Search Documents

By Wenjun Ju

It's very important to determine the limitation of bed separation in entry roof in order to predict roofs stability and take some necessary precautions. Based on numerical modeling and monitoring in the field, the new concept of Limitation of Roof Layer Separation (LRLS) and its method of determination LRLS is given in this paper

Jan 1, 2001

By Tim Miller, Michael M. Murphy, John L. Ellenberger, Gabriel S. Esterhuizen

"A limestone mine in Ohio has had instability problems that have led to massive roof falls extending to the surface. This study focuses on the role that weak, moisture-sensitive floor has in the instability issues. Previous NIOSH research related to this subject did not include analysis for weak floor or weak bands and recommended that when such issues arise they should be investigated further using a more advanced analysis. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to demonstrate the effect that a weak floor has on roof and pillar stability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface.IntroductionMassive roof falls extending to the surface at a limestone mine in Ohio have been studied collaboratively by the National Institute for Occupational Safety and Health (NIOSH) and the mine owners. This paper provides a summary of the sequence of events leading to observed instability and presents a numerical modeling analysis that investigates the role a weak floor can have on roof and pillar stability.This study builds upon previous NIOSH research in underground limestone mines undertaken by way of a survey that analyzed performance of pillars in 34 different stone mines in the Eastern and Midwestern United States between 2005 and 2009 (Esterhuizen et al., 2011). This survey led to the development of underground stone mine pillar design guidelines based upon a “stability factor” for the pillar system. The factor is compared to operational experience to determine ranges of values that are typical of stable pillar systems. A software package titled Stone Mine Pillar Design (S-Pillar) was developed for easy application of these guidelines (Esterhuizen and Murphy, 2011).Weak floor in the present case study departs significantly from cases included in the previous NIOSH research, in that none of the 34 study mines had weak floor issues. Moreover, this case study is the first in which a weak floor has been monitored routinely as roof falls are occurring. A detailed report on the observations and measurements taken at the mine has been published (Murphy et al., 2015). The previous observations led to the conclusion that although there were weak bands in the pillar, the weak floor was the significant defect that led to the instability issues. The pillars were initially mined in 2004, approximately 10 years before the instability issues began to occur. The objective of this study is to use numerical models to analyze a variety of floor strengths and the impact of moisture content to find the critical point at which the floor becomes unstable, leading to long-term instability issues."

Jan 1, 2015

By Jesse Puller, Ken Mills

"This paper describes the Australia, New Zealand Inflatable (ANZI) strain cell, its operation, and recent development for overcoring in exploration boreholes. The ANZI strain cell is an instrument system that uses the overcoring method of stress relief to determine the three-dimensional, in-situ stresses in rock. The instrument has been used successfully for over three decades in numerous underground mining and civil projects, but technical advances over the last decade or so have allowed the system to be deployed in surface exploration boreholes to greater depths than was previously possible. Recent development of a downhole electronic data logger, a wireline-enabled drilling system, and an instrument deployment system has simplified the process of obtaining three-dimensional overcore measurements at depths approaching 1km to a single shift operation.The capability to deploy ANZI strain cells in surface exploration boreholes represents a significant breakthrough for the design of underground mines and underground excavations generally. High-confidence characterisation of the in-situ stresses at the design stage provides the opportunity to design key infrastructure and mining systems to take advantage of the in-situ stress field from the outset before mining begins. Understanding the three-dimensional, in-situ stress field not only provides a measure of the magnitude and direction of loads acting within the rock mass, it also provides insight into the mechanics of all the various processes driving ground deformations, including which geological fault structures are at limiting equilibrium.INTRODUCTIONThe overcoring method of stress relief is one of the most direct methods for determining three-dimensional, in-situ stresses in rock. The Australia, New Zealand Inflatable (ANZI) strain cell combines overcoring with several other techniques to provide determinations of the three-dimensional, in-situ stress field and the properties of the rock and, importantly, provides an indication of how much confidence can be placed in the measurement. This paper describes the advances that have enabled overcoring of the ANZI strain cell in deep surface exploration boreholes and the development of various complementary techniques that build additional confidence in the determination of the in-situ stress."

