Search Documents

By Peter Zhang, Dan Neilans, Scott Peterson, Scott Wade, Joe Pugh, Ryan Mcgrady

"A coal outburst is a severe safety hazard in room-and-pillar mining under deep cover. It is more likely to occur during pillar retreating. Multi-seam mining dramatically increases the risk of coal outburst within the influence zones created by remnant pillars and gob-solid boundaries. Though coal outburst is generally associated with heavy loading of coal pillars, its occurrence is difficult to predict. Risk management provides a proactive tool to minimize coal outburst in room-and-pillar mining under deep cover. Risk assessment is the first step in identifying and quantifying outburst risk factors. The primary risk factors for coal outburst are overburden depth, roof and floor strength, geological anomalies, mining type, multi-seam mining, and panel width. A risk assessment chart can be used to proactively screen out mining sections with high risk of coal outburst for further analysis. Gob-solid boundaries and remnant pillars are critical factors in evaluation of the coal outburst risk of multi-seam mining. Risk identification, risk assessment, geologic influence mapping, geotechnical evaluation, risk analysis, risk mitigation, and monitoring are essential elements of coal outburst risk management process. Training is an integral part of risk management for risk identification and communication between all the stakeholders including management, technical and safety personnel, and miners.INTRODUCTIONA coal outburst is a sudden violent burst of coal from a pillar with broken coal or blocks of coal forcibly ejected into open entries. A coal outburst is a severe safety hazard as the mining crew is highly exposed at the site when the event occurs. Though deep cover and strong roof and floor are underlying geologic conditions of a potential burst incident, its real occurrence is also the result of additional mining factors. In room-and-pillar mining, a coal outburst could occur during both development and pillar retreating, but the latter greatly increases the risk of outburst. The other risk factors of coal outburst also include mining layout, multi-seam mining, presence of adjacent gob, cutting sequence, and local abnormal geologic conditions. Over the years, the cases of coal outbursts have been studied by many researchers and mining practitioners(Peng, 2008; Newman, 2008; Iannacchione and Tadolini, 2008; Gauna and Phillipson, 2008; Hoelle, 2008; and Newman, 2002). It is commonly believed that the coal outburst is the result of a sudden release of elastic strain energy stored in coal pillars and is highly associated with cutting into heavily loaded coal pillars, but its occurrence is a rare event and is difficult to predict. A number of engineering controls have been recommended to mitigate outburst potential. For room-and-pillar mining, sufficient pillar sizes have been the primary control for coal outburst prevention. The pillar design tools such as ARMPS and AMSS developed by NIOSH have played an important role in the design of stable pillars to prevent pillar collapse and squeezing as well as coal outbursts. In fact, with the implementation of pillar design using proper stability factors, pillar collapse and squeezing have been almost eliminated, and the number of coal outbursts has been greatly reduced in the US over the past decade. However, after a few outbursts occurred during pillar retreating in the US over the past a few years (MSHA, 1996; MSHA, 2014; MSHA, 2013), it has been realized that sufficient pillar size is still not enough to prevent coal outbursts. The investigations of the incidents showed that other factors such as multi-seam mining, panel layout, cutting sequence, and local geologic factors also seemed critical in causing the events. Therefore, it has become imperative that additional proactive measures beyond proper pillar design be implemented to prevent coal outbursts."

