Search Documents

By A. N. Lasseigne

Hydrogen storage capabilities of LaNi5 intermetallic compounds were investigated utilizing the combination of thermoelectric power, Beeghly Ester-Halogen digestion, and Leco hydrogen determination. Thermoelectric power has demonstrated a rapid hydrogen assessment capability and can achieve the equivalent of the pressure-composition-temperature (activity) diagram. Effective use of hydrogen storage materials occurs in the two-phase, alpha+beta region of the PCT diagram. A thorough assessment of the content of each phase in this two-phase region to optimize performance of the hydrogen storage materials is described. Practices using the combination of these three analytical practices for rapid characterization of LaNi5intermetallic alloys are discussed.

Jan 1, 2006

By Felipe P. D. Lopes, Ailton Silva Ferreira, Sergio N. Monteiro

"Environmental issues such as global warming and water pollution are motivating fast changes in scientific and technological paradigms. Special importance is now being given to the so called environmentally friendly materials, which are renewable, recyclable and biodegradable. An example is the natural fibers with increasing industrial applications beyond the conventional uses as baskets, fabrics, ropes and carpets. In addition to traditional natural fibers, others like curaua (Ananas erectifolius) are being investigated for possible use as reinforcement of industrial composites. Since epoxy matrix is not yet incorporated with curaua fibers, the objective of this paper was to study the basic properties of epoxy composites reinforced with different amounts of curaua waste fibers. A comparative analysis aiming at the use of these composites as substitute for conventional building materials was carried out.IntroductionThis new millennium, which initiates with the 21th century, is experiencing a fast degradation of the environment by pollution and climate changes. Most of the problems are related to our methods of development associated with the use of fossil fuels and the energy intensive processing and production of synthetic materials. As a consequence, environmental issues such as global warming and ocean pollution are motivating rapid changes in technological paradigms. One relevant example is the current importance given to natural materials like the lignocellulosic fibers extracted from cultivated plants or found as industrial wastes [1]. These fibers are considered environmentally correct alternatives to substitute energy intensive conventional synthetic fibers such as carbon, glass, nylon and aramid. In addition to the renewable recyclable and biodegradable nature of the lignocellulosic fibers, the low cost and abundance in developing regions are major advantages that justify their increasing application as reinforcement of composites [2,3].In fact, nowadays, the use of natural fibers is no longer restricted to baskets, ropes, clothes and carpets. Industrial composites are introducing these fibers in large technological segments associated with car making, building construction and furniture [4,5]."

Jan 1, 2008

By M. Save, N. Menad

"This paper gives the overview of different alternatives to recycle the following wastes: slag, dusts, wastes of electric and electronic equipment (WEEE) and auto shredder residues (ASR). Based on modified Bogue calculations, steelmaking slags were combined in order to produce a belite-rich clinker activated with sulphoaluminate. The EAF dusts containing significant amount of metals can be recycled in different ways: The carbothermal treatment and INTECT process are reported. The results obtained from the model of Auto Shredder Residue injection into blast furnace show that ASR can be used as reducing agent in the BF process if certain conditions are met. The particle size of this material must be controlled to ensure optimal gasification of the material in raceway. The non-ferrous contents may affect the pig iron quality, which is difficult to rectify at a later point. It seems the pyrolysis is the most attractive process to handle ASR. The BRGM flow sheet of WEEE treatment is also reported.I. Introduction The activities of human been may generate wastes and by their accumulation during several years, these wastes may have an impact on the environment and on the human health. These wastes can be generated in the forms of solid, liquid and gas. A variety of industrial wastes can be recycled for use as products. There are three ways in which industrial waste recycling occurs: at the facility itself (on-site recycling), at commercial facilities that gather waste streams from several companies (off-site recycling), and at a company that uses as inputs in its production process the waste products of another company. The industries producing iron and steel may generate different solid wastes which are classified in three main categories: 1. Ferrous material (mainly dusts and sludges from gas cleaning), 2. Slags (these by-products are generated from different process stages), 3. Others by-products (including refractories and material generated from engineering activities). According to this review, the most quantity of the metallurgical wastes is deposed. Currently, the public opinion opposes the creation of new sites. This leads to the growth of the waste disposal costs. Such situation reduces the enterprise competitiveness and decreases their market share on regional and/or national and/or world scales. In these conditions, the economical activities can be decreased leading probably to social problems. The problem of wastes and/or by-products can be treated on three levels:"

