Search Documents

By Jewel A. G. Gomes

Electrocoagulation (EC) has been performed with Al-Fe electrode system with changing polarity for the removal of arsenic from water. The removal process has been studied using ICP-AES and Anodic Stripping Voltammetry with a wide range of arsenic concentration (1-1000 ppm) at various pH (4-10) and residence times (1-60 min). Electrochemically generated by-products have been analyzed using XRD, FTIR, XPS, SEM/EDS and Mössbauer Spectroscopy. Results revealed expected crystalline iron oxides (magnetite (Fe3O4), lepidocrocite (FeO(OH)), iron oxide (FeO)) and aluminum oxides (bayerite (Al(OH)3), diaspore (AlO(OH)), mansfieldite (AlAsO4?2(H2O)), as well as some interaction between the phases. The amorphous or ultra-fine particular phase was also found in the floc. The substitution of Fe3+ ions by Al3+ ions in the solid surface has been observed, indicating an alternative removal mechanism of arsenic in these metal hydroxides and oxyhydroxides by providing larger surface area for arsenic adsorption via retarding the crystalline formation of iron oxides.

Jan 1, 2006

By Liguang Zhu, Yihua Han, Qingjun Zhang, Xiaoyan Wu, Pengcheng Xiao

The evolution of chemical composition, size, proportion, and morphology of the Al-Ti-Mg-O inclusions during the steelmaking process of Interstitial Free (IF) steel from the RH to the Continuous Casting (CC) slab were investigated by means of Auto-SEM. Results showed that many of Al2O3 and MgO-Al2O3 type inclusions are modified by TiOx, while most of their shapes are irregular due to the high melting temperature. The composition evolutions and melting characteristics of Al-Ti-Mg-O inclusions under different contents of [Al], [Ti] and [Mg] were estimated by using thermodynamic software Factsage 7.0. Results showed that estimated results are in good agreement with the analysis results of industrial samples. Both the Ti alloying and spontaneous enrichment would make a high Ti concentration environment that was in favor of the TiOx existence. Moreover, more TiOx component can modify MgO-Al2O3 spine inclusion into inclusions with a lower melting temperature.

Mar 1, 2018

By Animesh Jha

"Fine ceramic powders (<500 nm) exhibit exceptional physical and mechanical properties in engineered structural ceramics. The production of fine powders, in particular the non-oxide ceramics, via a cheaper route than the organic solvent route has been rather elusive. This paper examines the physical chemistry of sub-oxide vapour-phase reduction reaction for the nucleation of non-oxide ceramic phase. Well known vapour species eg SiO and BO in the production of technical ceramic powders (SiC, BN) are particularly discussed for understanding the nucleation process of SiC and BN ceramic phases respectively. The regimes of partial pressures and temperatures are particularly 'identified. The calculated nucleation rate as a function of the temperature is compared with the experimental results on powder morphology. The production of amorphous and nanocrystalline h-BN powders is discussed in the context of substrate structure and thermodynamic parameters.IntroductionThe physical and mechanical properties of ceramic components are strongly dependent on the powder particle size and morphology used for their fabrication. For example the strength (Os) of the structural ceramic components increases with decreasing average grain-size (d) in accordance with the Hall-Petch relationship: Os = 0""0 + k/(d)1/2. Here k is an empirical constant which can be established from the graphical relationship. However as the particle size approaches submicrometer-size range, the dependence of strength on the particle size becomes more complex [1]. The design of ceramic components based on nanometer-size particles have recently become an important field which can offer ceramic materials with properties comparable to their metal counterparts. Several materials based on these concepts have been developed and reported by Niihara [2]. For example, the Al2O 3-SiC nanocomposite, having average B-SiC grain size 0.3-2um with intragranular SiC particulates of 5-10 nm has unusually high strengths (1100 MN/m2) at low and elevated temperatures combined with enhanced fracture toughness (> 4 MN-ml.5) which is an unusual combination in structural ceramics. Besides mechanical properties, as the particle size of ceramic powders approaches the nanometer-size range, the charge transport properties also improve by many times. The effect of particle size on the electrical conductivity of Si3N4-TiN composites has been well documented [3.4]. The size of ceramic particulates without doubt plays a pivotal role in determining the properties of ceramic components."

