Search Documents

By Xiao Hong, Zhang Wenqiang, Gao Bing

The characteristics of top charging coke (coke 1) and stamp charging coke (coke2) were investigated. The weight loss ratios of two kinds of cokes with and without alkalis were measured after reacting with CO under the temperature of 2 900, 1000, 1100 and 1200 °C respectively. The microstructures of original cokes were observed by SEM. The experiment results show that, with no addition of alkali, the weight loss ratios of coke 1 and coke 2 were nearly the same under the temperature of 900 and 1000 °C. While the weight loss ratio of coke 2 was much larger than coke 1 under the temperature of 1200 °C. With alkali-rich, the weight loss ratio of the two cokes was almost the same at 1100–1200 °C.

Mar 1, 2017

By Esperidiana A. B. Moura, Elizabeth Carvalho L. Cardoso, Glauson Aparecido F. Machado, René R. Oliveira

Plastics global annual production exceeds 250 million tons and more than 40% of the total plastic production is used as packaging materials. In recent years polymeric materials derived from biomass have received great attention due to scarce petroleum resources and environmental concerns. PLA is one of the most extensively studied bio-based and bio-compostable aliphatic polyesters; nevertheless, high brittleness and low toughness limits its application. Blending PLA with PBAT (Poly(butylene adipate-co-terephthalate)), an aliphatic-aromatic copolyester, was the solution found due to its high toughness and biodegradability. Differences between PLA and PBAT solubility parameter values lead to the formation of immiscible blends as well as reduction in their mechanical performance besides a poor morphology; so, 5% of pre-irradiated PLA and a previous compatibilized PLA/PBAT (EcovioTM) were added to PLA/PBAT blends in order to improve miscibility phases. Investigations were accomplished on phase morphology (SEM), mechanical properties, thermal behavior and X-ray diffractions (XRD).

Mar 1, 2017

By J. R. Wynnyckyj, R. Marr

Continuous measurement based on radiation pyrometry has often met with difficulties whose causes have been obscure. In this paper the experience gained with on-line pyrometry in utility and Kraft recovery boilers in the range 800-l400oC will be reported. It is shown that the inherent problems are best resolved by using a spectral pyrometer not sensitive to gas radiation. The radiation from the suspended particles thus provides the signal. It is further shown that the principle cause of difficulties is signal calibration drift caused by heat fluxes originating from surrounding surfaces and reflected by the particles to the pyrometer. Several examples are given how such problems may be resolved using process information and/or additional measurements, fed to and processed by and on-line microcomputer.

Jan 1, 1989

By Katsukiyo Marukawa, Mashamichi Sano, Shigeta Hara

"Various subject of studies are discussed to develop ·innovative refining processes in the 21st century for cost reduction, production of high quality steel and environmental conservation. The future refining reactor should have abilities of highly efficient mixing and separation of different phases. It is stressed ·that applications of electromagnetic and ultrasound energies, and control of flow fields rate required to create the highly efficient mixing I separation reactor.IntroductionIn recent years, it seems that the research and development in the field of steelmaking has shifted its emphasis to the solidification I ingot-making process in which continuous casting plays the leading role. From a long-range point of view, however, the need for continual development of the refining process will probably increase but is very unlikely to decrease. In order to meet such demands, it is required that problems and issues of the present process should be clearly grasped and that there must be rapid progress in process elements, such as highly efficient mixing and separation of different phases.Applications of electromagnetic and ultrasound energies and flow field control will become important options for resolving the above-mentioned problems. By efficiently and skillfully incorporating these new technologies into high-efficiency mixing/separation reactors, the innovative refining process will be established in the early 21st century."

Jan 1, 2000

By Juliana G. Gutierrez-Paredes, Gabriel Plascencia-Barrera, Fidel Reyes-Carmona

In Mexico, many tonnes of nickel from waste petrochemical catalysts are dumped every year. In order to recover all that nickel, a hydrometallurgical reactor was designed. This design was performed in a systematical fashion, which included the chemistry of the system under study, both a kinetic and mass transfer study, and finally the use of the RID function, to optimize the reactor size. It was found that the NiO leaching with sulfuric acid is well represented by a first order reaction. The mass transfer results are in good agreement with the experimental results, obtaining over 95% nickel extraction in both cases. A marketing study was also completed that determined that it is possible to make a good profit by processing this residue provided the capital cost was low.