Jan 1, 2008

By Alex Moyano

The Peirce-Smith converters are traditionally carrying out the converting process of a copper matte in the smelters of Codelco-Chile. However, its production increment is very limited due to the investment magnitude associated to the fulfillment of the environmental regulation. The objective of this paper is to present the Codelco continuous converting process technological advance when converting mattes and/or white metal into blister copper in a Teniente converter unit as an alternative to increment the corporative anode copper production. In 1994, Codelco-Chile started evaluating its ?home made technology? as an alternative to the traditional batch-type converting process. By the year 2001, the Caletones smelter converted liquid white metal to blister copper in a rearranged PS converter continuously. Then, during the 2001-2003 period, several pilot and industrial scale tests were done in a Teniente converter unit at Codelco Norte smelter, evaluating the continuous converting process, i.e., processing liquid mattes (62-68% Cu) to blister copper, demonstrating its technical feasibility with: (i) both constant production of gas flow and SO2 concentration, (ii) production of liquid slag, and (iii) production of a clean blister copper, suitable for the refining process. The promising results have led Codelco-Chile to plan for the 2006 period, a next advanced stage for the continuous converting process evaluation by carrying out a new campaign of tests in a Teniente converter unit at the Codelco Norte smelter.

Jan 1, 2006

By Hubert Bril, Priscilla Pareuil, François Bordas, Emmanuel Joussein, Jean-Claude Bollinger

"According to the legislation, valorization type, origin and characteristics of waste material, various standard procedures are available to evaluate environmental impacts. A Mn-rich slag was sampled from a metallurgical plant. After its characterization (elementary analysis and mineralogy), five standard procedures were carried out (i.e. TCLP, EN 12457-1). Each fixed parameter of the standards was systematically studied in a large range: pH, Liquid/Solid ratio, contact time. For example, EN 12457-1 led to a low ME mobilization, increasing with the L/S ratio, the contact time and an acidic pH. As a conclusion, the representativeness of the considered parameters and their potential variations are predominant to assess of the real environmental impact during slag reuse. Introduction Recent studies have been carried out about environmental impacts of waste containing metallic elements (ME) because of their potential mobility [1-7]. Indeed, slags are either dumped or valorized in various activities such as building materials. In order to assess environmental risk, various standard procedures are used depending on country legislation, origin of waste and valorization way. Results of leaching tests are linked either to special legislation (e.g. Dumping: EC, Council Decision 2003/33/EC, Construction products: EC, Council Directive 89/106/EEC) or to legal levels used in drinking water (Directive 98/83/CE) when leachates could migrate to groundwater. If ME in leachates are lower than drinking water authorized levels, the waste will be considered as non-hazardous. On the contrary, if the leachable amounts exceed them, the question about the risk has to be posed. Beyond the abundance of leaching tests available, variety of operational conditions induced by these regulatory tests does not make the choice easier. According to operational conditions induced, ME release could vary from one test to another one. ME concentrations in leachates depend on pH, Liquid/Solid ratio, contact time and particle size [3]. To highlight the importance of these operational parameters, potential risk for valorization of a manganese-rich slag was assessed by comparing several standard leaching protocols [8-12] with a global study dealing with the influence of operational conditions. For each regulatory protocol, the most influential parameters (L/S ratio, pH, particle size and contact time) have been studied in a large range."

Jan 1, 2008

By Atinuke Oladoye, David Esezobor

"Particulate Copper Silicon carbide (Cu-SiCp) composites find application as wear and heat resistant materials in electrical sliding contacts such as in homopolar machines, railway overhead current collector systems where high electrical/thermal conductivity combined with good wear properties is required. However, challenges occur during machining due to the presence of hard reinforcement in the matrix. This may lead to high turnover of tool wear and poor surface finish. The adoption of near-net shape technology to produce such hard-to-machine metal matrix composites and subsequent finish machining with its attendant cost has reported limited success. This paper critically appraises the challenges and opportunities in the improvement of tribological characteristics of particulate Cu-SiC composites and identifies low cost reinforcement material that could be used to improve its tribological characteristics.IntroductionTribology consideration is increasingly becoming a decisive factor in the design and selection of materials for applications involving interacting surfaces in relative motion. The consideration is mainly on the combined effects of friction and lubrication on material's wear integrity and performance amongst other. Annual losses due to tribology in the US industries are estimated at between 1-2% of the Gross National Income [1], in Russia it is about 1-4% of the GDP [2]. Thus, the attributes of tribology has become imperative in modem machinery especially those applications involving sliding and rolling surfaces, and electrical contacts [3- 8].These are readily found in homopolar machines, internal combustion engines, aircraft engines, gears, cams, seals and railway overhead current collector systems [9-12]. In these systems, the dissipation of frictional heat arising from the interacting surfaces as quickly as possible imposes constraints on the choice of materials for such application to prevent softening, plastic and shear flow and the transfer of metal as wear debris onto the interacting surfaces. If these possibilities occur, system performance is compromised and premature failure may result. Materials for these systems are expected to possess high electrical and thermal conductivities, low coefficient of thermal expansion, good corrosion resistance and high melting point [3-8, 13]."

