Search Documents

By Linli Wu, Guangchun Yao

"The influence of deformation on the properties of short-carbon-fiber reinforced 2024 alloy matrix composites was investigated in this study. It was found that the distribution of carbon fibers changed from the random state before deformation to the ordered state that carbon fibers arranged along the direction of rolling and extruding after deformation. Under the temperature range in control, the increase of rolling and extruding temperature would benefit to improve strength and elongation of composites, but was not conductive to improve the hardness of composites. With the increment of total deformation, all the strength and the hardness of composites became greater, nevertheless the elongation decreased. After being rolled and extruded, the strength and the hardness of composites were all bigger than those of composites before being rolled and extruded; moreover, the strength of extruded 2024 alloy matrix composites was higher than that of rolled 2024 alloy matrix composites under the same heat treatment conditions.IntroductionCarbon fibers have been reckoned as very important reinforcements due to the high specific strength, specific modulus, high thermal and electric conductivity, low expansion coefficient and good self-lubricant properties [1-4]. Light metal composites reinforced with carbon fibers, such as carbon fibers in an aluminum matrix, are widely used and studied. Some studies have concentrated on the interfacial characteristic of CF/Al composites in order to search for the way of improving the bonding between carbon fibers and the matrix alloy [5-8], and on the influence of the carbon fiber percent composition in the composites [9-11]. Some researchers began to take interest in the deforming characteristic and failure behavior of carbon fiber reinforced metal matrix composites [12-16]. However, the same with other metal materials, most of CF/AI composites were prepared by some single processes, such as powder metallurgy, extrusion casting and vacuum press infiltration, which caused that the composites products could not be manufactured directly. In order to cover the shortage of the mentioned above processes and get composites products with perfect mechanical properties and dimensional accuracy, the composites should be reworked by rolling, extruding or forging process. Compared with research about manufacturing process, the correlative investigation on the reworking of CF/Al composites was much less evidently, which restricted the application and the further development of CF/Al composites."

Jan 1, 2012

By Maria Kuttig, Christian Ruback, Gerhard Tober, Petra Maier

"It has been demonstrated that there is a strong relationship between work hardening with various post heat treatment and cyclic deformation behavior of structural steel S275. This study contributes to a project developing a process for the complex forming of steel, which combines rolling and bending. Due to the complex geometry of the final work piece, the deformation degree varies greatly. The forming temperature, as well as post heat treatruent, influences recrystallization processes in dependence of the local deformation degree, resulting in inhomogeneous microstructure of the work piece, which affects the quasi-static and dynamic properties. Cyclic creep and hardening or softening has been monitored during constant amplitude loading at stresses near fatigue strength in normalized condition. Work hardening, stress relief or recrystallization influence the cyclic deformation behavior and produces cyclic creep effects. Cyclic softening or hardening and creep were observed to occur in parallel. To what extent these properties are noted depends on the deformation degree.IntroductionThis work is part of a research project developing a new process for the three dimensional forming of steel. For the final product the fatigue strength influenced by the forming parameters is very important. Due to its complex geometry, the formed final plate has different deformation degrees. This leads to different recrystallization behavior and heat treatruent will have different effects on the microstructure. The peak deformation degree cp of the plate will be around -0.5 what leads to the analysis using rolling from 22 mm to 13 mm of thickness. The quasi-static material properties are very important for calculating the preliminary design. However, work pieces which are cyclic loaded need fatigue tests to describe the in-service material behavior. [l] For the prediction and to guarantee the wanted life-time of the part cyclic deformation tests are important. [2, p.23-32] When it is assumed that the work piece will only loaded in cyclic tension, fatigue testing will be done from zero to a maximum force value. In preliminary tests this value is the tensile fatigue strength from a Smith diagram. During processing, here forming, work hardening takes place resulting in strengthening. Therefore, in further tests maximum load can be increased to monitor cyclic deformation mechanism in more detail. However, to study cyclic creep and hardening and softening data should be evaluate over sufficient life time and should not fracture too soon."

