Search Documents

By Dao Su, Kelang Mu, Yufeng Guo, Jinghua Zeng, Tao Jiang

"The influence of high pressure roller grinding (HPRG) on sintering of iron concentrate fines was investigated. Results of mini-sintering tests showed that assimilation temperature of iron concentrate fines decreased from 1230 ? to 1220 ? and assimilation time was shortened from 10 min to 5 min when the iron concentrate fines was pretreated by HPRG. Sinter pot tests showed that the yield of sinter increased from 60.33% to 72.92% , tumble index increased from 44.35% to 46.66%. The investigation indicated that, after being pretreated by HPRG, iron concentrate fines are improved in ballability and the fraction of fine particles increased, resulting in the improvement of granulation property and reactiveness in solid state reaction. As a result, sintering of iron concentrate fines were strengthened.IntroductionWith the rapid development of iron and steel industry and the decrease of high-grade ores, the imports of iron ore are increasing continually. It is of immensely strategic importance for development of iron and steel industry and energy security in our country to make good use of iron concentrate fine which is low price, high grade and has a refractory sintering property. When iron concentrate fine is used in sintering, granulation property of sinter mixture and permeability of sinter bed get poor. As a result, yield and quality of sinter fall down. Many researches show that, when HPRG is used in pelletization, quality of pellets is improved dramatically. Meanwhile, HPRG has a low energy consume, a large handing capacity and it is benefit for environment protect. At this theme, strengthening of sintering of iron concentrate fine pretreated by HPRG was investigated in this paper."

Jan 1, 2012

By Derek J. Fray

"In order to extend the application of fused salts in\the electrowinning and electrorefining of metals, it is necessary to maximise the current density, minimise the voltage drop and greatly increase the area of electrode surface so as to compete with the space-time yield of pyrometallurgical reactions. The various designs of electrowinning cell are reviewed and it is shown that by the application of a modest centrifugal field it is possible to reduce the anode to cathode interelectrode spacing to 4 mm whilst still maintaining a current efficiency of 85-90%.The thermodynamic potential for electrorefining is far less than for electrowinning yet fused salt electrorefining is only applied in limited cases. The reasons for this are discussed and the important design parameters evaluated. It is concluded that by using packed bed electrodes, separated by a diaphragm, the possibility of electrorefining with very low energy consumption can be achieved. Carbothermically-produced metals are always cheaper than those produced by electrolysis but suffer from the disadvantage of low purity. It is proposed that fused salt electrorefining may offer an energy efficient way of upgrading the metal. IntroductionThe majority of metals can be deposited from fused salts (1,2) but as commercial production is restricted to the more reactive elements, it is worthwhile considering the advantages and disadvantages of fused salt electrolysis as' compared to smelting and aqueous electrolysis. The advantages over aqueous extraction are as follows:1) the much higher conductivities and diffusivities result in much lower IR losses and higher current densities can be achieved at modest voltages;2) the elevated temperatures of operation result in larger exchange currents which give rapid kinetics and lower activation polarisation for the electrode reactions;3) the absence of water as a solvent means that it is not necessary to consider the evolution of hydrogen as a competing cathodic reaction. Furthermore, alkali halide salts, often used as solvents in fused salt electrolytes, have high deposition potentials;4) molten salts generally are mutually soluble and, therefore, concentration polarisation effects are minimised."

Jan 1, 1988

By Juan H. Rojas C.

