Search Documents

By Krzyszof Borowiec

With the aim of determining the thermodynamic conditions for sulfation of impurity elements, in particular magnesium, in titaniferous slags the equilibrium gas composition for the sulfation reaction: MO + so2 + 1/2 02 = MS04 has been studied by an EMF technique with a solid zro2 + Cao electrolyte. Here M denotes the impurity elements: Mg, Ca and Mn, and the following _oxide systems have been studied: Ti02-MgO-Fe2 o 3 , Ti02-MnO-Mn2 o 3 , and Ti02 -CaO-Si02 , all in the . temperature range 700-1000ºc. Reproducible EMF values were obtained by adding small amounts of -Na2so4 to the oxide-sulfate mixture. From the observed results the Gibbs energy of formation of the phases Mg 2Ti04 , MgTi03 , MgTi 2o 5 , MnTi03 , CaTi03 , and CaTiSio5 , as well as the activity of MgTi05 in the solid solution with Fe2Ti05 have been calculated. The results show that, from a thermodynamic viewpoint, sulfation of these impurities in titaniferous stags i:s favorable- at around and below 800ºC.

Jan 1, 1985

By Zhitong Sui

Based on several case studies on the precipitating behavior of valuable nonferrous metal compounds (VNMC) in molten slags a green technology for the recovery of VNMC from molten slags was proposed. This technology involves three steps: (I) The selective enrichment of the dispersed VNMC into the designed mineral phase in the molten slag; (2) The selective coarsening of the designed mineral phase to a critical grain size in the molten slag; (3) The selective separation from tailing of the grown mineral phase in the solidified slag by dressing or hydrometallurgy processes. This is a clean and low cost technique and has a great capacity to deal with a large quantity of slags. The utilization of the recovered VNMC such as Titanium, Boron, Vanadium compounds was summarized as examples of application. It was confirmed by experiments that the precipitating behavior of the designed mineral phases like Perovskite(CaTiO3), Suanite(2MgO*B2O3) and Sincosite(CaOoV2O5*P2O5) in molten slags is obviously affected by operation factors such as temperature, chemical composition, heat-treatment, additives and so on. The precipitating kinetics and mechanism of the VNMC from molten slags during solidification processes were also investigated.

Jan 1, 2003

By Liangying Wen, Jian Xu, Dongdong Wang, Kaihui Ma, Yang Xu

Slags play an important role in blast furnace operation, and their com- positions are based on the CaO –SiO2–MgO–Al2O3 quaternary system. However, there is not a clear understanding of the effects of gangue on of the formation of FeO-bearing primary-slags process in blast furnace. In this work, the softening and dripping experiments under the blast furnace conditions are designed to explore the influences of CaO-/SiO 2-/MgO-/Al2O3 on the softening and melting properties of FeO respectively. The results indicate that additions of CaO or Al2O3 decrease the starting softening temperature and no dripping behaviors are found in comparison with the base case results when only FeO is used. On the contrary, the addition of SiO2 or MgO rises the starting and ending softening temperature, as well as the dripping temperature. The lowest maximum pressure drop is obtained in the case with addition of SiO2. According to XRD analysis results, the initial phase with CaO addition in the primary-slags should be CaOFe3O4 and that with SiO2, MgO, Al2O3 additions are fayalite (2FeOSiO2), magnesioferrite (MgOFeO), hercynite (FeO2Al2O3), respectively.