Jan 1, 2015

By Bob Coutts, Matt Martin, Dan Lynch, Dan Payne

"The Broadmeadow punch longwall coal mine in Central Queensland Australia has experienced significant highwall movement associated with the effect of longwall subsidence when the longwalls approach their final position close to the open-cut highwall. In response to this movement, Broadmeadow employed two types of broadscale highwall monitoring (radar and laser scanners) to provide full coverage measurement throughout three consecutive longwalls approaching the highwall. This was to attain a better understanding of the mechanism causing the movement and potentially enable prediction of instability. Results from the monitoring found the highwall is displaced to magnitudes unlike those typically measured in open-cut mining and in direct contrast with typical longwall subsidence behaviour.This paper discusses the ground movements measured, monitoring methods used, safety measures established, as well as theorising the failure mechanism. Recommendations are made for mine and pit designs for future punch longwall layouts. The paper shows how the movements measured are more aligned to some measurements made during stream valley closure studies previously presented at the ICGCM and challenge the mechanisms suggested by previous literature.BACKGROUNDThe mining of longwalls under or adjacent to large voids (e.g., stream valleys, escarpments, or cliffs) is commonly associated with heavily vegetated or steep surface areas. In areas of extreme topographic variance, access to traditional survey pegs and stations or even new radar or laser technologies is limited. In addition, seldom have the longwall layouts aligned themselves parallel or perpendicular to the surface feature, making interpretation of any available surface movement data more complicated.The punch longwall layout (Figure 1) is also quite uncommon (only undertaken at a small number of longwall mines in Australia) but creates the perfect configuration to enable a somewhat controlled study of the effect of longwall subsidence on a steeply dipping surface feature (an un-vegetated, evenly excavated open-cut highwall). The relatively recently developed radar and laser scanning technology has also enabled near continuous, real-time, sub-millimetre monitoring of a full 500m wide x 100m high highwall. Because the punch longwall enables access and a clear view, the technology could be easily deployed as compared to the highly vegetated and variable topography of stream valleys."

Jan 1, 2018

By Ben Mirabile

Over the past three decades, the U.S. coal mining industry has widely used cable supports to supplement traditional primary bolting systems, especially in difficult ground conditions. However, increased mining activity in adverse conditions has underscored the limited effectiveness of the non-tensioned, partially grouted cable supports used to supplement primary bolts. Roof failures in conditions such as corrosive environments, highly laminated strata, low overburden depth and water intrusion have demonstrated that the need for cable technology has reached beyond the traditional non-tensioned, partially-grouted cable tendon. Furthermore, declining market conditions and increased competition for coal customers has demanded that new cable bolt technology be costeffective and readily adaptable to the mining cycle. Jennmar Corporation has developed several cable bolt technologies that can be used as stand-alone solutions or in concert with one another to mitigate adverse conditions. These technologies include rapid tensioning of cable supports, structural surface control and polyurethane injection. The case studies presented in this paper use one or more of these technologies to address adverse mining conditions or special ground control problems.

Jan 1, 2013

By William Blake

Mining induced rock bursts have been a severe operational hazard associated with the deep silver mines of the Coeur d'Alene mining district for over 30 years. Recent studies during the past fm years have led to a better understanding of the different types of rook bursts and their causative mechanisms. This has resulted in ground control measures that more effectively minimize burst occurrences as well as contain burst damage. Case histories of burst incidences and examples of control measures are presented.

Jan 1, 1987

By Hai Rong

EH-4 Electrical conductivity imaging system has been playing an important role in prospecting, looking for water resource, and determining coal mine gob boundary by virtue of its significant advantages such as collection of large volume of data, light weight, fast analysis, high-precision, and low cost. However, it has little application in determining the overburden failure zone and development of water flowing fractured zone and bed separation space in complex extra thick coal seam conditions. In order to confirm the overburden failure range and evolution of water flowing fractured zone and bed separations in complex extra thick coal seam conditions the panel 63005 of Laohutai coal mine in China was selected for study in this paper,. EH-4 magnetotelluric method was used to determine the overburden failure zones and bed separations in the overburden. Theoretical analysis and numerical simulation were employed to verify the EH4 survey results. The results show that the failure height in the overburden of the three coal splits was 120m to 170m before panel mining, and increased to 150m to 220m after panel mining. The overburden failure height was on average 7.4 times the equivalent mining height in complex extra thick coal seam condition of Laohutai coal mine when the sand backfilling and fully mechanized top coal caving methods were employed. After mining of panel 63005 started, bed separations were found on the hanging wall and footwall of the F18 fault where water bodies existed. The results obtained in this research not only provide a theoretical guidance for safe mining at Laohutai coal mine but also serve as a reference for predicting and preventing water inrush accidents for coal mines under similar condition in China.

