Search Documents

By Saynbaatar, Gangping Ma, Jianhua Fu, Qiqige, Jinghua Wang

The influence on the performance of foam concrete made by replacing cement with some industrial waste residues was researched in this paper. The result shows that the 7d and 28d compressive strength of foam concrete increases firstly and then decreases with the increasing amount of industrial waste residue. The proper added range is 10%-20% for steel slag, blast furnace slag and coal ash, but, 8% for desulfurized fly ash. With the proper adding ratio, the compressive strength of foam concrete always increased comparing with the pure cement foam concrete. When adding 48% of the compound industrial waste residues, the 28d compressive strength of the foam concrete reached the 2.9MPa which could match the pure cement foam concrete. The results indicates that there is a synergistic effect among the compound industrial waste residue, and this effect is benefit to improving the compressive strength of foam concrete.

Jan 1, 2015

By G. Cifuentes

When the applied current is interrupted in a copper electrowinning plant, and then is back in operation, the lead anodes tend to corrode. In order to decrease the corrosion, the damage protective ("back up") anodic currents are applied during the period of interruption. The current work aims to establish the effect of the concentrations of sulphuric acid, copper and cobalt on the anode corrosion, to quantify the effect of various anodic protection levels on the anode corrosion and to propose a method to select the appropriate protective current density value.

Jan 1, 1999

By Klaus-Markus Peters, Robert M. Cravens, James G. Hemrick

"Degradation of refractories in molten aluminum applications leads to energy inefficiencies, both in terms of increased energy consumption during use as well as due to frequent and premature production shutdowns. Therefore, the ability to enhance and extend the performance of refractory systems will improve the energy efficiency through out the service life. TCON_ ceramic composite materials are being produced via a collaboration between Fireline TCON, Inc. and Rex Materials Group. These materials were found to be extremely resistant to erosion and corrosion by molten aluminum alloys during an evaluation funded by the U.S. Department of Energy and it was concluded that they positively impact the performance of refractory systems. These findings were subsequently verified by field tests. Data will be presented on how TCON shapes are used to significantly improve the thermal management of molten aluminum contact applications and extend the performance of such refractory systems.IntroductionThe production of molten aluminum creates aggressive environments for processing equipment, thereby requiring refractory materials to contain the aluminum during melting, transfer, treatment, and casting operations. Degradation of these refractories not only causes issues with reduced product quality and production yields, but also increases heat losses as the insulative properties of the refractories are compromised. Furthermore, in addition to disrupting production output, refractory failures lead to further impacts upon energy efficiency as large amounts of energy are lost during the cooling and subsequent reheating of the equipment as the refractory linings are repaired or replaced.The need for improved refractory materials is recognized throughout the industry. A joint U.S. Department of Energy and industrial workshop held in 2000 on applications for advanced ceramics in aluminum production [1] noted that refractory materials used in melt processing equipment have many limitations. The workshop report noted that these issues may be addressed by using advanced ceramics, but new materials must be cost effective when compared to current refractory materials. Also, in 2005 the Canadian aluminum industry produced a technology roadmap [2] having the goal of identifying and bridging gaps between current technological resources in the industry and future requirements. One of the areas identified as being crucial to the future of the industry was the need for improved molten aluminum-resistant materials."

Jan 1, 2009

By Tracy Morris, Weldon Read, Luis Navarro

"Bismuth is a recognized contaminant in the electrolytic refining of copper that can render many cathodes to be outside ASTM standards and unsuitable for copper rod and other downstream products if not carefully controlled. This paper portrays the performance of Molecular Recognition Technology (MRT) for bismuth removal at the Amarillo Copper Refinery (ACR) and describes how the highly selectivity gel has been successfully used to achieve good bismuth removal and how many pit falls and draw backs have been overcome.IntroductionASARCO operates one of the largest copper refineries in the world at Amarillo, Texas. The main feed for this refinery is produced at the Hayden smelter in Arizona. During the operation of this smelter a variety of metals are carried as impurities in the copper anodes because of the diversity of concentrates and residue products used as raw materials in the smelter feed mix. Even though the impurities are concentrated enough to be detected at the smelter, it is difficult to remove them completely. A simple way to control impurities at the smelter is to minimize the addition of material with a high concentration of impurities to the charge in order to reduce the output of this metal species. All this leads us to have a ""refinery problem"" [1,2,3]."