Mar 1, 2017

By Chuanfu Zhang, Liwei Liang, Yanxin Wu, Jinliang Wang

"According to the reaction shaft operation characteristics during the flash smelting process, 15 groups of slag samples containing high Fe3O4 were prepared by some chemical reagents, and then the slag viscosities were measured using a RTW-10 type synthetic test instrument for melt physical property by the rotating cylinder method. The effects of Fe/SiO2 ratio (mFe/mSiO2), Fe3O4 content (wFe3O4), Cu2o), MgO content (WMgO) and Cao content (wCaO) on the slag viscosity were also studied. Results show that slag viscosity is decreased with the increase of temperature, mFe/mSiO2, wCu2o, wMgO and wCao, and with the decrease of wFe3O4, under the range of slag contents: mFe/mSiO2 1.36~1.78, wFe3O4 17.83%~21.18%, wCu2o 3.51%~8.34%m wNgI 2.21%~6.57%m w/caI 6.22%~9.387% and temperature range if 1250 o/c~1450 oC. Only wFe3O4m and w/caO have great influence on the slag viscosity when temperatures as high as 1400 oC. Only wFe3O4 and wCaO have great influence on the slag viscosity when temperatures as high as 1400 oC or so. To form a freeze slag with higher viscosity inside the reaction shaft, wFe3O4 should be more than 20% and wCaO should be less then 6%.IntroductionSince its appearance in 1949, Outokumpu flash smelting technology has making continuous innovation and has become the most competitive intensified smelting technology [1], widely considered to be the standard clean smelting process [2]. At present, flash smelting technology is adopted to newly build or reconstruct most of the world's copper or nickel smelting enterprise [3]. Reaction shaft is the most important part of the flash smelting furnace. During the flash smelting process, reaction shaft must be able to withstand the following harsh conditions at the same time: 1) high temperature varying from 1400 °C to 1500 °C. 2) strong oxidative atmosphere containing 50% - 80% oxygen. 3) solid particles and melt with speed up to l00 m/s. 4) high acidic or basic slag with strong chemical corrosiveness. 5) smelting gas containing 50% - 80% SO2. 6) matte with strong dissolution."

Jan 1, 2012

By Suleyman Tekeli, Serdar Salman, Bulent Aktas

"The effect of La2O3 content up to 15 wt% on phase stability, sintering and microstructure of cubic zirconia (8YSZ) was investigated. XRD results showed that the specimens containing up to 15 wt% La2O3 were composed of only cubic structure. Also, the specimens doped up to 5 wt% La2O3 revealed no La2O3 peaks, indicating that La2O3 was completely solubilized in the cubic structure. However, when> 5 wt% La2O3 was added, the peak of La2Zr2O7 compound emerged, showing that the overdoped La2O3 was not solubilized in the 8YSZ matrix. The lattice parameter of the 8YSZ slightly decreased with the increasing La2O3 content up to 1 wt% but further increase in the La203 amount resulted in an increased lattice parameter. The comparison of grain size of the 8YSZ specimens with various La2O3 content showed that grain size slightly increased with the increasing La2O3 content up to 1 wt% but further increase in the La2O3 amount resulted in a decreased grain size.IntroductionAt atmospheric pressures, three polymorphic forms of Zr02 are stable at different temperatures i.e. monoclinic, tetragonal and cubic. A high-pressure orthorhombic form of Zr02 has also been reported[l]. The successful production of pure Zr02 bodies is not possible all the time due to the large volume expansion associated with the martensitic tetragonal-monoclinic transformation. This fact restricts the applications of zirconia, in spite of its excellent mechanical and thermal properties. However, the stabilization of the high temperature polymorphs at room temperature as stable phases is made possible by addition of suitable dopants. Fully stabilized cubic Zr02 and partially stabilized tetragonal Zr02 show interesting properties and are widely used as ionic conductors, coatings and gas sensors in solid oxide fuel cells and structural applications[2]. Most frequently used dopants include Y203, CaO, MgO and Ce02, although other oxides, such as those of rare earth elements, can also act as stabilizers of the high temperature structures. The incorporation of aliovalent cations to the lattice, forming substitutional solid solutions, allows to control the concentration of anionic vacancies in the structure. This aspect is particularly important in designing ionic conductors[3], and is also determinant in the stabilization process[ 4]. The process of stabilization with larger ionic radii dopants is rationalized by the crystal chemistry model[ 5], that describes the dopant cations as typical stabilizer when they have larger ionic size, lower charged state and higher ionicity than Zr4+ The ionic radius of Zr4+ is 0.84 Å and that for La3+ is 1.016 Å [6]."