Jan 1, 2011

By Tuomas Hirsi

The world’s first large scale modular solvent extraction plants have been delivered by Outotec. The first of these is now in operation and has proven that the VSF®X technology can deliver the excellent performance of the Outotec VSF® solvent extraction process. Modular delivery allows site work to be minimized and the manufacturing done in a controlled environment, allowing for serial production manufacturing benefits. Container based delivery was found to be a highly efficient way of utilizing the standardized transportation methods on a global scale. Site work with modular units was found to be efficient and highly predictable. In this paper, we present the first successful Outotec VSF®X deliveries and discuss the benefits of the modular delivery and design compared to the standard solvent extraction installation’s delivery. The process performance of the VSF®X is also discussed with experiences from the first industrial reference presented.

By Baoxiang Zhang, Jing Zhang

"As extruded Mg-9Zn-0.6Zr-2Er magnesium alloys were hot-rolled at 400°C, followed by solution treatment at 400 °c for 1. 5h and artificial aging at 200°C for 10h. Microstructures and tensile mechanical properties of the alloys after hot rolling, solution and aging treatment were examined respectively. Optical micrographs of the as-rolled and as-solution alloys showed fine grain structures, due to the formation of Er-and Zn-bearing compounds at grain boundaries which obviously improved the thermal stability of the alloy. Yield strength as high as about 335 MPa was obtained for the as-rolled alloy, showing that the mechanical properties of the alloy was greatly benefit from the grain refinement and dynamic precipitation of fine MgZn2 during hot rolling. Due to solution heat treatment, vast majority of the Mg-Zn phases dissolved into the matrix, and precipitated out again as fine dispersoid during the subsequent aging, resulting in an enhanced aging-hardening effect.IntroductionWith high specific strength and low density, magnesium alloy has stimulated significant interest for the applications in microelectronics, aerospace and automobile industries. Due to its HCP structure, magnesium alloys exhibit relatively poor strength and ductility. Great efforts have been made to improve the properties of magnesium alloys.Thermo-mechanical processing which combined with subsequent heat treatment can strengthen magnesium alloys due to the strain-hardening mechanism, homogeneous distribution of second particles and grain refinement [1, 2]. However, commercial wrought magnesium alloys have high tendency of grain growth at high temperature due to lack of effective solutions to stabilize the microstructure [3, 4, and 6]. But Magnesium-RE alloys containing high rare earth were reported to have remarkable thermal-stability, Rare earth (RE), such as Y, Nd, Yb, Gd, Ce, were known to form second-phase particles that have higher thermal stability combining with Zn and matrix in Mg[12-17]."

Jan 1, 2012

By A. René Silva

The separation of Fe(III) from simulated Ni(II) solutions using different ion exchange resins was studied. The resins tested included cation exchangers with sulfonic and carboxylic groups and chelating resins with iminodiacetic, aminophosphonic, and mixed sulfonic and phosphonic groups. The dosage of resins was varied from 0.1 to 0.5 g/mL to study the impact of resin type and dosage on iron separation from simulated nickel leach solution containing 25 g/L Ni(II) and 25 g/L Fe(III) at pH 1.5. Also, the effects of different metal ion concentrations, Fe (III):Ni(II) ratios in solution, pH, and adsorption times were investigated. Experimental results demonstrate that all the chelating resins selected favored the adsorption of Fe(III) over Ni(II) with high Fe(III) loading. Soft cation exchange resins also favored the adsorption of Fe(III) over Ni(II), but no significant Fe(III) loading was observed. In contrast, strong cation exchange resins did not show adsorption preferences. The most efficient separation was observed using resin with aminophosphonic groups at resin dosage of 0.2 g/mL, having a Fe(III) adsorption over 94% and Ni(II) adsorption below 5%.

