Search Documents

By Florian Kongoli

The production of a homogeneous self-fluxing sinter is an important step in iron making processes. A good sinler should have good permeability and reducibility and has to keep those characteristics for a certain time. An early melt down of the sinter in the blast furnace, where its solid state reduction is essential, would cause many problems such as low permeability and reductibility. Nevertheless, the important factors that influence these characteristics, such as the chemistry of the sinter and the fluxing effect during sintering and sinter reduction conditions have not yet been clarified, In today's new reality where many new minor components such as Al2O3 and MgO enter to the sinter through raw materials, the quantification of the fluxing effects during sintering becomes even more important. In this work, the liquidus surface and phase relations of the sinter primary melts in the CaO-FeO-Fe203-Si02 system at sintering conditions have been quantified. The fluxing effect of oxygen potential, Al2O3 and MgO has also been quantified by the means of some practical diagrams that can directly help the optimization of the sintering processes.

Jan 1, 2003

By Masami Taguchi

"It is found that lead monoxide, PbO, has an ionic conductivity, and the all solid-state electrochemical cell using this oxide as an electrolyte has attracted the attention of battery researchers. In this study, thin film PbO2/PbO/Pb solid cells were produced on glass substrates and their discharge properties were investigated. The acti.ve material for the positive electrode, PbO2, was obtained by reactive sputtering of a Pb target in oxygen plasma. The PbO electrolyte and the active material for the negative electrode, Pb, were vacuum evaporated from /3 -PbO powder and a Pb block, respectively. The open-circuit voltage of the cell agreed with the theoretical value based on the thermodynamic data, and the close-circuit voltage was improved by the addition of a univalent impurity such as sodium or potassium to the PbO electrolyte. The connection of the cells in series and in parallel produced a higher electromotive force and a larger capacity. Also, the charge-discharge cycling test revealed that the cell could be charged and function as a storage battery.IntroductionGenerally, the ionic conductivity of a solid-state electrolyte is lower than that of a liquid electrolyte near room temperature. This has been a serious obstacle to using such electrolytes in an electrochemical cell. However, some solid-state electrolytes, which can preferentially pass a specified ion and have high ionic conductivity, have been found. Lead monoxide, PbO, which is an oxygen ion conductor, is such an example (1)(2). If a solid-state electrolyte is adopted for use in an electrochemical cell the problem associated with a liquid electrolyte such as leakage can be alleviated. The cell structure also can be simplified, because the electrolyte plays the role of separator to prevent the active materials from mixing. Thus, physical vapor deposition technology may make it possible to develop a very thin film cell, which consists of only solid phases (3)(4). In this study, the thin film PbO2/PbO/Pb solid cell with a thickness· of only a few micrometers, in which all the constituents were systematically deposited on a glass substrate by reactive sputtering and vacuum evaporation, has been produced and the charge-discharge properties were investigated. An attempt was made to improve the discharge properties by doping impurities such as Na2CO3 and Sb2O3 into the PbO electrolyte. Moreover, the connection of the cells in series and in parallel to get a higher electromotive force and a larger capacity, and the charge-discharge cycling test to determine its use as a storage battery were carried out."

Jan 1, 2000

By Qingyu Deng, Shiwei Ma, Guibao Qiu, Hua Wang

"The flow behavior of the blast furnace slag bearing titanium, like viscosity, play an importance role during the iron-making process with the vanadium-titanium magnetite, which is a very special minerals in Panzhihua, China. The dependency of the viscosity on the chemical composition like TiO2, Al2O3, MgO, binary basicity (CaO/SiO2), temperature, reaction time were studied. The experiments showed that the viscosity decreased with the increase of TiO2, MgO content and binary basicity, and it increased with the increase of Al2O3 content and temperature. The viscosity showed a slight decrease within 60mins’ reaction with graphite crucible, however, it increased rapidly afterwards with the formation of Ti(C, N).IntroductionThe ordinary iron ore has been an essential part of raw materials for vanadium-titanium magnetite smelting in Panzhihua to avoid a series of problems, such as slag thickening, adhesive bond of slag and hot metal, etc. The ratio of vanadium-titanium magnetite has been decreased gradually since 1970s, and has down to about 65% now. However, with the substantial appreciation of price of imported ordinary iron ore, Panzhihua Iron and Steel Group aims to increase the ratio of vanadium-titanium magnetite and decrease the dependence on ordinary iron ore in order to lower the cost of smelting process."