Jan 1, 2012

By Lianjun Liu, Ying Li, Qianyi Zhang

"Photocatalytic reduction of CO2 by H2O for production of Cl fuels (CO and CH4) was studied using copper and iodine co-modified TiO2 (Cu-IffiO2) nanocomposites, with copper deposited on the surface and iodine doped in the lattice. The nanocomposites were prepared via a combined hydrothermal and wet impregnation process. All I-doped samples demonstrated visible light activity. Under UV-vis irradiation, co-modification of Cu and I significantly increased TiO2 photoactivity compared with bare TiO2 or those modified with only one species.IntroductionThe photoreduction of CO2 into fuels on photocatalysts such as TiO2 has been regarded as an important approach to solve both energy shortage and globe warming problems [1]. However, the wide band gap and fast recombination ofphotoinduced hole (h+) and electrons (e"") limited the application of TiO2 in CO2 photoreduction reaction. Extensive research has been conducted to improve the photocatalytic ability ofTiO2 by depositing or doping foreign ions that can enhance charge transfer and/or creates intra-band-gap states to induce visible light absorption at the subband- gap energy. Compared with mono-doping, co-doping of metal/nonmetal species has been reported to have higher photocatalytic activity for TiO2 [1-3]. Our previous studies showed that Cu deposited on TiO2 [4] or iodine doped in TiO2 [5] significantly enhanced the catalytic efficiency for CO2 photoreduction and increased the response to visible light. We hypothesize that there could be a synergetic effect if TiO2 is co-modified by both Cu and I species resulting in further improvement in CO2 reduction efficiency. In this work, we synthesized and characterized Cu-IffiO2 samples and investigated their activity toward CO2 reduction under visible and UV-vis illumination, respectively.Experimental MethodsMaterialsTitanium tetra-isopropoxide (TTIP, 98%) and isopropanol (C3HsO, 99.8%) were purchased from Acros Organic. Iodic acid (HIO3,99.8%) and Copper Chloride (CuCh, 99.9%) were purchased from Alfa Aesar. All other chemicals were analytical grade and used without further treatment."

Jan 1, 2012

By Dong Hoon Han

The sulfation rates of magnesium oxide and calcium oxide (molar ratio 7:3) contained in calcined CMA ( calcium magnesium acetate) by SO2 were measured. The experiments were carried out in the temperature range 700 to 1100 °C and under the SO2 concentrations of 0.3 to I mol % (5 % 02). In the low-temperature range below 830 °C the reaction produced CaSO4.3MgSO4 and unreacted MgO, but no MgSO4 phase. The formation of CaSO4.3MgSO4 phase has a significant implication in that it allows the utilization of MgO for SO2 removal whereas the sulfation of MgO from conventional sources is so slow that it is of no practical interest. Thus, the calcined CMA can remove SO2 at lower temperatures than conventional SO2 absorbents and at a greater capacity. Above 950 °C only CaO reacts with SO2, but at a much greater rate than the calcined Ca(OH)2, which is one of the most reactive SO2 absorbents.