Jan 1, 2018

By Elizabeth Holley, Meriel Young, Gabriel Walton

"The coal mine roof rating (CMRR) was developed by Chris Mark and Greg Molinda to bridge the gap between geological variation in underground coal mines and engineering design. The CMRR accounts for the compressive strength of the immediate roof, the shear strength and intensity of any discontinuities present, and the moisture sensitivity of the immediate roof. The CMRR has been widely used and validated in Eastern US coal mines, but it has seen limited application in the Western US.This study focuses on roof behavior at a Western coal mine. Mine A shows significant lateral geological variation, along with localized faulting and a laterally extensive sandstone channel network. The CMRR is not used to predict roof instability at the mine.It is, therefore, hypothesized that there are other factors that are correlated with roof instability in underground coal mines that could potentially also be included in the CMRR.This hypothesis was tested by collecting 30 CMRR measurements at Mine A. At each measurement location, a binary record of the roof condition (stable or unstable) was made along with parameters, such as depth of cover, thought to also correlate with roof stability. A statistical analysis of the data was performed to determine the parameters in addition to those included in the CMRR, which can be correlated to roof stability.INTRODUCTION AND BACKGROUNDRoof fall is one of the greatest hazards facing underground coal miners (Barczak et al., 2000). In 2017, 91 lost-time injuries occurred due to roof fall in US underground coal mines. A further 48 roof falls occurred with no lost days (MSHA, 2018).The coal mine roof rating (CMRR) classification was developed by Molinda and Mark (1994) to quantify the geological description of mine roof into a single value that could indicate mine roof stability and be used in engineering design. It is widely used in the Eastern US as an input for the analysis of longwall pillar stability (ALPS) in underground coal mines. It provides an excellent start; however, it is arguably not fully comprehensive, nor is it widely used in the Western US."

Jan 1, 2018

By Andre Zingano, Anderson Weiss

"The objective of this paper is to study the behavior of a low thick and low depth coal seam and the overburden rock mass. The mining method is room and pillar in retreat and partial pillar recovery. The excavation method is conventional drill and blast because of the small production. The partial pillar recovery is about 30% of the previous pillar size, 7m x 7m. The roof displacement was monitored during retreat operation; the surface movement was also monitored. The effect of the blasting vibration on the final pillar strength had been considered. Due to blasting, the pillar reduced about 20%. The consequence is more pillar deformation and roof vertical displacement. The pillar retreat and ground movement were simulated in a three-dimensional numerical model. This model was created to predict the surface subsidence and compare to the subsidence measured. This study showed that the remaining pillar and low seam reduce the subsidence that was predicted with conventional methods.INTRODUCTIONMining low coal seams (less than 1 meter) with the room-and-pillar mining method implies the excavation of part of the roof or floor to maintain adequate entry height for equipment and compliance with labor regulations with respect to ergonomic issues. The direct consequence of this is an increase in coal contamination and the increased cost of transportation and preparation at the plant. Traditional room-and-pillar mining only uses a development operation, even with a continuous miner or drill-and-blasting. Therefore, all the run of mine (ROM) coal is carried out with part of the roof or floor. However, if the retreat mining method were to be considered, the quality of the coal could increase because only the coal seam is excavated from the pillar recovery. The quality of ROM coal will increase, and the cost will decrease proportionally to the amount of coal produced from the retreat operation.However, the retreat mining with partial or total pillar recovery implies greater subsidence. This is particularly true if the coal seam depth is shallow, under 100m depth. Subsidence prediction in room-and-pillar retreat mining is complex; it depends upon the remaining pillar (stump pillar) size, as well as the pillar height, and the behavior of the pillar after retreat. This is related to the strength of the remaining pillar, which is related to the excavated method (drill-and-blast or mechanical)."

Jan 1, 2018

By Gautam Benerjee, Veera Reddy Boothukuri, Bhattacharjee Ram Madhav, Panigrahi Durga Charan