Jan 1, 2014

By Erik Westman, Benjamin Mirabile

"Quantitative evaluation of secondary support performance in longwall tailgates in U.S. coal mines was introduced with the U.S. Bureau of Mines (USBM) Wood Crib Performance Model. This model evaluated crib performance based on load capacity, stability, and convergence characteristics. The introduction of a large variety of alternative secondary supports in the 1990s prompted a full-scale load-displacement testing program conducted by the USBM and, subsequently, NIOSH. The application of the ground response curve concept to secondary supports provided a more complete estimation of secondary support loading in longwall abutment zones. Secondary support loading from floor heave, horizontal stress effects, and pillar yield are captured by the ground response curve. A point on the ground response curve can be measured by instrumenting a secondary support with load and convergence measurement devices. A segment of the ground response curve can be measured by instrumenting two secondary support types of varying stiffness. Numerical models have been used to construct complete ground response curves for longwall tailgates based on measured secondary support performance. The ground response curve concept can be used as a design methodology for secondary supports in the #2 entry, as well as the longwall tailgate. Extending published evaluation and design methodologies for secondary support in longwall tailgates, a ground response curve unique to the loading conditions and required functionality of the #2 entry can be developed. Numerical models can be used to construct full ground response curves based on measured data in the #2 entry.INTRODUCTIONA longwall ventilation system is designed to continuously dilute and move methane-air mixtures and other contaminants from the active face, to bleeder systems, and out of the mine. The #2 entry of the tailgate gateroad serves to transport contaminated air from the longwall face to the bleeder system. The #2 entry is required to function as an air course between two longwall gobs and is subject to significant ground movement and loading. Current ground support design and evaluation practices are based on empirical evidence and little to no quantitative data on support performance exists for these entries. Substantial volumes of research have been conducted on ground movement and support performance in longwall tailgate entries. Following the successful ground support evaluation and design practices established for longwall tailgate entries, a practical and efficient design methodology can be adapted for supporting the #2 entry of a three-entry gateroad system."

Jan 1, 2018

By Robert B. Francini

Longwall mining and pipelines have coexisted since longwall mining was introduced into the United States. How the pipeline operator reacts to longwall mining under their line depends on many factors. This paper outlines the process the pipeline operator goes through to determine the appropriate response when their pipeline is being undermined. Typical mitigation procedures are reviewed. Finally, the paper looks at current design practices for new pipelines that are expected to be undermined during their lifetime.

Jan 1, 2011

By Ben Fahrman

The classical approach to engineering design involves the purely deterministic calculation of the factor of safety, the ratio of strength to stress. The factor of safety is an easy calculation to perform in many circumstances, and it is very easy to interpret the results. The simplicity of the method is both a strength and a weakness. The results of the deterministic factor of safety calculation are simple to determine and interpret, but they have no ability to account for the uncertainty present in the inputs or outputs. Uncertainty is prevalent in geotechnical engineering applications. This uncertainty can stem from spatial variability, poor sampling, a dynamically changing environment, etc. Probability analyses allow input parameters to take the form of a distribution rather than a single value, making them uniquely equipped to handle the uncertainty inherent in geotechnical engineering design considerations. A stochastic approach also has the benefit of providing results as a probability of failure, which is more meaningful than a factor of safety. Though stochastic modeling is becoming more common in many geotechnical applications, it is still not widely used for coal pillar design. The objectives of this study are to justify the concept of using a stochastic approach to coal pillar design and to compare the results of a simple stochastic analysis to those of standard industry practice. A simple synthetic study was performed to compare the results of a probabilistic analysis of coal pillar design to the results obtained from running ARMPS, which is published by NIOSH. Normal distributions were assigned to each input parameter that is required to determine the factor of safety of a single coal pillar. The probability of failure resulting from the synthetic study was found to be more conservative than the ARMPS stability factor. A probabilistic approach to coal pillar design is discussed in comparison to the traditional deterministic approach. The greatest strengths of the probabilistic approach were determined to be the effective handling of uncertainty and the increased meaning of the inputs and outputs inherent to a probabilistic approach.