Jan 1, 1998

By Defeng Zhou, N. Trubaki, Jian Meng, Fanzhi Menga, Xiaojuan Liu, Yanjie Xia

"The microstructure and the electric conductivity of (Ce0.9Nd0.1)1 xMxO2 d (M=Mo, W) solid solutions were investigated. It has been found that their conductivity containing the grain (s gi ), the grain boundary (s gb) and the total conductivity (s t ) at 300°C- 700°C can be ranked as: (Ce 0. 9Nd 0. 1 ) 0.99 W 0.01 02- d (s gi = 0.065 S.cm·1, (s gb = 0.265 S.cm·1, s t = 0.039 S.cm-1) > (Ce0.9Nd0.1)0.99Mo0.01O2- d (s gi = 0.053 S.cm·1, s gb = 0.142 S.cm·1, s t = 0.029 S.cm-1) > Ce0.9Nd0.1 s 2- d (s gi 0.045 S.cm-1, s gb = 0.091 S.cm-1, s t = 0.018 S.cm-1) measured at 700°C. The highest conductivity is obtained in (Ceo.9Ndo.1)0.99W0.01O2 d. These results indicate that (Ceo.9Nd0.1)0.99W0.01O2- d is the most promising electrolyte materials of intermediate-temperature solid oxide fuel cells among (Ce0.9Nd0.1)1-xMxO2- d. IntroductionRare-earth (e.g. La3+, Nd3+, Gd3+ and Sm3l doped ceria-based ceramic materials have been acknowledged to be attractive electrolytes for solid oxide fuel cells operating below 600°C due to their high ionic conductivity [1, 2]. In order to improve ionic conductivity of these electrolytes further, in recent reports [3-6], some aids such as Mo03 [3] etc. in a limited amount can be used which causes extremely high conductivity. For example, Zhou et al. found that with MoO3 doping, the grain boundary conductivity of Nd3+ doped CeO2- d increased notably especially at lower temperatures due to the effect of severely undersized do pants [3]. It is well known that the size of W6+ (rw6+ = 0.60 Å) is close to Mo6+ (rMo6+ = 0.62A) because of lanthanide shrinkage. Thus, rare-earth doped ceria e.g. Nd3+ doped CeO2g with WO3 in a limited amount will be probably good and even better electrolytes. However, much less information is available about these materials. Therefore, in our paper, (Ce0.9Nd0.1)0.99 1-xMxO2- d (M=Mo, W) solid solutions have been prepared and characterized. Much higher conductive electrolytes are found in the series of (Ce0.9Nd0.1)0.99 M0.01O02- d particularly (Ce0.9Nd0.1)0.99W0.01O2- d"

Jan 1, 2012

By Jingbo Liu, Zhimin Wang, Wenchao Li

"IntroductionThe advantages of non-stoichiometric perovskite material are highlighted in many papers[l]and many of this family of materials are well-suited to integration into microsensor devices. Among them, barium titanate is the most promising due to it's piezoelectric, pyroelectric, dielectric properties. Through modification, BaTiO3-based materials can be utilized in many kinds fields, such as surface wave probe; pholoconducting devices, field-effect transistor, permanent memory permanent storage, and ultrasonic transducerl2-3l. In this Paper, a series of BaTiO3-based polycrystals were synthesized by sol-gel processing which appears to be a very promising method for the manufacture of ceramic, because it offers significant advantages such as high purity, chemical homogeneity, controlled particle sizes of ceramics, and lower processing temperatures [4]. In a sol-gel process, alkoxides of the constituent elements show different reactivity toward water so that the preparation of multi-component homogenous system is difficult. In the experiment, inorganic salt was substituted for some of the alkoxides. Acetic acid which is employed for the solvent and catalyst, acts as donor ligand to titanium alkoxide and controls, the hydrolysis polycondensation reaction. Taking these aspects into consideration, we select the system Ba(OAc)2, , La(OAc)3, Ti(O11Bu)4 and acetic acid which is used as both solvent and homogeneous catalyst for the first time.ExperimentalA series of La3+-doped BaTiO3-based nano-crystals were prepared with sol-gel technology using various parameters. The precursor solution was prepared in the presence of barium acetate, lathanium acetate, and titanium tetrabutoxide monomer in butyl alcohol. According to the flow chart (fig. I.), Ba(OAc)2, La(OAch dissolved in the glacial acetic acid (0. lmol/40ml) in a three-neck flask were mixed with a solution of titanium tetrabutoxide monomer in butyl-alcohol(l 7ml/20ml) at room temperature and under constantly, vigorous stirring conditions. In most cases, the resultant solution was golden yellow and stable in the air. To this precursor solution, containing Ba, La, Ti in the desired ratio, water was added incrementally for hydrolysis under continuous stirring until sol was formed. After aging for more than 2 hours, sol was transformed to gel at room temperature. If heated during aging, the gel was formed in a shorter time. The wet gel was allowed to dry at 50°C for more than 10 hours. The dried gel was transparent or light yellow. In order to obtain BaTiO3-based nano-crystals, the amorphous dry gel was calcined at 600°C, 700°C, 800°C, 900°C, 1000°C respectively[5]. The ceramic humidity sensor was formed through the cold-pressed, aged, capsulated routes. The dried gels were crushed in an agate mortar and then pressed into discs of ? 1.5 X l.5mm (l.5mm diameter and l.5mm thickness), then held at about 16.5 MPa pressure for 3 min [6]. The disc was sintered at 1350°C and 1400°C for I hour respectively. During the processing, an Ag-Pt electrode was inserted in the sensor [7]. (See the flow chart.)"

