Search Documents

By S. -H. Jeon, Y. -S. Choi

"The three dimensional current distribution on the rectangular cathode is predicted using a boundary element method with a linear element of trigonal type. The effect of cell geometry and anode shape on current distribution is simulated. Calculated results compare well with experimental results. The proper combination of anode size and distance between electrodes increase the current uniformity.The importance of electrodeposition as a fabrication technology in the electronics industry is large and growing. The main advantages of this wet processing method, in comparison to other dry processing methods, lie in its high yield, rapid processing and low cost. In nearly every application of electrodeposition the pursuit of deposit uniformity, especially thickness uniformity, has been technically imperative. The thickness uniformity of the deposit depends largely on the current distribution over the cathode. The current distribution is primarily determined by the geometrical characteristics of the electrodes and the cell. Also the polarization at the electrode surface and the mass transfer affect the current distribution.The current distribution is an important consideration for those involved in designing electrochemical systems and electroplating systems in particular. Although it is important, the common practice in industry is to use trial and error method to design the cell that optimize the uniformity of current distributions in electroplating. The purpose of this paper is to illustrate the useof boundary element method to predict three-dimensional current distribution in rectangular cell.The calculation of the current distribution is possible by various numerical techniques, which include the finite difference method (FDM)1, the finite element method (FEM)2, and the boundary element method (BEM)3,4. These methods of the numerical calculation have various problems, respectively, but the BEM is considered to be the most efficient. This is due to the fact that the BEM has the advantage of solving field equations only on the surface of a calculation domain. A good comparison between the BEM and the FEM for the secondary current distribution in a Hull cell was made by Matlosz et al.5The fundamentals on the theory of current distribution in electroplating are well-established in the literature by a number of authors.6, 7, 8 However, a small fraction of these works have been specially addressed to three-dimensional analysis, and, mostly thel·10 have focused on the problem qualitatively rather than quantitatively.Extending the previous work to three-dimension, we developed the program for the quantitative calculation of 3-dimensional current distribution using a boundary element method with a linear element of trigonal type. Integrals with singularity from the fundamental solution have been analytically computed and it is shown in detail in the Iiterature11. This paper deals with the three dimensional current distribution for the electrode position of copper in a cubic type cell and the effect of anode shape, size and the distance between electrodes on current distribution is studied."

Jan 1, 1997

By Marcos V. F. Fonseca, Gilson V. Fernandes, Caroline G. de Oliveira, Sergio N. Monteiro, Frederico M. Margem, Anna C. C. Neves

Natural fibers represent an economic and environmental motivation for replacing the synthetic fibers, mainly as composite reinforcement material, which is one of their major applications. Some advantages of the natural fibers are the biodegradability, low cost and renewability. Among the natural fibers, the lignocellulosic ones are highlighted for their high resistance. One of the most cultivated lignocellulosic fibers in Brazil is the Eucalyptus fiber, extracted from the bark of Eucalyptus citriodora plant. In this work, it was investigated the tensile behavior of the epoxy matrix composites reinforced with different volume fractions of Eucalyptus fibers. The specimens were made by pouring the still liquid resin into the mold and laying the fibers onto the resin. The results show a decrease in the tensile resistance with the increase of volume fraction. It is due to the low adhesion between the fibers and the matrix.