Jan 1, 2013

By Joe Zelanko

In order to prevent roof fall accidents and injuries, U.S. underground coal mine operators must develop and implement effective roof control strategies. Various tools are available to assist engineers in developing designs. For example, criteria to address global stability issues (e.g., pillar stability) are well established in the U.S.; effective tools (e.g., empirical and numerical) are available to diagnose potential problems and avoid catastrophic failures. However, most miner injuries occur as a result of local instability (e.g., a roof fall in a single heading or a rib roll from a pillar corner). Hazard recognition and the availability of support plans suitable to those conditions are key to maintaining stability and safety on the working section.

Jan 1, 2011

By Christopher Mark

Coal bursts are typically associated with highly stressed coal. Most bursts occur during retreat mining (longwall mining or pillar recovery) in highly stressed locations like the tailgate corner of the longwall panel. Others are associated with multiple seam interactions. However, a small but significant percentage of coal bursts have occurred during development or in outby locations unaffected by active mining. Most development bursts have been relatively small, but some have been highly destructive. No theory of coal bursts can be complete if it does not account for this type of event. This paper focusses on the development mining coal burst experience in the US, putting it into the context of the entire US coal burst database. The first documented development coal burst occurred almost exactly 100 years ago during slope drivage at the Sunnyside Mine in Utah. Sunnyside subsequently had a long history of bursts, mainly during retreat mining but also during development. Several Colorado mines have also experienced multiple development bursts. Some, but by no means all, of the development bursts in these western US coalfields have been associated with faults. In the Central Appalachian coalfields, most development bursts have occurred in multiple seam situations. In some of these cases, however, there was no retreat mining in either seam. The paper closes with some lessons from this history, with implications for preventing such events in the future.

Jan 1, 2017

By Jesse Puller, Ken W. Mills, Owen Salisbury

"An underground coal mine located in New South Wales has a target coal seam located 160-180 m deep directly below a 16-20 m thick conglomerate unit that has been associated with significant periodic weighting events on the longwall face. As part of the investigations to better understand the causes of periodic weighting at the mine, inclinometers capable of measuring horizontal shear movements through the full section of the overburden strata were installed ahead of mining at two locations approximately 1 km apart above the centre of two longwall panels. These inclinometers were monitored as the longwall approached each site. This paper presents the details of the installation, the results of the inclinometer monitoring at both sites, and the insights that these measurements provide for overburden behaviour about longwall panels.Horizontal shear movements were observed to develop on shear horizons that correlate closely across the two sites suggesting a mechanism that is consistent across a large area of the mine. Shear movements were observed to develop on a single horizon near the top of the conglomerate strata that was mobilised almost immediately after initial formation of the longwall goaf at a distance of 425 m ahead of the longwall face. The direction of horizontal movement was consistent with the relief of the major principal horizontal stress. As the longwall face approached each inclinometer, other horizons within the upper part of the overburden strata begin to shear with the upper strata moving toward the approaching goaf more than the lower strata. Within the last 30 m of longwall approach, tilting of the strata associated with the increase in vertical subsidence toward the extracted goaf caused a change in the style of deformation with tilting and reverse shear offsets.INTRODUCTIONLongwall mining is recognised from subsidence monitoring, surface extensometer measurements, and various other observations to cause significant disturbance to the overburden strata directly above the extracted goaf of each longwall panel. Disturbance to the overburden strata beyond the limits of each longwall panel is not so well understood. Subsidence monitoring indicates that horizontal movements beyond the edges of the extracted longwall panel are generally greater in magnitude than vertical subsidence and horizontal movements may extend up to several kilometres from the edge of the panel in some circumstances (Reid 1998, Reid 2001, Hebblewhite et al 2000, Mills 2001, Mills 2014). The mechanics of how these movements are accommodated within the overburden strata is only poorly understood and there are few direct measurements."

