Search Documents

By Mariane Costalonga de Aguiar, Carlos Mauricio Fontes Vieira, Sergio Neves Monteiro

"This work evaluates the effect of incorporation of an ornamental rock waste into an industrial clayey body used for roofing tiles fabrication. Formulations with 0, 10, 20 and 30 wt.% of waste were prepared by replacing the sand in the industrial clayey body. The plasticity of the formulations was determined by the Atterberg limits. Specimens were fabricated by 18 MPa press-molding and then fired from 850, 950 and 1050°C. The specimens were tested to determine the water absorption, linear shrinkage and three points bending flexural strength. The results indicated that the waste improves the extrusion performance of the clayey body by decreasing its plasticity. The use of the waste was beneficial to the water absorption and mechanical strength of the fired clayey ceramic at 1050°C.IntroductionOrnamental rock is a natural resource available in the municipal area of Santo Antonio de Padua and located 150 km from the city of Campos dos Goytacazes, northe of state of Rio de Janeiro, Brazil. Intense industrial activity related to ornamental stones, especially gneisses, is traditionally occurring in the region. After mining, the flagstone is submitted to sawing to obtain blocks and then, after a manual operation, the final products are small flagstones [1,2]. During the sawing operation, a sludge composed of water and fine particles of rock is generated. A monthly production of 1000 tons of ornamental rock waste is estimated to be produced at Santo Antonio de Padua. The final disposal of this waste has brought serious environmental problems. Since most industries do not have an adequate sludge treatment, the waste is contaminating the soil and underground waters as well as obstructing rivers and lakes.Ceramic bodies industrially fabricated in the municipal area of Campos dos Goytacazes, 280 km from the city of Rio de Janeiro, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral, associated with high plasticity. Due to the excessive plasticity of the ceramic bodies, it is common to have dimensional defects in the final products after the drying and firing processes. Moreover, the kaolinitic structure and the presence of aluminum hydroxide confer a refractory behavior to the local clays. This impairs sintering during the firing operation. In the case of clay ceramics for civil construction, this results in greater porosity associated with elevated values of water absorption [3,4]. To avoid this problem, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative."

Jan 1, 2011

By H. Y. Sohn

A novel solvent extraction process in which the emulsion is generated by bottom gas injection rather than mechanical stirring has been developed. This process has a number of advantages over the mixer-settler unit or the spray column in terms of simple equipment configuration and the ease of cleaning and process control while providing a large interfacial area for mass transfer. The equipment consists of a horizontal cylindrical vessel in which the two immiscible liquids flow countercurrently. High-strength gas jets are injected from the bottom at certain intervals along the length of the vessel. The gas jet creates a plume zone consisting of an emulsion of the two liquids which contains a large interfacial area for rapid mass transfer. The two liquids then disengage and flow in the opposite directions before entering another plume zone. Thus, the process combines the simplicity of a cylindrical vessel, having no moving parts, with the contacting efficiency of a mixer-settler. The gas can be recycled in a closed loop, thus eliminating mist and other emission problems. These advantages would be especially significant for treating large-volume/low-value liquid streams which contain hazardous substances and/or suspended solid particulates.

Jan 1, 1996

By Jiangwei Shen, Cong Wang, Haibin Zuo

The research on the formation of Silico-Ferrite of Calcium and Aluminium (SFCA) in the process of cooling and solidification is rarely reported. The crystallization process was observed by using scanning electron microscopy (SEM) and optical microscope in this paper. The effect of different cooling system on the microstructure and phase composition of the sinters was investigated to obtain the appropriate cooling rate to improve the metallurgical properties of sinters. The experimental results show that the crystallization of calcium ferrite is getting better when the cooling rate is decreased from water quenching to cooling in the air. There are a large number of hematite phases with interconnected crystal structure in the sample cooled in the air. In the case of the compressive strength, it was determined by the mineral composition and pore structure, higher SFCA and hematite contents in sinter cooling in the air lead to a higher strength. Glass phase in the water quenching sinter was the major reason for the lowest strength. High porosity contributes to a decrease in compressive strength for the sinter cooling in the furnace. Therefore the air cooling was the appropriate cooling rate to achieve high quality sinter under this experimental condition.