Jan 1, 2000

By Coida D. S. Renata, Gerald Okwuchi Onyedika, Moura E. B. Esperidiana, Graca Valenzuela-Diaz, Martin Chidozie Ogwuegbu, Francisco R. Valenzuela-Diaz, Amauche Cyprian Achusim-Udenko

This work aims to incorporate Mgbee clay, vegetal fibre (Costus afer) in recycled low density polyethylene (rLDPE). The incorporation of clay and vegetal fibre in rLDPE was carried out using a twin screw extruder machine and the nanocomposites were obtained. The nano composites were characterized by the Young’s modules test, tensile tests, bending test, XRD, SEM, DSC, and TG and other properties evaluated. The results of morphological and thermal properties showed a good interaction between the clay, and rLDPE as compared to neat rLDPE.

Mar 1, 2017

By John A. Clark, Danylo Oryshchyn, Casey Carney, Stephen Gerdemann, Cathy Summers, Thomas Ochs

"Limited analysis of combustion gas streams where carbon capture is not of interest is done mainly to ascertain operation parameters. Stringent regulations on acid gases and particulates promote careful flue gas analysis. Unregulated components are typically not analyzed. Typically not more than four points (two in the boiler, and one each in the flue and the stack) are sampled. A successful oxy-fuel process with carbon capture and compression is anticipated to require as many as 12 sample points with analysis for water, nitrogen, oxygen, argon, NOx, SOx, and carbon monoxide. Carbon dioxide captured for beverages produces a high value product and the cost associated with analysis is warranted. However, carbon capture for disposal must keep all costs to a minimum. This paper will compare alternative approaches for cost-effective sampling and analysis of the carbon dioxide product streams from oxy-fuel combustion, through all stages of production through compression and pipeline/vessel delivery.IntroductionAnalysis of gases in an oxy-combustion process with carbon capture is essential to the operations of the oxy-fired boiler and the subsequent collection, compression, and purification of carbon dioxide. The process is charged with pure oxygen and not-so-pure carbon in the form of coal at the front end, generating a product of mainly carbon dioxide with traces of argon, nitrogen, sulfur compounds, nitrogen compounds, oxygen, hydrogen, and mercury. It is possible that hydrogen chloride and hydrogen sulfide may also be present in trace amounts [1]. The trace components primarily come from impurities contained in coal such as water, sulfur, nitrogen, and volatile organic compounds. Coal also contains a good deal of mineral matter that is transformed into ash during combustion, becoming particulates that can complicate the analysis regimes utilizing standard analytical equipment."

Jan 1, 2010

By M. -V. Wang

Hydrotreating and hydrorefining (HT and HDS) spent catalysts contain molybdenum, vanadium, nickel or cobalt at concentration levels that can make metals recovery economically viable. Quanzhou Jing-Tai of China has developed, through many years of operating experience in metal recovery from spent catalysts, a simple process for recovery of these metals and the production of environmentally benign residues. The process first subjects the catalysts to a low-temperature calcination step, followed by grinding of the calcine. The ground material is then leached with 10-20% v/v hydrogen peroxide to recover metals such as Mo, V and Ni or Co. This step has a selectivity that is greater than 95% for the metals. The undissovled residue, which contains mainly Ah03 and Si02, can be dewaterd and used in the production of masonry bricks. The pH of the rich liquor is then adjusted to between 0.5 and 2.5 by adding dilute sulfuric acid to co-precipitate Mo and V, with a recovery rate of greater than 99%. The lean liquor contains mostly dissolved Ni or Co, which can be recovered through precipitation at a pH of between 8.5 and 9.5 by caustic additions. The final liquor is then sent to an ion exchange step for final recovery and cleanup of residual metals. The effluent is then discharged after a simple wastewater treatment process, which has been found to meet all environmental requirements. The entire process has been found to be simple, cost-effective with minimal environmental impacts while achieving the goal of complete resource recovery from spent catalysts commercially.

Jan 1, 2000

By Anjali Talekar

Low temperature heat capacities of pentaerythritol [PE: C(CH2OH)4], pentaglycerine [PG: (CH3)C(CH2OH)3], and 2-amino-2-methyl-1,3-propanediol [AMPL: (NH2)(CH3)C(CH2OH)2]have been determined by adiabatic calorimetry from 3 K to 300 K. To the best of our knowledge, this is the first reported heat capacity measurement below 280 K for PE and AMPL. The Debye temperatures for these organic crystals have also been determined and compared with other alcohol derivatives of neopentane.