Jan 1, 2000

By A. Pagliero

The coulombimetric reduction method has been used as an evaluation technique for Pb-Ca-Sn anode corrosion in the LIX-SX-EW process. The proposed methodology involves three consecutive steps, i.e., cleaning, oxidation and reduction. They are carried out in the same experimental unit, in solutions containing 180 g/L H2S04 with and without the addition of cobalt. The authors have worked in a wide range of oxidation current densities, from 150 to 500 A/m2 for in a period from 0.5 to 120 hours. It can be concluded from the results that there would be a linear relationship between the applied electrical charge I*T (Coulomb) and the anode corrosion expressed as transformed Pb mass (mg), for solutions with or without the addition of cobalt. The exception is that for the last one the corrosion rate is 5 times faster, which was observed for every layer. From the evaluation of different corrosion layers, one can point out that its composition is mainly in the form of sulphate. In the presence of cobalt, about 67% of Pb would be as sulphate (PbSO4), about 27% as a basic oxide (PbO) and only 6% as oxide PbO2 on the surface. From this result, it appears that great transformations occurred in the metal/sulphate interface. Without the addition of cobalt, the proportion of oxide Pb02 on the surface increased up to 11.5%. According to the previous statement and considering that Pb was found mainly as sulphate, the authors recommend its determination be used as quality selection criterion. Its evaluation should be performed in the acid solutions with 200 ppm cobalt addition at an oxidation current density of 300 A/m2 for a period of 24 hours.

Jan 1, 1999

By Takeo Fujino, Nobuaki Sato, Junichi Hasegawa, Masato Nakazawa, Kohta Yamada

"Tantalum oxide thin films were deposited on quartz substrates by laser ablation of Ta2O5 target using Nd:YAG pulse laser. Deposition-was observed when a laser light energy higher than 200 mJ and its repetition rate higher than 3 Hz. A thin film of 0.1 µm thickness was obtained by the ablation using a laser light of 300 mJ and 6 Hz for 2 sec. The thickness of the film increased with increasing energy, repetition rate and irradiation time of laser. By the SEM observation, it was found that many island-like particles were deposited on quartz substrate forming a thin film. The obtained thin film, which was identified as ? Ta-O by X-ray diffraction, was oxidized to Ta2O5 by the heat treatment in air at I273 K for 3 h.IntroductionTransition metal oxides have a potential to show special characteristics in electrical, magnetic and/or optical properties. When such compounds are fabricated in the form of thin film, the special properties would be improved or new characters would appear in comparison with bulk materials. Tantalum penta-oxide is widely used as a capacitor since Ta2O5 shows high dielectric constants up to high temperatures. The tantalum solid capacitor has been fabricated by the electrical oxidation of sintered Ta metal cylinder followed by MnO2 film coating. However, further improvements, reduction and layered structure formation, are required for compacting the devices. The layered structure of thin films would be applicable for the above requirements. The formation ofTa2O5 film by low pressure CVD1), photo CVD2) and magnetron sputtering3l were reported. The laser ablation -method is one of the most convenient techniques for the deposition of thin films from their compounds, such as oxides. Formation of Ta2O5 film by pulse laser deposition (PLD) method using ArF excimer4), Nd:YAG (533nm)5) and TEA CO2 6 lasers was reported. In these PLD studies, ablation was carried out in relatively high oxygen pressures resulting in formation of Ta2O 5 film. In this paper, the deposition of tantalum oxide thin film by the laser ablation of Ta2O 5 using Nd:YAG pulse laser was examined at a viliety oxygen pressures ranging from 10-8 to 10 Torr. The morphology of the films was also investigated in relation with substrate temperature and oxygen pressure."