Jan 1, 2016

By Ying Qin, Shujing Zhu

The characterization of adsorption of natural and composite bentonite in lead aqueous solution has been studied. The results showed that adsorption of both natural and composite bentonites strongly depended on the pH values of the solution. At lower pH values, the mechanisms that govern the adsorption of bentonites were dissolution of crystal structure and competition between the metal ions and the H+. To composite bentonite, the lead ion removal capacity was close to 250 mg/g. At higher pH values, formation of lead hydroxyl species might lead to either participation to the adsorption or precipitation onto the bentonites. Hence, a rapid increase in the equilibrium removal capacity of lead was obtained when pH > 7.0. An increase in the initial lead ion concentration led to the increase in the equilibrium adsorption capacity increased to a certain degree; and then, a plateau was obtained at higher concentrations. As a result, the adsorption performance of composite bentonite was better than the natural bentonite in both physical and chemical changes. The data fitted well with both Langmuir and Freundlich isotherms.

Mar 1, 2017

By H. Y. Sohn, Y. Mohassab, D. Q. Fan, M. Elzohiery

A flash ironmaking process is being developed at the University of Utah in which iron is produced directly from magnetite concentrate. The kinetics of magnetite reduction by a mixture of H and CO gases was determined in the 2 temperature range 1150–1600 °C. Over 90% reduction degree was achieved at a temperature as low as 1250 °C within 4–6 s which is the typical residence time available in a flash reactor. The kinetics results were applied to experimental data obtained in a laboratory flash reactor in which H and CO gas mixtures were 2 produced from in situ partial oxidation of natural gas with oxygen. CFD was used to simulate the laboratory reactor,and the results were in good agreement with the experimental data.

Mar 1, 2017

By Li Kaihua, Li Liang, Miao Qingdong, Wang Cong

The current process of production of titanium sponge involves the use of TiCl4 as a feed material and a huge amount of heat is generated during the magnesiothermic reduction process. For this reason, it is possible to agglomerate into a titanium lump with the partial high temperature. And, it is difficult to obtain soft titanium sponge with low content of impurities. In order to solve the current problems in the titanium sponge production process, process optimization experiments study of TiCl4 feeding speed, vacuum distillation temperature, system pressure and time control had been conducted for obtain high quality titanium sponge. Experimental results show that lower feeding speed can improve the output capacity of titanium sponge and softer products can be obtained. The product grade rate of titanium sponge improved significantly.

Jan 1, 2015

By Suzzann Nordwick

Over the past decade, significant advances have been made in the development of sulfate-reducing bacteria (SRB) technology to treat acid mine drainage (AMD). Bench-scale testing, field demonstrations, and engineered applications of SRBs for the treatment of AMD will be presented. Designs include an in situ bioreactor installed in the subsurface workings of the Lilly Orphan Boy Mine in 1994, the SRB bioreactors installed at the Calliope Mine from 1998 to 2001, the integrated biological reactors built at the Surething Mine in 2001, and the ongoing development of a replaceable cartridge system. SRB technology benefits include the reduction of dissolved metal ions to insoluble metal sulfides and the neutralization of the AMD resulting from the production of bicarbonate from the oxidation of organic nutrients. This paper will address engineering design criteria including the selection of organic media and system permeability and complete mitigation of AMD. Research was funded under Interagency Agreement No. DW899388-70-01-1 between the US EPA and the US DOE and was conducted by MSE Technology Applications, Inc., through the National Environmental Technology Laboratory (DOE Contract No. DE-AC22-96EW96405) at the Western Environmental Technology Office located in Butte, Montana.