Jan 1, 2012

By F. Mucciardi

With the increasing trend to continuous smelting and converting, granulation of copper matte is gaining prominence as a means of decoupling the smelting and converting operations. Moreover, granulation is also being seen as a possible avenue to using higher grade oxygen in converters. By feeding cold solid matte, the oxygen concentration can be increased to compensate for the lower enthalpy feed. This leads to a higher grade of SO2 in the off gas and a lower total flow rate. Current granulation technology relies on the cooling of a falling matte film by water jets. This technology while effective has several drawbacks including those related to safety. Noranda and McGill University have developed a new process (patent pending) for solidifying copper matte (or slag). It overcomes many of the negatives of current technology. The system is based on an air cooled twin roll caster. This: new system uses no water and instead incorporates heat pipe technology to transfer the heat from the solidifying matte to the cooling air to produce a thin strip of 1 to 2 mm in thickness. Testing of a prototype unit demonstrated its viability. This paper describes this newly developed, twin roll casting system that is completely waterless. The advantages of this process as well as the findings from several tests are also detailed.

Jan 1, 1999

By María Guadalupe Sánchez-Loredo

Silver from nitrate aqueous solutions was extracted by commercial organophosphorous extractants (tri-n-butylphosphate, Cyanex 471x, Cyanex 301 and Cyanex 302). Quantitative silver extraction was obtained using the Cyanex reagents. After loading, aqueous solutions of several reducing reagents were used to prepare fine silver powders by reductive stripping. Only both extractants Cyanex 471x and tri-n-butylphosphate (TBP) could be reductive stripped and regenerated by aqueous solutions of ascorbic acid, and Cyanex 471x was decomposed to the corresponding phosphine oxide by using sodium borohydride as reducing agent. Silver was recovered as fine particles, which were characterised by means of scanning electron microscopy (SEM). Micrographs showed that the powder size and morphology were directly affected by the composition of the applied organic phases and aqueous reducing media.

Jan 1, 2003

By Staia. Mariana H.

Thermochemical equilibria of the heterogeneous system Ti-N-H-CI-Fe-Cr-Mo-Ni-Mn-C were calculated by using a commercial software based on the minimization of the free energy. Equilibrium calculations were done for temperatures varying between 800" and l 100°C and an initial molar relationship between reactants, a=NJTiCI,, of 0.1 to 2. The deposition process was considered to occur at atmospheric pressure. The activities of the alloying elements of the stainless steel were considered equal to their molar fractions. It was shown that for the conditions studied the substrate is no inert with respect to the gaseous phase. The existence of liquid chlorides was predicted for temperatures between 800" and 850°C and a ratio between 0.3 and 0.9. The most important metallic chlorides which appears to be present from the calculations in appreciable quantities in the gaseous phase are iron dichloride and manganese dichloride. In the low-temperatures zone and for low initial nitrogen contents, it result that the appearance of the liquid chlorides seems that partially inhibits the production of gaseous HCI. The highest deposition process efficiency calculated is obtained at a temperature 2 900°C and a N2/TiCI, ratios 2 0.7.

Jan 1, 1995

By M. Patel, A. W. Piper, R. A. Forsdick

"Lead bullion is refined in kettles to remove the contained impurities such as copper, antimony, silver and bismuth. These impurities are removed sequentially by the addition of one, or more, reagents to the bath. Impurity elements react selectively with the reagents to form a dross layer on the surface that is subsequently removed for further processing. Mixing the lead bath using specific impeller designs, which form a vortex to ensure that good contact takes place, carries out the reactions. It is important that the mixing is controlled to achieve the optimum bath conditions and hence good dross grades.This paper presents initial modelling work on the kettle refining process using both physical modelling (Water Models) and mathematical modelling (Computational Fluid Dynamics - CFD). Comparisons between measured plant data and simulation results are given.IntroductionThe refining of lead bullion takes place in hemispherical kettles of varying sizes. It is normal practice to remove the impurity elements sequentially, by the addition of reagents, which selectively react with the impurity element. The impurity element forms a dross layer on the surface, which can be removed for subsequent processing at the end of the reaction period.All the refining stages in the production of lead and lead alloys involve mixing the lead bath, although different conditions are required for each stage. At Britannia Refined Metals mixing is achieved using either 3 or 4 angled or flat blade impellers, which generate a vortex in the central region of the kettle. However, throughout the industry a wide range of mixer types are used which are all trying to achieve the same result."