Jan 1, 2000

Cospidie (3CaO*2SiO2*CaFe2) is one of the most important compounds crystallized in mold flux films during casting in the continuous casting process of steel, The primary crystallization field of cuspidine has been experimentally developed in the CaO-SiO2-CaF2-SiF4 system. The cuspidine-NaF binary and cuspidine-CaF2-NaF ternary systems have been also experimentally determined to study effects of addition of NaF on the primary field of cuspidine. In order to discuss its thermodynamic stability the standard Gibbs energy of formation of cuspidine has been deterimed by an electromotive force methods using CaF2 as solid electrolyte and a transpiration method as follows: ^fG° (cuspidine) /kjmol-1 = 5198 + 0.825T (+12) (1313<T/K<1329): EMF method ^fG° (cuspidine) /kjmol-1 = 5178 + 0.813T (+8) (1221<T/K<1469): Transpiration method The chemical potential diagram and constituent activities for the CaO-SiO2-CaF2 System have been evaluated based on the obtained thermodynamic data.

Jan 1, 2003

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"Drying (water removal) prior to smelting is always economically feasible. Unnecessary heating of vapour can thus be eliminated resulting in savings of5-15 MUSD every year.Thermodynamically removal of one ton of water out of copper concentrate at 100 °C (with 10 % moisture) requires approximately 3150 MJ/tH2o, consisting of heating of the water (377 MJ), heating of the concentrate (509 MJ) and water evaporation (2260 MJ). This is quite independent of the selected drying technology. In reality some more heat is needed as higher temperature is practiced to enhance the drying performance and to reduce the equipment size.Major nominator in drying energy efficiency is amount of gases, which depends greatly on the drying technology. Dryers based on direct heating with fossil fuels have high gas flow rates, and thus they require additional energy of about 1400-1600 MJ/tH2o, compared to indirect modemsteam drying at 250-400 MJ/tH2o.Significant benefits in energy consumption (900-1300 MJ/tH2o) with additional potential for a bonus profit of 2-4 MUSD/y year, together with full elimination of some 40 000 tpy CO2 per mid-size dryer is available by selecting sustainable, energy efficient steam drying.IntroductionRemoval of water from the concentrate is very energy intensive thus having a significant environmental impact. However, drying prior to smelting is always economically feasible and very often viable also from the perspective of process operations. This environmental impact of drying can, however, be decreased or even fully eliminated with proper selection of the drying technology.Energy incorporated in drying consists always of a number of phases like liquid (water), solids (concentrate) and gases (water vapour, purging I dilution air, combustion gases). Each phase is heated to a specific temperature during the drying process.Heating of water, heating of the concentrate and water evaporation consumes more or less the same amount of energy despite of the drying technology (3150 MJ per ton of water). In conventional drying this amount of energy is achieved by combustion of fossil fuels wirg subsequent CO2 emission. Alternatively, chemical energy derived from sulphide smelting can be utilized in a form of steam thus generating zero emission ofCO2, in modem steam drying."

Jan 1, 2012

By Dirk Verhulst

The Altair Hydrochloride Pigment Process is a new ?third route?, besides the established high-temperature chloride process and the older sulfate process, to manufacture TiO2 pigment from ilmenite ore. It has been tested at a scale of 5 t/day feed. The ore concentrate is digested in high-acid, high total chloride solution (+/- 39% Cl). Titanium and iron both go into solution. Iron is separated as FeCl2 crystals after reduction and cooling. Titanium is transferred by solvent extraction into a purified, high-Ti stream. It is spray-hydrolyzed to produce a TiO2 hydrate and further calcined with additives into high-quality pigment. HCl solutions generated by pyrohydrolysis and spray hydrolysis are treated by pressure-swing distillation to regenerate HCl gas for re-injection into the digestion reactor. All chloride streams are recycled. Recent work has concentrated on optimization, particularly in 3 areas: - Solvent extraction: a new organic mixture, including a new diluent, makes it possible to work at room temperature, to avoid TiO2 hydrolysis problems and to improve phase disengagement and impurity separation. - Pigment finishing: a systematic study of the parameters involved, followed by long runs in the best conditions confirm pigment quality. - Flow sheet optimization: innovative modifications of the conditions of spray hydrolysis and pyrohydrolysis, combined with re-routing of streams achieve significant energy savings. A 100 t/year pilot plant including these features as well as other process improvements is under construction.

