Search Documents

By Barry J. Welch

The production of primary aluminium can potentially lead to metal that, with minimum treatment, meets a high purity standard. Smelters that can achieve a significant proportion of their production in this manner have a competitive edge which is of growing importance as the use grows for such items as compact discs and the like. Superimposed on the desire to produce high quality metal are stringent environmental requirements that the industry must adhere to. The environmental 'legislation focuses on fluoride emissions and the approach adopted is towards a zero waste management philosophy. The fluoride recycling process does, however, result in volatile impurities being captured and recycled to the cell. Aluminium has an extremely high reduction potential and this results in a significant proportion of the recycled impurities being reduced at the electrolyte metal interface and thus contaminating the metal. This paper reviews sources of impurities and the impact of the operating procedures adopted on metal treatment.

Jan 1, 1996

By Taegong Ryu

The thermal plasma process has been applied to the preparation of nanosized tungsten carbide (WC1-x). The reduction and carburization of the vaporized chloride by methane-hydrogen mixtures produced nanosized WC1-x powder, with a small amount of WC or W2C phase. The products were characterized using XRD, carbon analyzer, and TEM. The effects of plasma torch power, the flow rate of primary plasma gas (Ar) to generate plasma flame, and the addition of secondary plasma gas (H2) on the product composition were investigated. The tungsten carbide (WC1-x) powder had a particle size less than 30 nm. The powder was treated under hydrogen atmosphere to fully carburize the WC1-x, and W2C phases to WC as well as remove excess carbon in the product. Finally, WC powder with a grain size less than 40 nm was obtained.

Jan 1, 2008

By Jogre A. S Tenório

he aim of the present investigation was to investigate technological features of the Fe-NbC dissolution in liquid Fe-C alloys. Fe-NbC is a Ferro-niobium alloy with 7%C, has a particle size smaller than 150 pm and its micro constituents are polygonal niobium carbides and an iron matrix. The obtained dissolution time was less than one-minute and the yields were in the range of 80-90% at 1873 K. In the Fe-NbC dissolution process, the dissolution occurs at first, and as a consequence the niobium carbides become free to dissolve. These carbides will dissolve until the melt reaches a saturation point. The non-dissolved carbides remain trapped in the liquid or will form a dross. The addition yields decreases when the niobium concentration reaches this limit value, that depends on the carbon concentration. These define a saturation curve.

Jan 1, 1994

By Kim Verbeken, Evelien Van de Steene, Marc Verhaege, Jeriffa De Clercq

"AbstractThe industry is confronted with stricter discharge levels and an increasing awareness to avoid toxic waste (such as heavy metal containing sludge obtained in physicochemical water treatment) and recover valuable metals. This can be realized by ion exchange or by electrodeposition. Both techniques however show an optimum concentration range to efficiently remove and/or recover metals: electrolysis can recover the metal in its metallic form but suffers from low efficiency when applied to diluted solutions, whereas ion exchange can only be applied economically in the low ppm range.A combination of ion exchange followed by electrodeposition was applied to an industrial wastewater. The strong acidic ion exchange resin was stripped with H2SO4 giving a solution of 9g/L nickel. From this solution, nickel was electrodeposited in an ammonia buffer on a Ti-mesh cathode with high current efficiency. It is shown that organic compounds (surfactants, brighteners, …) present in the industrial wastewater do not influence the recovery process.IntroductionAlmost all rinse waters emerging from metal plating plants are generated during the washing operation of plated materials. These solutions with low metal content must either be recycled within the process or be discarded to the surface water after decreasing their metal content to acceptable levels determined by the local environmental regulations, which become more and more stringent. Today, the most commonly used practice is a physico-chemical treatment (precipitation) and a resin post treatment to meet the standards. A more sustainable approach should use a technology to recover efficiently the metal or metal salt without the production of sludge and the effluent should be consistent with environmental regulations."

Jan 1, 2008

By David J. Kinneberg, Barbara E. Mangion, Arnold M. Savolainen

Analytical laboratories require a qualitative or semi-qualitative method of determining major and minor constituents in "unknown" samples to select optimal analytical techniques. This is exceedingly important in precious metal assay laboratories where the precision and accuracy requirements are exacting (routinely within 0.02%, absolute basis). This paper describes the use of an x-ray fluorescence spectrometer with a specially designed software package to select optimal analytical procedures and specify relevant analytical parameters. A wavelength dispersive XRF spectrometer is capable of quick and accurate analyses of properly prepared samples without extensive standardization. When coupled with a specially designed software package, this preliminary assay system is applicable to a wide variety of sample types including gold and silver bullion, karat gold and karat PGM alloys, high silver and high copper metallic samples as well as particulate samples of ores and sweeps. The system relieves the assayer of tedious calculations for silver inquartation and proofing, minimizes human error and standardizes selections over time. Most importantly, the system allows for independent verification of final assay results.