Jan 1, 1996

By Daoxin Wu

Originated from(C4H9O)4Ti, nano--rutile TiO2 was synthesized by low temperature hydrolysis process in this paper. After being prepared by decomposing ammonium tungstate and covering on the surface of TiO2, TiO2/WO3 were characterized by means of X-ray diffraction(XRD), UV--vis difuse reflectance(DRS), fluorescence spectrum (FS). Results showed that with the increase of the supported concentration of WO3, the reflectance of DRS and the fluorescence spectrum intensity of TiO2/WO3 decreased accordingly, which indicated the powder?s increase in light absorbance and the decrease in luminescence respectively; with the increase of calcined temperature, the reflectance of DRS increased.

Jan 1, 2009

By Forsén. O.

In this ?paper practical solidification of anodes containing nickel, arsenic, antimony and bismuth is compared with the equilibrium? diagrams and kinetic ?factors. In order to clarify the distribution of the impurity elements in the anode the structures were studied after the solidification and also after the electrolysis of anodes. This examination was carried out with optical microscope, scanning electron microscope and electrochemical measurements. All the nickel is remaining metallic in the copper matrix during the solidification and therefore nickel is dissolved in the electrolysis at all oxygen contents, when the nickel content is 0.25 wt-% or less in the anode. The practical .solidification mechanism of the anodes, when the nickel content exceeds 0.25 wt-%, proceeds by the crystallization of nickel oxides. In oxygen containing copper anodes nickel oxide is verified to crystallize together with antimony in certain conditions and to form a micaceous compound (3Cu2O?4NiO?Sb2O5), which may build up a very harmful floating slime in the electrolyte. Arsenic is strongly enriched along the phase boundaries in oxygen free copper anodes. An intermetallic compound Cu3As is formed when the amount of arsenic in the anode. exceeds 0.7 wt-%. This compound is more noble than the copper matrix. This means &apos;that a selective dissolution of copper-arsenic compounds takes place. The copper matrix dissolves more strongly than the grain boundaries. The solidification structures of oxygen free bismuth containing copper anodes show clearly the influence of bismuth. Thin bismuth films which are less .noble than the metallic copper matrix, are formed during the solid1ficatton process. As a result of this the?grain boundaries are dissolved faster than the copper matrix.

Jan 1, 1987

By Jae R. Lee

Keywords: Self-propagating high temperature synthesis, AlN, Powder synthesis The particle size and shape effects of starting raw powders on the synthesis of aluminum nitride by self-propagating high temperature technique under high nitrogen pressure were investigated with various AlN diluents and Al reactants. It was found that the structure of beds of the starting raw particles largely affected the pore channels for nitrogen gas infiltration as well as the passages for combustion propagation before and during the reaction, resulting in the morphology and purity changes of the synthesized products. The AlN product of purity over 98% with about 30 microns was obtained.

Jan 1, 2005

By Mitsutaka Hino

The contents of gangue minerals, such as A1203, P205, crystalline water and so forth in the iron ore imported to Japan tend to increase year by year, Though the increments of such gangue contents are approximately 0.1-0.2 mass%, some problems for the blast furnace operation in ironmaking process have already been reported, In order to clarify the mechanism of harmful effect caused by the small increment of gangue minerals, mainly A1203, on the blast furnace operation, the dripping behavior of FetO-CaO-SiO2-AI2O3-MgO slag from the iron funnel, which simulated the micro-porosity in sinter ore, has been observed with the wide range of basicity, Al2O3, FetO and Mgo contents. The effect of MgO on the dripping behavior of slag has been summarized in this paper, It was found that the addition of 2mass% MgO resulted in large increase of hold-up on the most of the conditions. When FetO content was less than 20mass% and the basicity was lower than 0.8, MgO lowered the hold-up even if the slag contained 10mass% Al2O3. Every slag hold-up showed the minimum at the basicity of less than unity on the conditions of constant FetO and A1203 contents. This trend became remarkable when the slag contained 2 mass% MgO.

