used for that purpose, using cutting mechanisms and allowing efficient fracture of residues in order to promote further processing of the contained materials. Batteries are complex products with a large variety of sizes and shapes which causes serious difficulties for predicting and carrying out its fragmentation.Domestic-type batteries are essentially of the Zn-Mn systems and with cylindrical shape, varying from the large size Mono (or D) type to the small size Micro (or AAA) type [1]. Recycling of batteries involves collection, sorting [2] and metallurgical processing [3, 4]. In some processes, the first step of metallurgical processing is dismantling and size reduction by shredding. Research work on spent batteries considering grinding/shredding and physical separation of fractions is scarce [5-7], but investigation in this domain is very necessary."

Jan 1, 2008

By Mitsuru Tanahashi

In order to develop an effective process for the production of from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at a solar-grade silicon (SOG-Si) 1773K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten M6-8 followed by oxygen gas injection into the melt (Two-stage connecting process). II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection Process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By Mitsuru Tanahashi

In order to develop an effective process for the production of a solar-grade silicon (SOG-Si) from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at 1773 K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten MG-Si followed by oxygen gas injection into the melt (Two-stage connecting process). II) II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By J. L. Jambor, H. W. Nesbitt

Oxidative dissolution of pyrrhotite and pyrite is largely responsible for the sulfate-rich waters of the vadose zone in the Waite Amulet tailings. Although the shallowest of the sulfate-rich waters are of the Fe-SO4 type, they change to Mg-SO4-type, near-neutral waters within 1-2 m of the tailings surface. Phyllosilicates and amphiboles are the only minerals present in sufficient quantity to ameliorate the amount of acidity produced. X-ray diffraction and microscopic studies of bulk sample indicate that quartz, chlorite, talc, amphiboles, magnetite, albite, and micas are the major and minor non-sulfide minerals, but their variations with depth do not give clear indications of depletion in the vadose zone. Mineralogical and bulk chemical compositions of the tailings confirm that Fe2O 3 has accumulated in large quantity in the vadose zone, with the Fe having been derived from Fe sulfides. When the effect of Fe2O3 is accounted for, the bulk compositions suggest that SiO2 is slightly more abundant in the vadose zone than in the saturated zone. This may be the result of residual enrichment of siliceous minerals such as quartz and albite in the vadose zone. Weathering of the tailings since the cessation of deposition in 1962 has resulted in a well-defined zone of sulfide depletion and secondary sulfate-mineral development. Although some silicate dissolution is indicated by pore-water compositions, the role of silicates in providing neutralization seems to have been minimal. The contribution by silicate minerals in laboratory tests of neutralization potential may be excessive relative to that in natural settings.

Jan 1, 1999