Search Documents

By Petr Dvorak, Jana Selucka, Hong Vu, Petra Starkova, Tomas Frydl

Waste, generated during high pressure leaching of lateritic nickel ores, contains about 50% of iron in form of magnetite but high chromium content ( *3%) does not allow its extensive utilization as the raw material for pig iron production in blast furnace. The chromium removal from the waste was carried out by two methods: (1) oxidative alkali roasting with NaOH and/or Na2CO3, followed by water leaching and (2) oxidative leaching in KOH sub-molten salts solutions. The results show that about 90.1% of Cr was removed when the waste was roasted at 900 °C for 3 h with 33.1 wt% of NaOH. The removal of 88.2% of Cr was achieved if the waste was roasted at 900 °C for 3 h with 40 wt% of Na2CO3. The sodium content in the water-leached residues was reduced from 5% to about 0.5% by reaction with CaO in aqueous solutions at 80 °C for 2 h. About 70% of Cr was removed if the waste was leached at 190 °C in 73 wt% KOH for 8 h.

Mar 1, 2017

By A. Warczok

The heat transfer coefficient between liquid slags and solid surfaces is important for the design and operation of metallurgical reactors. An experimental technique developed for the purpose of measuring the heat transfer coefficient between liquid slags and solid metals is described. During the initial heating up of a Ni cylinder upon immersion in a liquid slag, a layer of frozen slag initially forms, then melts. The heat transfer coefficient measured during the initial rapid heat-up of the Ni cylinder, is approximately twice as high as the heat transfer coefficient measured during the final heat-up of the Ni cylinder subsequent of the liquidus temperature of the slag. The technique was tested in various melts i) NaNO3, ii) NaCl, iii) Na3AlF6 and iv) 2FeO*SiO2, giving consistent results. It was found that the heat transfer coefficient increases with increasing bath superheat and stirring. The heat transfer coefficient during the heating up following complete remelting of the frozen slag, is related to the slag superheat(AT) and the specific stirring energy(W) per kg of slag(E) as follows.

Jan 1, 1993

By Shiju Zhang, Yongnian Dai, Songli Liu, Wenhui Ma

The BaZrO3 and CaO-doped BaZrO3 ceramics were fabricated at 1750 °C for melting the Ti2Ni alloys, respectively. Employing XRD, OM and SEM, the influence of CaO on the composition of BaZrO3 and the interaction between the BaZrO3 ceramic and titanium alloy was investigated. The results showed that the CaO doped BaZrO3 was consisted of CaO and Ba 1−xCaxZrO3. The grain on the surface of BaZrO3 ceramic was loose after melting, and the thermodynamic analysis indicated that the dissolution-erosion was responsible for the interaction mechanism. An amount of BaZrO 3 refractory was attached to the Ti2Ni alloy bottom after the alloy was cooled. However, no refractory was found on the bottom of Ti2Ni alloy, which was cooled down on the CaO doped BaZrO3 ceramic. CaO additive can effectively reduce the interaction between the BaZrO3 refractory and the titanium melt, indicating that it was a very promising refractory for preparing the titanium alloy.

Mar 1, 2018

By A. A. Hejja

"Liquidus temperature and electrical conductivity data measured on synthetic slags were modelled by the use of neural nets (NN). In this work the applied multilayer feedforward NNs were trained by a conjugate-gradient optimisation for which a three layer formulation was used. Very good fits were obtained for both the liquidus temperature and the conductivity data. The synthetic slags were prepared from pure oxides to represent a wide range of compositions likely to be encountered in ferromanganese and silicomanganese smelting. The slag constituents were in the following range: Mn0;5-30%, Ca0;20-35%, Mg0;5-15%, Si02;27-58%, Al20 3;5%. Liquidus temperatures varied from 1300° to 1380° and increased with increasing basicity ratio. The electrical resistivity of slags decreased with the increase of basicity ratio from 0.55 to 1.1 but above 1.1 basicity ratio the resistivity tended to increase depending upon the MnO content.Neural NetsVarious neural net (NN) topologies such as Hopfied nets, Hamming nets, Carpenter/Grossberg classifiers have been discussed in some detail by Lipmann (1). In this work, the applied multilayer feedforward NNs are not trained by backpropagation (BP) using the generalized delta rule (2) (GDR), but by a conjugate-gradient optimisation [3,4] - a procedure similar to that proposed by Barnard and Cole [5]. A neural net is capable ·of learning the non-linear functional relationship existing between a set of inputs and outputs [ 6]. In this capacity a neural net is used to determine the functional relationship that exists . between N dependent and independent variables, which characterize the system under consideration For a three layer neural net [1] the following function may be formulated, which relates X; inputs to the output Y 0 from node o:"