Jan 1, 2012

By M. Mujahid, A. Maqsood, M. H. Asghar, K Iqbal

"Thin film multilayer anti-reflection coatings (Si02/Si/Si02) having thicknesses 286/571/143nm were deposited by RF magnetron sputtering deposition technique on 0.5mm thick Si(100)-substrates. Post-deposition annealing is also carried out in the temperature range 150-650°C for 4hr at the rate of 10°C /min. Si Optical window was designed at 4.21lm wavelengths and correlated with modeling software. The films are transparent in the 3-51lffi band of the electromagnetic spectrum, firmly adhered to the substrate. The prepared multilayer thin films are characterized optically and structurally using a spectrophotometer, an atomic force microscope, x-ray diffraction and a scanning electron microscope. Optical and structural characterizations show that the %transmittance is between 60% and 75%, no appreciable change in crystal structure and roughness of coatings vary between 9 and 25 nm when annealed in the temperature range of 150-650oC. Local elemental characterization on the surface of the thin film was carried out using energy dispersive spectroscopy. The quantitative result of energy dispersive spectroscopy has also shown that the ratio of Si to 0 on the film is 0.67: 1.IntroductionSi02 thin films have unique properties in the interfaces with Si and most studied materials in the field of microelectronics and optical devices [1]. Multilayer thin films are using nowadays in the design and fabrication of the shrinking systems with a variety of fields such as optoelectronic devices. The physical properties and parameters can be controlled at scales of microns down to nanometers by using RF magnetron sputtering system [2].Silicon and Silicon dioxide are used as coating materials [3]. These thin films are laid on top of each other in SiO2/Si/Si02 order by RF magnetron sputtering on top of a substrate as given in Table 1."

Jan 1, 2012

By Djalma Souza, Jean Igor Margem, Sergio N. Monteiro, Frederico M. Margem

Synthetic fibers have been used for many years to attend the demands required by the technologica lfields. However, the use of them has been questioned due to the impact on the environment. In this way, the natural fibers have received extensive attention, in particular hybrid fabrics of natural fibers to reinforce environmentally friendly polymer matrix composites. Thus, the present work has the objective of evaluating and comparing the mechanical properties of composites formed by hybrid fabric with 70% Malva—30% Jute in epoxy polymer matrix. The tests carried out are the Charpy and Izod Impact Tests, with specimens of 10, 20 and 30% in volume of hybrid fabric environmentally friendly into polymer matrix composites at room temperature. The 30% samples had the best results, functioning as an efficient reinforcement.

Mar 1, 2018

By Olga Frank-Kamenetskaya

The experimental results of study of atmospheric corrosion processes on Saint-Petersburg bronze monuments surface, received in situ and by means of simulating experiments, have been discussed. Influence of the time factor on corrosion film (patina) mineral composition has been analyzed. Direct dependence between patina mineral composition and environmental conditions has been proved. The sequence of patina phases crystallization has been established. Effect of the chemical composition and heterogeneity of artistic bronze and also monument surface structure on the rate of corrosion process has been regarded. The time variations of mass of the crystallized in the hydrochloric acid vapor phases have been investigated. The kinetic laws of their development at the initial stage of formation, indicating simple (non chain) reactions, have been revealed.

Jan 1, 2006

By Lucas Lopes da Costa

In this work, a natural foam extracted from the Amazon buriti palm tree is investigated as possible substitute for synthetic foams. The basic physical and mechanical properties of this biofoam were evaluated. Its sponge-like structure was characterized by the amount of pores and morphological aspects. It was found that the buriti biofoam displays a very low density of the order of 0.1 g/cm3 with a relatively good compressive strength. This would be suitable for several engineering applications and as a new material with the potential for replacing currently applied synthetic polymeric foams.

Jan 1, 2010

By F. A. Guo

Ultrafine-grained surface layers were obtained by surface mechanical attrition treatment (SMAT) in copper and titanium samples. The thermal properties of the deformed layers were characterized using a scanning thermal microscopy (SThM) that allows thermal conductivity to be mapped down to the submicrometer scale. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a powerful tool for the thermal property and microstructural analysis of ultrafine-grained microstructures.

Jan 1, 2006

By J. Phillip Mackey

A whole new group of non-ferrous pyrometallurgical processes with the ability to utilize tonnage oxygen and capture sulphur dioxide were developed and commercialized over the period 1940s–1980s. Many of these earlier process developments were undertaken with limited knowledge of the process chemistry and influence of key process variables; in many cases, piloting helped provide much new physico-chemical data, but gaps remained. The second generation versions of these technologies of today provide all the primary copper, nickel and lead produced worldwide by pyro-metallurgical smelting. Further, process development has continued and a new generation of copper and lead smelting technologies have also been developed in China since the 1990s. The older reverberatory and blast furnaces have been progressively replaced by the newer technologies—a good example being the introduction in 1992 of the copper IsaSmelt technology at the Mt. Isa smelter in Australia where the former fluid bed roaster and reverberatory furnaces were replaced by a single new smelting unit, together with an acid plant for sulphur dioxide collection. The development of these new technologies was made possible by investment in fundamental and applied research. The lesson for the future is, in order to sustain these improvements, continued investment in research and development capability is required—to do otherwise is to risk obsolescence and lack of competiveness in the world market. Dr. Peter Hayes at The University of Queensland is one of the many researchers and process engineers who have contributed to the fundamental understanding of metallurgical processes over this period of rapid change in technologies. The present paper briefly outlines some of the many contributions Peter Hayes has made to the understanding of kinetics, mechanisms and phase equilibria in metallurgical systems, and metallurgical process development.