The Chuquicamata mining and metallurgical complex is the main Division belonging to Corporation Nacional del Cobre de Chile (CODELCO-CHILE) and it accounts for 50% of the 1.4 Mt of fine copper output of the Corporation. It has been producing copper since 1915. The paper refers to the challenges that Chuquicamata has to solve in the near future. These challenges are: the increasing operation costs associated to a 800 m depth pit with low prices in an overstocked copper market; the increasing people's sensitivity to environmental preservation; and, the transformation needed for achieving high levels of organizational effectiveness. According to Corporate policy, Chuquicamata is making efforts to switch from a management style focused on supply to a management style focused on demand side of the industry. In this direction is tempting to establish strategic alliances to develop both new copper products and uses, to rise the metal demand. In more than 80 years of operation, Chuquicamata had exploited just one third of its geological resources. The exploitation of the remaining two third is a huge engineering challenge, taking into account the depth of the deposit, the impurities content, the decreasing ore grades and the transportation distances for waste dumping. All those factors are relevant in the economical process of transforming geological resources into ore reserves. Chuquicamata has other limitations. First, a 20,000 people town just aside the pit that limits the mining rates because of dust generation; second the scarceness of water in the desert area where Chuquicamata deposit is located; and, finally, the new tailing pond is a problem which solution will demand huge engineering efforts and investments. People are the principal factor associated to a company success. In this field, Chuquicamata have been progressing, but much more efforts from people will be necessary to reduce production costs for being successful as any other price-taker within the copper industry. Chuquicamata must develop the skills of its Supervisors to transform them into leaders and entrepreneurs, who additionally have the challenge of passing on their knowledge to non-professional workers. It is an ethic commitment to assure personal and professional growth of workers, as the only sustainable way to get real and integral success.

Jan 1, 1999

By Masayuki Kudoh, Tohru Maruyama, Yohichi. Ito

When hypo-peritectic carbon steel is quenched during unidirectional solidification, the region of fine columnar grain is observed. It is classified into two coexisting phases. One is coexisting phases of liquid, delta and gamma in the upper part of the region, and the other is coexisting phases of delta and gamma in the lower part of the region. To form the coexisting part of the three phases means that solidification in this experiment proceeds in non-equilibrium state. The size of the narrow side of one fine columnar grain coincides with the arm spacing of a primary dendrite and this result is the same as the hyper-peritectic carbon steel. However, the boundary of the fine grain in the hypo-peritectic carbon steel is formed in different location from that of the hyper-peritectic carbon steel. The former is formed in the skeleton of the dendrite, while the latter is formed in the interspacing of the dendrite. The region of the fine grain changes suddenly to that of the coarse grain when the delta phase in the coexisting part of two phases disappears completely. Therefore, the delta phase in the hypo-peritectic carbon steel might prevent the growth of gamma grain. In order to recognize it, ferrite formers such as Mo, V and Ni are added in the sample. Then, the longitudinal length of the fine columnar grain extends in the sequence of the no addition, Mo, V and Nb.

Jan 1, 2000

By J. L. Liow

Studies have been carried out on the causes and effects of slopping in an annular cylindrical geometry such as the top submerged combustion reactor. Properties of standing waves formed such as the wave profile, period, pressure distribution and velocity have been derived analytically. The wear profile due to wave erosion was calculated based on the assumption of linear motion and that the wear is a dissolution process. The use of the j, factor showed that the wear was proportional to the square root of the wave velocity at any point. Using the dimensions of the lsasmelt reactor given by Errington et al. (1987)[11, the wear profile due to wave erosion was calculated using the analytical solution. The wear profile calculated was shown to have a maximum just below the initial bath surface. The wear was found to be concentrated in the region where the first asymmetric standing wave was most active. The results showed that the refractory near the bath surface will be affected by wave erosion, more so than any other parts of the reactor. The contribution of wave erosion on wear must be accounted for in assessing the total refractory wear of a vessel in which slopping exists.

Jan 1, 1991

By Dale W. Collins

The disposal of arsenic from copper operations possess various health, environmental and processing problems. There are basically two areas of concern. The first being the disposal or treatment of smelter flue dusts and the second the removal of arsenic from refinery electrolytes. A number of treatment options have been proposed including the addition of soluble arsenic wastes to copper heap and dump leaching solutions. This approach will allow arsenic to be reintroduced to the ore via Solvent Extraction (SX) raffinate associated with hydrometallurgical operations. Knowledge of the attenuation behavior and mechanism during leaching is important in determining the long term stability of arsenic and the success of this approach. Parameters, such as uptake capacity, pH, particle size and solution chemistry have been investigated. Arsenic attenuation has been examined using column leaching with experiments employing both continuous flow and pulsed additions of As(V). In the initial stages of leaching, the attenuation of arsenic appears to depend on the pH and iron concentration in the effluent. Arsenic stability in the copper oxide ore has been examined with rinses of progressively lower pH.