Jan 1, 1997

By I. D. Reznik

On blowing nickel matte in a converter without quartz, first the oxidation of metallic iron and a part of FeS occurs without evolving sulfur dioxide, the formed FeO dissolves in a sulphide smelt and form a homogeneous oxysulphide smelt. On further increasing the FeO content, the oxysulphide separates into 2 layers. Based on the laboratory investigation of FeO-(FeS+Fe°) - (Ni3S2+Ni°) ternary phase diagram we have identified the separation region at 1250°C. The boundaries of the separation region have the form of an arc and the composition of the separated oxysulphide layers is defined by the canodes. In the nickel or copper-nickel matte - silicacalcium oxide slag system at 1250°C three layers, namely sulphide, oxysulphide, and slag may be formed. A high slag basicity due to the presence of CaO can serve to enhance the activity of FeO; a low nickel content in the matte corresponds to a high concentration of FeS therein; FeO from slag and FeS from the matte form a homogeneous FeO-FeS solution, i.e. an oxysulphide layer. The investigation on the "Camebaks" apparatus and by the nuclear gamma-ray resonance spectroscopy method of the phase composition in a slowly cooled oxysulphide layer has shown the presence of four phases: wustite, troilite, ferronickel grains, and calcium oxide-silica inclusions. Knowledge of regularities in the oxysulphides formation makes it possible to use them in pyrometallurgy of nickel and cobalt or preventing their formation.

Jan 1, 1997

By Åke Saudström

An EAF dust sample generated in a scrap based steel mill was treated by a combination of hydro- and pyrometallurgial techniques. The EAF dust contained mainly ferritic spinels forming solid solution phases according to the general chemical formula (MnxZnyFe1-x-y)Fe2O4 and other oxide phases such as ZuO. CaO and Ca2Fe2O5. The EAF dust was first treated by hydrochloric acid leaching at p8=3 which dissolved 63% of the zinc. The pyrometallurgical treatment of the leaching residue was studied using an induction heating system to simulate some important operations of EAF smelting of the residue in combination with steelmaking. The leaching residue was mixed with carbon powder to obtain a mixture with 52.1% ZnFe2O4 and 175% carbon. The mixture, scrap, and slag former were charged together in a crucible and heated to attain a melt temperature around 1650°C. The effects of different amounts of mixture on the zinc balance and iron recovery were examined. Based on the test results, suggestions are made for the EAF recycling procedure of the leaching residue.