Jan 1, 1999

By I. A. H. Schneiderl

Eichhornia crassipes approaches being a scourge in many parts of the world, .choking waterways and hindering transport upon them. At the same time it is known to readily abstract heavy metal ions from water and, thus, aids in the removal of heavy metals found in such waters. This paper considers the possibility of using specific parts of the plant as an inexpensive adsorbent for the removal of heavy metals from contaminated chemical and mining industry waste waters. In particular the root of the plant was found to be an excellent accumulator of 'heavy metal ions including uranium from solution. It is. also suggested that dried roots of the plant ?might be placed in simple bags and used in a very low cost metal ion removal system.

Jan 1, 1995

By Frank Field, Randolph Kirchain, Elisa Alonso, Richard Roth, Nathan Fleming

"High material prices and price uncertainty can be harmful to manufacturing firms. Increased use of recycled materials, industry-wide, can lower both material prices and price variability; moreover, increased recycling decreases the use of primary material, which mitigates price increases due to scarcity effects. These stabilizing and price lowering effects are explored using an Aluminum industry model. We show that (a) increased recycling leads to smaller price fluctuations in the presence of a primary metal supply perturbation, and (b) that the more substitutable the secondary metal is for the primary metal, the lower the overall material price is.IntroductionThe price of an industrial metal is expected to be a function of both the marginal cost of extraction and its scarcity[l-2]: where scarcity can be defined as the degree to which anticipated demand exceeds the known supply. Recycling end-of-life metal increases the apparent supply of the metal, or-in a functionally equivalent, but alternative conception-lowers the demand for primary metal; this lowers primary metal scarcity and should, theoretically, reduce its price. To the extent that this theoretical prediction holds true, recycling can provide benefits to consumers of industrial metals in the form of lower prices.Using a platinum industry model, prior work by Alonso[3] has shown that increased industrywide recycling can reduce metal price volatility because the secondary metal production (a) offsets virgin metal depletion, and (b) responds to supply-demand balance fluctuations more rapidly than the primary market. However, Platinum is not a typical industrial metal in the sense that secondary metal is perfectly substitutable for primary metal: Both primary and secondary platinum metal are functionally equivalent and have a common price. Other metals, such as secondary aluminum which is used as an example case in this study, contain varying degrees of other elements that were either intentionally added, or were inadvertently mixed in with the metal during the scrap recovery process. Consequently, different grades of scrap exist that have different profiles of elements in their composition. Depending on their particular profile of elements, more or less of a given grade can be used as a mass fraction of the final alloy-the secondary metal is not perfectly substitutable for the primary metal. For the purposes of this paper, the aluminum mass fraction of the final alloy that can be made up of secondary aluminum is termed the secondary substitutability of that grade in that alloy."

Jan 1, 2011

By L. Z. Villanueva

An investigation and evaluation has been performed to determine the potential utilization of electron beam irradiation technology for sulfur oxides removal from reduced-S02-strength metallurgical gases from copper smelters. These off-gases, though too weak to be converted to usable, concentrated: sulfuric acid by conventional means, are characterized by SO2 content higher than 2,000 ppm and a complex chemical composition, including high oxygen content and its generation occurring in a cyclical, fluctuating pattern. This work was based on information supplied by principal smelter companies in Chile. A laboratory facility with flow rate of 20 Nm3/h and equipped with an electron accelerator of beam energy 8.00 keV, has been used for testing. Influence on SO2 removal efficiency of operational parameters such as gas temperature, water vapor content, ammonia feed ratio and irradiation dose was established. The main conclusion of this work, from experimental laboratory tests as well as engineering studies, is that the Electron Beam Process (EBDS) is a cost-effective, simple and appropriate chemical process means for emission abatement. EBDS can, on a site-specific basis, adequately augment SO2 removal to upgrade overall abatement as required and in an optimal manner.