Jan 1, 2013

By Chen Yongming

In order to eliminate the serious environmental pollution caused by low concentration of sulfur dioxide smoke in antimony smelters, a new smelting process, named as reducing-matting smelting, is proposed in this paper. The effects of technical conditions such as smelting temperature, smelting time, Pyrite cinder addition and the amount of additive on the smelting of stibnite concentrate have been investigated by the method of single-factor experiment. The results show that the optimum conditions are as follow: The amount of pyrite cinder is 1.2 times of its theoretical amount. The addition of soda and sodium sulfate is 15% and 72.6%, respectively, to the amount of stibnite concentrate when the total amount of sodium is 30%. The reducing-matting smelting is conducted at 1100°C for 2h then the smelting temperature is raised to 1200°C for 50min. Under the optimum conditions, the direct and total recovery ratio of antimony can gain 90.99% and 98.87%, respectively, and the fixed ratio of sulfur is higher than 99%.

Jan 1, 2006

By M. Arenas

A corrosion study of a bonded NdFeB permanent magnet materials alloyed with titanium carbide additions has been undertaken. The materials were produced by rapid solidification by melt spinning. Commercial epoxy was used as a bonding medium. The corrosion results were compared with those of a near stoichometric unalloyed NdFeB. Anodic polarization and potentiostatic techniques in 0.9 M Na2SO4 solutions were used to characterize corrosion behavior. It was found that the addition of 6 a10 Tic resulted in superior corrosion resistance, as indicated by lower corrosion currents and less iron dissolution at fixed potential.

Jan 1, 1997

By F. E. Katrak

Rare earths markets by definition usually include not only the rare earth elements, but also yttrium. They can be subdivided into a very large light rare earth fraction (about 95 percent by weight of all rare earths consumed) consisting mainly of cerium and lanthanum and a smaller fraction (with much higher unit value) consisting of selected high-purity oxides or elements such as yttrium, europium, samarium, or neodymium. CRA estimates that the noncomnunist world market for all rare earths and yttrim was on the order of US$750 million in 1986. The main focus of this paper is on the principal uses for rare earths, some CRA-developed proprietary data on their consumption by region, and the selective nature of business opportunities in the rare earth markets. We also provide forecasts on the future trends in these markets.

Jan 1, 1989

By Kent D. Peaslee, Lifeng Zhang, Edith Martinez, Yufeng Wang

The current study investigated the multiphase fluid flow, heat transfer, solidification of the steel, and the motion and entrapment of inclusions during the centrifugal casting process using FLUENT software. User-defined functions (UDFs) were developed to add velocity with a value related to the rotation speed and radial distance to the solidified steel, to exert a centrifugal force to the motion of inclusions, and to add the entrapment condition of inclusions at the solidifying shell and export the entrapment locations of the inclusion. The calculation shows that there are two peaks of inclusions along the thickness of the produced tube: one at close to outer surface and another one close to the inner surface of the tube. With a larger rotation speed, inclusions tend to be entrapped more towards the inner surface. The calculation agrees well with the industrial measurements.

Jan 1, 2012

By Ravinder N. Reddy

Electrochemical capacitors are charge storage devices. They bridge the gap between dielectric capacitors and batteries in terms of energy and power density. Electrochemical capacitors are classified into two types, electrochemical double layer capacitors (EDLCs) and capacitors based on pseudocapacitance. In EDLC, charge is stored at the interface between electrode and electrolyte. Carbon is considered to be prime electrode material for EDLCs due to its many favorable characteristics. In this study carbon materials are derived from thermal decomposition of catechol- formaldehyde polymers and are studied as electrode material for electrochemical double layer capacitors. Carbon electrode surface is characterized using NOVA 1200 gas sorption analyzer. It is also characterized using XRD and SEM. Carbon electrodewaselectrochemically characterized using cyclic voltammetry (CV). A highest capacitance of 110 F/g was observed in 30 wt% H2SO4.

Jan 1, 2006

By Hans von Michaelis

There has been a renaissance in gold and silver extraction and recovery that has taken place over the last fifteen years, since the price of gold was freed from the $3510~ level. Despite major advances in such areas as carbon adsorption processes for gold recovery, refractory gold ore treatment, crushing and grinding, process control, etc., there still remain several gold and silver mineral processing frontiers. Frontiers related to environmental management present significant challenges especially in the USA. More than ever it is appropriate to optimize total economics by adopting a "systems approach" that integrates mining, mineral processing and environmental management.