Mar 1, 2017

By Susan Fredholm, Randolph Kirchain, Jeremy Gregory

"Jurisdictions across the world have struggled to create and finance systems that can effectively collect and process electronics waste (e-waste). Many different system architectures have been proposed and implemented, but it is difficult for policy-makers and system architects to compare the costs and benefits of different systems, particularly when the systems operate in different contexts. This paper presents a systematic methodology that seeks to address this challenge and uses data from several existing electronics recycling systems across the world to illustrate its implementation. The methodology characterizes three main system characteristics: architecture (e.g., financing and collection methods), context (e.g., jurisdiction population, density, and wages), and performance, both economic and materials collection. A comparison of systems in Europe and North America with different system architectures and contexts illuminates the importance of using the methodology to discern the extent to which architecture and context drive system performance.IntroductionElectronic waste (e-waste) recycling offers several environmental benefits when processing is done responsibly. The controversy around e-waste recycling systems rarely debates such benefits; rather, it focuses on the characteristics of an effective system and whether benefits outweigh costs. Historically, the costs of recycling most electronics have outweighed the value of the scrap recovered. Thus, in the absence of legislation, e-waste recycling systems have been limited to private recycling of high-value waste with minimal consumer participation. E-waste recycling systems now exist in many locations worldwide including Asia, the European Union, Canada and the United States and the amount of related legislation continues to increase. Numerous approaches have been proposed including landfill bans, extended producer responsibility (EPR) and consumer advance recovery fee (ARF) funded recycling systems."

Jan 1, 2008

By S. C. Grand, T. J. Auping, K. Born

Process control, environmental monitoring, budgeting and accounting are based on process data. Without appropriate tools for data analysis, the process data could remain unused and wasted. This paper demonstrates how data reconciliation can be used as a tool to develop closed mass balances. Mass balances are the initial step in plant optimisation (technical, economical or environmental). From mass balances, fundamental process models can be developed. These balances link process parameters (e.g., feed materials) to process performance (e.g., recovery of valuable elements). Some of these models could find their way into simulators useful to plant operators. Classical regression methods regularly fail when they are applied to complex non-linear problems involving a large number of variables. Alternatively, multiparametrical regression analysis can be successfully applied with the aid of neural networks based on reconciled data. Both methods have been applied to plant data originating from the hydrometallurgical zinc plant at Ruhr-Zink, which in this paper serves as a case study. Very promising and useful results were obtained from this study.

Jan 1, 2000

By J. M. Brupbacher, D. C. Nagle

"The XD TM * approach to producing metal matrix composites employs an in-situ precipitation technique for the formation of the reinforcement directly in the matrix of interest. Key features include: thermodynamically stable reinforcement; clean particle/matrix interfaces, single-crystal reinforcement; size, chemistry, and shape control; uniform distribution; compatibility with conventional ingot techniques; and grain refinement.Using XD~ technology it is possible to simultaneously introduce a number of different reinforcements in a given matrix, thus allowing for designing the microstructure to meet a specific material need. Thus, XD1l'1 technology is a very useful technique for achieving ""designer"" or ""engineered"" microstructures. XD TM technology has been applied to a number of systems including AI, NiAI, TiAI and Cu. Materials property and processing benefits will be discussed."

Jan 1, 1988

By Ademar B. Lugão, Sandra R. Scagliusi, Elizabeth C. L. Cardoso

When butyl rubbers are subjected to high energy radiation, they form easy free radicals that initiate various chemical reactions. These reactions alter the molecular distribution of irradiated rubbers by crosslinking or scission affect their physical and mechanical properties. This work aims to the analysis of effect induced by γ-exposure on the crosslinking density in butyl rubbers by swelling measurements accomplished before and after irradiation at 25, 50, 100 and 200 kGy, with further evaluation of crosslinking density accomplished by Flory-Rehner equation; this is a proper procedure for the qualification of radiation resistance. It can be noticed that changes in material structure was due to build-up of new three-dimensional network in studied rubbers. Changes in crosslinking density of butyl rubber compounds emphasize that degradation mechanism is strongly influenced by gamma-radiation doses higher than 50 kGy, since chain scission process predominates over crosslinking reaction.