Jan 1, 2003

By Boxun Lu, Juan Wei, Kun Chen, Wanlin Wang, Lejun Zhou

"Slag system is an indispensable part during the continuous casting process, and playing various important roles like absorbing inclusions, modifying heat transfer rate, preventing oxidation of molten steel, etc. to ensure the smooth process and excellent slab quality. However most slags contains more than 8% fluorides which tend to introduce a series of environmental and health problems. This study involves the research of the removal of fluorine through the chemical composition optimization. Through the studies of CCT, DHTT, XRD and SEM, it has been successfully founded that the crystalline phase of Ca11Si4B2O22 discovered in this study shows very similar crystallization property as Cuspidine (Ca4Si2O7F2), which is the most important crystalline phase in the current fluorine bearing slags. Moreover, the optimized free/low fluorine slag shows the opportunity to replace conventional high-fluorine mold slag for casting medium carbon steels that is regarded as the bottleneck of green slag development for continuous casting.IntroductionMold flux has been widely used in continuous casting to control heat transfer, lubricate the strand, absorb inclusions, provide insulation and prevent oxidation of the molten steel[1-3]. It usually contains fluorides, like CaF2, NaF etc., which are used to control the viscosity and solidification temperature of mold fluxes [4-5]. However, the presence of fluoride leads to corrosion of equipment, serious environmental pollution (toxic volatiles and water pollution), and high processing cost of cooling water[6-7]. Therefore, the study of low or free fluorine mold flux is of interest and attracts worldwide attention.S. Y. Choi et al. [4] used B2O3 as a substitute for cuspidine in steel B2PB2) however, B2O3 content was extremely high (up to 30 w%). Other studies have investigated F-free mold flux by adding or optimizing components as MgO, Li2O, B2O3 et al[8-11]. However, most of these focused on the melting and viscosity issues or for low or ultra-low carbon steels, where crystallization tendency is not significantly strong. Very few studies regarding to the development of low/free Fluorine mold flux for casting medium carbon (MC) steels have been conducted, due to the difficulty of the crystallization and heat transfer control without the formation of cuspidine."

Jan 1, 2014

By Toshiyuki Kozuka

CdTe metal composite semi-conducting material has high potential in good performance of energy conversion efficiency for solar cell and there is much room for improvement of the performance by developing a process of making a thin CdTe film. In this paper, the imposition of intense magnetic field on CdTe electro-depositing surface is proposed, which is one of the possibilities for improving the energy conversion efficiency. In the experiment, cryogen-free super-conducting magnet up to 5T was used and CdTe film was deposited electrically in -o.nv vs. SHE The electrolyte was Cd and Te ammonia alkali solution with controlled temperature in the acrylic cell of 70mm diameter. Electro-deposition behavior of CdTe has affected by the imposition of the intense magnetic field due to microscopic convection in the vicinity of the depositing surface. Electro-deposited surface of CdTe becomes smooth due to microscopic convection around the surface, and the crystallization behavior is also affected, where crystallization temperature and the grain size is changed by the imposition of intense magnetic field.

Jan 1, 2003

By Sheng-ping He, Zhuo Chen, Qian Wang, Kun-peng Xu

During the continuous casting (CC) process of Ti-Stabilized Stainless Steel, the nozzle clogging or even the crusts composed of TiN, Al2O3, TixOy and the complex inclusions MgOAl2O3, Al2O3 is often occurred. The main objective of the present study is to research the reaction between refining slag or mold flux and Ti-Stabilized Stainless Steel by thermodynamic calculation. A suitable refining slag composition was sought to absorb Al2O3, Tix Oy inclusions, and the reactions between different mold flux and steel was calculated and compared. It was found that a suitable refining slag was difficult to adjust aluminum and titanium to meet requirement simultaneously. The target refined slag is composited of 3–8.7% SiO2, 56–59% CaO, 33–38% Al2O3 and 4% MgO with low melting point and high absorption capacity of inclusions for in the refining of the 321 stainless steel. SiO2, Fe2O3, Na2O and B2O3 of mold flux would react with titanium in the steel. The CaO–SiO2 based mold flux had a strong reactivity than CaO–SiO2–Al2O3 and CaO–Al2O3 based mold flux.

Mar 1, 2017

By Li Zhang

A novel green technology to recovery Titanium compounds from Ti-bearing blast furnace slag under the dynamic oxidation condition was developed and tested. Air was blown into the molten slag as oxygen resource through a lance during the dynamic oxidation process, in which six important results were found: (1) The TiC, (Ti2O3), Fe and (FeO) in the slag were oxidized; (2) The temperature of slag temperature rapidly increased; (3) The viscosity of slag decreased; (4) The coalescence, growth and drop of the metallic Fe droplets in the molten slag were carried out under an air agitation condition; (5) The dispersed Ti components were selectively enriched into the perovslite phase, and the perovskite phase could be selectively precipitate and grow. And also, the perovskite phase can be separated by the dressing method. The oxidation of molten slag gives off a large amount of heat, which helps chemical reactions proceed, improve the rate of chemical reactions, and promote the precipitation and growth of the perovskite phase. The features of the technique are clean, low cost and a great capacity to deal with a large quantity of slag. It was confirmed by experiments that the precipitation of the perovskite (CaTiO3) in molten slag is obviously affected by operation factors such as temperature, chemical composition, heat-treatment, additives and so on. The precipitating kinetics and mechanism of the perovskite phase from molten slag during the dynamic oxidation processes were also investigated.