"India’s tryst with mechanized longwall coal mining started with the introduction of the first self-advancing powered support longwall (PSLW) face at Moonidih Colliery of Jharia Coalfield in 1978 and at Godavarikhani (GDK)7 Incline of Singareni Collieries Company Limited (SCCL) in 1983. During the last 37 years, about 30 longwall units in Coal India, Ltd., (CIL) and 10 longwall units in SCCL have been introduced with powered roof supports of varying capacity, ranging from 280 to 800 tonnes, in many mines in India under varying geological and geotechnical conditions. The majority of the longwall faces in India have been worked under relatively shallow cover (up to 200m), and significant strata control problems have been encountered due to poor caveability of the roof, inadequate capacity of the supports, a lack of knowledge on longwall caving mechanisms, less than adequate strata monitoring systems, and the non-availability of quality spare parts, etc. This has resulted in structural damage to supports and increased downtime of the equipment, thereby making longwall mining in India a case of technology failure. Energy demand for a developing country like India with a population of 1.2 billion is huge, and the thrust on increasing coal production continues. However, the share of coal production from underground mines in India continues to decline (current share is around 6%) because of absence of successful mass production technology in underground coal mining. Under this backdrop, a high-capacity longwall with state-of-the-art technology was introduced in 2014 at Adriyala Longwall Project (ALP) of SCCL for the first time in Indian Coal Mining Industry. The first longwall panel (LWP) has been completed successfully. This paper highlights the major geotechnical challenges encountered during development of the longwall gate roads due to the presence of two overlying clay bands, significant in-situ horizontal stresses and the experience of using rigid (welded) steel wire mesh with resin-anchored roof bolts. Efforts have been made to analyze longwall weighting and caving behavior, such as main and periodic weightings, the effect of front and side abutment pressures, and the behavior of gate roadway support systems under immediate friable weak roof with overlying massive sandstone."

Jan 1, 2017

By Kristine L. Pankow, Keith D. Koper, Michael K. McCarter, Jared R. Stein

"The Wasatch Plateau region of central Utah contains a number of active underground coal mines in an area of well-documented natural seismicity. As a result, there are several hundred seismic events recorded in this region every year that may or may not be attributed directly to mining activity. Previous studies have linked the majority of this seismicity to mining activity through various means, but have not attempted to develop a method for categorizing individual events within a seismicity catalog. This study uses both relative relocation and waveform cross-correlation to separate events based on hypocentral depth and waveform similarity, respectively, in the area surrounding a single longwall coal mine within the Wasatch Plateau. We conclude that relative relocation can help with depth discrimination, but there are some unavoidable limitations caused by sparse seismic network coverage. The cross-correlation technique is more promising, with the ability to group events by waveform similarity and track mining progress over both space and time. With cross-correlation based clustering, we confirm that the vast majority (97.6%) of events in the study area are directly related to mining activity, but that a small population of natural seismicity is present as well. Eliminating this natural seismicity from the catalog of seismic events, leaving only those events related to mining, can give operators valuable information about the changing conditions as mining progresses and eliminate concern over events unrelated to mining activity.INTRODUCTIONA number of underground coal mines are located in the Wasatch Plateau region of central Utah, and have been in operation since the late 1800s. This activity has resulted in a well-known history of mining induced seismicity (MIS) (Wong, 1985). Additionally, this area is situated near the border of the Basin and Range and Colorado Plateau physiographic provinces, where naturally occurring tectonic earthquakes also occur (Arabasz et al, 1980). Seismicity separating these physiographic provinces is part of a larger band of seismic activity known as the Intermountain Seismic Belt (ISB) that runs from Montana to Arizona and cuts through the western boundary of the central Utah coalfields (Smith and Arabasz, 1991) (Figure 1)."

Jan 1, 2015

By E. Bane Kroeger

In underground coal mining, there is often a need for supplemental support for mine openings. In the past, one of the most common types of supplemental support was wooden posts that were installed against the roof using opposing wooden wedges. Underground, wood has the tendency to shrink from moisture loss and dislodge if not under load. Another drawback to using wood is the variability in strength between posts. Defects in the wood such as knots can cause weaknesses that often lead to premature failure of supplemental support. Many mines that install large amounts of supplemental support in certain areas of the mine such as bleeder entries in longwall mining have switched to using steel props rather than wood posts or cribbing. The reactions of steel props under loading are well- defined and there is little variability in strength between props. Steel props and can be fabricated so they can be used in a variety of roof heights without modification. Wooden posts often have to be cut to a usable length underground before installation. This adds to the installation time of the wooden posts. Steel props are more compact and can be lighter than their wooden counterparts, depending on the length and carrying capacity. Often times it is desirable to prestress the supplemental support to improve roof stability. This is often problematic and time consuming with some types if supplemental support. With these factors in mind, research was undertaken at Southern Illinois University Carbondale (SIUC) to design a new steel roof prop. Several new clamping designs were developed and prototypes were fabricated and tested in the labs at SIUC in the spring of 2003. The designs were modified and refined and the first full-size prototype roof prop was tested in January 2004. With the success of the full-size prototypes, a cooperative research program was established between SIUC and Excel Mining Systems, Inc. to further develop the new prop. Development went smoothly and the prop has performed as expected. In February 2005, SIUC and Excel entered into an exclusive licensing agreement. The prop design under license, the K-Prop, will be installed using a lightweight portable hydraulic jacking system under design that can be used to prestress the props, applying load to the roof and floor during installation. By varying the installation load, the prestress load can be varied from about 1,000 to 10,000 pounds (4.448 to 44.48 kN) and at the same time, the carrying capacity of the K-Prop can be varied from 10,000 to 100,000 pounds (44.48 to 444.8 kN). The K- Prop is composed of only 3 pieces and laboratory testing has suggested that it can be installed by a pair of workers in less than two minutes. The speed of installation of the K-Prop should significantly reduce the total installed cost for supplemental support and should provide a safer working environment by prestressing the prop, which will add support load to the roof and floor during installation.

