Search Documents

By William Petruk

The concentrator of the Iron Ore Company of Canada consists of spiral circuits, a cone plant and a magnetics plant with regrind. The proportions of liberated and unliberated grains of iron oxides at each point throughout the concentrator were measured by image analysis, and recoveries were calculated for each particle type by the MATBAL materials balancing program. The results show that spirals and cones recover more than 92% of the liberated iron oxide grains in the size range of 848 to 150 um,, but the recovery drops off rapidly for finer grained particles. The tailings from the spirals and cones are reground and low intensity magnetic separators are used to recover liberated magnetite in the -37.5 um size range. The concentrator does not have a unit that efficiently recovers iron oxide grains in the size range of 150 to 37.5 um Consequently about 25% of the iron oxides in the ore are lost to tailings as liberated. grains in the size range of 150 to 37.5 um

Jan 1, 1989

By L. A. Harris

In the present study the open gradient magnetic separation' (OGMS) method has been used to beneficiate the -30 + 100 mesh fraction of two high volatile bituminous coals. The evaluation of the effectiveness of the magnetic separation for cleaning these coals is the subject of this paper. Coal petrography in combination with scanning electron microscopy (SEM) and x-ray diffractometry (XRD) were used to characterize the magnetically separated coal fractions. These analyses revealed that the majority of the pyrite and non-pyrite minerals were concentrated in the positive magnetic susceptibility fractions. The bulk of the starting samples (-80 weight percent) were located in the negative magnetic susceptibility fractions and showed significant reductions in pyrite and non-pyritic minerals. The magnetic separation appears to effectively split the samples into relatively clean coal and refuse.

Jan 1, 1981

By S. Moussa

The formation of boron-doped nickel aluminides Ni3AI, (76 at. % Ni) from elemental powders by reaction synthesis using reactive sintering was studied. The process involves the mixing of elemental powders of nickel and aluminium with various wt % of boron up to 1 wt % boron. Nickel and Aluminium powders were mixed in the correct proportion to form the intended boron-doped nickel aluminide intermetallic. XRD, SEMI EDS, Image analysis and Archimedes principle; were used to study the effect of Boron addition on the final microstructure, bulk density, average grain size of as reactively-sintered nickel aluminides (boron-doped), compared with no boron addition. The results showed that at greater boron content than 0.3 wt %, a two-phase non-equilibrium microstructure of consisting of NiAI phase in NiJAI matrix was formed that have been primarily retained even after heat treatment for 5 hours at 1000 °C. Boron was present in solid-solution within both the NiAI and the Ni3AI (in greater amounts) phases.

Jan 1, 2001

By Stephen Chryssoulis, Stamen Dimov

Detection and quantification of precious metals (Au, Pd, Pt, and Rh) in spinels and silicate minerals is important for establishing the maximum attainable recovery by sulphide flotation. To achieve this goal subpart per billion (ppb) detection limits are required plus the ability to quantify results. Existing quantitative microbeam techniques (EPMA, PIXE, SIMS, TOFLIMS) have limits of detection in the O. l-200ppm range. Time-of-flight resonance ionization mass spectrometry (TOF-RIMS) is a microbeam analytical technique that allows for the identification and quantification of atomic species in very small quantities. It utilizes a tunable laser source for resonant excitation and ionization of a particular element of interest and has some unique features: elemental selectivity, linear response over a large dynamic range and very high sensitivity. The analysis consist of three steps: (i) the solid sample is vaporized by laser ablation to form a plume containing neutral atoms, (ii) the neutral atoms of a specific atomic element in the plume are resonantly excited and ionized by another tunable laser, and finally (iii) the ions created are mass analyzed in a time-of-flight mass spectrometer. A TOF-RIMS mass spectrometer was developed at AMTEL for trace element analysis of Au, Pd, and Rh in minerals. The spectrometer was calibrated using homogeneous CANMET and NIST reference samples covering three orders of magnitude in concentration. Attained minimum detection limits (MDL=2cr of the background) are in the low ppb range.