Jan 1, 2015

By R. Quentin Eades, Kyle Perry

"Surface mines continue to implement highwalls for several reasons, such as increasing recovery, improving margins, and justifying higher stripping ratios. Highwall stability is a complex issue that is dependent upon a variety of mining and geologic factors, and a safe design is necessary for a successful surface operation. To improve highwall stability, it is important to understand the connection between local geology and blasting.Explosives are employed throughout the mining industry for primary rock breakage. There are a number of controlled blasting techniques that can be implemented to improve highwall stability. These include line drilling, smooth wall blasting, trim blasting, buffer blasting, air decking, and presplitting. Each of these techniques have associated advantages and disadvantages. Understanding local geology is necessary for selecting the appropriate controlled blasting technique. Furthermore, understanding the limitations and conditions for successful implementation of each technique is necessary. A discussion of the impact of geologic conditions on highwall stability is provided. Additionally, discussion is provided for the successful incorporation of the controlled blasting techniques listed above, and the associated mining and geologic factors that influence the selection and design of controlled blasting plans. Finally, a new methodology is proposed.INTRODUCTIONExplosives are used throughout the mining industry as the standard for primary rock breakage, a critical part of the mining cycle. In 2015, the U.S.. consumed 2.2 million tons of explosives (Apodaca, 2015). The coal mining industry accounted for the majority of explosive consumption, accounting for approximately 63% of total explosives. The quarrying and nonmetal mining industries accounted for 12% of explosive consumption, and the metal mining industry accounted for 9% (Apodaca, 2015). This constitutes 84% of the explosives used in the U.S. However, the energy released during the detonation process is often in excess of that required to adequately fragment the surrounding rock (Jhanwar and Jethwa, 2000). This excessive energy, along with over confinement and poor blast geometry, will cause damage to the undisturbed rock mass beyond the intended boundary of the blast. This event is known as overbreak or back-break (ISEE, 2011)."

Jan 1, 2018

By Yang Li

For the study of overburden movement in longwall mining of shallow coal seams, most scholars merely consider the thickness of bedrock and top soils. In this paper, the overburden movement in longwall mining of shallow coal seams with thin top soils and key strata group was studied. By using numerical simulation, the development of fractures in the overburden was analyzed for different ratios of panel width to depth (W/D) and depth to mining height. The results show that the overburden movement changed with the variation of mining height, panel width and depth under the specific geological conditions. It also explain how different overburden disturbance structures, such as ?three zones? (caved, fractured, and continuous deformation zones), ?two zones?(caved and fractured zones) or ?steps-like collapse? are formed under different mining conditions. The results broaden the vision for research on overburden movement in longwall mining of shallow coal seams.

Jan 1, 2014

By Peng Zhang

In previous research, the laminated overburden model from the LaModel program was effectively integrated with Analysis of Retreat Mining Pillar Stability (ARMPS) through ARMPS-like input to create a laboratory version of the new ?ARMPS-LAM? program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition, and then automatically develops, grids, runs, and analyzes a full LaModel analysis of the mining geometry to output the section stability factor (SF), all without further user input. The initial ARMPS-LAM results were encouraging with a case history classification accuracy of 55% to 71%; however, a few of the input variables that were nominally included in the SF calculation showed independent significance in the classification accuracy. Therefore, in order to further improve the accuracy of the ARMPS-LAM program, an investigation of the SFs calculated by the new ARMPS-LAM program and the ARMPS program is detailed in this paper. The initial results of a linear correlation between the ARMPS-LAM SF and the ARMPS SF showed a strong correlation (R2 = 0.88), with the ARMPS-LAM SF averaging about 8% higher. The difference in SFs between the programs were further investigated, and, ultimately, the results indicated that the laminated overburden model as implemented in ARMPS-LAM distributes relatively more load on the section pillars for depths less than about 1,000 ft and less load for depths more than 1,000 ft. The results of this research highlight the potential for improving the ARMPS-LAM program in the future by implementing a more accurate loading calculation on the section pillars.

Jan 1, 2014

By Morgan Sears

The LaModel program (Heasley, 1998) is a displacement discontinuity, boundary element model (BEM) for analyzing stresses and displacements in single and multiple-seam coal mines. After the Crandall Canyon mine collapse, the need for better design guidelines for LaModel was observed and a new calibration method for deep cover pillar retreat was developed (Heasley et al., 2010). However, the scope of this initial calibration was limited to single-seam mines deeper than 750 ft. This limited application of the initial calibration method lead directly to the research presented in this paper, which attempts to define appropriate LaModel calibration guidelines for pillar design where shallow cover and/ or multiple-seam mining scenarios are encountered. As part of this research, a database of shallow cover case histories has been developed, and this database is used to help validate the shallow cover calibration method. By adding the shallow cover database to the previous deep cover database, the LaModel calibration method has now been extended to the complete range of mining depths, as well as to multiple-seam cases. With this shallow cover calibration, the utility of the LaModel program continues to increase.