Jan 1, 2005

By Renn Oler

Corrosion can often cause significant strength reduction and failure of steel rockbolts, thus demanding continuous rehabilitation and posing challenges to underground mines in maintaining long term ground support. The mining industry has traditionally applied galvanized and epoxy coatings for protection of ground support and reinforcement in corrosive environments due to cost considerations. However, under a harsh and corrosive groundwater condition with extreme pH levels, failure of the existing coated rockbolts often results in failure and falls of the mine roof, especially in long-term mine drifts or entries. To prevent the roof falls induced by corrosive bolt failure, DSI developed a new polymer coating, called ?Obduro AP coating,? to combat harsh and corrosive ground conditions. The new polymer coating was tested in extreme conditions to identify weaknesses and was found to be capable of handling highly corrosive mine water solutions. This paper highlights the challenges faced by underground mines with corrosive bolt failure and shows that the DSI Omega BoltTM can withstand the most corrosive ground conditions when it is coated in the new, economic Obduro AP coating.

Jan 1, 2014

By Alexandra Garcia

A measurement-based ground control management system, commonly employed in coal mines, has been successfully implemented in a UK potash mine operating at a depth of over 800 m. This system includes the routine deployment of telltales in roadways throughout the mine to mitigate against the risk of large-scale roof falls and the deployment of detailed ?design monitoring? instrumentation for ongoing design verification. The routine monitoring systems used in coal mines have not been, to date, commonly applied in potash mines, despite the similar, variable weak geology and associated ground control hazards. Monitoring information from the site indicates that telltales can be deployed to monitor roof conditions, with action levels based on differential rates of strain, as opposed to absolute movement.

Jan 1, 2014

By G. Skybey

The Skybolt is a new bolt concept, point anchored with resin in large diameter holes of specific sizes 38 mm and 45 mm. The new design achieves the optimum annular spacing required for mixing the resin anchor components which is essential for optimum resin bonding of the bolt to the surrounding rock. This paper explains the load transfer mechanisms between bolt/resin/rock, unique to this bolt concept. It compares the pull-out test results to those of paddle and expansion shell type bolts, and highlights the versatility of Skybolt over existing, currently used, rock support systems and the benefits mine operators can achieve when using the Skybolt.

Jan 1, 1992

By G. J. Hasenfus

There are no known published methods of estimating the degradation of coal measure rocks by water that are simple and efficient, yet still provide a quantitative, meaningful value for assessing the stability of coal mine floor, roof, and rib. The slake durability test, the standard index method for estimating the durability of rock subject to wetting, can provide misleading results for floor stability assessment. Additionally, slake durability testing is time consuming and requires specialty equipment. Methods based on humidity cycling have been demonstrated to be very effective for assessing coal mine roof, but require specialty equipment and do not address floor stability concerns. Visual observation techniques, such as that developed for the Coal Mine Roof Rating (CMRR) method, adequately qualify rock degradation, but lack quantitative rigor. This paper will describe an alternative method, coined the water sensitivity test, originally developed for floor stability analyses, but also found applicable for roof and rib stability assessment. The test was developed by CONSOL in the early 1990's, and in its current form, has been in use for approximately twelve years. The method is based on the basic slake durability principle of measuring the mass of the rock retained on a screen after submersion in water. The new test employs two screens of different sizes, and also uses modified submersion, drying, and data processing procedures. The method is relatively efficient and can be geared toward batched testing. As with the slake durability test, the resulting index value provides a quantitative measure of the susceptibility of rock to water degradation. In addition to discussing the test method and its development, this paper provides a comparison of results with those fiom standard slake durability tests, and tabulated results for various types of coal measure rocks. Examples of the technique's utility are provided, including assessment of longwall and development floor conditions, roof and rib rock weathering and stability, and drum-bit cutability.