Jan 1, 1999

By Bekir Karasu

Boron raw materials are amongst the most important natural sources for many industrial branches and their values become increasingly raised with the discovery of boron usage in many new technological fields. All the countries in the world are unfortunately not as lucky as Turkiye and USA where major boron deposits are mainly located. It is widely known fact that on one side, boron is very precious component with its technological importance, on the other; only its limited sources are available. Therefore, even its wastes have to be evaluated and regained. In the present work wastes of Etibor Kirka Borax Company of Turkiye were used in the production of opaque frits which was suitable for floor tile glazes. Standard and newly produced frit based glazes were applied on the pre-engobed floor tile bodies and single firing was employed. Final products were examined according to the certain standard tests and their microstructures were also investigated. All the results confirmed the evaluation of boron wastes in opaque floor tile glazes.

Jan 1, 2006

By Paul Dewison

For nine years, from mid-1987 to mid-1996, the copper market enjoyed what appeared to be an endless boom in which prices were much higher relative to production costs than for most other base metals. After the boom ended abruptly mid-1997 with the Sumitomo affair, copper was burdened by an overhang of new projects that promised to swamp demand in what, with the Asian financial and economic crisis of 1997, had become a considerably worse consumption environment. Now, demand prospects do not look so bad. If, as we suspect, we will be dealing with a more rational market in the future, it becomes all the more important to forecast accurately the prospects for consumption. In this paper, we present a new methodology for copper demand forecasting. The methodology forms the backbone of the demand-side analysis for the multi-client study entitled "Long Tenn Outlook for Copper", co-authored by Metalica Ltd. and Bloomsbury Minerals Economics (BME). Key components of the methodology are as follows. (1) Relate demand to economic structure. (2) Focus on products rather than refined consumption. (3) Apply a consistent products/applications analysis to all countries and time series. (4) Incorporate scrap market dynamics within the analytical framework.

Jan 1, 1999

By A. J. Rigby

Current practices employing porous plugs to inject nitrogen into molten copper during primary smelting are described. Nitrogen stirring increases heat transfer to the bath, eliminates temperature stratifications, and improves efficiency during the steps of desulfurization and deoxidation. The opportunity to use porous plugs as the means to introduce reducing gases to deoxidize copper is also discussed. Previously reported laboratory results using porous plugs, which point to very high utilization efficiencies of hydrogen when used as the reducing gas, are again reviewed. Advances in the design of the porous plug, and the introduction of a system enabling external replacement of plugs is also discussed.

Jan 1, 1999

By J. W. Tsai

Both diamond crystals and diamond films were grown on silicon and copper substrates using a methane/hydrogen gas mixture as a precursor with thermal CVD techniques at low pressure environment. In addition to diamond particles, other crystalline phases including graphite and aluminum silicon carbide were observed on the substrate surface. ?The grown materials were analyzed with X-ray diffraction, electron microscopy, Auger electron spectroscopy and optical microscopy. Most synthesized diamond crystals were twinned. The flow rate of reactant gases, substrate nature, substrate temperature, decomposition temperature of the precursors, total pressure of reaction chamber, methane/hydrogen ratios and other possible parameters were varied during the growth processes, and the significant effects of these factors on nucleation and growth rate were evaluated.

Jan 1, 1989

By Emil H. Geus

A process has been developed to recover aluminum from dross which does not require the use of salt flux as commonly employed, This results in a salt-free residue which has potential industrial uses or alternatively can be safely land-filled. The dross is first heated by an air-fuel or oxy-fuel burner in a sealable rotary furnace. At a suitable temperature the burner is turned off and the temperature of the dross thereafter controlled by means of an atmosphere of oxidative and inert gases. When the free metal has agglomerated it is first discharged from the furnace, followed by the residues.

Jan 1, 1995

By F. Tanaka

In April 1999, a two-year campaign of the Mitsubishi furnaces was achieved at Naoshima Smelter; the present one is expected to be extended much longer. An overview of basic technology for decreasing refractory wear in the Mitsubishi Process is presented. One of the main features of the process is the use of top blowing lance technology which has a different effect on the furnace refractory than other conventional processes. The refractory wear of concern is hearth wear caused by top blown powder injection, wear of the side wall caused by splashing droplets, and wear of the bath level refractories caused by surface waves of melts in the furnace. These have been systematically investigated for many years. This paper describes the results of various model tests and their application to practical furnace design and operation.