Jan 1, 1999

By Flavio Begazo, William A. Enrico

"Southern Peru Copper Corporation's Ilo Refinery, the largest in Peru, began operations in 1975 with a production capacity of 165,000 stpy. Southern Peru bought the Refinery from the state owned Minero Peru SA on June 1, 1994.The Refinery processes blister from Southern Peru's I/o Smelter. Blister copper is processed in an anode plant equipped with two 365 st tilting reverberatory furnaces, a 26 mold casting wheel and an anode press machine. Copper is electrorefined in a tank house equipped with 768 commercial cells, 44 stripper cells, and 40 liberator cells, utilizing two electrolyte circuits and a 21,000 Ampere rectifier.During 1989 through 1994 a program for improving productivity was carried out by increasing the number of cells and increasing current density to the total rectifier capacity. As a result, a capacity 215,000 stpy of refined copper, 2 million tr. oz silver and 6,000 tr. oz gold per year was achieved. In 1994 Southern Peru announced plans to increase capacity to 250,000 stpy of cathode with a US$ 18 million investment and a US$ 2 million investment in environmental improvement projects, as part of the purchase agreement with the Peruvian government.This paper outlines the scope of the SPCC lio Refinery modernization and environmental program. It describes the implementation of the Electrolytic Plant expansion based on instaliation of polymer concrete cells, a new rectifier, a new selenium roaster and a Precious Metal Plant upgrades."

Jan 1, 1997

By J. -C. Tedenac, C. Colinet, X. Tao, P. Jund, R. Viennois

"We report an ab-initio study of the stability and electronic properties of transition metal silicides in order to study their potential for high temperature thermoelectric applications. We focus on the family M5Si3 (M = Ta, W) which is stable up to about 2000 °C. We first investigate the structural stability of the two compounds and then determine the thermopower of the equilibrium structure using the electronic density of states and Mott’s law. We find that W5Si3 has a relatively large thermopower but probably not sufficient enough for thermoelectric applications.IntroductionIn the search of new sustainable energies, thermogeneration of electricity is one of the promising ways, notably because it is able to produce electricity from different kinds of heat wastes and to its portability. However, despite recent progress in the field, the state-of-the art materials have specificities making their mass-production difficult or even impossible: toxicity (thallium, chalcogen or/and pnictogen based alloys), weak abundance (tellurium based alloys) or cost (germanium or rare-earth based alloys). For all these reasons, finding thermoelectric materials without these drawbacks is vital if we wish to use high temperature thermoelectricity for generating electricity in the near future. Due to their abundance, low cost and low toxicity, transition metal silicides are candidate materials of primary interest and the slightest advance in this field would immediately find an application for the thermogeneration of electricity."

Jan 1, 2011

By V. B. Telles, D. C. R. Espinosa, J. A. S. Tenório

"The purpose of this work was to study the reutilization of the steelmaking dust, derived from steel production in the electric arc furnace (EAF), in iron ore sintering process aiming zinc elimination. In each sintering process were collected sintered samples, these materials were analyzed by chemical analysis using atomic absorption spectrophotometry in order to determine the zinc content. Samples of not sintered mixtures were also characterized by chemical analysis aiming to determine the initial amounts of zinc, i.e. in order to check the zinc amounts present in the mixture before the sintering process. The comparation among the zinc contents of samples sintered and not sintered allowed to determine the elimination of zinc during the experiments. Results showed that the zinc elimination in the process is proportional to the ratio reducer/waste. The zinc removal was lower when the reducer/waste ratio was decreased.IntroductionThe electric arc furnace dust (EAFD) is a residue generated in the steelmaking process using electric arc furnace. Aproximately 30% of all steel produced (in the year 2009) was obtained through electric arc furance (EAF). In the United States of America the percentage of this process in the total crude steel production was about 62% in 2009, while in 2000 this percentage was only 47% [1].The iron ore sintering is a process that reuses wastes generated in metallurgical industries. However, the materials used must be physical and chemical characteristics compatible with the blast furnaces.The quantity of zinc, cadmium, chrome and other metals present in the EAFD depends on the quality of the scrap used to feed the EAF and the type of steel that it is been made [2,3]. The reuse of EAFD waste is interesting to steelmaking processes because of its iron content. However the presence of zinc inside a blast furnace is undesirable since the zinc oxide can be deposited on the blast furnace walls and in the drivers of gas output, interrupting the flow. Another part of the zinc oxide can form deposits on the refractory lining of the blast furnace [4,5]."