Jan 1, 1999

By Marco V. Ginatta

Current world production, 60'000 ton/y, is exceedingly too small for titanium's extraordinary combination of favorable properties; it should be 1,000,000 ton/y (7% of stainless-steel). Prices that competitively sustain that sales volume are achievable only with electrolytic production, as it is for all other commercial nonferrous metals. But titanium does not have its commercial electrolytic plants yet, because of producers decisions and strategies, scientists works, industrial problems with chloride process, lack of consumers sponsors. Fluoride high temperature process has the advantages of aluminum electrolysis, plus other favorable characteristics specific to titanium and its feed material. One electrolytic titanium potroom replaces several different plants used for sponge production. Production of titanium ingots with zero defect is achieved. The solidified cathode rectangular slabs are suitable for direct rolling.

Jan 1, 2001

Copper and gangue mineralogy constitute the most critical parameters for the hydrometallurgical processing and cost-efficient extraction of copper. Minor changes in copper-, rock-, or alteration mineralogy can severely impact the comminution efficiency, curing, agglomeration, acid consumption, copper extraction and PLS impurity loading. Further, copper leach operations, particularly in the southwestern United States, are increasingly challenged by a combination of low grades and semi-refractory copper. This paper discusses the metallurgical and economical benefits of continuous mineralogical analyses in order to establish and operate a mineralogical data base in copper leach operations. Troubleshooting for copper extraction, integration of process mineralogy into production forecasting, and process optimization will be illustrated with operational experiences from Chile and the United States.

Jan 1, 1999

By Debbie Marshall

Nickel and cobalt in lateritic ores can be extracted by either a hydrometallurgical or a pyrometallurgical route. The high-iron limonitic fraction of a deposit is best processed' hydrometallurgically while the magnesium-rich transitional and saprolitic fractions are more suited for pyrometallurgical processing. During hydrometallurgical processing, it may be attractive, for economic reasons, to blend the limonitic component with transitional and saprolitic ores, which contain higher nickel levels. However, blending increases the concentration of magnesium in the feed, leading to increased acid demands. The decision on how much ore to process then becomes an economic one. Ore samples with different magnesium contents were prepared for the leach test program by blending limonitic and transitional ores. The ore samples were slurried in seawater and tested in the Falconbridge Hydrometallurgical Pilot Plant. As expected, acid consumption increased with increasing magnesium content of the ore. For target extractions of 95% nickel and 92% cobalt, the required residual free acid concentration increased from 30 g/L at 1.7% magnesium to 50 g/L at 2.7% magnesium. When the magnesium content was raised to 3.8% and 4.6% in subsequent pilot plant testing, the final free acid requirements did not increase beyond what was observed at 2.7% magnesium. Thus, the cut-off ore composition to maximize nickel units and minimize acid requirements is between 1.7- 2.7% magnesium. Keywords: high pressure acid leaching, laterites, magnesium

Jan 1, 2004

By Jimsher Aneli

The investigation of some peculiarities of conductivity dependence on filler type and amount in the polymer composites has been conducted. It is established, that conductivity of composites based on phenolformaldehide resin essentially depends on proportion of double fillers: graphite + carbon black, graphite+ andesite, contained in composites. It was shown, that these composites characterized by synergetic effect ? non additive influence of fillers concentration on the conductivity of composites. Some other properties of composites contained binary fillers (effect of temperature and pressure on the conductivity) have been investigated.

Jan 1, 2006

By A. G. Raraz

Reactive metal electrorefining presents a number of problems that pose obstacles to commercial operation. Cerium has been chosen as the surrogate for certain reactive metals because of its thermodynamic and electrochemical characteristics. A comparative review of the properties for cerium and plutonium has been presented to justify the choice of cerium as the surrogate metal for studying electrorefining. This review has addressed the electrochemical, thermodynamic, and kinetic parameters of molten salt electrorefining of cerium metal to provide an insight to this extremely important process. The cell components and configuration, current efficiency of the process, purity of the cathodically deposited metal and the power requirement of the system are evaluated for a molten CaCl2-MgCl2 salt electrolyte using a molten, stirred impure anode. Crucible designs, salt electrolyte, cell temperature and electrode materials are also evaluated. Selection of the salt electrolyte and the cell temperature have been suggested from this study.