Jan 1, 2013

By Yvette Heritage

"The risk of fatalities from rib failure is still prevalent in the coal mining industry. This risk has prompted further research to be conducted on rib deformation in order to understand the mechanisms of rib failure, with the long-term objective being to improve rib support design. This paper presents the results of ACARP research project C25057, which investigated the mechanics and drivers of rib failure. The results of rib deformation monitoring at three different mines in Australia provides rib deformation characteristics for overburden depths ranging from 160 m to 530 m. Monitoring includes deformation during development drivage conditions and during the longwall retreat abutment stress environment. The rib deformation monitoring covered three different seams: the Goonyella Middle Seam, Ulan Seam, and Bulli Seam in the Bowen Basin, Western Coalfield, and Southern Coalfield, respectively. The observed mechanisms driving the rib deformation ranged from bedding shear failure along weak claystone bands to vertical shear fractures to kinematic failures driven by shear failure dilation. The variation in mechanisms of rib failure, together with the seemingly consistent method of rib support design, prompts the question: What exactly is the role of rib support?INTRODUCTIONThe current risk of rib fatalities in the coal mining industry has prompted further research into understanding the mechanisms of rib failure. Three Australian mines assisted further research by providing sites for rib deformation studies as part of the Australian Coal Association Research Program (ACARP) project C25057. The mines included in this study were Moranbah North Mine, Ulan West Mine, and Appin Mine. This paper provides key results of the rib deformation monitoring relevant to assessing the mechanisms of rib deformation.The approach of monitoring rib deformation and rib support loads was used to measure and characterise the dynamic rib deformation present in both development and longwall retreat stress environments. The characterisation of rib deformation, together with rock failure modelling, was used to determine the mechanisms for failure within the rib and to assess the interaction of rib support with the failure process. The mechanisms of rock failure are considered an important factor in understanding the drivers for the failure. Consideration of the site-specific failure mechanisms can provide for a more tailored support design."

Jan 1, 2018

By Darin Cotton, Tim Burgess, Tim Martin

"As the leading US supplier of roof control drills, J. H. Fletcher and Company® has encountered an extensive set of roof strata challenges and has overcome various drilling issues by varying machine parameters and working with customers and tool manufacturers to develop solutions. Every mine wants to drill and install roof bolts as fast as possible with maximum safety at the lowest possible installation cost for their conditions. In most circumstances, the intuitive method of higher speeds and pressures can actually have a detrimental effect on the roof drill safety and performance.This paper will outline recent tests carried out at several different coal mines in the Eastern United States. The tests focused on optimizing the drilling parameters of feed pressure, feed rate, rotation speed, and drill torque.The drill feed, rotation speed, and rotation torque, as well as the type of bit selected, have a definite impact on the performance of the roof drill including drilling speed, safety, and tool life. The drilling process can be improved while also improving operator safety and reducing bolt installation costs by maintaining the appropriate roof drill settings for the specific strata conditions.The advantages of improving the drilling process includes increased bit life, increased drill steel life, reduced hanging drill steels, reduced clogging of the vacuum system, decreased whipping drill steel potential, reduced noise generation, and increased cutting size which reduces fine dust generation and dust collection system servicing.INTRODUCTIONIn recent times, the economic pressures that coal producers are facing have created an increased emphasis on controlling operating costs. Several coal operators have pointed out their dissatisfaction with low bit life, and there is a renewed interest in improving tool life and machine performance as part of an overall cost control strategy. Operators are looking for ways to reduce tooling cost, maintenance costs, and drill downtime without decreasing drill performance. This renewed interest in reducing operating costs, along with the ongoing desire to improve safety, created a perfect environment to take a fresh look at the existing fleet of machines to see what could be accomplished. The goal was to take a practical approach to reviewing machine parameters to determine what changes could be made. The emphasis was on changes that would be feasible to roll out to an entire fleet of machines in a short period of time with minimal capital expenditure. The thought process was that significant improvements could be made by simply tuning up the machine parameters to provide a more efficient and safer bolting process."