Jan 1, 2006

By Huimin Lu, Liyuan Zhao, Zhijiang Gao

The aluminum matrix composite reinforced by graphene was successfully fabricated using high pressure torsion (HPT). With only 0.5wt% graphene, the grain size was reduced to 100nm while that of pure Al was about 500nm. The hardness of the composite increased from the center (64HV) to the edge (120HV) of the sample. Moreover, the tensile strength of this composite reached 197MPa, while that of pure Al was 157MPa. The enhancement in mechanical properties was induced by grain refinement, load transfer from the matrix to the reinforcement and dislocations piled up at the grain boundaries.

Jan 1, 2015

By Adam Powell, David Dussault

"Electric Field-Enhanced Smelting and Refining is a process for driving the reaction between carbon in hot metal and iron oxide in slag, for example, in a steelmaking reactor. This process involves inserting electrodes into the slag and metal phases, such that the overall reaction FeO + C -> Fe + CO is separated into two half-cell reactions: Fe2+ + 2e· -> Fe at the cathode in the slag, and C + O 2 • -> CO + 2e· at the anodic slag-metal interface. Without the electrodes, the reaction is very slow, but with electrodes, the additional surface area available to the ferrous ions for reduction accelerates the reaction even without any applied bias. When a bias is applied to the electrodes, the electric field across the slag further accelerates the overall reaction.With or without applied bias, the process is first-order in the ferrous ion concentration, and limited by ferrous ion transport to the cathode. To complicate matters, as the liquid iron is reduced at the cathode, the Mullins-Sekerka instability leads to formation of dendrite-like liquid iron fingers which grow into the slag. Because of this, the design of the cathode can have a significant effect on the overall process kinetics, and understanding of the dynamics of these fingers and of their effect on mass transfer is necessary for the intelligent design of the overall process and the cathode in particular.Toward this end, a detailed mesoscopic two-phase slag-metal model is presented here which describes multi component diffusion in the slag and fluid flow in both phases in the vicinity of the cathode. Diffusion in the slag is driven by chemical and electrical potentials. The phase boundary is modeled as a diffuse interface using a phase field approach. Because this electrochemical reaction occurs at high-temperature, the kinetics of charge transfer and adsorption through the double layer are fast relative to transport, permitting the use of simple linear reaction kinetics. This also eliminates the need to discretize the double layer, with the result that charge neutrality may be assumed everywhere in the domain. Introducing electric field dependence of the gradient potential and well height coefficients in the free energy function allows the model to capture electrocapillarity at the interface."

Jan 1, 2001

By Hongxu Li, Zhaobo Liu, Zihan Zhao

A completely new process of selectively recovering Sc3+ without impurity of Fe3+ from Bayer red mud was developed. Prior to water leaching process, red mud needs to be digested and sulfated at a low temperature and subsequently roasted at a higher temperature for a period of time. During the roasting process, the products such as SO2, SO3 and H2SO4 molecules of thermal decomposition of sulfites including NaFe(SO4)2 and NaAl(SO4)2 could be recycled and reused as the raw materials of sulphuric acid. The leaching results indicate that roasting temperature and roasting time are the main constraint on selective leaching performance of scandium. As the sulfated red mud sample is roasted at 750 degrees C for 40 min and subjected to water leaching at 50 degrees C for 30 min, 53.0 wt% Sc3+, <1.0 wt% Fe3+, <0.3 wt% Si4+ and ~8.9 wt% Al3+ could be leaching out. Of note, the solid-liquid separation process is quite easy to be carried out.

Mar 1, 2017

By Wenjun Duan, Zhimei Wang, Tianwei Wu, Qingbo Yu

In order to recover the waste heat of molten blast furnace slag, a reactor with top-submerged lance was established. The numerical simulation and experiment study of the flow characteristic in the reactor were conducted. The mathematical model of reactor was established and the Euler-Euler model was employed to simulate the gas-liquid flow in molten slag bath. Meanwhile, the experiment results were obtained and compared with the simulation to testify the accuracy of the established model. According to the bubble behavior in bath, there were four stages: initial expansion stage, bubble detachment stage, freedom lift up stage and bubble broken stage. When the flow field in bath fully developed, the gas fraction decreased with the increasing of bath depth. During injection process, the area near the nozzle and lower the bath would first generate two symmetric heliciform flow regime, and then the flow regime in whole bath would become irregular because of bubble lifting up and rupturing. The gas fraction in bath, the average velocity and turbulence energy of slag would decrease before it increased to maximum and then it would keep fluctuate in a range.