Jan 1, 2005

By Tom Vandergritft

With advances in system design driving higher productivity, safety, and coal recovery, highwall mining is becoming an attractive option for extending reserve life at surface mines. Typically, highwall mining is performed by contract, with the system owner charging the mining company on a per ton basis, plus a mobilization fee. For this arrangement to benefit both parties, geotechnical planning is required to minimize risk to highwall mining personnel and equipment, while maximizing coal recovery. This paper discusses how highwall mining has been successfully implemented at a large surface coal mine in Colorado, including design procedures, operational factors, and productivity. The operation includes an area where four seams are mined in succession from the lowermost upward, requiring careful attention to seam interaction issues.

Jan 1, 2005

By Joe E. Bryan, John P. McDonnell

"Underground mine rib stability is an ongoing safety issue in all mining applications. Rib-related accidents present at least as many problems as roof-related ground control. Underground coal mine rib safety is continually emphasized as a primary safety concern at every mining operation. The application of rib support materials is increasing as more difficult mining conditions are experienced due to deeper cover, more variable depositional environments, thicker seam heights, and multi-seam mining effects. As the coal seams become thicker, the need for rib control increases. A variety of rib control methodologies has been documented and research continues on mine design methods and support techniques to reduce or eliminate rib-related accidents.This paper presents an alternative rib bolting technology using proven conventional rib support systems that allows mine personnel to more efficiently install rib support during development operations. This alternative rib bolting method allows for additional rib support with a single support installation.INTRODUCTIONRib control continues to garner the watchful eye of both concerned operators and government officials due to many factors: inherent safety within entries and crosscuts, actual rib stability history, safety improvement, cost control, improved mining methods, and maintaining production goals. As demonstrated through many years of actual practice, desired outcomes can be achieved by scrutiny, innovation, and combining improved practice methodologies.Rib surface control continues to be a necessary part of the production process. However, production and safety issues persist at the point of installation using current control apparatuses and methods to install rib controls. Among others, current issues of rib control are quantity of bolts required, overall time required for installation, ease of apparatus installation, flexibility of the system for appendage installation and operator exposure. A need exists to decrease the time miners spend installing rib control apparatuses, while increasing the safety of such installation processes. At present, installing rib control devices (primary rib bolts, plates, mesh, and, in most cases, secondary rib bolts and plates) is performed in a very congested area and is time-consuming process at the primary coal-winning area: the face. The MatLok system addresses these problems."

Jan 1, 2015

By Don Berger

Highwall scaling, bolting and technical blasting are important aspects in the remediation of existing highwall exposures. Proper planning, design and research are important first steps in the development of long term stability. Research into old workings and their influence on highwall stability control the planning and design. These steps are followed by improvements in blasting techniques, highwall monitoring programs and constant evaluation of the results. Recently, due to a number of factors, the highwalls of the Open Cut Mine have started to deteriorate, creating both operational and potential safety problems. Geologic setting, highwall design, mining operations, old workings and weather have combined to create adverse conditions that have allowed sections of the highwalls to become unstable. Homestake Mining Company has developed a program to alleviate the existing ground control problems and to decrease the effect operations has on future highwall stability.

Jan 1, 1996

By William R. Kohl, Craig B. Clemmens

"Since 2010, North Central Resources, Bridgeport, WV, has been using the sonic log to estimate the rockmechanics properties of the coal and adjacent strata in their exploration drilling program. In 68 out of the 85 boreholes they have drilled since 2010, they have conducted shear wave analysis on sonic logs run in these boreholes. By incorporating the rock mechanics logs into the geological model of the coal seam, the engineers can develop a better understanding of the support requirements for the mine.WellCAD Borehole processing software provides vastly improved efficiency in analyzing shear waves from borehole sonic data than previously available methods. The calculation of most rock mechanics parameters requires knowledge of the density and both the compressional wave velocity and the shear wave velocity. Density logs are well known and an industry standard. Sonic logging is equally well known, although less frequently used, as an accurate source of compressional wave velocity. Shear wave velocity is difficult to measure in a geophysical log, but can be estimated from digitally recorded wave form records. This is a time consuming manual procedure which requires the visual examination of thousands of individual wave forms.WellCAD allows the viewing all the wave forms on a VDL display. The observer can create a pair of false logs by manually tracing the interference points on the display for each receiver. He can check himself by observing wave forms in the traditional format. He can then create a shear wave transit time log or “Delta-S” log by subtracting the false log from the near receiver from that of the far receiver. This can be plugged into standard formulae to generate curves for most standard rock mechanic parameters, including bulk modulus, shear modulus, Young’s modulus, and Poisson’s ratio.While these parameters do not entirely substitute for destructive testing, they are extremely cost effective. An entire borehole can be analyzed for the cost of a single destructive test. This allows for a more judicious use of destructive testing while permitting the extension of test data into the rock mass with much greater confidence."