Jan 1, 2006

By H. Y. Sohn, M. Y. Mohassab-Ahmed

"As part of research to develop a novel flash ironmaking process using reduction of iron ore concentrate by natural gas or hydrogen, sulfur and phosphorus distribution ratios between MgOsaturated slag and iron were determined in the temperature range 1550-1650°C under three different gas atmospheres: H2/H2O, H2/H2O/CO/CO2, and CO/CO2. The distribution coefficients of sulfur (Ls) were 4.0, 2.0, and 0.8, respectively, under these atmospheres. The distribution coefficients of phosphorus (Lp) were, respectively, 8, 17, and 20 under these atmospheres. In the flash process over -25 wt% P and S volatilize during ore concentrate downward flight in the reactor shaft in addition to avoiding coke. Therefore, iron produced by the flash ironmaking process would have much lower sulfur contents than the typical hot metal produced by the BF.IntroductionGiven the issues related to large carbon dioxide emissions and energy consumption in the existing ironmaking technologies, a novel flash ironmaking technology was conceived by Sohn [1-3] at the University of Utah. This technology is the first ironmaking process that will convert iron ore concentrate directly to metallic iron in-flight. This process will produce iron directly from concentrate without requiring pelletization or sintering and avoid the need for coke. In addition, this process concept takes full advantage of the fine particle size of concentrate with a large surface area, which permits rapid reduction by a gas. In this novel ironmaking process, potential reductants and fuels are H2, natural gas, and coal gas. Therefore, an iron-slag bath is expected to be at equilibrium with gas atmospheres of mainly H2/H2O or CO/CO2/H2/H2O, respectively, corresponding to the use of H2 or natural gas/coal gas. Since the effects of an H2O- containing atmosphere on slag properties have not been studied before, it is critical for the development of the novel flash process to determine these effects. In H2-H2O-CO-CO2 gas mixtures under ironmaking conditions, H20 was found to have the most pronounced effect on the slag chemistry [ 4, 5]. In addition, it was found in this laboratory that water in the gas atmosphere affected the distribution of Mn between slag and molten iron [6]. Most previous work used CO/CO2 gas mixture to control oxygen partial pressure (p02) [7, 8]. Others used only inert atmospheres [9], although Kor and Richardson [10] used a mixture of C02/H2 to control p02. For phosphorus, previous research focused on Ar [11], Ar-CO mixture [12], CO [13], CO/CO2 [14] or N2/CO [15]. Therefore, it was necessary to investigate the effect of water vapor content in H2-H2O-CO-CO2 mixtures on the equilibrium distribution of sulfur and phosphorus between CaO-MgOsatSiO2-Al2O3-FeO- MnO (0.2-0.8 wt%)-P2O5 (0.1-0.9 wt%) slag and molten iron as part of the development of the novel flash ironmaking technology."

Jan 1, 2014

By Y. K. Rao

Relatively pure crystalline lead sulfate (PbSO4) can be produced by chemical vapor transport from an impure source such as the lead-acid battery paste or the roast-ore-leach-residue from a hy¬drometallurgical process-route. In a closed-reactor, transport of matter is induced by a tempera¬ture-gradient and the steady-state transfer rate can be calculated using the data on the standard free energies of formation for the species present and the pertinent binary diffusion coefficients. The present work focusses on chemical vapor transport in a tubular reactor (1.4-cm inner diameter x 10-cm long) with the source- and deposition-ends held at 850°C (T,) and 750°C (Td), respectively; PbC12(g) is the 'solvent' or 'transport agent' and NiSO4(s) placed in the source-zone -serves to maintain a sufficiently high S0,-potential such that the stability of the lead sulfate species is ensured. For the purposes of analysis, the gas-phase in the reactor is assumed to consist of eight species: H2O, PbC12, SO3, SO2. O2 HO, C12, and PbC14. The reaction between C12(g) and PbSO4(s) in the high-temperature source-zone produces PbCl2, SO2, and 02; four more reaction-equilibria in the same zone yield other species. In the low-temperature deposition-zone, reaction equilibrium involving PbC12, H2O, and SO, leads to the nucleation and growth of PbSO4 crystals; three other reaction-equilibria occur in this zone. By employing the virtual equilibrium state for the end-zones and coupling it to the Stefan-Maxwell diffusion equations for each of the gas species, the respective partial pressures for these, in the source- and deposition-zones, are computed at steady-state. From these data, the molar fluxes of PbCl2. PbCl4, and so forth, are determined. Allowing for the transport-enhancing effects of thermal convection, the net transport rate of lead (or PbSO4) is duly calculated for specified initial conditions. The predicted rates show very good agreement with measured rate data reported in the literature [ V. Plies, T. Kohlmann and R. Gruehn: Z. anorg. allg. Chem, 568, 62 (1989)