Jan 1, 1993

By Saeid Pournaderi, Ahmet Geveci, Ender Keskinkilic, Yavuz A. Topkaya

"This study investigated calcination behavior of one of the Turkish laterite deposits, which was recently found in Sivrihisar region. Representative limonitic laterite samples (1.26% Ni) taken from Yunusemre Karasivritepe and Kucuksivritepe location were first subjected to drying. Removal of chemically bound water and other volatiles were then studied, in detail. In the calcination experiments, temperature and time were the main experimental variables. Thermal treatment was conducted at the specific temperatures in 250 °C - 800 °C range. The weight losses due to elimination of chemically bound water and other volatiles were reported to be approximately 10 per cent of the weight of the ore. For the particle size used in the current work, 700 °C and 40 minutes were determined to be the optimum calcination temperature and time, respectively.IntroductionThe nickel ores that are economically valuable can be grouped into two categories: sulphide type nickel ores and oxide type nickel ores, namely laterites. Over all reserves in the world, 40% are sulphide nickel ores and the remaining 60% are laterites [1]. Pyrometallurgical nickel extraction from sulphide type nickel ores is conducted via matte smelting. More recently, laterite ore bodies have been subjected to nickel extraction. Depending mainly on the chemical composition of the laterite and the process economics, various extraction techniques have been implemented: pyrometallurgical route involves ferronickel smelting. High pressure acid leaching (HPAL) is the commercial method for hydrometallurgical nickel extraction, while ammonia leaching (CARON Process) is a combination of pyrometallurgical and hydrometallurgical processes [2]. With the improvements in these processes, it is predicted that laterite’s share in the world nickel production will rise to 50% in 2012, while it was reported to be 42% in 1,200,000 tons of annual production in 2003 [3]."

Jan 1, 2011

By Bruce R. Conard

Consideration of environmental and human health issues in metallurgy is growing rapidly. While not all metallurgists need to have detailed expertise in environmental and health questions, they should be aware of the challenges the metals industry faces, be able to interact with colleagues in other sciences and contribute to sound metal resource management. Hydrometallurgists occupy a unique position among metallurgists because of their knowledge of the behaviour of metals in aqueous systems, which are of fundamental importance in understanding environmental chemistry and human toxicology. As a result, hydrometallurgists should more frequently and passionately lend their expertise in assessing environmental and health risks of metals and in helping to develop effective global guidelines, regulations and process and product stewardship strategies, thereby enabling metals to continue their beneficial service to society.

Jan 1, 2003

By Paul Pajunen, Michael Sheedy

"Acid separation using short bed ion exchange is a now well established technology in copper refinery tankhouses. Refinery bleed streams from liberator cells are treated by short bed systems to produce an acid-free byproduct stream that contains the bleed metals and valuable nickel salts. Removing the acid eliminates the need for a black acid evaporator and reduces the amount of sodium carbonate required in nickel selective precipitation processes. The recovered sulfuric acid can be recycled to the tankhouse. This same technology is routinely used to treat other acids such as hydrochloric, nitric, and hydrofluoric. In the case of hydrochloric acid, the process can selectively separate chloro-anionic complexes such as Zn, Pb, and Cu, which are then eluted with water. The acid recovery technology can also be closely coupled with ion exchange processes in order to minimize regenerant acid consumption. In many hydrometallurgical applications resin regeneration often requires an acid dosage multiple times the stoichiometric minimum. Coupling an acid recovery bed with the IX column allows recovery and recycle of the free acid in the spent regenerant, thus reducing the overall acid consumption to just slightly more than stoichiometric.Short Bed Ion ExchangeThe short bed ion exchange process has been extensively used in the metal finishing industries since the early 1970s [1,2]. Short bed systems have also been sold to primary metals producers for the separation of sulfuric acid from copper refinery bleed streams [3] and for the recovery of nickel and cobalt from plant effluent streams. This unique technology optimizes the ion exchange process and offers a number of significant advantages over conventional ion exchange. The principal features and benefits of this technology are presented below."