Mar 1, 2017

By Roderick Guthrie

Gas injection into liquid steel baths is widely practiced, ever since the early days of Bessemer’s pneumatic steelmaking process. What has not been fully appreciated is the critical role of bubble sizes for delivering higher quality commercial steels than is presently possible. This was first proposed by Prof P. Hayes and his research group. Using a full-scale water model of a typical 4-strand Ladle-Tundish-Mold system, we demonstrate the potential advantages of modifying a typical ladle shroud, to generate microbubbles within the water flowing into the tundish. This is possible by taking advantage of high shear rates and turbulence kinetic energy available in that region. These microbubbles enhanced the removal of “micro-inclusions” (hollow glass microspheres) in the 5–50 micron size range, to the upper surface of the tundish. There, they were absorbed into an overlaying “slag” phase. Accompanying CFD studies confirmed that no microbubbles in the size range generated (500–900 μm), pass through the submerged entry nozzles into the moulds.

By W. J. Mitchell

During the months of April and May 1992, the Phelps Dodge Hidalgo smelter underwent a major turnaround. This was the third such turnaround in the life of the facility which was commissioned in 1976. During the third furnace campaign, the smelter processed 5.2 million tons of concentrate producing 2.6 billion pounds of anode copper over a 7.5 year period. The critical path on the fifty-nine (59) day turnaround schedule was the reconstruction of the Outokumpo flash furnace which integrated some modifications with standard rebuild practices. Modifications included incorporation of horizontal cooling jackets throughout the furnace settler as well as the installation of castable refractory in the reaction and uptake shafts.

Jan 1, 1993

By Zhijing Zhang

Long-term thermal stability of ionic liquids is essential for reliable performance of ionic liquids in any engineering applications. TGA studies were carried out on a series of ionic liquids with different cations and anions such as 1-butyl-3-methylimidazolium chloride ([C4mim]Cl), 1-hexyl-3-methylimidazolium chloride ([C6mim]Cl), 1-hexyl-3¬methylimidazolium tetrafluoborate ([C6mim]BF4), 1-hexyl-3-methylimidazolium hexafluorophosphate ([C6mim]PF6), 1-octyl-3-methylimidazolium hexafluorophosphate ([Csmim]PF6), and 1-butyl-3-methylimidazolium bis(trifluromethanesulflonyl)imide ([C4mim][Tf2N]). The short-term thermal stability of ionic liquids was evaluated by measuring the onset temperature of decomposition of ionic liquids, and the long-term thermal stability of ionic liquids was also evaluated by weight loss of ionic liquids over a long period of time at various temperatures. The experimental results showed that the long-term thermal stability of ionic liquids decreased with increasing temperature and was significantly lower than the onset temperature of decomposition of ionic liquids.

Jan 1, 2002

By Carlos A. Nunes

V-AI alloys have been used commercially to produce pure vanadium by Electron Beam Melting (EBM), as well as to obtain Ti-based alloys (ex. Ti-6AI-4V). The aluminothermic reduction of vanadium pentoxide (V205) is the primary method to obtain these alloys. Concerning the obtention of pure vanadium, earlier studies have indicated alloys presenting Al content between 10 and 15wt% as the most suitable alloys for direct EBM. In the present work we investigated the aluminothermic reduction of V205 in order to define process parameters for the obtention of V-AI alloys with composition in the previously mentioned range. It was studied basically the effect of excess AI, CaO addition and reaction atmosphere (air, argon) on the alloy composition (AI, 0, N). In addition, microstructural analysis of selected alloys by SEM (BSE images) and EPMA (WDX) were also performed.

Jan 1, 1996

By Pekka Taskinen

The converter-less nickel matte smelting technology (DON) adopted more than 20 years ago in Boliden Harjavalta smelter has been since that applied successfully to the processing of large number of nickel sulphide concentrates of various Ni-to-Cu ratios and MgO contents. The operational point of the technology is far from the conventional primary nickel smelting in the smelting-converting route. Therefore, a careful scouting of distribution equilibria of the base and trace elements in the smelting conditions of DON process has been conducted, in order to obtain quantitative information about the equilibria and thermodynamic properties of the nickel mattes at low iron concentrations, less than 10 wt% [Fe] in matte. The series of investigations has included novel experimental and analytical techniques for increasing the reliability and sensitivity of the phase equilibria as well as the element distribution observations carried out in typical high-grade nickel matte smelting conditions.