Jan 1, 1992

By Christian Redl

"The Lattice Boltzmann Method (LBM) solves fluid dynamics problems based on a discrete mesoscopic approach. It is based on the Lattice Boltzmann equation which is a special discretisation of the continuous Boltzmann equation. Its principle advantage is that it can handle complex physical phenomena (like interaction between different components and surface effects), complicated boundary and initial conditions very well, free from many gridding and stability constraints that plague conventional numerical methods used for fluid flow simulations. Complex structures like porous media can be resolved directly. The LBM algorithm has a simple structure and acts locally, which is favourable for parallel computing. Its potential for metallurgical process simulation is demonstrated in the present study which is concerned with the simulation of the fluid flow in a copper winning electrolysis cell. The electrolyte is modelled as the carrier fluid and the oxygen is considered via a so called active scalar equation. The modelling of buoancy, momentum exchange and the free surface requires special effort. The results of the simulation are validated against experimental data obtained by Laser-Doppler-Anemometry. Despite the simplifications made, good agreement between the simulation and the experiments was found.IntroductionThe hydrodynamics in an electrometallurgical cell is a complex, highly non-linear phenomenon. It includes the simulation of a two component system with high density ratio, gravity driven flow and a free surface. A general solution to this problem is currently unknown.The flow field is a result of the combination of various hydrodynamic effects [18]. Metal deposition at the cathode yields in a decrease in the ion concentration, which reduces the density of the electrolyte. At the anode molecular oxygen is formed as a consequence of the oxidation of water molecules. The oxygen is solved in the electrolyte and again the electrolyte density is decreased. Both effects lead to a free upwards directed convective flow, refered to as natural convection."

Jan 1, 2001

By Ozgul Dere Ozdemir, Muge Sari Yilmaz, Sabriye Piskin, Deren Sibel Kasap

"Galvanic sludge is generated at the end of the waste water treatment process of metal plating system. The waste sludge is one of the main hazardous solid wastes produced by metallurgical industries. It is caused the harm of human health and damage of the environment due to containing reasonable amounts of toxic metals (e.g., nickel, zinc, copper, chromium, iron, lead, cadmium, etc). The concentration of those toxic metals in the wastewater might reach 30% (w/w, dry weight) making their removal and recovery an interesting issue.In this study, synthesized titanium dioxide is used as adsorbent to remove nickel in leachate of galvanic sludge. The adsorption experiments were carried out isothermally at four different temperatures. The effects of pH, temperature, and contact time on nickel adsorption efficiency were investigated, and the optimum parameters were determined from the experimental studies. The experimental results indicated that pH, temperature, and contact time played a significant role on the adsorption capacity of nickel.IntroductionRapid industrialization has caused increasing the heavy metal concentration in biosphere with the industrial wastes. These wastes are generated in various industrial processes such as electroplating. Galvanic sludge is a hazardous waste that generates from metal plating industry by chemical precipitation of heavy metals from acidic or alkaline solutions during the waste water treatment process. Heavy metals are tend to bioaccumulate thus they are treated the living organism [1-2].Galvanic sludge is mainly disposed on landfills for these reason it is a big problem for environment. Galvanic sludge containing nickel (II) is common because nickel (II) is used in electroplating process [3]. In drinking water, nickel may cause health problems if found in amounts greater than the health standard set (MCLG: 0.1 mg/L) by the United States Environmental Protection Agency (EPA). The higher concentration of nickel (II) in ingested water may cause severe damage to lungs, kidneys, gastrointestinal distress, e.g., nausea, vomiting, diarrhea, pulmonary fibrosis, renal edema, and skin dermatitis [ 4]. For these reasons, it must be treated before disposed to landfill."

Jan 1, 2011

By L. M. Bianchi

"Oxide, nitride and other compound coatings often do not have adequate properties for newer applications when produced using very high deposition rates and simple evaporation techniques. Solar control, abrasion resistance, low reflectance and barrier effective engineered coatings require exacting properties. Such properties can be obtained by adapting the activated reactive evaporation (ARE) technology to Web production processes. Adaptions of the HAD and MAD processes will be described along with data on the high deposition rates obtained. These fast production capabilities were developed in order to make the processes economically competitive.IntroductionThe Physical Vapor Deposition technique (PVD) has been used to coat steel strip for over 20 years. (1) However, its use as a production process has been very limited because of the high cost of the PVD coating process and because, in some instances, the properties of the coating were not good enough to meet the customers requirements. Nevertheless, the PVD process has found wide application in the airplane engine and electronic component markets. These production processes have stimulated further development and advances in the technology.In 1971, Profession R. F. Bunshah developed the Activated Reactive Evaporation (ARE) process which was then used to produce hard coatings such as carbides, nitrides, oxides and other refractory compounds. (2) The process from a fundamental viewpoint -produces a coating on the substrate via the evaporation of metal in the presence of a low pressure (typically around 1 millitorr) of reactive gas, with a plasma created in the space between the metal source and the substrate.The plasma may be created by many means but its function is two-fold. First, it activates the reaction between the metal vapors and the reactive gas atoms/molecules resulting in the formation of a compound that deposits on the substrate. Second, because the plasma is in contact with the substrate, it results in a negative bias on the substrate and produces bombardment of the growing film with ions and energetic neutrals from the plasma. This bombardment causes many significant changes in the microstructure, properties and appearance of the coating.Recently another new technology Pulsed Magnetron Systems (PMS) has been introduced into PVD. This new technology has been pioneered in production scale equipment by Dr. S. Schiller (3) and associates. The use of a pulsed power supply on the magnetron prevents the problem of the anode being coated with a insulating layer which will then lead to micro and macro arcing producing defects in the coating."