Jan 1, 2012

By H. Soto, J. Jara, F. Nava

A method has been developed to recover cyanide and copper from solutions containing copper complexes and thiocyanate. Copper is precipitated as copper thiocyanate or as copper cyanide depending on pH and the concentrations of thiocyanate and cyanide in the effluent. The copper precipitate assays over 50% copper and presents good dewatering characteristics. After settling it can be separated from the effluent by filtration. The solution containing the bulk of the cyanide is then oxidized with ozone to transform the remaining thiocyanate into cyanide. This results in a regenerated solution rich in free cyanide that can be recycled to the cyanidation process. Careful control of the pH of the solution is required. First, pH of the effluent is lowered to optimize the precipitation and oxidation stages, then the pH is restored to an alkaline value to regenerate the cyanide solution. Recoveries of over 96% copper and cyanide were obtained in laboratory tests using industrial solutions. With this procedure, cyanocidic gold/copper ores could be treated economically by heap leaching, since the cyanide consumed by the copper impurities could be regenerated at very low cost (most of the cost of cyanide regeneration would be compensated by the copper credits). In order to achieve this, a bleed of the barren solution could be treated by the proposed method, and then recycled to the leaching step. The volume of solution to be treated should be large enough to keep a cyanide/copper molar ratio higher than 3:1. This would assure that copper does not cause undue interferences in the leaching or the carbon adsorption stages. If the thiocyanate content is low, the oxidation stage can be avoided, and the solution can be recycled to the leaching stage directly after the solid-liquid separation stage.

Jan 1, 1997

By James C. Sever

"With the advent of high energy costs and increasing concern for the environment leading to the incorporation the C02 life cycle as a criteria for the material used in a finished product, it is beneficial to analyze the plant and the process used in producing a raw material in order to identify practical, economic energy recovery opportunities. To this end a study was made of the proposed Nevada Clean Magnesium, Inc. Tami-Mosi reduction facility. Each source of waste heat is listed together with the assessment for potential co generation or direct recovery. The overall impact on energy requirement and C02 generation is provided.IntroductionHistorically metal reduction plants, large consumers of energy, do not recover waste heat. This occurred for many reasons:• Energy costs were low and the capital for a co-generation system could not be justified;• Waste heat sources contained entrained solids or liquids which would inhibit efficient energy recovery;• The exit temperature for the heat source was too low for efficient use by aaqueous Rankine cycle system.The business environment has now changed adding impetus to the recovery of energy previously discarded. Power costs have greatly increased. Global warming and the impact of carbon dioxide on the environment has become an issue which could impact the permitting of a plant. Technology improvements especially the development of a scaling environment waste heat boiler [l] and the development of the organic cycle Rankine cycle recovery system enable up to 70% energy recovery from ""low grade"" heat sources [2].With the inception of Nevada Clean Magnesium, Inc. 's (formerly Molycor Gold Corporation, Inc.)Northern Nevada Tami-Mosi project [3], an opportunity was presented to incorporate energy optimization from the initial design phase."

Jan 1, 2013

By Kazuyoshi Sato, Keizo Uematsu, Nozomu Uchida

"Confocal fluorescence scanning laser microscope was applied to characterize the surface flaw of ceramics in great detail. A high potential -of the characterization technique is presented first. Then the technique was applied to clarify the relationship between the flexural strength of ceramics and the surface flaw. This kind of direct information of surface flaw should be essential for the fundamental study in this area, but has been lacking. The examination revealed that large defects are present on the machined surface of ceramics. Their size is consistent to the flexural strength measured on the material. The characterization tool was also applied to examine the formation of surface flaw in machining of ceramics.IntroductionClarification of fracture origin should be the starting point in the study on strength in ceramics. However, this task has been extremely difficult in some ceramics, such as an alumina ceramics. It may break from both internal and surface flaws. The former should reflect the quality of production process and the latter the machining. Examination of surface flaws should be very important for developing a better machining method for ceramics. The knowledge may valuable for establishing a better production process also.ExperimentAlumina Referceram (JFCC) was used as samples. They are cut to size of 3x4x40mm, and the surfaces were ground to meet the requirements of testing method for flexural strength of fine ceramics, JIS R 1601. They were soaked in an aqueous solution of fluorescence dye and evacuated with an aspirator for an hour to allow the solution penetrate into surface flaws. After excessive solution remained on the surface was removed by gentle washing, the specimens were dried at 120°C for 48 hours. The 4 point bending mode was applied to measure the fracture strength."