By Adolfo Pillihuaman, Alberto Nogueira, Cyro Takano, Marcelo Mourão

The organic household waste has a growing disposal problem, requiring costly disposal systems. It is necessary to find new applications for these materials; one could be the steelmaking raw material production. In this paper is studied the development of self-reducing pellets from the organic waste pyrolysis, where is generated carbon and condensable and non-condensable volatiles. Non-condensable volatiles were burned and condensable volatiles were recovered. The resulting tar was mixed with iron ore, coal powder and flux (CaO), to then be pelletized together. Compression, falls and tumbler tests were conducted to characterize the pellets before and after heat treatment and reduction processes. The reduction curve and their physical and morphological characterization were measured. The results were as was expected, the fluidized coal create sufficient adhesion that pellets earned resistance with an equivalent resistance of common pellets, showing a good feasibility of this process.

Jan 1, 2015

By Shigeru Ueda, Shin-ya Kitamura, Dong Jun Shin, Xu Gao

Steelmaking slag contains useful elements such as P and Mn. Generally, in the carbothermic reduction of slag, not only P but also Mn are reduced and a Fe–P–Mn alloy is formed. In this study, the possibility of the separation of Mn and P was investigated. A mixture of synthesized slag and graphite was heated at 1773 K, and the compositions of the separated slag and metal were analyzed. The results showed that with a decrease in basicity, the reduction of P was enhanced but that of Mn was suppressed. Thus, under an optimum condition, steelmaking slag was separated into a Fe–P alloy and a high MnO-containing slag. Although further investigation is necessary, the formed alloy and slag could be used as raw materials for fertilizers and Fe–Mn alloys, respectively. This paper elucidates the concept of this process and the results of the fundamental experiments.

Mar 1, 2018

By Sue Xue, Carl C. Nesbitt

A project was completed which investigated the efficacy of recycling lead or lead monoxide from various fire assay wastes including crucibles, cupels and slag. The scope of the project was to determine optimal hydrometallurgical parameters so that direct separation and recovery of lead salts was economically feasible. A process was developed from the study which could use either acetic acid or nitric acid as a leachant, followed by several precipitation processes which could directly recover litharge (PbO) or other lead salts, such as lead carbonate or lead sulfate. The economics of the process is discussed. Analytical equipment such as the atomic absorption spectrophotometer and x-ray diffractometer supplied much of the information required for the study. However some novel analytical approaches using these instruments had to be developed to help in the determination of leaching kinetics and process quality control which are discussed.

Jan 1, 1999

By Guozhi Lyu, Ting-an ZHANG, Biyu Long, Yajing Tian, Xuejiao Cao, Weiguang Zhang

Aim to the separation problem of high concentration V–Fe in stronger acidic leaching solution of vanadium slag, a novel chelating extraction system is proposed to separate V and Fe. Influence factors including initial pH value, the extractant concentration, the phase ratio, temperature and time are investigated. The experiment results show that single extraction rate of V and Fe reach 85.57 and 0.39% respectively, when pH value is −0.4, organic phase composition is 30% Mextral 973H + 70% sulfonated kerosene oil, O:A = 1:1, stirring time is 10 min, extraction temperature is 30 °C. The industrial experiment results of three levels countercurrent extraction show that the total extraction rate of vanadium and iron can reach 97.44 and 0.23%, separation factor is 6410. The effective separation of V and Fe in high acid and high iron solution can be accomplished.