Jan 1, 1994

By K. Walanabe

Kosaka Smelter & Refinery has a history of more than a century as a metallurgical department belonging to Kosaka mine. It has treated for a long time the "Black Ore" or the complicated concentrates dressed from it. The "Black Ore" is composed of black sulfides. It contains not only valuable metals such as gold, silver, copper, lead and zinc but also some impurities like arsenic, antimony and bismuth. With the development of Kosaka's floatation technology, five kinds of concentrates (copper, zinc, lead, pyrite and barite) have been separated from the "Black Ore" but the separation was not complete and each concentrate contained some unfavorable impurities. In 1980s the highly appreciated yen and the drop of the metals prices forced many domestic mines to close their operations. Since then Kosaka Smelter has changed its way of operation to a custom smelter. Now more than 95% of copper concentrates are imported to take advantage of this technology of "Black Ore" treatment. It mainly treats the raw materials that contain high gold and silver like the "Black Ore". Recently, Kosaka has been working on the recycling of the metals from the printed circuit board scraps and sludge which contain some precious metals. The volume of the recycled metal is continuously increasing.

Jan 1, 2003

By José Carlos Abreu

This work presents a kinetics study covering the effects of temperature over the reduction rates of a carbon composite briquette, aiming its use as burden in some of the new alternate ironmaking technologies, such as the Tecnored process. It is reported that increases in the temperature increases the reaction rate. Additionally, the morphology of the iron phase generated during the reduction of these briquettes is presented. It was possible to verify that three types of iron morphology occurred during the process: an external, dense and continuous iron layer, the presence of iron globules at the center of the briquettes and whiskers at the briquette's core. The measurement of the carbon content on the globules and the external iron layer is also presented.

Jan 1, 2003

By Guozhu Ye

"One of the most essential problems associated with the treatment of EAF dust is its high content of halogens. For most thermal processes for zinc recovery, such as the plasma processes with a zinc condenser, the halides in the gas stream will form a dross phase that results in a low zinc yield. For those with zinc oxide as main product, such as Waelz oxides, the high halogen content in the product implies a great degradation of the product quality and the product can only be sold at a low price. Further processing of zinc oxide with high halogen content either by pyrometallurgical or hydrometallurgical processes will also result in process problems.This paper will review the pre- and post-treatment alternatives for halogen removal based on the comprehensive characterization work that has been carried out at MEFOS and the preliminary experimental results.The experimental results show that chlorine and fluorine content could be reduced to 450 ppm and 50 ppm respectively by selective sulfation, and to about 200 ppm by soda leaching. Selective sulfation of zinc oxide in the EAF dust will also be discussed."

Jan 1, 2000

By C. J. Malek

The CONTOP® smelting cyclone technology is a large-scale and time-proven method which in combination with other technologies (grinding, drying, pyrolysis, etc.) provides for a cost- efficient and ecological disposal of a wide range of waste materials from industry and households. In this report the basic principle of smelting cyclone technology will be explained first. Subsequently, the paper will discuss substantial concepts for the recovery of various remainders.

Jan 1, 1996

By C. D. Chapman

Current regulations regarding the landfill disposal of asbestos containing wastes are inadequate to ensure there are no ground water or airborne emissions. Accordingly, there is growing recognition that asbestos wastes can only be safely disposed of by using techniques that destroy the hazardous fibres. An innovative high-temperature plasma arc technology (The MAGRAM Process) is being developed for the recovery of magnesium metal from asbestos together with supplementary magnesia containing feedstock. The furnace will operate in. open bath mode with aluminium and/or ferrosilicon being employed as reductant. An important advantage of the process is that magnesium vapour within the furnace will be generated close to atmospheric pressure rather than at reduced pressure under which existing processes operate. Thermodynamic modelling work has been undertaken to define the range of slag composition and furnace temperature under which magnesium production at atmospheric pressure is feasible. The effect of slag chemistry, reductant addition, and temperature on product quality and yield have also been investigated and key aspects have been tested on bench scale. A 300 kW pilot plasma furnace unit has been employed for the treatment of calcined asbestos wastes. Aspects of design and operation of the unit are detailed. Acknowledgement: This work is substantially financially supported by the European Communities under the Industrial and Materials Technologies (Brite EuRam H) Research and Development programme.