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van't Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985

By François Larouche

Since their commercialization in the early 1990s, lithium-ion batteries (LIBs) have become ubiquitous for powering a myriad of portable electronics. Their usage now extends to the automotive industry and stationary energy storage market. With an average life of 6.2 years and the strong demand, the volume of spent LIBs has increased exponentially, making recycling mandatory. Currently, recycling/ recovery of spent LIBs is limited in comparison to all other types of batteries. The current processes focus mainly on the recovery of the most valuable metals such as cobalt and nickel, leaving lithium and phosphate in a low value end-product. It is necessary that new advanced recycling technologies are developed for the recovery of spent LIBs both from an economic and environmental perspective. In this paper, the current R&D status of LIBs recycling is reviewed with the emphasis placed on hydrometallurgical processing opportunities for Li-ion and Li-solid state batteries.

By P. N. Anyalebechi

The effects of solidification rate on the cast microstructures of aluminum alloys 6009 and 6016 have been investigated with directionally cooled laboratory-size ingots, at 0.2-10.1 K/s and 0.4- 23.1 K/s, respectively. These ranges of solidification rate are within those observed in commercial-size ingots. In both alloys, the average dendrite cell size and second phase particle size decreased with increase in average solidification rate and with a decrease in average local solidification time. However, at comparable solidification rates, the dendrite cells and second phase particles are finer in the shorter freezing range alloy 6009 than in the longer freezing range alloy 6016. This is provisionally attributed to the earlier formation of second phase intermetallics at higher temperatures during solidification and to the formation of greater amount of the relatively coarse plate-like ß -phase (Al9Fe2Si4) phases in alloy 6016. In general, in both alloys, the types and relative amounts of the second phase particles in both alloys are independent of solidification rate.

Jan 1, 2006

By Chuan-fu Zhang

In present work, the physical properties of molten FenO-MgO-CaO-SiO2 slags were measured .It is shown by the results that when the slag composition is as follow: MgO 8%~12%, CaO 2%~8%, Fe/SiO2 1.2~1.6, the viscosity of the slags decreases with the increase of temperature. When the Fe/SiO2ratio and the MgO content are fixed, the electrical conductivity increases and the viscosity decreases as CaO content increasing, while the content of CaO exceeds 6% its influence weakens. When the MgO content is 11% and the CaO is 6%, the viscosity of the slag decreases markedly as the increase of Fe/SiO2 ratio. Its influence to viscosity is inconspicuous when the Fe/SiO2 ratio exceeds 1.5. When the CaO content is 6% and Fe/SiO2 is 1.2, the electrical conductivity decreases with the increase of MgO content as temperature is below 1290, but increases when temperature is above 1290. When the MgO content is 11% and the Fe/SiO2 ratio is 1.2, the electrical conductivity increases with the increase of CaO content. When the CaO content is 6% and MgO content is 11%, the electrical conductivity increases as the increase of Fe/SiO2 ratio, while its influence weakens as the temperature increases continuously. The electrical conductivity rises when temperature increases at any slag content. The melting temperatures of FenO-MgO-CaO-SiO2 semi- synthesis slags from this work were below 1290.

Jan 1, 2006

By Y. Z. Zhang

Electrochemical oxidation of arsenopyrite in ferric sulphate media in the absence and presence of bacteria T jerrooxidans has been investigated for the purpose of understanding the dissolution chemistry of arsenopyrite and the bacteria attack mechanism. Mixed potential, polarization resistance measurements, polarization curve, cyclic voltammetry experiments were conducted in a ferric sulphate medium of 10g/L FeH, temp.25-35°C, pH 1.5-2.5 in the absence and presence of bacteria Tjerrooxidans, respectively. For the anodic process, a two-step reaction sequence is suggested by the electrochemical measurements. The initial step at a low potential is described by:

Jan 1, 1996

By Hiroyuki. Fukuyama

The pseudo-binary phase diagram of the cuspidine (3CaO2?SiO2?CaF2) - CaF2 system has been studied by electron probe microanalysis (EPMA) and X-ray diffractometry (XRD). To prevent fluorine loss in the form of a HF gas by a reaction of CaF2 with water vapor at elevated temperatures, the equilibrium experiments were conducted with the sample hermetically sealed in a platinum tube. By employing this technique, it was successfully revealed that cuspidine exists as a stable phase and congruently melts at 1684 ± 1 K, and the cuspidine - CaF2 system presents a simple eutectic type of phase diagram, of which eutectic temperature has been estimated to be around 1540 K, corresponding to the composition of 40 mass% 3CaO?2SiO2 - 60 mass% CaF2?