Jan 1, 1995

By Chao Lian, Hongxu Li, Hao Bai, Wei Wei

"Application of high-emissivity coating on inner walls in industrial furnaces increases the furnace thermal efficiency. The coating with high emissivity strengthens radiation heat transfer in the furnace, however, according to Wien's displacement law and Planck's radiation law, under heating temperature, the wavelengths of the radiation transfer are mostly between 1-5 µm, implying that increasing emissivity of the coating in near infrared band is more effective for higher thermal efficiency. In this paper, a new CuO-ZnO-based coating material sintered at 1600K was developed. The emissivity of the samples were measured and the result shows that, in near-infrared band, the emissivity of the sample reaches 0.98 at 773K with 13at.% of CuO doped in ZnO. In addition, the effects of CuO doping and use temperature on emissivity were also discussed. Furthermore, crystallization behaviors of ZnO-CuO sintering were investigated by DTA,XRD and SEM-EDS etc., which offered information for possible optimal design of the material.1. IntroductionIndustrial furnaces are widely used in various industrial heating. For example, the metal smelting furnace, ore sintering furnace in metallurgical industry; the distillation furnace, cracking furnace in petroleum industry etc,. The research on efficient energy saving technology has important significance. High emissivity coatings are widely used in many high temperature applications to effectively transfer the heat by radiation [ 1]. The theoretical calculation and experimental studies have shown that, coated high emissivity coating in the heating surface is an effective method to enlarge the infrared radiation power [2].At present, the infrared high emissivity coating has been widely used in China, and have been achieved remarkable energy saving effect. According to Wien' s displacement law and Planck' slaw, most energy of the black body at high temperature is radiated in the wavelength range of l-5µm; however it happens that many materials have the low emissivity within this range. Thus, it is important to improve the near-infrared band emissivity of materials [3]."

Jan 1, 2013

By Run-boWang, Fan-yi Meng, Jian-Liang Zhang, ZheWang

To elucidate the influence of high Al2O3 content on sinter softening and melting behavior, heating-up reduction test under load was carried out. In addition, microstructure study of sinter bed structure change at a different temperature was also made and the mechanism that the effect of Al2O3 content on sinter softening and melting property was discovered. SEM results showed that the increase of Al2O3 content favored the formation of Al2O3-rich slag phase, such as the eutectic (2CaO·SiO2-2CaO·Al2O3·SiO2-FeO) and gehlenite (2CaO·Al2O3·SiO2), resulting in the decrease of sinter Ts temperature. Further, high Al2O3 content improved the concentration of metallic iron and lowered the dripping temperature due to the decrease of slag liquidus temperature and viscosity. At a fixed basicity, it was indicated that there was a relationship between Al2O3 content and sinter softening-melting property. Based on the results, counter strategies to cope with the adverse effect of high Al2O3 content on the cohesive zone property were also proposed. It could provide guidance for the blast furnace operation of sinter with high Al2O3 content.