Jan 1, 2012

By Ray Y. Lin

Chemical vapor deposition of tungsten carbide on the surface of steel has been investigated at temperatures between 400 and 550C in an atmosphere containing tungsten hexafluoride, hydrogen and benzene. The tungsten fluoride flow rate was maintained at 20 ml/min. The hydrogen flow rate was at 100 ml/min. The benzene concentration varied from 1.15 to 5.56% in the reaction gas. It was observed that the higher the temperature, the faster the deposition rate for tungsten carbide. But the dependence of the deposition rate on the benzene concentration was not systematic. From the x-ray diffraction analysis, it was observed that W, W2C and WC are all presented in the coating. The amount of each phase presented in the coating depends on the temperature and, to a less extent, on the benzene concentration. The microhardness measurement has also been done for all CVD carbide coatings obtained in this study.

Jan 1, 1992

By L. H. Lewis

The relationships that link microstructural properties of advanced permanent magnet materials with magnetic properties such as the coercivity are often difficult to quantify, especially in materials with nano-scale structures. Recent work on RE2Fe14B-based powders fabricated with rapid- solidification techniques such as inert gas atomization (IGA) and melt-spinning provide insight into the nanostructural features which affect the acquisition and stability of coercivity. In all cases the coercivity is found to be a function of both the scale of the constituent microstructure and of the presence and distribution of minor phases.

Jan 1, 1997

By G. Ramadorai

"This paper addresses processing options for recovering gold from carbonaceous sulfidic gold ores. These include, but not limited, to the following methods: (1) Hypochlorite pretreatment followed by cyanidization; (2) Chemical blanking agents pre-treatment followed by cyanidization; (3) Non-cyanide heap leaching techniques; (4) biological pre-treatment followed by cyanidization; (5) biological pre-treatment followed by non cyanide heap leaching. Issues of costs, economics, recoveries, testing methods, state of advancement etc., will be discussed in the paper.ABSTRACT ONLY"

Jan 1, 1997

By Toshiyuki Nohira, Eiichi Takeuchi, Tetsuo Oishi, Hideki Ono, Hirokazu Konishi

The Dy-Nd-Pr-Ni alloy sample was prepared by cathodic potentiostatic electrolysis at 0.65 V (vs. Li+/Li) for 1 h using a Ni plate in a molten LiCl-KCl-DyCl3-NdCl3-PrCl3 system at 723 K. The highest mass ratio (Dy/Nd+Pr) in the alloy sample was observed to be 50 at 0.65 V. Anodic potentiostatic electrolysis at 2.20 V for 12 h was conducted using the Nd-Fe-B magnet electrode in a molten LiCl-KCl system. All elements were almost dissolved from the magnet, and the original form of the magnet disintegrated. After anodic potentiostatic electrolysis at 2.20 V, cathodic potentiostatic electrolysis was conducted at 1.00 V for 5 h using a Mo plate in order to remove the dissolved Fe from the bath. Finally, cathodic potentiostatic electrolysis was conducted at 0.65 V for 12 h using a Ni plate. The mass ratio of Dy/Nd in the alloy sample was determined to be about 18.

Jan 1, 2015

By Liu Chunpeng

Under an inert atmosphere, the temperature enhancement of nickel bearing pyrrhotite irradiated by microwave was measured with a special metal-sheathed thermocouple and the non-isothermal rate equations were obtained. Under the controlled oxygen potential of the reacting gas in the microwave field, over 90% sulfur contained in the pyrrhotite is converted into elemental sulfur directly, the iron and the nickel are transformed into FeO,, NiO, NiFe,O, and FeSiO,. According to the experimental data the rate of the elemental sulfur produced is in diffusional control and the non-isothermal equation derived is

Jan 1, 1993

By René Winand

The paper gives a synthesis of research work performed in the department during the last ten years and dealing with cobalt , copper and manganese electrodeposition in chloride aqueous solutions. Special emphasis is given to electrocrystallization. For copper, properties of the electrolyte such as solubility limits, electrical conductivity and complex ions stability are discussed in connection with leaching, purification of the electrolyte, and metal recovery. When possible, kinetic parameters and probable electrode mechanisms are given. Problems that are still to be solved are also listed.