Jan 1, 1999

By A. L. Davies

The MTDATA computer software package consists of a rigorous implementation of an algorithm for calculating chemical phase equilibria by the technique of Gibbs free energy minimization and a database of the thermochemical properties of common materials, such as slags, mattes, metals, gases and aqueous solutions. We have used MTDATA to contribute to our understanding of the chemical reactions occurring in several specific unit operations of the Kennecott Utah Copper Garfield Smelter. The following two examples illustrate the range of environments to which the method is applicable. Calculation of the liquidus phase relations of the FSF fayalite and FCF calcium ferrite slags helped in the early diagnosis of several operating problems. Calculation of the deportment of fluorine between the FSF offgas and the FSG scrubber liquor helped in the identification of operating conditions under which significant hydrogen fluoride concentrations could be introduced to the contact section of the acid plant. Without the painstaking assessment of solution phase properties undertaken over many years, these calculations would not be possible.

Jan 1, 1999

By Junfu Chen, Jiann-Yang Hwang, Yong Zhou, Lijun Lu, Likun Lia, Jixiong Liu

The sheet-like NiS-ZnS heterostructured composites were prepared by the microwave hydrothermal. The fabrication of the heterojunctions broadened the range of light response of ZnS. The photoexcited electrons of ZnS migrated to the redox potential of NiS/Ni2S under visible light irradiation, which can facilitate the effective separation of photogenerated electrons and holes in space. The visible photocatalytic activity towards hydrogen production for NiS/ZnS nanosheet heterostructed composites without co-catalyst achieved 0.28 mmol h–1, and the quantum efficiency was up to 18.6% under the wavelength with 420 nm visible light irradiation.

Jan 1, 2015

By Tomas Astorga

APEC, the Asia Pacific Economic Cooperation is the forum of 21 countries having approximately 56% of the total world income, and over 45% of global trade. In 1997, APEC economies produced 67% of the world copper output, 55% of gold, and over 45% of other base metals. Mining in APEC captures more than 60% of the total mining investment in the world. New and emerging economies are now appearing in the demand scenery, such as China. New trends in the international environmental regulations are posing questions related to the use of copper in different industrial and consumption applications. These may have a strong impact on future trade of copper. New applications are also appearing based in new technology fields. The paper examines the growth potential of the copper market in main consumer ad highly populated economies of APEC, incorporating analysis of various interrelated factors. It also analyses the outlook of the copper supply. Its conclusions point to the need to implement demand outlook models. Finance and economic reforms will open important avenues for trade growth in basic metals, particularly copper. Changes in the consumption patterns of highly populated countries will add to better perspectives of copper demands. The recovery of a fast pace of economic growth in the APEC region will bring new demands for copper, especially as a consequence of high tech applications. More extended policies focused in the need for developing energy efficiency programs and schemes will add to this picture.

Jan 1, 1999

By Shengli Wu, Mingyin Kou, Feng Chang, Laixin Wang, Hua Lu, Jianliang Zhang

Sintering dust has been regarded as an important secondary resource in a modern steel plant. Sintering dust was mechanically treated using different milling machines and experimental conditions in air atmosphere. The changes in phase constitution, particle size, specific surface area, particle morphology, and lattice parameters of activated sintering dust were determined. It was found that the agglomeration of the particles take place during extended dry milling with accessible pores for Nitrogen gas. The maximum specific BET surface area in the stirring wet grinding and planetary wet grinding increases to 43.06 and 46.45 m2/g after activated 360 min respectively. With the increasing of energy input, the intensity of diffraction peaks of dolomite and hematite gradually decreased. Furthermore, the previous phase almost disappeared eventually under any experimental conditions. In addition, Fourier transform infrared spectroscopy indicates that organic matter and carbonate decompose easier than other phases, especially under stirring wet milling.

Jan 1, 2016

By Jin-Chun Kim

Nanosized W based powders (W, WC, WC-Co) were produced by chemical vapor condensation (CVC) process. Two different solid W(CO)6 and Co2(CO)8 metal-organic materials were used as precursors. CVC experiment was conducted in the temperature range of 400-1100. As-CVC WC1-x powder which had non-stoichiometric composition was carburized by using of the CH4-H2 mixed gas in temperature range of 750-850. The CVC W and WC1-x powders showed loosely agglomeration structure, and the Co powder had intricate long stand structure because of intrinsic magnetic properties of Co phase. Carbon content of the CVC powders controlled by gas-phase carburization was well matched with theoretical WC stoichiometry (6.13wt%).

Jan 1, 2006

By Kazuaki Mita

There are various intermetallic compounds in the Zn-Fe system. We synthesized them at about 673K. A specimen was examined chemically and X-ray diffraction was applied to ensure the formation of intermetallic compounds. Material containing two phases was placed in a Knudsen type effusion cell and the mass spectrum studied to evaluate the vapor pressure of zinc. The thermodynamic properties of intermetallics was then evaluated through measured intensity.

Jan 1, 1999