Jan 1, 2003

By Cynthia K. Belt

Improved energy efficiency has grown in importance within industry as energy costs have escalated. The analysis of trends and changes to a process is critical in making the best business decision in energy management. Frequently, energy use per day (Kilowatt-Hour or British Thermal Units) is used to track energy efficiency. Sometimes, the somewhat more complex method of energy per processed weight (Kilowatt-Hour per Metric Ton or BTU per Pound) is used to make this evaluation. Yet both methods ignore the effects due to throughput and weather. In this paper, different thermal processes and systems will be evaluated using statistical methods to highlight alternative methods to evaluate energy efficiency. Examples and potential problems will be discussed for both a single process and a collection of processes within a plant or corporation.

Jan 1, 2008

By David B. Dreisinger

The total pressure oxidation treatment of arsenical copper ore and concentrate from the El Indio mine of Banick Gold was tested in benchtop autoclave treatment. The concentrate oxidation typically achieved ~95% copper extraction. Copper extraction was limited by the reprecipitation of a complex precipitate containing arsenic. Gold extraction by cyanidation of the oxidation residue was around 95%. Silver extractions were less than 10% due to the formation of argentojarosite in the autoclave. The total pressure oxidation of the whole ore sample was more successful. Copper extractions of 98-99% were routine achieved. Gold extraction by cyanidation was +95%. Silver extraction could be increased to as high as 95% by using the lime boil treatment. A process flowsheet was proposed based on the results achieved. Copper recovery was proposed by direct solvent extraction and electrowinning of copper by treating the dilute solution from the autoclave discharge.

Jan 1, 1999

By M. Rubinstein, N. C. Koon, B. N. Das, V. G. Harris

"Copper and gold - based alloys having giant magnetoresistance properties were produced by melt spinning from arc melted and cast rods. The ribbon width varied between 1 and 2 mm and the ribbon thicknesses were in the range of 30 to 50 11m. The uniform microstructure of the cast rods indicated the composition homogeneity in the starting material. The ribbons showed composition uniformity across the cross section from EDX analysis. However, the spun ribbon microstructure changed from a 'frozen in' region near the wheel side to a nanosize spherically precipitated phase towards the freely frozen surface. The evolution of the microstructure from the spun ribbon state to the annealed ones was studied by optical microscopy, SEM and TEM. The structural information of the spun and annealed specimens was obtained from X - ray, electron diffraction, electron microscopy and ferromagnetic resonance. Magnetoresistance was measured by the four point probe method.IntroductionRecently. Giant Magnetoresistance. GMR. has been observed in sputtered thin films alloys of Ag. Au and Cu with Co and Fe [1. 2. 3]. The sputtered films are produced by condensation of the alloys from the vapor phase. These Ag. Au and Cu alloys are miscible and homogeneous in the vapor and liquid phase (except Ag alloys which exhibit phase separation even in the liquid phase) but immiscible and heterogeneous in the solid phase. In our work we have produced thin ribbons of the Cu and Au alloys about 30 µm thick from the miscible state in liquid phase by rapid solidification melt spinning. The microstructural development of the ribbons was investigated in the as - spun condition and on annealing. The other properties such as magnetization. GMR and Mossbauer Spectroscopy were also investigated in the various microstructural conditions of the ribbons."

Jan 1, 1994

By Srinath Viswanathan, Zhijing Zhang, Ramana G. Reddy

"The viscosity measurements were carried out on melts of 380 aluminum alloy containing 20 volume % SiC particulates under various shear rates at different temperatures using a Brookfield viscometer. Results showed that viscosities of the melts increased with decreasing temperature and decreased with increasing shear rate. These results were compared with those of 356 alloy and it was found that the temperature had a more significant effect on viscosity of 356 alloy than that of 380 alloy containing SiC particulates. Based on the present experimental data an empirical viscosity model, which considers the effects of both solid fractions in the melt and shear rate, is proposed.IntroductionDiscontinuously reinforced metal matrix composites materials (MMCs) such as aluminum alloy containing SiC particulates have considerable potential for applications in the automotive industry because of their superior stiffness, higher specific mechanical properties, better dimensional stability and strength retention at elevated temperatures when compared to their monolithic counterparts. They have a great advantage in the specificity of their properties, meaning that specific materials can be engineered for specific applications. With such freedom of design, materials engineers have to accumulate a very large database of mechanical properties. Among these properties, the viscosity of alloy slurries is very important for producing, casting and forming process of metal matrix composites materials because viscosity has a decisive influence on fluid flow. The understanding of the rheological behavior of alloy slurries is necessary for these materials to become economic reality. Therefore, a study was carried out to measure the viscosities of 380 aluminum alloy containing 20 volume % SiC particulates under various shear rates and temperatures. In addition, a viscosity model representing the primary features of the alloy slurries was developed."