Jan 1, 1985

By N. J. Themelis

In the last two decades, the Outokumpu flash smelting process has become the dominant new technology for copper smelting and has? also been applied to the smelting of other metal sulfides. The application of oxygen enrichment and improvements in concentrate burner and furnace design have resulted in ever increasing smelting rates per unit volume of the reaction shaft. This paper examines the. rate phenomena taking place in the reaction shaft of the Outokumpu furnace and compares information obtained from a mathematical model of heat and mass transfer rates to results obtained in pi1ot tests conducted at Pori, Finland, and to actual performance of a number of flash smelters around the world. 2?

Jan 1, 1985

By Akira Yazawa

Oxidic dissolution loss of metal in slag is discussed thermodynamically in terms of oxygen potential, activity coefficient and equilibrium constant. To understand basic principle, regular solution model is applied for model calculation of the activity behaviour of metal oxide in FeO-SiO2-CaO slag, and effects of slag composition, temperature, and basicity of oxide on dissolution loss are demonstrated. As: a simplified but practical conclusion, the dissolved metal loss in slag is inversely proportional to activity coefficient of metal oxide, and also to FeO content in slag when amount of slag is taken account.

Jan 1, 1994

By W. L. Dalmijn

The processing of scrap and scrap cars starts with size reduction by a hammermill, or shredder. After the liberation the magnetic fraction is removed. The remaining non¬magnetic fraction mixed with other materials is screened and each fraction is processed separately. The increased use of plastic has a negative effect on the recovery of metals and waste production. At Huron Valley, Belleville Michigen, USA, the non-ferrous fraction from 5 million obsolete cars per year, containing 200,000 tons of non-ferrous metal, is processed. Aluminium Is recovered with a heavy medium separation process and concentrated with eddy current separators. The remaining heavy non-ferrous fraction is concentrated by a new combination of eddy current separation and image processing. After this separation process the zinc fraction is melted and refined and the copper, brass, stainless steel and other high-quality concentrates are sold to the secondary industries. The recycling of car scrap has become an important source of metals and materials for the secondary. materials processing industry.

Jan 1, 1995

By Akira Yazawa, Kazuo Koike, Mitsuhisa Hino

"The vapor pressures of MS (PbS, SnS and Sb2S3) in the molten Cu2S-MS, FeS-MS pseudo-binary and Cu2S-FeS-MS ternary systems were measured by means of a transportation method in the temperature range of 1323 and 1423K to calculate MS activities in the sulfide melts. The activities of MS in these systems show negative deviation from ideal behavior except the FeS binary systems which exhibit nearly ideal behavior in the homogeneous melts. The activities of the Cu2S-FeS pseudobinary system, which is fundamentals of the copper matte, were estimated from the activity values in the ternary systems and exhibit negative deviation from ideality.The distribution behavior of tin between the ·matte and silica saturated fayalite slag was investigated under the controlled partial pressures of S02 at l 523K. It was found that, in general, tin is distributed in the both phase, while tin is concentrated to the slag phase with increasing copper content in the matte. The activity coefficient of SnO in the slag was calculated based on the distribution ratio combined with the activity coefficient in the Cu2S-FeS system.IntroductionThe thermodynamic properties related to the Cu2S-FeS system and the Cu2S-FeS-MS systems (where MS can be PbS, SnS, Sb2S3, As2S3, Bi2S3, etc.) is required to be better understanding of the copper smelting process. However, thermodynamic analysis such as the distribution of impurities among the gas, slag and matte phases is difficult due to lack of thermodynamic data. In this study, the vapor pressures of MS (PbS, SnS and Sb2S3) in the Cu2S-MS, FeS-MS. and Cu2S-FeS-MS systems were measured by a transportation method. The distribution behavior of tin between the matte and silica saturated fayalite slag was also investigated. The results in the present experiments are useful to analyze thermodynamically the behavior of component in the copper matte smelting."