By Xinli Wang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng, Byoung-Gon Kim

"The microwave dielectric properties of silicon dioxide at frequencies of 915 and 2450 MHz were characterized in the temperature range of 24 to approximately 1000 °C using the cavity perturbation technique. It is shown that the relative dielectric constant of silicon dioxide at both frequencies remains almost unchanged below 500 °C, above which there is a slight increase of 2%. The relative dielectric loss factor of silicon dioxide exhibits a strong temperature dependence above 500 °C and increases by approximately 7 and 5 times at 915 and 2450 MHz, respectively. The substantial increase in the relative dielectric loss factor is mainly attributed to the enhanced dielectric polarization and accelerated electrical transport in silicon dioxide at elevated temperatures.IntroductionSilicon dioxide (Si02) is usually considered a microwave transparent material due to its poor absorption capability at room temperature [1]. This characteristic has led to various applications of silicon dioxide in microwave processing of materials and communication. For instance, Si02 has been used to produce sample holders for microwave heating and substrates for electronic devices [2,3]. These applications generally require the material to withstand high temperatures under microwave irradiation. This indicates that microwave absorption capabilities of silicon dioxide at elevated temperatures are also important for its utilization.The microwave absorption capability of Si02 can be determined based on dielectric characterization (permittivity measurement) of the material at commonly used microwave frequencies, 915 and 2450 MHz, in a broad temperature range. To date, however, no detailed work on the dielectric properties (permittivity) of silicon dioxide at high temperatures has been reported. The present work is aimed to study the dielectric properties of silicon dioxide from room temperature to approximately 1000 °C at 915 and 2450 MHz. The results show that the permittivity of silicon dioxide has a strong temperature dependence above 500 °C, suggesting a substantial increase in its microwave absorption capability."

Jan 1, 2013

By Tsutomu Yamamura

The electrolytic reduction mechanism of rare-earth chlorides such as LaCl3, CeCl3, NdCl3, ` SmCl3 and DyCl3 in alkali chloride baths has been investigated in NaCl, KCI and eutectic LiCI- KCI by means of electrochemical transient methods. The thermodynamic behaviors of rare-earth containing species have been discussed in the frame of Electrode potential - P02- diagram. Low current efficiency found in the case of Nd electro-winning has been attributed to the dissolution of Nd into the bath. The analyses of electrochemical measurement required the elucidation of the effects of the factors such as under-potential deposition, metal dissolution, moisture and oxygen partial pressure.

Jan 1, 2003

By Upali Siriwardane, Tushar V. Kudale, Naidu V. Seetala

"Cellulose acetate (CA) membranes with 25% triethyl citrate (TEC) as plasticizer were prepared with varying thickness for CO2 gas separation from water-gas-shift (WGS) reaction products. The AFM analysis of the CA membrane showed that the uniform coating had fewer and smaller pores as the film thickness increased, and corroborated by gas permeability studies. The CO2 permeability has decreased faster than CO permeability with the CA/TEC membrane thickness, and findings support that the CA membrane could be used to entrap CO2. Several CA/TEC membranes were also staked to increase the separation efficiency. Positron Annihilation Lifetime Spectroscopy (PALS) was used to estimate the nano-porosity (pore size and concentration) changes of CA/TEC films. PALS results show a decrease in pore size with increasing CA-TEC concentration in acetone, while the pore concentration increases. The PALS results are correlated with the CO2/CO permeability variations as the CA-TEC concentration change.IntroductionHydrogen is one of the main energy sources available for the future advancement of clean fuel technologies especially for fuel cells. Generation of hydrogen and CO2 from Water Gas Shift (WGS) reaction mixtures of CO and H2O is of interest to many researchers since it allows a large scale production of hydrogen [1, 2]. Once hydrogen is produced using the WGS reaction, the output products contain mixture of CO, CO2, H2, and water vapor. Metallic membranes have been used as hydrogen separation membranes [3-6]. As H2 is separated from the mixture using the metal membranes, we need to separate CO2, and find ways of sequestration of CO2 to avoid environmental problems by greenhouse gasses. Polymeric Membranes have been used for CO2 separation [7]. Plasticizer can control the micro-structural properties such as pore size and concentration of polymer membranes [8], which influence the size/molecular weight dependent diffusion rates of the gas molecules. We have used cellulose acetate with triethyl citrate as plasticizer to separate CO2 from the WGS reaction products. Positron annihilation lifetime spectroscopy (PALS) is very sensitive and able to identify different kinds of defects and their agglomerates such as vacancies, vacancy loops, and voids [9, 10]. PALS has been successful in determining the free volume in polymers that influence the properties of the polymers [11, 12]. Microscopic properties of the free volume obtained from PALS have been correlated to macroscopic properties [13, 14]. We used PALS to study the nanoporosity (pore size and concentration) and fractional free volume changes of CA/TEC films, and used to understand the variations observed in the CO2/CO permeability as the CA-TEC concentration in the membranes change."