Mar 1, 2018

By Samson Adeosun, Sanmbo Balogun, David Esezobor

"Iron and steel making processes give rise to large amounts of usable and unusable materials, the latter generally being termed wastes. It is sometimes difficult to distinguish between re-usable by-products and wastes which cannot be sold or land-filled. Much depends on circumstances such as the local market for the material. This can itself vary from time to time with by-products which cannot be used or sold becoming wastes and vice versa. This paper defines the concept of “waste-free technology”, discusses its development in the steel industry and highlights the benefits of the technology to the manufacturing sector and the environment. The paper also articulates how the “waste-free” technology could be applied in the proposed Ajaokuta integrated steel plant in Nigeria.IntroductionIn the past, nature was considered an inexhaustible store. Its resources were consequently exploited and waste products therefrom were discarded. Today, attitudes have not changed appreciably even as raw materials cost rise by the year to pose a series of socio-economic problems, which, among others, may include the rational and optimum utilization of resources, environmental protection and reduction of waste formation. Consequently, industrialists now face unexpected regulatory pressure in areas of pollution prevention, waste minimization and hazardous waste disposal.Iron and steel making processes give rise to significant amounts of usable and un-usable materials, the latter generally being termed waste. It is sometimes difficult to distinguish between re-usable by-products and wastes which cannot be sold or land-filled. Much depends on circumstances such as the local market for the material. This can itself vary from time to time with by-products which cannot be used or sold becoming wastes and vice versa. In this paper, the term waste refers to those materials that are either irrationally utilized or, land-filled and part of the byproducts that are not utilized. It includes that part of used materials which is not incorporated into the products manufactured during a process stage and which in contrast to reuseable materials, is considered not suitable for any further use, owing to technical or economic factors. In general, these materials are inorganic and parts of them are either utilized or passed to the other processes; the other part should be disposed of using well-established waste disposal practices to avoid any environmental threat.Thus, creative methods must be developed to modify the manufacturing processes to reduce emissions and process wastes by fully utilizing all resources. One method of eliminating the negative effect of waste formation is the use of purification and cleaning structures (pollution control system, PCS). These are, however, quite expensive."

Jan 1, 2008

By Shengli Wu, Binbin Du, Mingyin Kou, Laixin Wang, Kai Gu, Shun Yao, Heng Zhou

Coke plays an important role on the actual blast furnace production (BF), and its quality significantly influences the BF ironmaking process. In this study, the effects of physical properties, chemical composition and high-temperature properties of coke on main technical indexes of blast furnace were investigated. Some coke indexes were defined to evaluate the coke quality. The main technical indexes of BF include production, quality of HM, and fuel consumption. The quantitative relationship between coke quality and main technical indexes of BF were obtained after a series of statistical analysis. What’s more, the effect of these coke quality indexes on blast furnace smelting process was also explored, and all the relationships obtained from the analysis will provide a theoretical basis for the appropriate use of coke in blast furnace. The most reasonable range of coke quality indexes can be determined combining with the actual production as well.

Mar 1, 2018

By Tuula Mäkinen

One of the latest applications of the Outokumpu Flash Smelting Technology is the direct smelting ,of nickel concentrates to metallised low-iron nickel mattes. Compared to the conventional nickel smelting, the new DON process needs a lower number of smelting vessels resulting in considerable economic and environmental benefits. Fundamentals of smelting nickel concentrates in one stage to low-iron mattes are presented. Properties of nickel. smelting slags with an emphasis of the slag fluidity at high MgO-levels are also discussed. Conditions prevailing in DON mattes at high oxidation degrees are presented as well as their influence on the behaviour of such mattes in the settler and on tapping the furnace. Distributions of elements in the direct smelting are presented and compared with the conventional process. A further comparison is made with pilot-plant data and the industrial scale.

Jan 1, 1998

By E. Allain

Extraction of basic metals from sulfides by conventional pyrometallurgical processing leads to the emission of SO2. To avoid this inconvenient, low temperature selective chlorination of sulfide concentrates could be an alternative. However, such process generates hazardous chlorides SxCly. A part of sulfur chlorides such as SCI2 can be recycled as a chlorinating agent of metal sulfides. Hydrolysis of sulfur chlorides, using a solution containing Na2S.9H2O, led to the recovery of more than 90 pct of elemental sulfur. Reduction of SxCly by hydrogen was investigated between 300 °C and 800 °C. About 70 and 90 pct of elemental sulfur were recovered from SC12 and S2C12, respectively. A flow sheet for the chlorination of metal sulfides and the treatment of sulfur chlorides was suggested.