Jan 1, 2006

By Yongzhong Xiao, Tiejun Chun, Jian Pan, Deqing Zhu

"An innovative process of reverse floatation-direct reduction-low intensity magnetic separation was developed to effectively beneficiate the superfine run-of-mine (ROM) ore mined from Hunan Province, China. Mineralogy was measured that the ROM ore is of superfine low grade hematite ore type, assaying 27.2wt%Fetotal and with main valuable minerals of hematite occurring at size between 3 to 5µm. The upgrading results show that the final iron concentrate, assaying 88.3wt%Fe total and 94.5% metallization degree was obtained at an overall iron recovery of 69.9% under the following conditions: rough concentration by grinding of ROM up to 88.7% passing 0.074 mm and reverse flotation at pH=9.4, 100 g/t starch and 200 g/t dodecylamine (DDA), and coal reducing the rough concentrate pellets containing 12% calcium containing complex additive at 1200 oC for 120 min, and finally magnetic separation of the reduced pellets by grinding up to 89.2% passing 0.043 mm at 0.08 T field intensity.IntroductionWith the rapid development of iron and steel industry in China, there has been a soaring demand for iron ores in the past decade. The imports of iron ores have increased from 148 million ton in 2003 to 628 million ton in 2009 [1]. Iron making industries increasingly demand for high grade raw materials to improve product quality and reduce operation cost. However, availability of high grade natural ores is limited and enrichment of lower grade ores is necessary to meet the demand. Therefore, large quantities of superfine low grade iron resources are necessary to utilize in China at the moment."

Jan 1, 2011

By In-Hyeok Choi

Currently, spent V2O5–WO3/TiO2 catalysts contribute significant amounts of solid waste following increasing levels of global demand. V2O5–WO3/ TiO2 catalysts usually consist of TiO2 anatase as a supporting oxide, vanadium as a catalytic agent, and other promoters such as tungsten, silicon, and calcium. Although vanadium is the main catalytic agent, a relatively high content of tungsten (WO3, 7–10 wt%) typically exists compared to vanadium (0.5–1.5 wt%). Considering the irreplaceable properties and industrial importance of tungsten, a feasible method for the recycling of spent V2O5–WO3/TiO2 catalyst should be established to utilize it as a secondary source. This paper presents a process to recover tungsten from spent V2O5–WO3/TiO2 catalyst. The processes proposed here involving roasting, decomposition using HCl, ammonia leaching, and crystallization. Within the process, ammonium paratungstate (71 wt% as WO3) is obtained as a final product. The total yield rate of tungsten from feedstock was found to be 96.3%.

By Bin Zhu, Mingmei Zhu, Hong Zhou, Xiaofei Dou, Bin Xie, Yu Wang, Tiancheng Lin

In this study, the formation of 2CaO·SiO2 and 3CaO·P2O5 solid solution (nC2S-C3P) in hot metal dephosphorization process is discussed. The variations of CaO and SiO2 mass, both in nC2S-C3P solid solution phase and liquid slag phase with increasing P2O5 mass in CaO-SiO2-FetO-P2O5 slags were calculated using Factsage software. CaO-SiO2-FeOt-P2O5 slag containing up to 18 % P2O5 was melted at 1823 K then cooled to 1673 K. The contents of CaO and SiO2 both in the solid solution phase and liquid slag phase of quenched samples were observed and analyzed by SEM/EDS. Both the calculated and experimental results show that the contents of CaO and SiO2 in the solid solution phase decreased, just opposite in the liquid slag phase, with increasing P2O5 content in the slags. Formation mechanism of nC2S-C3P solid solution in the slags was derived based on the ionic structure theory of molten slag. The SiO4 4- in the nC2S-C3P solid solution can be replaced by PO4 3- in the liquid phase resulting in the increasing of free Ca2+ and SiO4 4- in liquid phase.