Jan 1, 2014

By Glenn Stevens

After 40 years of operation with the original design, Pan Pacific Copper determined it was necessary to rebuild the Saganoseki Flash Smelting Furnace to continue safe operation. The original design employed a rigid steel frame, which, through hearth growth, led to severe distortion of the frame. Contributing to the continued growth of the hearth were thermal cycles that occurred during the government mandated annual shutdowns. Hatch designed a unique sprung bound, pivoting binding frame to maximize crucible size within the existing furnace footprint, while integrating the PPC designed cooling jackets. The bound system maintains tight brick joints, while the new conductive hearth design with integrated bottom cooling produces a protective freeze layer to accommodate higher furnace throughput. Minimization of furnace downtime for the rebuild was achieved through effective construction planning, highly trained contractors, and through an efficient start-up and ramp-up to full production.

By K. Adham, T. Buchholz

Debottlenecking of high temperature processes within an existing metallurgical plant can significantly increase the throughput to meet new production demands. Modeling and simulation can help to fulfil that aim through incremental changes and operational improvements, rather than the more expensive option of building new plants and facing new environmental and infrastructure challenges. This paper describes a methodology of how modeling tools can be used to simulate the processing steps, how to estimate their existing and ultimate capacities, and how to determine the minimum cost points for a plant capacity expansion. This technique is presented through a generic description that can be applied to different metallurgical processing studies. We start with heat-and-mass balances, draw a bottleneck diagram, brainstorm capacity increase options, and prepare a cost-capacity curve. Hatch has successfully applied this technique to a number of plant capacity studies, with great benefits to our industrial clients (Adhametal et al. in A Success Path from Process R&D to Commercial Plants, Montreal, Canada, [1]).

Mar 1, 2017

By Heng Yi

The salt lake brines that lithium is extracted from have high chloride levels making the brine very corrosive to stainless steel extraction column internals. This is a significant problem in column scale-up to industrial production. Two types of corrosion-resistant ceramic internals, the hybrid ceramic internal and ceramic plate, were designed and tested under pilot conditions for future industrial application in this field. The hydrodynamic results (Yi et al. Ind Eng Chem Res 56 (4):999–1007 (2016), [1]) show that holdup of hybrid ceramic internal is higher than that of ceramic plate by around 50%, while Sauter mean diameter when using the hybrid ceramic internal is smaller than when using the ceramic plate by around 30%. This results in a larger mass transfer area, hence better mass transfer efficiency for the hybrid ceramic internal. Axial dispersion and mass transfer parameters are also examined (Yi et al. Ind Eng Chem Res 56(11):2049–3058 (2017), [2]). The results show that the column with hybrid ceramic internals has 50% lower axial dispersion coefficient and 50% higher mass transfer coefficient, leading to higher mass transfer efficiency. The transfer unit height of the column using hybrid ceramic internals can be as low as 0.2 m, showing very good efficiency. This is promising for near-future applications. Two-phase computational fluid dynamics (CFD) models have been developed for the two columns with ANSYS FLUENT commercial software. CFD successfully predicts the higher holdup and lower axial dispersion coefficients for the hybrid sieve plate pulsed column as measured in the experiments, and the cause for the difference in performance has been explained with information from CFD.

By Ender Keskinkilic

Continuous casting of slabs is conducted with two successive steel flows: first from ladle to tundish, then from tundish to mold. There are certain process abnormalities related to ladle, tundish and mold. For example, change of submerged entry nozzle (SEN) is the one encountered during steel flow from tundish to mold. Tundish exchange is the abnormality taking place due to replacement of processed tundish with the new one at rest. Another example is the flow of steel from ladle to tundish without a ladle shroud. In this study, a statistical analysis was conducted related to the process abnormalities in slab casters of a steel plant. Slab surface defects observed in slab yard was incorporated in this analysis.