Jan 1, 2000

By Duclerc Fernandes Parra, Luis Filipe Carvalho Pedroso Lima, Harumi Otaguro, Washington Luiz Oliani, Hélio Fernando Rodrigues Ferreto, Ademar Benevolo Lugao

The activation of three polyethylenes, the low density, the high density and the linear low density polyethylene, was determined by means of dynamic mechanical analysis (DMA). Storage modulus and tan δ spectra were obtained as a function of the temperature from −60 to 50 °C with a heating rate of 2° min−1 at frequencies of 1, 2 and 5 Hz and measurement strain amplitude of 10−5. In the tan δ spectra, a small peak in the β region of the three polyethylenes was found and substantiated by subtracting the growing exponential background. This procedure was based on a model that associates the dislocation motion on metals under cyclic stress to vibrating strings and considering the same for the polymeric chains. For the determination of the activation energy we have utilized the frequency versus the reciprocal of the absolute temperature peak of the tan δ. The values obtained for the three polyethylenes, the low density, the high density and the linear low density were, 362 ± 12, 266 ± 9 and 197 ± 6 kJ mol−1, respectively, which were compared with those presented in the literature.

Mar 1, 2017

By Yang Jian-guang, Deng Zi-xiang, Zhang Xu-liang, Li Jun-yuan

"Hyperaccumulator biomass harvested after heavy-metal phytoremediation must be considered as hazardous waste that should be contained or treated appropriately before disposal or reuse. As a potential method to detoxify the biomass and to convert this material to a suitable bio-energy resource, the hydrothermal upgrading process was applied to remove heavy metals and upgrading crude bio-oil from Pteris vittata stems and leaves harvest. Parameters such as material granularity, temperature, Liquid/Solid (L/S, ml/g), pressure, duration and catalysts were examined for their effect on the removal efficiency of heavy metals and upgrading efficiency of crude bio-oil. Maximum heavy metal removal efficiency of>99% and crude bio-oil upgrading efficiency of 83% were attained with an 200 mesh (75 µm) granularity, LIS 40:1and23 MPa at 380°C in the presence ofO.l mol L-1 K2C03 for 30 min. GC-MS analysis results show that the resulting bio-oil mainly consists of benzene 11 %, ketone 42%, alcohols 14%, alkene 15% and ester 11 %, etc., and the relative molecular weight distribution lies in 94-282, carbon number distribution lies in 6-18, calorific value is 32MJkg-1.IntroductionPhytoremediation of soil or water with hyperaccumulator has been extensively explored in recent years [1-4]. Living plants can clean up soils or waterways. This approach exploits the ability of various plant species to thrive in high metal environments where large amounts of toxic elements are accumulated, such as heavy metals, and is particularly appropriate when slow remediation of relatively low metal concentrations is acceptable. Advantages compared with existing remediation methods include the minimal site destruction and destabilization, low environmental impact, and favourable aesthetics; advantages compared with biosorption include continuous in situ regeneration of the biomass, and the ability of living plant cells to supplement passive sorption of metals with metabolic mechanisms of metal uptake and detoxification [5-8]."

Jan 1, 2014

By Vince Newberry

Alcan Rolled Products at Oswego, New York, commissioned Recycle II during May of 1995. Recycle II is an advanced technology UBC recycling facility designed to meet the most stringent environmental standards enforced to date in the United States, particularly with respect to NO, and particulate emissions. This paper addresses the exacting requirements and strategies of Alcan's Recycle II project andThorpe Technologies' design considerations and solutions for the supply of environmentally favorable melting furnace and delacquering systems. The furnaces are equipped with low NOx regenerative burners and furnace pressure and hearth gas flow controls designed specifically for processing the hearth gases through baghouses. The delacquering system is a new generation Apros concurrent flow unit designed for low NOx emissions.

Jan 1, 1995