Jan 1, 2015

By Yongqi Sun, Zuotai Zhang

Our study investigated the influence of P2O5 and B2O3 on the viscosity and crystallization behavior of Ti-bearing blast furnace (Ti-BF) slags for the purpose of Ti extraction. The investigation of the crystallization behaviors were carried out using a single hot thermocouple technique (SHTT) and the viscosity was obtained by rotating cylinder method. For the viscosity, the results showed that P2O5 substantially increased the slag viscosity. P2O5 is a network-forming oxide, which increased the degree of polymerization of slags and accordingly increased the slag viscosity. However, both of slag viscosity and apparent activation energy for viscous flow remarkably decreased with B2O3 addition. As a typical network forming oxide, B2O3 was introduced into the network and existed dominantly as 2-D structure, BO3 triangular, which caused a simpler structure and a decreasing slag viscosity. As for the crystallization behaviors of Ti-BF slags, both P2O5 and B2O3 enhanced the crystallization trend of rod-shape rutile and suppressed the crystallization trend of dendrite CaTiO3. Therefore the added P2O5 and B2O3 caused the primary phase change from CaTiO3 to rutile. Additionally, it was found that the rod-shape rutile showed a 1-D growth, whereas the dendrite CaTiO3 showed a 3-D growth style.

Jan 1, 2015

By Ming-Feng Ye, Jun Wang, Guang-liang Wu

In order to reduce the Al2O3 inclusions in 50Cr5MoV roller steel produced by EBT-LF-VD-VC process in a steelmaking plant, the LF refining slag was optimized and the influence of optimized slags with different w(CaO)/w(Al2O3) ratios on reducing inclusions were investigated in the laboratory. The results showed that, when w(CaO) = 50–55%, w(Al2O3) = 25–30% and w(CaO)/w(Al2O3) = 1.5–2.0, this optimized slag can not only reduce massive Al2O3 come from aluminium deoxidation, but also change the remain into plastic CaO-MgO-Al2O3 spherical compound inclusions with 1–5 lm diameter, the harm on the performance of the steel was minimized.

Mar 1, 2018

By C. P. Broadbent

Due to growing .public awareness of environmental issues and greater sensitivity towards waste management, many countries around the world are implementing more stringent legislation governing the storage and disposal of hazardous wastes containing heavy metals such as As, Sb, Pb, Cd or Hg. These wastes can no longer be dumped without providing clear guarantees that the material concerned is environmentally safe and will not leach toxic elements to the surroundings. In the Netherlands the current dumping charge for chemical waste (i.e. worst category) is $280/t, and for industrial waste this cost reduces to $75/t. If the material can be reused there may be a small positive credit for selling it, for example discard slag as an aggregate to the construction industry. A number of (pyre)-metallurgical operations, mostly associated with the extraction of metals from sulphidic ores, produce arsenic residues in the form of As2O3 containing flue dusts and speises. If the flue dust is of high purity it can be sold, though many traditional uses are being substituted by other materials. In many cases upgrading the quality of the arsenical dusts is not possible for either technical or economic reasons. Traditional practice is to dissolve these dusts in acid prior to precipitation as ferric arsenate, which is at present classified by many countries as industrial waste and can be dumped. Recent work, however, has cast doubt on the stability of arsenates for disposal and alternative disposal routes have been investigated. Tests have shown that up to 10% (dm) As can be incorporated into "glassy" silicate slags with very low levels of arsenic leaching in the cooled product. Calcium arsenate was added to a range of synthetic and industrial slags from the system SiO2-FexOy-CaO-A12O3-AsmOn, under mildly oxidising conditions and quenched subsequently in water. It would appear that this represents an environmentally acceptable method for the disposal of many arsenical residues and there is some optimism that this method will be equally applicable to the disposal of other toxic metal residues.

Jan 1, 1994