Jan 1, 2015

By Andre Zingano

An underground mine using room and pillar and retreat mining methods was developed during the 1950?s. In 2009 an open cast mine was opened in the same reserve with the objective of mining five coal seams including the one previously mined. Recently, a series of slope failures were detected at the open cast mine. The surface mine map was overlain on the underground mine map, and it was observed that the slope failures were located above a retreat mined area where the overburden had caved and the ground subsided. The deformation and displacement attributable to subsidence caused a loss of strength in the overburden strata. The objective of this paper is to study the causes of slope sliding (or failure) due to the ground subsidence of rock layers above oldmined out areas. A map was created to overlay the two mines -- the abandoned underground mine and the active surface mining. Two- and three-dimension numerical modeling was conducted to simulate the slope behavior and to verify whether the mine subsidence was the cause of slope instability. This study indicated that the subsided rock layers were the cause of slope instability and sliding.

Jan 1, 2013

By Daniel W. Su

This paper presents the implementation and evaluation of the hydraulic fracturing technique and Longwall Visual Analysis (LVA) software to mitigate the impact of a 1,000-ft (305-meter) widemassive sandstone channel on a 1,500-ft-wide (457-m-wide) longwall face. Based on a underground roof geology reconnaissance program, four frac holes were drilled and fraced along the center axis of the sandstone channel. To further provide detailed monitoring of the longwall face, the Longwall Visual Analysis (LVA) software was installed to track the face pressure and cavity formation index. In mid-December 2011, the longwall face approached and entered into the western edge of the sandstone channel. The longwall face mined through the center axis of the sandstone channel in mid-January 2012 and advanced outby the eastern edge of the sandstone channel in early February 2012. Results from daily underground observations and production delay analysis confirmed the effectiveness of the hydraulic fracturing program and the validity of the LVA Software.

Jan 1, 2012

By Jimin Su, Enguang Zhu, Kangning Zhang, Yang Li

"The effect of interburden on overlying strata movement during the mining of a lower group coal seam is still a challenge in China. Based on the multiple coal seams in western China, numerical simulation and field tests are applied to study the interburden and overburden movement during the undermining process. This study focuses on the impact of the thickness and structure of the interburden, the proportion of hard rock, and the ratio of the overburden thickness to interburden thickness (OB/IB). In this paper, four typical underground coal mines are simulated for lower seam longwall mining with different interburden parameters. The results indicate that the ratio of the overburden thickness to the interburden thickness is not the dominant actor for multiple seam longwall mining, especially in the mines in western China,which feature shallow depth. The thick and hard interburden could strongly affect the lower coal seam mining process. INTRODUCTION The project background is based on four typical underground coal mines in western China.The information on the overburden and interburden is shown in Table 1. Different overburden to interburden thickness (OB/IB) (Ellenberger, 2009) values of the four coal mines are also studied: 6.2 in Bulianta coal mine, 7.2 in Kaida coal mine, 8.2 in Shigetai coal mine, and 9.4 in Halagou coal mine. The proportions of hard rock in the interburden of the four coal mines are also different: 0% in Kaida coal mine, 70% in Shigetai coal mine, 80% in Bulianta coal mine, and 100% in Halagou coal mine. To be specific: the thickness of interburden are listed as follows: 7m in Halagou coal mine, 6m in Kaida coal mine, 10m in Shigetai coal mine, 28m in Bulianta coal mine. The depth of the upper coal seam are: 66m in Halagou coal mine, 54m in Kaida coal mine, 79m in Shigetai coal mine, 182m in Bulianta coal mine. NUMERICAL SIMULATION UDEC 4.0 is applied in this paper to analyse the overlying strata movement and the interburden failure.(Liu, 2007) This is based on mining in the lower coal seam under the mined-out upper coal seam (Majdi, 2012, Morsy, 2006)."

Jan 1, 2017