Jan 1, 1999

By S. Street

The Environment process, invented by Prof. H.K.Womer and developed at the University of Wollongong, simultaneously treats ferruginous and organic wastes via bath smelting. Conceived in the late 1980's, the patented process was originally developed using steelworks dust to settle solids from sewage, producing a composite material suitable for smelt reduction. Work began on the process in 1990 with the Australian patent having a priority date of February 1990. Early research focussed on settling of solids from sewage, while pyrometallurgical investigations examined smelting in small induction furnaces. By 1992 smelting trials had been undertaken in pneumatic and electric arc furnaces, the process being successfully demonstrated up to on 8 tonne scale. The success of this particular trial, and other smaller trials, resulted in construction of a 100kg DC arc furnace which was commissioned in 1993. By 1994 the main project focus was on development of the smelting technology. Over 3 years of trials on the DC arc furnace have identified and clarified many of the pyrometallurgical reactions. optimum operating parameters, as well as demonstrating the versatility of the process for treating a wide range of wastes. Currently the Illawarra Technology Corporation (lTC), the commercial arm of the University of Wollongong, is pursuing commercialisation of the process.

Jan 1, 1996

By Felipe Daroch, Maria C. Ruiz, Rafael Padilla

Copper concentrates with high arsenic contents must be pretreated before conventional smelting to prevent environmental pollution with arsenic compounds. In this work, experimental results concerning the selective removal of arsenic and antimony from copper concentrates are presented. The process consists of an alkaline digestion using concentrated NaHS-NaOH solutions to transform the arsenic and antimony sulfides into soluble compounds. A water leaching follows the digestion to dissolve the arsenic and antimony, leaving clean copper sulfide solid residues. The laboratory scale tests were carried out using a copper–arsenic concentrate with 15.05% As and 1.42% Sb. The results showed that the most important digestion variables were temperature and concentrations of NaHS and NaOH. Over 97% of arsenic and 92% of antimony could be removed in 10 min of digestion using 8.9 M NaOH and 100% excess of NaHS at 80 °C. The subsequent water leaching was performed at 80°C for 20 min.

Jan 1, 2015

By Alexander I. Raitchenko

"An electroconductive viscous liquid may flow in laminar or turbulent regime under Lorentz-force generated by the intercrossed electric current and magnetic field. When there is a starting flat layer between hard and free boundaries with surface tension the spatial Lorentz-force can create a specific stationary regime of flow: the plane free surface will transform into the wavy one, and the movement in the depth will be not laminar and not turbulent, but this regime will be characterized by organized forms with indications of ""rolling of long cylindrical drops"". Wave-length is determined by the viscosity, the density, the surface tension, the average thickness of layer, and Lorentz-force. ·The limit of wavy regime is determined by most long of wave which is directly proportional to the critical value of specific flow and inversely proportional to the kinetic viscosity. The proper critical value of Reynolds number is determined by the dimensionless combination containing surface tension, density, viscosity, and Lorentz-force. The mentioned dimensio.nless combination in our case is some criterion substituting the known Kapitsa number for case of the thin viscous liquid layers under gravity. Spreading of admixture by mechanism of wavy regime is more rapid than by common diffusion or by laminar flow. The suggested conception can be a contribution into the theoretical basis for elaboration of some specific liquid metals technologies."

Jan 1, 1999

By C. Segawa

SMM operates an original slime treatment process for recovering precious metals and other metals (Te,Se,Sb,Bi)from the copper and the lead anode tankhouse slimes. In recent years, the amount of slimes has increased and the pyrometallurgical processing units capacity became the bottleneck of the entire plants. For the expansion of the plant, new pyrometallurgical facilities, incorporating a BBOC, was commissioned in 1992 and has now been successfully operated. In addition, unit operations were optimized to increase recovery and reduce operating cost .. The results of modifications made in the plant are discussed in this paper.