Jan 1, 1995

By Karl A. Gschneidner

The magnetocaloric effect has been known for 120 years and has been utilized for cooling about 70 years. But in the last four years significant advances have been made to show that magnetic refrigeration is a viable and competitive cooling technology. Most of the work has focused on reciprocating devices, but rotary apparati are being developed. To date the magnetocaloric properties have been characterized for more than 200 materials. The magnetocaloric effect behaviors have been classified into three types of behaviors. The most common one is found in magnetic materials which exhibit a second order magnetic phase transition. Magnetic materials which exhibit a first order magnetic phase transition account for the second group of materials. Materials which exhibit multi-magnetic phase transitions make up the third group. The best candidate materials for magnetic cooling over the range from -4 to -1 350 K are also presented.

Jan 1, 2002

By SIMON TIMBILLAH

The chalcopyrite-molybdenite (Cu-Mo) flotation industry is increasingly turning to organic depressants as suitable replacements for inorganic reagents, such as NaHS, due to environmental and safety concerns as well as high consumption rates of the inorganic reagents. This presents an opportunity for improvements or design and synthesis of alternative reagents. Disodium carboxymethyl trithiocarbonate (Orfom® D8) depressant is an organic depressant with a carboxylate group on one end and a trithiocarbonate group at the other end. Fundamental results are shown regarding the interaction of the Orfom® D8 depressant in the bulk flotation of a Cu-Mo concentrate from an operating North American mine. Cyclic Voltammetry on pure copper and Fourier Transform Infrared Spectroscopy (FT-IR) and X-ray Photoelectron Spectroscopy (XPS) measurements on pure chalcopyrite with Orfom® D8 depressant treatment are also reported. Through such characterization techniques a potential adsorption mechanism of Orfom® D8 on the mineral surface was identified and its depressant characteristics in the Cu-Mo flotation systems explained.

By A. Dadgar

Extraction of gold and silver from two refractory concentrates using cyanide and bromine reagents was reported at the 12th International Precious Metal Conference (1). The objective of this paper is to present the gold extraction, recovery, and economics for two refractory concentrates using cyanide and bromine reagents. Gold extractions for cyanide leaching (24- 48 hours) and bromine leaching (6 hours) were the same and ranged from 94% to 96%. Gold recoveries from bromine pregnant solutions using carbon adsorption, ion exchange, solvent extraction, and zinc and aluminum precipitation methods, were better than 99.9%. A preliminary economic analysis indicates that chemical costs? for cyanidation and bromine process are $9.50 and $10.50, respectively per ton of calcine processed.

Jan 1, 1989

By Rodney L. Williamson

Vacuum arc remelting (V AR) is an industrial metallurgical process widely used throughout the specialty metals industry to cast large alloy ingots. Part of the V AR control problem consists of adjusting arc current to control electrode melt rate which also depends on the electrode temperature distribution. Because the temperature distribution responds very slowly (1-4 hours depending on size and material) to changes in melt power, the melt rate response is history dependent and highly nonlinear. The situation is complicated further because measurement of the electrode temperature distribution is not practical. To solve the problem of accurate, responsive melt rate control. a low order electrode melting model has been developed and incorporated into a V AR process controller. Data from laboratory and industrial tests show that the goal of responsive, accurate melt rate control has been achieved, even when melting under highly dynamic process conditions. Keywords: Vacuum Arc Remelting. Model-Based Control

Jan 1, 2003

A novel pressure leaching process for platinum group metal (PGM) feedstocks is described. The process is particularly well suited for treatment of ores or concentrates that are too low grade for economic processing by the conventional smelting/leaching process. Operating conditions have been identified under which gold, the PGM's and the base metals dissolve simultaneously in a pressure leaching autoclave. The product of this leaching process can then be treated by one of several flowsheets, of which the preferred will likely involve solid/liquid separation, followed by precipitation (or adsorption on activated carbon) of gold and the PGM's, followed by copper solvent extraction/electrowinning. Depending on the concentrations of nickel and cobalt, the copper raffinate would either be partially recycled to the autoclave to allow NilCo concentrations to build up, or it would proceed directly to a Ni/Co refinery. This paper deals with the pressure leaching process and the recovery of gold and the PGM's from the pressure leach product.