Mar 1, 2018

By Kimio Itagaki

The distribution behaviours of the VA elements between the gas, slag and matte phases in copper smelting were evaluated on the basis of the thermodynamic data, most of which were determined by the authors. The distribution is basically dependent on the process factors such as temperature, the content of the element in charge, the amount of the waste gas and degree of vapour saturation with the elements. The thermodynamic quantities such as the activity coefficients of the VA elements in matte, the activities of iron and copper, SO2 or 02 potential and the distribution ratio of the elements between the slag and matte phases seriously affect the distribution, and the behaviours in various smelters could be explained systematically and reasonably by considering the changes in these quantities, In oxidation smelting at PSO2= 0.1 to 1 atm, the proportion of arsenic and bismuth in gas is predomi22t for the arsenic and bismuth distributions in both smelting and converting stages. The degree of vapour saturation has serious effect on the distribution, and sufficient contact between gas and matte phases is desirable for transferring arsenic and bismuth into gas phase.The elimination of antimony by means of vaporization is not significant. In reduction smelting at po2 = 10-11 atm, the proportions of arsenic and antimony in the gas phase are quite small, but the proportion of bismuth does not change significantly.

Jan 1, 1983

By Niander A. Cerqueira, Pâmela Berçot, Afonso G. Azevedo, Victor B. Souza, Victor T. Bartolazzi, Bruno Padilha

In recent years, concern about environmental issues has become a parameter to consider in the projects in engineering. In order to reduce the impact that the tire improper disposal may result for the environment, we sought a solution to this problem. This article proposes the use of rubber scrap tires as fine aggregate in concrete production. The material produced was analyzed by a bending test, resulting in product quality, in particular for application in situations requiring a more ductile material.

Mar 1, 2017

By C. M. Wai

"Metal species in solid and liquid materials can be extracted by supercritical carbon dioxide containing a suitable ligand. This in situ che1ation-supercritical fluid extraction technique offers several advantages over conventional solvent extraction including minimization of organic liquid waste generation and exposure of personnel to organic vapors. One unique feature of this technique is that metal species can be removed from solid materials directly using supercritical carbon dioxide as a solvent. Several ligand systems including dithiocarbamates, B-diketones, organophosphorus reagents, and macrocyclic compounds have been tested for metal extraction in supercritical carbon dioxide. This novel extraction technique may have important applications for metal recovery and mineral processing.IntroductionSupercritical fluid extraction (SFE) offers several advantages over conventional solvent extraction including the minimization of organic liquid waste generation and exposure of personnel to organic vapors.[1] The high diffusivity, low viscosity, and T-P dependence of solvent strength are some attractive properties which make supercritical fluids excellent candidates for extraction and recovery of organic compounds from solid materials [2] Carbon dioxide is a gas of choice for SFE because of its moderate critical constants (Tc = 31 °·C and Pc = 73 atm), inertness, and availability in purified form. After extraction, the fluid phase is depressurized to separate organic solutes from CO2 gas and the gas can be recycled for repeated use. The SFE technology has been applied to industrial scale operations such as the preparation of decaffeinated coffee and hop extracts."

Jan 1, 1996

By Ulrich Kerney

In 1996, bath smelting technology for lead recovery from concentrates and secondary materials was introduced in Nordenham to replace the common sinter plant/shaft furnace operation. Since start-up, a continuous improvement of equipment and operation lead to a steady increase of capacity and plant availability. The decision to skip the reduction stage for slag treatment now allows the treatment of 200000 t/a feed materials with a secondary fraction of up to 70 %. The main feed source for the furnace is automotive battery recycling, which offers oxide paste and metallics to be molten under oxidizing conditions in the lance fired furnace. The lead bullion is transferred to the refinery, where copper, silver and other impurities are removed. Silver is recovered as doré quality. All loopings are recycled to the BSF. Inert feed material is collected in a so-called lead concentrate of metallurgical origin, the primary slag, which is sold. It is rather a valuable feed material for further processing than a slag The off-gas is cooled in a flux-flow system, entering then an electrostatic dust precipitator. Having passed a further washing and cooling system, SO2 is oxidized and collected and sold as concentrated sulphuric acid. The presentation will cover a review of the start-up phase, the development of significant production parameters over the last years and actual production routes and figures. A comparison of environmental data between new and old applied technology is made.

Jan 1, 2006