Jan 1, 1996

By A. K. Kyllo

The use of Composite Furnace Module cooling systems has been shown to give improved refractory performance in a number of above bath locations in WMC flash furnaces. To test the behaviour of modules in contact with a melt, a set of instrumented modules have been installed in the reaction shaft of a. nickel flash furnace. The location was chosen to provide a suitably harsh environment to ensure rigorous testing, while still allowing relatively easy access for module installation. The modules were continuously monitored to provide information on the module performance, as well as the temperature in the shaft itself. The shaft temperature showed significant transient behaviour, which resulted in heat fluxes through the modules ranging from 10 to 92 kW m-2. The modules were capable of handling the highest heat flux with no risk of the coolant boiling. This paper details the design and operation of the modules over a period of seven weeks.

Jan 1, 1999

By Robert W. Bartlett

Chalcopyrite in copper flotation concentrates can be hydrothermally converted to digenite with oxygen in a continuous process, with rapid kinetics when operated above 200°C. This eliminates large amounts of sulfur and iron. These "super-concentrates" have potential for debottlenecking smelters and avoiding capital intensive future smelter expansions, otherwise required in the late 1990s. The technology of producing super- concentrates is described, with cost estimates, and the use of super-concentrates as smelter feed is discussed, with examples.

Jan 1, 1992

By Alex Probst

With low metal prices and increasing value placed on plant water and tailings disposal areas, it is becoming essential to maximize the efficiency of solid-liquid separation processes. Since its inception over 25 years ago, the use of flocculants has grown exponentially. While flocculants play a crucial role in the sedimentation process, they are also a major operating cost. Recent innovations are revolutionizing the industry once again. New thickener designs are doubling thickener-loading rates while reducing flocculant consumption. The feedwell, as the heart of the thickener, is undergoing many significant metamorphoses. With CFD and other advanced computational analysis, feedwell technology is being examined more thoroughly than ever before, The result is that the thickener previously thought of, as a "Black Box" is now being mapped and controlled with state-of-the-art technology. This paper will examine recent design improvements in all aspects of thickeners in order to project the look of the thickener of tomorrow.

Jan 1, 1999

By W. Mueller

The function of a process mineralogist in the operation of a copper mine and plant is to assist in the identification and classification of the operation's main throughput. These include ore, concentrates, slag and matte, and to a lesser extent, refined products. In addition, a number of other products not normally thought of in association with mineralogy are examined. These include scales from submersible pumps, failed boiler tubes, acid plant, and shaft furnace; characterization of inclusions in failed compressor gear teeth as well as in copper rod; and flue dusts from a smelter, air transported particulates and coatings on passive copper anodes in the refinery. Techniques and equipment required for these studies include simple hand magnets to the high intensity Isodynamic separator, visual examination to electron microscopes, x-ray equipment, DTA, IR, heavy liquid separation, and contracted services of custom laboratories. Several examined products from Magma Copper Company have been selected to illustrate the range of techniques and equipment required by a process mineralogist.

Jan 1, 1981

By B. R. Adams

This paper discusses the use of a reacting CFD model to determine chalcopyrite kinetics in a drop tube furnace and to predict the reaction of a chalcopyrite concentrate in the reaction shaft of an industrial smelter. Reacting CFD codes can be applied to determine the consequences of the interaction of gas with particles and therefore improve the ability to derive kinetic parameters that take into account the temperature and oxidation histories that different particles will see. This paper describes the application of such a model to derive improved kinetic parameters for the pyrolysis and oxidation of chalcopyrite. The reaction shaft model includes the effects of turbulent fluid mechanics, entrained flow mixing, turbulent particle dispersion, heterogeneous particle reactions, radiative and convective heat transfer, and' surface and bath deposition rates. Particle reaction and composition characteristics are predicted as a function of particle trajectory and deposition and are used to aid in evaluating shaft performance.

Jan 1, 1999