Jan 1, 2000

By Murali Thirukkonda, Rahul Shah, Srinivas Tangrila, Shankar Rachakonda, Jan Kajuch, Arthur Gurson

"High-temperature superconductors have potential for a variety of applications such as power generators, superconducting magnets for mine sweepers or ship propulsion motors, and magnetic levitation transportation systems. Interest in the use of superconducting wires and tapes increased dramatically after the discovery of high-critical-temperature (high-Tc) oxide superconducting compounds, which offer operating temperatures above that of liquid nitrogen. Several techniques have been proposed to produce commercially viable high-Tc oxide based superconducting wires. One of the promising methods involves multi-pass powder-in-tube (PIT) wire drawing followed by rolling and heat treatment. This work focuses on the development of a numerical model to simulate the PIT drawing process for fabrication of long lengths of silver sheathed Bi-2212 superconducting wires. The finite element based model was used to predict densification of the oxide powder, wire drawing forces, and silver sheath thickness during drawing. A cap-type pressure dependent constitutive equation was implemented in the model to simulate the powder behavior. The model incorporated experimentally obtained material data for the silver and powder. Results indicate that powder densification is increased by decreasing the initial silver thickness and increasing the silver strength. Data from wire drawing experiments were used to verify model predictions. IntroductionSuperconducting wires and tapes can be used to carry large dc currents with no measurable loss due to resistivity. When used in superconducting magnets for power generators, motors, levitation devices, magnetic detectors, or energy storage devices, they could potentially result in significantly reduced energy losses. In the past, most prototypes were tested in liquid helium at 4.2K [1]. However, the necessity to provide liquid-helium cooling systems proved to be a serious limitation in commercialization. In 1986 high-critical-temperature (high-Tc) oxide superconductors were discovered [2], which could allow for higher operating temperatures above liquid nitrogen (77 K). Since then, both academia and industry have concentrated their efforts on the development of high-Tc oxide superconducting wires, tapes and coils. As yet, large scale fabrication of long lengths of these wires with the required current carrying capacity and mechanical properties remains an enormous challenge."

Jan 1, 1994

Novel techniques were developed to obtain samples from and make measurements in the shaft of the flash furnace at the Kalgoorlie Nickel Smelter. The data obtained was used to validate mathematical models of the burners and the reaction shaft. Particle, gas and wall temperatures were measured along with the oxygen potential of the molten particles. Collected particles were characterised by sizing, chemical analysis and optical microscopy. The region of the shaft immediately beneath the burner where the rate of change was most rapid received special attention.

Jan 1, 1993

By Sang Han Son

The vapor pressures of FeCI2 and ZnC12 in the FeCl2-ZnCl2 system were measured by the transpiration method at 873K and 917K. The vapor pressure data were interpreted to indicate the formation of complex ions in the FeCl2-ZnCl2 melts. It is presumed that the complex molecule FeZnCl4 as well as FeCI2 and ZnCI2 exists in the vapors in equilibrium with molten FeCl2-ZnCl2 mixtures. The activities in the FeCl2-ZnCI2 system are shown a negative deviation from Raoult's law. These results suggest the formation of complex ions such as ZnCl42- in molten FeCI2-ZnCI2 mixtures.

Jan 1, 2003

By Eric J. Grimsey

Steady state Excel models for a copper flash smelter and an iron blast furnace are used to enhance the teaching of pyrometallurgical smelting principles within a fourth year level process engineering unit delivered at the Western Australian School of Mines. A lecture/workshop approach has been adopted in which student teams undertake process simulation assignments that illustrate the multifaceted responses of process outputs to variation of inputs, the objectives being to reinforce their understanding of smelting principles. The approach has proven to be popular with students, as evidenced by the consistently high ratings the unit has received through student feedback. This paper provides an overview of the teaching approach and process models used.

Jan 1, 2014