Jan 1, 1998

By Jose R. Parga

In mining operations, cyanidation is the ,predominant method by which gold and silver are recovered from their ores and it is recognized that cyanide consumption can be a major factor that contributes to the operating costs for such operations. Also after extraction and recovery of precious metals a certain amount of cyanide is delivered to the tailings pond and must be considered with respect is environmental problems due to the toxicity of cyanides. In this regard, the Air-Sparged Hydrocyclone (ASH) has been used as a reactor for the treatment of cyanide solutions in two ways; first for cyanide recovery by acidulation using the Mexican modification of the Mills-Crowe process and second for cyanide destruction by oxidation with the use of chlorine dioxide (ClO2). In both cases, excellent performance can be achieved using the high capacity ASH system.

Jan 1, 1998

By Fabiola Alvarez, Ana E. Bote, Daniel Pasquevich

"The oxidation of aluminum and its alloys was extensively studied for improving the corrosion resistance in structural materials having high specific strengths. But this reaction involves the formation of a very thin barrier layer on the metallic pieces. Furthermore, the ·recent development of the directed melt oxidation process for producing metal-ceramic; composites has renewed the interest in the study of interaction between gases and metals. Oxidation experiments in the presence of different chlorine partial pressures and at different temperatures were performed in ·a thermogravimetric balance, and microstructures were analyzed by electronic microscopy and X-ray diffraction. The oxy-chlorination kinetics was determined and the oxide formed W(IS amorphous at temperatures below 600 °C and crystalline .at higher temperatures. The appropriate experimental conditions for the fastest completed oxidation was further determined.IntroductionThe use of fine powders for the manufacture of ceramic components has significant advantages. They include excellent sinterability; low sintering temperature and better microstructure leading to improved mechanical properties. The conventional method of producing fine oxide powders involves controlled precipitation and pirolysis of suitable salts. The main limitation of the high temperature decomposition route is the evolution of environmentally unacceptable and corrosive gases. Controlled precipitation of hydroxides from solutions of salts, followed by thermal treatment involves large volumes of solutions and the calcination step that can induce grain growth (1).Direct oxidation of aluminum metal for producing alumina powder requires high temperatures for the direct oxidation of molten Al alloys by a vapor phase oxidant process (2, 3) or high technological process like thermal plasma reactor ( 4).Oxidation of high purity aluminum (5, 6) below the melting temperature· is initially characterized by a nearly linear reaction rate, followed by a rate which decreases rapidly with further weight gain. However, the oxidation rate of an aluminummagnesium alloy is much faster and it does not conform to any common oxidation law, but it is nearly parabolic at temperatures between 200 and 400 °C, an nearly linear· above 400 °C."

Jan 1, 2000

By Shen Shen, Paul R. Ohodnicki, Samuel J. Kemion, Vladimir Keylin, Alex Leary, Joseph F. Huth, Michael E. McHenry

"Recent DOE workshops highlight the need for advanced soft magnetic materials leveraged in novel designs of power electronic components and systems for power conditioning and grid integration. Dramatic weight and size reductions are possible in these applications through operating at increased frequencies. This manuscript discusses processing and composition design approaches for optimizing FeCo-based nanocomposites for higher frequency operation at 100 kHz and above. The proposed strategy involves starting with prior compositions known to exhibit high inductions, optimal field crystallization induced anisotropy, and excellent mechanical and high temperature magnetic properties. Proposed alloy modifications for the applications of interest would include increased amorphous phase resistance, optimum induced anisotropy, and minimized or carefully engineered magnetostriction. Relevant process developments would target reduction of ribbon thickness by optimizing the casting process or post-processing treatments such as chemical thinning or rolling. Three archetypes FeCo-based nanocomposites are described including near equiatomic FeCo-based, Fe-rich and Co-rich alloys.MotivationSilicon steels are widely applied for 60Hz utility-scale transformers [1]. For applications at high frequencies, however, Si-steels exhibit unacceptable losses and ferrites are typically used due to their high electrical resistivity and good soft magnetic properties [2]. However, the low inductions offerrites have limited their applications in power electronics. Developments in rapid solidification have led to amorphous metal alloys and controlled nanocrystallization processing has resulted in state-of-the-art amorphous/nanocrystalline nanocomposite soft magnets [3-5]. Commercial utility-scale transformers made with Fe-based amorphous materials have been demonstrated to result in significant energy savings with an associated reduction in greenhouse gas emissions [6]. DOE workshops held in 2010 emphasized a need for advanced soft magnetic materials for the next generation of power electronics. For advanced power conditioning and grid integration applications, frequencies of 20 kHz up to -1 MHz are of interest depending on the power level [7]. Here, we review previous work and discuss the approaches to optimize FeCo-based nanocomposite materials for high frequency applications."

Jan 1, 2012