Jan 1, 2003

By Achilles J. B. Dutra, Carlos M. Juarez

"The use of thiourea as a gold leaching reagent has been extensively studied by many researchers, and it has proved to be promising for some cases as refractory ores. Otherwise, the recovery of gold from these solutions did not receive so much attention. In this paper the electrowinning of gold in acidic thiourea solutions was studied by voltarnmetry and chronopotentiometry. An adsorption step was detected prior to Au(I) reduction and the diffusion coefficients at 25°C for Au-TU complex and FD were found to be 1.00 x 10.5 cm2 S-I and 1.98 x 10-5 cm2 S-I respectively. At -0.350 V (SCE) a passivation probably due to TU adsorption was observed. For higher overpotentials hydrogen evolution was the main reaction.IntroductionThe use of acidic thiourea solutions for the extraction of gold and silver has shown to be a promising alternative to the traditional process of cyanidation, specially for certain refractory ores (1-3) and electronic scrap (4). In some cases, the industrial scale was reached (1,5). The thiourea leaching of precious metals presents advantages over cyanidation, as faster kinetics, lower toxicity and lower sensibility to base metals; however the costs due to high thiourea consumption impairs its use.The majority of the publications on thiourea processing of gold is on leaching. Many are review papers (5-7). Recently, the adsorption and desorption of the gold-thiourea complex on activated carbon and ion exchange resins have been studied (8-11).Little research has been done on the electrowinning of gold from acidic thiourea solutions, most of it has been carried on the seventies and beginning of the eighties in the former USSR (12-17) and concerned the eletrolytic extraction of gold in tridimensional cathode cells.The present paper concerns the cathodic behavior of the gold-thiourea complex in the presence of formamidine disulfide in order to provide information on the electrowinning of gold from solutions obtained directly from leaching or from an elution process."

Jan 1, 1997

By Muammer Kaya, Sait Kursunoglu

"The aim of this study was to investigate the effectiveness of ascorbic (C6H8O6) / oxalic (C2H2O4) acid as a reductant for the simultaneous recovery of zinc and manganese from a spent and mixed zinc-carbon and alkaline battery powder in sulphuric acid leaching. The effects of sulfuric acid concentration, ascorbic/oxalic acid dosages, reaction temperature and leaching time on the zinc and manganese dissolutions were investigated according to 2k full factorial experimental design; then, a simple optimization study was carried out for the best reductant. The optimum reductive acid leaching conditions were determined at 3 hours leaching time, 70°C leaching temperature, 0.5M sulfuric acid concentration, 13 g/L ascorbic acid dosage, 1/20 g/mL solid/liquid ratio and 200 rpm stirring speed. Under these conditions, the dissolution efficiencies were 99.9% for Zn and 99.3% for Mn. When our results were compared with the previous results, our findings were better than previous studies.In addition, the manganese dissolution kinetics was undertaken, and the activation energy was found to be 7.04 kJ/mol. Selective precipitations of Zn and Mn from acid solutions were carried out using NaOH and KOH. Using 3M NaOH as precipitating agent at room temperature and at pH 8; 95.4% of Zn and at pH 10; 93.7% of Mn were precipitated from the leaching solution. Under the same conditions, using 3 M KOH at pH 8; 91.6% of Zn and at pH 10, 96.4% of Mn were precipitated. Based on the experimental results obtained, an appropriate flow sheet was proposed to recover zinc and manganese."

Jan 1, 2012

By Hong Liang-shi

Olivine lithium iron phosphate (LiFePO4) is considered as one of the most promising materials for lithium-ion secondary batteries because of its high theoretical capacity, low cost, good safety, benign environment and good cycle performance. In this paper, carbon-free and/or carbon-coated olivine lithium iron phosphate composite ultrafine powders were successfully synthesized from aqueous precursor solutions of (NH4)2Fe(SO4)2?6H2O, H3PO4 and LiOH?H2O by co-precipitation method. The obtained LiFePO4 or LiFePO4/C powders were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Their electrochemical performance was investigated in terms of cycling behavior. As confirmed by X-ray diffraction and scanning electron microscope, the material obtained by co-precipitation within the temperature range of 60ºC to 100ºC and then followed by moderate heat treatment are a single-phase olivine LiFePO4with the particle size of about 300nm. An improved carbon-coated olivine LiFePO4/C material was prepared by adding conductive carbon materials, such as glucose, activated carbon and acetylene black, into the precursor. The carbon dispersed in the materials increases the electronic conductivity of LiFePO4/C composite, and consequently, leads to high rechargeable capacity of the material. The carbon-coated material with carbon amount of 7.64%wt obtained from glucose has the first discharge capacity of 150.3mAh/g at the rate of 0.1C and 129.3mAh/g at the rate of 1.0C, respectively. After cycled for 50 times, the capacity retention rate is 95.13% at the rate of 1.0C in the voltage range of 2.5 to 4.3 V vs. Li/Li+.