Jan 1, 1998

By H. Dijkman

The PAQUES Bio Systems' core technology, marketed under the name THIOPAQ®, consists of various high-rate biological processes for metal-sulfur-water systems, complemented with common solid/liquid and gas separation steps. Sulfur species are converted to sulfide, which is a valuable component as it can be used for metals reduction and precipitation. Selective recovery of valuable metals can be employed, leading to revenue from metal values. In this paper, biotechnological systems for the treatment of metal sulfate solutions and dilute SO, gases are described. These installations can be designed to either produce predominantly aqueous (NaHS) or gaseous (H2S) sulfide. The emphasis here is on hydrogen sulfide gas. The main case history discussed is the demonstration plant that ran on hydrogen gas at Kennecott Utah Copper. Three years of operating experience clearly show that sulfate reduction with hydrogen gas is a viable option. Furthermore, the selective recovery of copper from leach water with the hydrogen sulfide produced was shown to be very effective.

Jan 1, 1999

By Mingsheng He, Yunhui Tang

The structure and granularity of biological origin aragonite from abalone shell during wet grinding in a ball mill were studied with X-ray diffractometer, with morphology studied by scanning electron microscope (SEM). It is shown from the results that the particle sizes of aragonite decreased with grinding time, so did the X-ray diffraction (XRD) peak intensities, while the full widths at half maximum increased. A calcite XRD peak with low intensity and great width was observed in nearly all the samples with various grinding time, whereas the intensity of the peak increased obviously after grinding time 300 min. It is shown from the SEM results that the size of aragonite dropped with grinding time until it reached 20 nm and then kept constant, while that of calcite dropped first and then rose at the minimum about 10 nm until to the constant size as in aragonite. It was observed that the mineral content obtained from XRD show an obviously change that the calcite increases while aragonite decreases, which indicated the occurring of a polymorphic transformation of aragonite into calcite.

Mar 1, 2017

By Christian M. Sagedahl

The stringent environmental regulations for air pollution regarding emission control, along with the need of dry concentrates to feed autogenous smelting processes, are enhancing the development of cleaner technologies. Indirect drying of concentrates by a Kvaemer steam dryer is a technology with promising results, reducing dust entrainment to the exhaust gas stream and leading to smaller dust separation units. The Kvaemer dryers are designed for a very high availability, a high-energy efficiency, low amount and velocity of exhaust gases, no SO2, CO or CO, emissions combined with a wide range of satisfactory operating conditions and low total operational costs.

Jan 1, 1999

By A. A. Bustos

Four Air Liquide Shrouded Injectors (ALSI ) were installed and operated for over one year in a Peirce-Smith converter at the Falconbridge nickel smelter in Falconbridge, Ontario, Canada. A shrouded injector consists of an inner pipe and an annulus, through which high oxygen enriched air and nitrogen flow, respectively The nitrogen cools the injector and protects the refractory in the vicinity of the injector tip, allowing for substantial increases in oxygen flow rates to the converting reactions. Several injector designs were tested to study the effect of changes in the cross-sectional area and changes in the entrance geometry of the annulus. An optimum design would minimize the injection pressure required for a given flow rate to achieve choked flow conditions at the tip of the injector. The operation of the ALSI was simple and did not require any special care or maintenance, either between blows or between converter cycles. In particular, the shrouded injectors did not require punching, as is the case with conventional tuyeres. In terms of refractory performance, the ALSI, operating at 30-40 % oxygen enrichment, were superior or equal to the conventional tuyeres, which operated at 21-23% oxygen. The results of the demonstration program led Falconbridge Limited to implement the ALSI technology on a commercial scale The paper presents the demonstration program results in terms of gas flow rates, accretion formation, punchless operation and refractory wear.

Jan 1, 1999