Jan 1, 2000

By Honggang Zhong, Xin Cao, Qijie Zhai, Hongmei Song, Congsen Wu, Cheng Zhang, Jingzheng Ye

"The influence of superheat on the solidification structure and ferrite/austenite phase transformation of a novel lean duplex stainless steel (DSS) was investigated on a setup, which designed to thermally simulate the continuous casting process. The results showed that the macrostructure of the samples all exhibited chill zone, columnar zone and equiaxed zone. The distance from chill zone to position of columnar to equiaxed transition (CET) moved from 51.0 mm to 39.8 mm with an decrease of superheat from 70 °C to 10 °C, and that the grains in the chill zone tended to be finer. In equiaxed zone, the fme and uniform grains were observed when superheat higher than 40 °C; while, coarse grains were found in samples poured at low superheat. Generally, the volume fraction of ferrite increased along the dendritic growth direction, and stabilized in equiaxed zone. The high superheat decreased the volume fraction of ferrite in equiaxed zone, while it had indistinctive influence on chill zone and columnar zone.IntroductionDuplex stainless steel with approximately equal volume of ferrite and austenite, offering an attractive combination of corrosion resistance and mechanical properties. [ l]. The production of DSS, worldwide application in structural engineering[2] and petrochemical industry[3], have increase by more than 100% in the latest decade[4]. But due to the sharp prices increase of nickel and chromium, lean duplex stainless steels which have lower contents of alloy elements were developed. They perform well in both mechanical and corrosion resistance[S, 6] and even have TRlP(Transformation Induced Plasticity) effect[?]. Nonetheless , the mechanical properties of DSS was affected greatly by the solidification structure, such as columnar to equiaxed transition (CET), grain size and phase content[8]. So, the solidification behavior of stainless steel was investigated widely"

Jan 1, 2014

By Honggang Zhong, Wei Du, Qijie Zhai, Junjie Sun, Jingzheng Ye

"Effects of pouring temperature and cooling water flux on solidification structure of ferritic stainless steel are investigated with a thermal simulation setup. The results show that with pouring temperatures 1518° C, 1528° C, 1538° C and 1548° C, both Lmean (the mean length between columnar to equiaxed transition(CET) position and chill surface of the samples) and the mean dimension of equiaxed grains increase. On the other hand, with cooling water flux 400, 800, 1200 and 1600mL/min, Lmean gradually increases, and the mean dimension of equiaxed grains decreases. In addition, low pouring temperature and cooling water flux enlarge the ratio of fine equiaxed grains.IntroductionFerritic stainless steel plays an important role in industry products nowadays. Compared with austenitic stainless steel which contains both chromium and nickel, ferritic stainless steel can obtain good corrosion resistance despite the absence of nickel [ 1]. F erritic stainless steel has been widely applied in automotive exhaust systems [2], electrical equipment, construction and chemical industries and also has broad development prospects. At present, continuous casting technique has developed into an important technology applied in iron and steel making. The solidification structure of continuous casting slab has significant influence on the final properties of stainless steel. The developed columnar grains of ferritic stainless steel would result in negative effects on mechanical property [3]. However, fine and homogeneou& equiaxed grains can improve the comprehensive properties of ferritic stainless steel [4] Therefore, it makes great sense to promote the columnar to equiaxed grain transition (CET). Recently Baosteel has developed a new type of Cr-saved ferritic stainless steel, but the effect of continuous casting conditions on its solidification structure is unknown. It is important to investigate the effects of solidification conditions on solidification structure of this new ferritic stainless steel, which can give guidance for optimizing the production process."

Jan 1, 2014

By Matthew D. Andriese, Jiann-Yang Hwang, Zhiwei Peng

"It has been demonstrated that metallic-bearing minerals are physically liberated from host rock when exposed to microwave (MW) energy. The metallic minerals are iron sulfides and spinel oxide minerals contained in peridotite rock. Experimental evidence has shown ore particles readily couple with MW energy at 2.45 GHz, 1000 W resulting in rapid heating. Thermal stresses are generated by highly absorbing metallic-bearing minerals resulting in cracking and embrittlement of ore particles that assists in crushing and grinding processes. The liberated metallic-bearing minerals are shown to report to coarser size fractions as a result of MW exposure.IntroductionComminution of ore material during beneficiation is a large energy expenditure for the mineral processing industry. Crushing and grinding operations alone consume 50-70% amount of energy used in mineral processing [1]. Size reduction becomes increasingly difficult with decreasing particle size making grinding the most energy-intensive step of comminution. The aim of comminution is to maximize liberation of economically valuable minerals from the host rock [2]. Overall, the less material that needs to be handled, then grinded, to create a useful product for hydro/pyro metallurgical processes will achieve the greatest reduction of energy.Much of the scientific interest for use of microwave (MW) energy in mineral processing has been for improved hydro/pyro metallurgical techniques [3-6]. Early authors have employed MW energy for improved grinding of ore particles but most conclude the energy savings do not justify the energy input [7-9]. The effectiveness of MW assisted grinding is dependent on the ore mineralogy and the absorptive properties of minerals contained within it. Ore containing magnetic minerals should prove successful with MW assisted breakage from highly absorptive properties."