Jan 1, 2006

By Florian Kongoli

New operating conditions and process parameters are often necessary in today&apos;s industrial practice of non-ferrous smelting and converting in order to accommodate various new chemical compositions of mineral charges and environmental requirements or to conceive new and more efficient industrial technologies. An important parameter in non-ferrous smelting and converting is the liquidus surface of multicomponent slags. This surface is affected by multiple factors such as temperature, gaseous potentials, the content of each component in the slag, etc., and cannot be quantified by the existing ternary liquidus diagrams. In this work a new type of representation of the liquidus surface of multi component systems has been presented by means of a thermodynamic model. This representation waives the need of the multidimensional representation of multi component systems and yields practical two-dimensional diagrams, which can be easily used in the industrial practice.

Jan 1, 2000

By Hai-Peng Guo, Lu Jiang, Xiao-Man Yan, Bing Xie, Hong-Yi Li

Traditional, calcium compounds cannot be used in vanadium extraction processing due to the limitation of sodium roasting technology, which results in unsatisfied dephosphorization for vanadium-containing hot metal in converter and thus increasing the dephosphorization burden for subsequent steelmaking. The calcium roasting technology is an alternative for vanadium extraction and allows adding lime into vanadium slag in converter. In the present study, vanadium was leached by soda from roasted vanadium slag with high calcium content. Effects of roasting temperature and time, leaching temperature, Na2CO3 concentration andliquid to solid ratio on vanadium leaching rate were studied. The results show that 94% of vanadium was extracted by roasting the vanadium slag at 950℃ for 2.5h and then leaching in 160g/L Na2CO3 liquid at 95℃ for 1h with liquid to solid ratio of 10:1 ml/g. Impurities of Si and P reacted with calcium and formed insoluble Ca2SiO4 and Ca3(PO4)2 respectively.

Jan 1, 2015

By Teruhisa HORITA

The durability of SOFCs is one of the critical issues to realize the SOFC systems. In order to improve the durability, a precise degradation mechanism should be clarified at the different functional ceramic interfaces in SOFC cells and stacks. This paper reviews the improvement of SOFC durability by the mass transport analysis especially at cathode/interlayer/electrolyte interfaces. We have made a precise analysis on the reaction of cathode with impurities. Especially at the (La,Sr)(Co,Fe)O3/CeO2/ZrO2 interfaces, a significant amount of SrCrO4 and SrSO4 were observed at the (La,Sr)(Co,Fe)O3 surface as well as inside the (La,Sr)(Co,Fe)O3 cathode, which suggested some process occurred for both poisoning. Possible degradation mechanisms were proposed based on the observation data.

Jan 1, 2016

By Lu Lin, Yanping Bao, Xiang Li, Linzhu Wang, Xiaobai Yan

The results showed the microinclusions were mainly Al2O3 and sulfide inclusions from tapping to the beginning of LF refining. Al2O3 inclusions were modificated into calcium aluminates after calcium treatment. Lots of spherical calcium aluminates composite inclusions containing MgO, TiO2 and MnS were found after soft blowing and during tundish metallurgy and left in the slab which caused the defects of beam plates. Pure Al2O3 inclusions were observed again after soft blowing 8min. Average sulfur content in inclusions decreased because of the high desulfurization ability of refining slag. Average Ca/Al ratio value in inclusions increased during LF refinging because of the reduction of CaO in slag by carbon and it increased obviously during the process of soft blowing 8min because of the dissolusion of calcium wire.

Jan 1, 2015

By Bora Derin, Onuralp Yucel, M. Seref Sonmez, Murat Alkan

"Latest stage in the production of boron carbide by metallothermic methods using magnesium was the leaching process. Boron carbide particles obtained by self-propagating high temperature synthesis contained several impurities such as magnesium oxide and magnesium borates after the metallothermic reactions. Removal of such contaminates by hydrometallurgical methods required to produce high purity boron carbide. Leaching by concentrated hydrochloric acid solutions resulted in the production of pure boron carbide together with high magnesium and boron containing solutions. Removal of such ions from the spent liquor was the necessity to have dischargeable solution. In this study, precipitation of magnesium and boron compounds from relevant chloride containing spent liquors and the production of saleable products was aimed. The effects of chemical reagents, pH of the solution on the precipitation efficiency of magnesium and boron compounds were investigated in the study. Chemical analysis and the characterisationof solid phases by using x-ray diffraction analysis were the latest stage.Introduction A variety of advanced ceramics, inter-metallic, organic and inorganic compounds, oxygen free single crystals, and polymers can be synthesized by using different SHS techniques [1, 2, 3]. In the SHS process, after initiation, reaction becomes self-sustaining and propagates in the reactant mixture. A high amount of heat which is generated during the process accelerates the reaction rate and thus it makes the process highly productive and economically feasible for different production scales. After the SHS process obtained powder mixture needs to reacted with acidic solutions to purify the product. In this case B2O3 was reacted together with C and Mg to synthesis fine B4C powder resulted in the production of MgO as well according to the Eq. 1 and then MgO was removed from the mixture by leaching with the concentrated HCl solution as shown in Eq. 2, respectively [4, 5]."