Jan 1, 2015

By Jun Lu, Min Chen, Wei-jian Su, Jian-zhong Luo, Yu-tao Lei

"In the case of treating phosphatizing wastewater containing zinc, zinc had an impact on the solution chemistry, especially on pH. Fe2(SO4)3 and CaCl2 were used as precipitators to remove phosphate from zincic phosphatizing wastewater and the optimum pH was investigated. Zinc ion had a significant effect on the optimum pH. The optimum pH ranges were 12.10(inlet concentration of 15.67mg/L, outlet concentration of 9.53mg/L), 3.04-5.50(inlet concentration of 11.97mg/L, outlet concentration of 0.44-0.26mg/L), and more than 10.72(inlet concentration of 12.24mg/L, outlet concentration of less than 0.47mg/L) under the conditions without precipitator, with Fe2(SO4)3 and with CaCl2 respectively.Introduction Phosphate coating is commonly used for protective coating of machine elements. Including oil removal by caustic washing, rust removal by acid washing, phosphatization and inactivation, the phosphatization process produces wastewater containing inorganic salt of high concentration, especially the phosphate, beyond the environmental standards and polluting environment seriously. What’s more, the wastewater from zincic phosphatizing technology also contains another pollutant, zinc. At present, Chemical Precipitation (CP) and Biological Nutrient Removal (BNR) are two of most common technologies of phosphate removal. BNR, such as A/O, A2/O and UCT technology, is suited for wastewater containing organ phosphorus of low concentration and CP for wastewater with phosphate of high concentration [1]. Researches on CP treating wastewater containing phosphate of high concentration, mainly focus on adding quantity of precipitators[2-5] and coagulants[2-4] and the choice of technologies[3-9]."

Jan 1, 2008

By Tetsuya Uda, Sakae Shirayama

"With the aim of producing nickel (Ni) metal directly from acidic aqueous solution containing cobalt (Co) and other impurities, selective reduction of Ni was examined. As a preliminary experiment, sodium hypophosphite monohydrate (NaH2PO2·H2O) was selected as a reductant, and reacted with aqueous solution containing 0.1 mol L-1 nickel sulfate (NiSO4·6H2O) and 0 ~ 0.05 mol L-1 cobalt sulfate (CoSO4·7H2O) for 3 hours at 90 °C. As a result, it was revealed that Ni was selectively reduced and separated from Co in the acidic region (pH= 4.8). In this study, differences of reduction behavior between Ni and Co were investigated, and the feasibility of Ni I Co separation by the selective reduction of Ni was discussed.IntroductionEfficient Ni condensation and separation from Co are essential in nickel hydrometallurgical processes. Currently, the hydrometallurgical production of Ni from oxide ore is mainly carried out by acid leaching at elevated temperature, followed by the removal of impurities using neutralization, and condensation of Ni and Co into intermediate products such as hydroxides and sulfides. Then, the intermediate product is dissolved in acid aqueous solutions, and Ni I Co separation is conducted by solvent extraction. Finally, Ni and Co are recovered by electro-winning. This complicated process consumes large amounts of alkali, hydrogen sulfide (H2S), and organic solution in a multiple-staged process'. To reduce the consumption of these chemicals, it is important to recover Ni more efficiently from acidic aqueous solution containing impurities."