Mar 1, 2018

By V. L. Stolyarova

As part of an effort to develop the fluoride electrolysis route for the production of rare earth metals and alloys, a study of the thermodynamic properties of DyF3 has been carried out by Knudsen cell mass spectrometry. A quadrupole mass spectrometer QMS 420 was used in conjunction with the Knudsen cell arrangement. The experiments were carried out in the temperature range 1280-1440 K. Vaporization was carried out from platinum, molybdenum and tantalum cells. The Dy*, DyF+, DyF2+ fragment ions and the DyF3 parent ion were identified in the mass spectrum of the DyF3 vapour. The DyF, vapour pressure was obtained by the complete isothermal vaporizadon method as well as the ion current comparison method, and the enthalpy of sublimation of DyF3 was evaluated. From the DyF3 vapour pressure data obtained at different temperatures, the enthalpies of formation of DyF3 in the gaseous as well as condensed phases have been evaluated. The experimental data are compared with the thermodynamic information available in literature.

Jan 1, 1995

By S. N. Monteiro, L. G. Pedroti, D. P. Santos, M. S. Peixoto, G. C. Xavier

The Baixada Campista is a region located in the municipality of Campos dos Goytacazes and is known as an important pole producing ceramic artifacts in Brazil. The clay used in this production is usually extracted from different layers of the region itself undergoing a pretreatment process. The objective of this work was to characterize the different soils (A, B and C), from different layers of the reservoir, in order to characterize the different physical and chemical characteristics (granulometry, determination of Atterberg limits, moisture and chemical analysis). To optimize, using the simplex methodology, properties such as mechanical strength, porosity and linear retraction. The results pointed to an optimum proportion of the clays studied so that the properties meet the Brazilian technical norms, being the proportion of 30% of soil A, 30% of soil B and 40% of soil C well.

Mar 1, 2018

By Juliana Augusto Molari, Deborah Dibbern Brunelli, Leonardo G. de Andrade e Silva, Patricia N. S. Poveda

There are several additives aimed on improving the processing characteristics as well as mechanical properties of the plastic materials. Being polypropylene is one of the main polymers used in the plastic processing industry due to its easy processability and application versatility, was chosen as the base resin for this study. Additives can aid the processing of polypropylene, either by promoting a better slip between the chains (lubricants), or by contributing to nucleation and crystallinity (nucleating). In this study, the raw materials copolymer polypropylene, lubricant (internal and external action), organic nucleating agent (metallic salt) and inorganic nucleating agent (metallic oxide) were considered. Mechanical tensile tests, Charpy impact and spiral flow to verify melt index were performed to characterize the samples with additives and standard (copolymer polypropylene). The interference of these additives with polymeric matrix was observed.

Mar 1, 2018

By Bob Hannah, Peter C. Hayes

The changes that are happening in the world of metallurgy, and with it university education, are generational and require generational responses. Some of the key issues facing metallurgical education and ongoing professional training are explored. What will be required of metallurgical engineering professionals in the coming decades? What knowledge and skills will be needed? How to provide the educational and learning pathways, and how to attract smart young people into this profession? These are issues more readily addressed by tertiary institutions in conjunction with industry; perhaps the greater challenges lie in building and maintaining competencies post-graduation. There is a need to establish and maintain a system that supports graduates and enables them to develop further into competent expert engineers able to successfully address complex engineering challenges.

Jan 1, 2014

By Marcos V. F. Fonseca, Djalma Souza, Luiz G. X. Borges, Sergio Monteiro, Caroline G. de Oliveira, Ygor M. de Moraes, Janine F. de Deus, Frederico M. Margem

Recently, the natural fibers have been studied as alternative reinforcement material to the use of synthetic fibers. Aiming to improve the properties of natural fibers composites, it is investigated the use of natural fibers fabrics, since they provide multidirectional reinforcement and enables the introduction of a larger fiber volume fraction. In this work, it was investigated the tensile behavior of the epoxy matrix composites reinforced with different volumefractions offabric made of Ramie, a highly resistant lignocellulosic fiber. The specimens were made by pressing the fabric with liquid resin to guarantee total impregnation, and then cutting the fabric in the mold format. Finally ,the fabric layers were placed into the mold with the liquid resin and catalyst. They were cured for 24 h and tested. The results revealed an increase in the tensile strength and almost no effect in the elastic modulus with the increase of fabric volume fraction.

Mar 1, 2017