Jan 1, 2008

By P. Umadevi

In the light of the discovery of the new super-conducting YBa2Cu3O7-x (YBCO), reactions in the Y2O3¬CuO-BaO system at 1300°C was investigated. The search was for any new phase that may be formed in the system at 1300°C (only 950°C reactions are known so far). 35 mixtures of different compositions were prepared and heated at 1300°C. No new phase was obtained. It was found that YBCO is decomposed at this temperature and Y2O3 and BaCO3 are the major components in the solid obtained after firing in air. However, on cooling the melt slowly and annealing at 950°C YBCO reforms. Such reactions on cooling might have implications on processing of the superconductor YBCO for practical applications as well as on its crystal growth by flux method.

Jan 1, 1989

By David Norval

Ni, Co, Cu and Pt, mattes are common materials that require granulating and milling of the resultant granules for further processing. This route is acceptable if the material is brittle (friable) which is a property associated with the higher sulphur mattes. For lower sulphur levels, where the matte is less amenable to milling, the costs of the milling increases. This paper will compare water granulation with certain dry granulation processes and the downstream processes required for Hydrometallurgy. It will further introduce and expand on atomisation which offers a further safety benefit in the control of the metal flow into the &apos;wet zone&apos; with the use of a tundish flow control also reducing the conversion from the matte to powder in one fairly straightforward operation.

Jan 1, 2006

By Baozhong Ma, Chengyan Wang, Yongqiang Chen, Peng Xing

This paper introduces an oxygen-enriched flash smelting (OFS) process for lead smelting. Compared with the bath smelting, OFS has many advantages, including wide adaptability, high yield, low energy consumption, little uncontrolled emission, and considerable metals recoveries. Test results showed that increasing CaO could effectively reduce lead content in the slag, and the appropriate mass ratios of FeO-to-SiO2 and CaO-to-SiO2 were 1.15 and 0.6, respectively. The testing and commissioning indicated when OFS was used to treat material containing 30% of lead, the residual lead in slag could decrease to 4–10%. Furthermore, after zinc volatilization using an ore-smelting electric furnace, contents of lead, zinc, silver, gold and copper in the final slag were below 2%, 2%, 6 g/L, 0.1 g/L and 1%, respectively. The total recoveries of lead, zinc, silver, gold, copper and sulfur were above 98, 90, 99.5, 99.5, 85 and 98%, respectively.

Mar 1, 2018

By Xueqin Li, Xuewei Lv, Yu Zhang, Wenchao He

In order to make full use of the chromium-bearing vanadium titanium magnetite with chromium, a new process of “direct reduction-electric furnace smelting separation” has been developed for recovering the iron, vanadium, titanium and chromium in recent years. In this paper, FactSage, one of the most frequently-used thermodynamic calculation software, was used to calculate the reduction degree of Fe, V and Cr with different n C/nO (mole ratio of carbon and oxygen). It was found that the suitable operating conditions of direct reduction process were n C/nO > 1.07 and T > 1473 K. In addition, the direct reduction experiment of Hongge vanadium titanium magnetite was carried out and the obtained samples after direct reduction were analyzed by XRD and chemical composition. The result shows that the metallization rate of carbon-containing pellet is nearly 90%.

Mar 1, 2018

By Hiroyuki Matsuura

The effects of P2OS or Na2O addition on the reaction rate of CO2 dissociation on the surface of FexO-base molten oxides was investigated at I 773K by isotope exchange method 1-6. The rate constant decreased with increasing P2Os content of molten oxides and the residual rate constant was observed at high P2OS content. On the other hand, the rate constant increased with increasing Na20 content for FexO-SiO2 melts, The rate constant was evaluated by the composition of oxides and the rate controlling step of CO2 dissociation was discussed.

Jan 1, 2003