Jan 1, 2014

By K. S. Raja, M. Misra, S. K. Mohapatra

"Ordered arrays of TiO2 nanotubular photocatalysts were prepared by a simple anodization process. Band gap states of the TiO2 were altered by controlling the anodization electrolyte composition and thermal annealing conditions that resulted in enhanced photo activity. These nanotubes were used for reducing CO2 to methanol either by photochemical or photo electrochemical routes. Pd nano-particle loaded TiO2 nanotubes were employed for photochemical reduction of CO2 to methanol that showed a conversion rate of 12 x 10-3 mol m- 2h-1. Carbon modified TiO2-xCx type nanotubes were used as photo anode and Ti as cathode for photo electrochemical reduction of CO2. The potential of Ti cathode was maintained at -0.5 V SCE. The formation rate of methanol was determined as 13 x 10-3 mol.m-2h-1.1. IntroductionGlobal warming due to emission of carbon dioxide is a serious environmental concern. The atmospheric concentration of CO2 is about 384 ppm by volume and about 3 x 1012 tonnes by weight. Burning of fossil fuels and deforestation are the leading causes for increase in the anthropogenic CO2. More than 32 x 109 tonnes of CO2 are released per year (based on 2006 data) worldwide from the fossil fuel. Pumping CO2 from the fossil fuel power plants into deep ocean basin is one of the most discussed disposal options. The other potential option is converting this green house gas into valuable fuels.Carbon dioxide feed stock can be converted into fuels of solid, liquid or gas phase by chemical, electrolytic, photocatalytic and photo-electrocatalytic methods. Reduction of CO2 to fuel form of any phase requires energy. The reduction process should be energy efficient so that we do not spend more energy and emit more (indirect) CO2 in the process of converting CO2. From this point of view, conversion processes occurring at room temperature look attractive.Electrolytic conversion of CO2 into various forms such as methane1, ethane2, ethylene3, methanol4,5, ethanol6, n-propanol, formic acid7, and formaldehyde has been widely reported. The standard equilibrium potential (at pH: 0) for reduction of CO2 to methanol is 0.14 VSHE and to methane is 0.2 VSHE which is thermodynamically more favorable than hydrogen reduction. However, the gas phase reduction is kinetically complex requiring effective electrocatalyst. The major issues with electrolytic conversion of CO2 to useful products are:"

Jan 1, 2010

By Osamu Yamamoto

In antibacterial evaluation of carbon-ceramic composites, we prepared two type composites with emphasis on carbon-ZnO system; one was porous carbon materials containing ZnO nano-particles and another was porous ZnO coated with carbon thin film. Porous carbon samples containing ZnO at highly dispersed state were prepared by carbonizing the resin exchanged by Zn2+ ion. Porous ZnO coated with carbon thin film was obtained by the pyrolysis of poly (vinyl alcohol). Antibacterial activity of these composites obtained was evaluated by measuring the changes in electrical conductivity with bacteria growth. The antibacterial activity on the composites increased with the increase of t he amount of ZnO in composite and decreased with the increase of carbonization temperature. The antibacterial activity for Staphylococcus aureuswas found to be stronger than that for Escherichia coli. No activity of the carbon samples without ZnO was observed. The occurrence of antibacterial activity was supposed to be due to the generation of hydrogen peroxide from ZnO in composite. In the present work, antibacterial activity of carbon-ZnO composites was studied in the details.

Jan 1, 2006

By Jiang Diao, Yong Qiao, Xuan Liu, Tao Zhang, Bing Xie

The equilibrium experiments between the FeO-SiO2-MnO-TiO2-V2O3-Cr2O3-MgO slag system and solid pure iron were performed to investigate the vanadium and chromium distribution ratio under Ar atmosphere. The influence of w(FeO), w(V2O3) and w(Cr2O3) in slag on vanadium and chromium distribution ratios were studied at 1653 K. The experimental results were compared with calculated distribution ratios based on molecule and ions coexistence theory. Both of them showed that higher FeO content in slag would improve the distribution ratios of V and Cr between slag and hot metal. The distribution ratio of Cr or V increased with the increase of Cr2O3 or V2O3 content, respectively. To optimize the oxidation of V and Cr from hot metal, a high oxidizing slag and suitable content of Cr2O3 and V2O3 in the slag were recommended. The results provided reference for the further study on the extraction of V and Cr in VTi magnetite.

Jan 1, 2016

By A. R. Udupa

The reduction roasting behavior of chalcopyrite has been investigated using various combinations of a desulfurizing agent, i.e., CaO or Na2CO3, and a reductant, i.e., CO, H2 or C. Using these, combinations the sulfur is removed from the mineral as CaS or Na2S rather than SO2 as is the case with conventional copper smelting and converting. The laboratory reduction ex¬periments were conducted using thermogravimetric analysis (TGA) and boat tests of mixed combinations of fine particulate reactants subjected to a continuous gas stream. The degrees of metallization were determined by both weight loss and chemical analysis methods and the products examined using optical and scanning electron microscopy and electron probe microanalysis. The percent reduction after one hour at 900°C ranged from 60% to 94%. From these data It was possible to provide postulations as to the controlling reduction mechanisms.

Jan 1, 1983