Jan 1, 1999

By Oscar J. Restrepo

Through reactions in solid form at high temperatures, using iron oxide (Fe3O4) and chromium oxide (Cr2O3) in fixed proportions as precursors, the compound was synthesized with spinel structure type FeCr2O4. For different temperatures synthesis was conducted the characterization of the material obtained through X-ray diffraction (XRD), spectroscopy UV-VIS-NIR, scanning electron microscopy (SEM), energy dispersion analysis of X-ray (EDX) thermal analysis (DTA / TGA) and magnetic susceptibility of alternating current. The changes in the spectra of reflectance changes are related to the phase identified, the degree of crystalline structure, the spatial order of cations and the magnetic behavior obtained.

Jan 1, 2009

By Taegong Ryu

A thermal plasma process was used to synthesize nanosized tungsten carbide -cobalt composite powder, in which ammonium paratungstate and cobalt oxide were reacted with a gas mixture containing CH4, H2 and Ar. The reduction and carburization of vaporized precursors produced nanosized tungsten carbide (WC1-x) - cobalt composite powder, which sometimes contained small amounts of W2C and/or W phase. The effects of gas composition, plasma torch power, and the flow rate of plasma gas on the product composition and grain size were investigated. The grain size of synthesized tungsten carbide powder was less than 20 nm. The synthesized composite powders were also subjected to a hydrogen heat treatment to fully carburize WC1-x, W2C, and W phases to the WC phase as well as to remove excess carbon in the product. Finally nanosized WC-Co composite powder of grain size less than 50 nm was obtained.

Jan 1, 2009

By John W. Lund

The Geo-Heat Center has been investigating the utilization of waste silica from the Cerro Prieto geothermal field for several years. The main objectives of the research were to com-bine silica with various additives to (1) form bricks for low cost housing, and (2) to produce a suitable road surfacing material. The various additives that were tested included hydrated lime, portland cement, plastic fibers, asphalt cement and emulsified asphalt. The silica-cement combination produced the strongest bricks and had the best weather resistance, whereas, the silica-lime combination produced the bricks with the lowest thermal conductivity and specific gravity density. The addition of plastic fibers to the silica-lime mixture improved both strength and weather resistance. The combination of asphalt and silica is not suitable as a road surfacing material, however, silica-cement appears promising.

Jan 1, 2006

By Wang Zhi

High-Mg-content concentrates are usually treated in Jinchuan flash smelting Furnace. Because the viscosities of high-Mg-content slag is very high, the operation of flash smelting becomes very difficult. To solve this problem, the viscosities of the semi-synthesized FeO-MgO-Si02 slag of different compositions were measured. The results showed that when in the slag the weight percentage of MgO [m(Mgo)] is 6-10%, the ratio of the weight percentage of iron to that of Si02, m(Fe)/m(SiO2) is 1.1-1.4 and the temperatures are within 1473?1773K, the slag viscosities increased with the increase of m(Mgo) and m(Fe)/m(sio,). When m(Mgo)<6%, the smelting temperature should be controlled at I 300°C in order to to keep the smooth operation. When m(Mgo» 10%, the temperature should be kept above 1633K. When the content of MgO is higher, a lower viscosity slag ean be produced by decreasing the ratio of m(Fe)/m(sio,). The appropriate ratio of m(Fe)/m(sio,) for Jinchuan flash smelting furnace is about 1.2.

Jan 1, 2003

By Antoine Allanore, Guillaume Lambotte, Bradley R. Nakanishi

Current industrial methods used for rare earth element (REE) extraction involve: 1) ore enrichment, 2) separation of rare earth oxides (REOs), 3) chlorination or hydrofluorination, and 4) individual electrowinning of REEs from a molten halide electrolyte. The complexity of REE extraction is inherited from their electronic configuration. Recently, molten oxide electrolysis (MOE) has been used to produce reactive metals directly from their oxides, e.g. titanium. As a single-step alternative to processes 3) and 4), or laboratory has investigated rare earth extraction by MOE. A key challenge is to find a molten electrolyte more stable than REOs. One possibility is to use binaries of REOs directly as a solvent. We have, therefore, developed two experimental approaches for studying molten REOs at temperatures exceeding 2200oC. The present work reports the most recent experimental results obtained with La2O3-Y2O3. Those promising results demonstrate potential for operating with molten REOs and refine the underlying materials challenge for electrodes to enable metal recovery.

Jan 1, 2015