Jan 1, 2012

By Henry Salomon-De-Friedberg

Quebrada Blanca has had to overcome numerous challenges in achieving design throughput. The paper reviews how actual practice has evolved from the original design. The major challenges that were encountered from heap leaching to solvent extraction, the tankfarm and through to electro winning are discussed. The eventual solutions to some of the key issues are presented.

Jan 1, 1999

By Kaixi Jiang, Bangsheng Zhang, Lei Zhang, Haibei Wang, Xiaoping Zou

"China plays an important role in the global molybdenum industry; in fact, both China's molybdenum mine and smelter production ranked first in the world. The characteristics of China's molybdenum resources are quite complex, and moly-nickel ores with carbon, coppermoly ores and wulfenite can be only found in China. This paper firstly introduces China's molybdenum resource/ reserve situation. Secondly, the status of molybdenum smelting technologies, especially roasting by rotary kilns and multiple-hearth furnaces, are discussed. The practices and the development of some new technologies, such as pressure leaching, solvent extraction, ion exchange, carbon adsorption for moly-nickel ores and low grade molybdenite concentrates, are also introduced.IntroductionMolybdenum is widely used in special steels, aviation, alloys, chemistry, electronic and medical industries because of its excellent physical and chemical characters [1,2].In nature, molybdenum exists mainly as molybdenite associated with copper ore which are the main material for smelting. About 99% of molybdenum is produced from molybdenite. In addition, wulfenite, molybdenum oxide ore and graphite shale containing Mo-Ni have also industrial value to extract molybdenum and other metals such as Ni, Re, Pb and Zn. The reserves of molybdenum in China are about 8.4 million tons metal; China is ranked as the second largest source in the world. The output in China is more than 40 kt in 2010. Ferromolybdenum is the main product and then ammonium molybdate. The consumption in China is about 20 kt and the rest is exported to overseas.The first molybdenum smelter in China was built in 1963. Today the main producers include Jinduicheng Moly Company, Luanchuan Moly Company and Jiangxi Copper Group Company. Technologies and equipment have changed greatly. Roasting and multi-hearth furnaces are widely used. Several new processes were developed such as pressure leaching, solvent extraction, ion exchange and carbon absorption [3-8]."

Jan 1, 2012

By Eduard Ouerra, Nuo Jin

"The use of polytetrafluoroethylene, PTFE, as a solid sorbent for elemental sulfur during pressure oxidation of chalcopyrite was investigated. The effects of agitation, PTFE particle size and lingin sulfonate addition were evaluated using leaching conditions that were otherwise similar to those employed in the CESL process. The effects of these factors and their interactions on chalcopyrite oxidation are explained in terms of interfacial forces and solid-solid interactions. Using relatively fine PTFE powder with vigorous agitation resulted in about 100% copper extraction in less than 90 minutes without the need for grinding of the flotation concentrate.IntroductionThe extraction of copper from sulfide ores has always been dominated by the conventional pyrometallurgical smelting process. Though much effort has been made to develop various hydrometallurgical processing routes, smelting remains as the dominant process, treating approximately 80% of the chalcopyrite concentrates worldwide [1]. However, some of recently emerged techniques for treating chalcopyrite through hydrometallurgical routes are showing results that are competitive with smelting in terms of economical feasibility. Representative methods include: Activox Process, CESL Process, Anglo/UBC Process, High Temperature Pressure Oxidation, and Bio-Oxidation. Among these, the CESL processes operate at a medium temperature range (typically 140-150GC) and oxygen pressure of 100 psi, with chloride as a catalyst, and reportedly achieve copper extractions of about 95% with a light regrinding of flotation concentrate to a p95 of 45 ìðé [2]. In spite of this satisfactory extraction result, the leach residues contain significant amounts of conglomerates which contain a small amount of unreacted concentrate [2], The conglomerations are formed because the elemental sulfur generated is liquid and sticky (melting point of sulfur being 119°C), and has a tendency to wet the sulfide mineral surface, a fact which inhibits the oxidation of the minerals. The overall process chemistry of the CESL process may be summarized as follows [3]:"

Jan 1, 2012