Jan 1, 2015

By Jiachen Wang

China is the largest coal producing country in the world. Coal is widely distributed in China and thus the mining conditions are complex and diverse. This paper summarizes the important achievements in the last 20 years in various mining methods including the extra thick seam with large mining height top coal caving, the thick seam with large mining height and top coal caving mining, the steep seam with top coal caving and fully-mechanized mining, the thin seam automated mining, and the backfill mining. At the same time, the rapid advance in the development of mining machinery and manufacturing has also contributed to the advancement of coal mining technology and the great improvement of coal mine safety. The future direction of China?s coal mining is to further improve mine safety as to improve the coal recovery rate, promote the pillar less mining technology, develop high-efficiency backfilling technology, develop steep seam high-efficiency mining technology for seams less than 10m thick, and high recovery mining techniques for extra thick seams, improve the reliability of mining equipment, and strengthen the protection and restoration of surface environments and water resources.

Jan 1, 2014

By Stankusm John C., Xiaoting Li

"Quantitatively identifying the load on a steel king beam set is a complicated issue in designing the king beam structure at the slope bottom area. From an engineering perspective, understanding the nature and support mechanism of the king beam structure as a standing support is critical in identifying the calculation input parameters for the structure design software. Based on design practices in recent years and successful applications in several slope bottom intersections, the authors present a king beam design methodology, including qualitative analysis, quantitative calculation with a structural design software, and computer Finite Element Analysis (FEA) verification.Especially important is the concept of interaction and the confinement effect between the king beam structure and surrounding rocks, which is essential in designing a proper steel structure in terms of maintaining the roof stability, as well as saving the steel materials and costs of manufacture, labor, and delivery. This paper details the design methodology and applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.INTRODUCTION AND DESIGN METHODOLOGYCurrently, the load on a square or arch set is typically determined by either past empirical design experiences or known heights of roof falls in current or adjacent mines. These methods work but sometimes are too conservative from an engineering perspective. For example, when designing a king beam structure for an intersection, these methods may lead to a design with extremely large and heavy steel beams, which are not convenient for delivery and installation on-site, not to mention, costly. Therefore, accurately identifying the potential maximum load on the king beam structure is important for designing a safet, effective, and cost-efficient steel structure. Based on past several years’ practices and fundamentals of ground control and structural design engineering, the authors propose a design methodology including the following components:The nature and mechanism of effective roof support (qualitative analysis),Ground reaction curve,Interaction and confinement effect between bolts and steel standing support and surrounding rocks,Factors affecting the load conditions of the king beam set"

Jan 1, 2018

By Jingyi Cheng

Many longwall panels in China are laid out along the dip direction such that the direction of longwall retreat mining is along the strike direction of coal seams. Downward mining longwall panels in steeply inclined seams refers to those that are laid out in a non-uniformly developed fold structure where the seam is not only steeply dipping, but also highly undulated along the strike direction, causing longwall mining extremely difficult because it has to deal with large dip angles that vary both in the mining and faceline directions. Obviously, the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply dipping seams have unique patterns that are very much different from those cases of mining the flat or gently inclined coal seams. The effects of those unique patterns presented a big challenge to production and safety. Almost all previous and current researches on ground control have been concentrated on issues related to the flat and gently inclined coal seams. Conversely, research on steeply inclined coal seams, especially those with large angle variation both along the seam dip and strike directions is almost none. Therefore, it is very important to initiate a study to better understand the characteristics of mine pressure and overburden strata movement for this special type of geological condition. The objective of this paper is to monitor and analyze the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams, the angle of which varies greatly along both the seam dip and strike directions. The measured data has conclusively demonstrated that the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams are different from those for the flat and gently inclined coal seams. The large downward angles of coal seam undulation along the strike (mining) direction can obviously affect the roof movement and reduce strata pressure. Study in this research showed that appropriately increasing the rate of mining (or face advance) is positive to roof control.

Jan 1, 2013

By Zach G. Agioutantis

The prediction of ground movements due to underground mining using the influence function method is a mature technology, widely used by researchers and planning engineers around the world. Surface strain, either tensile or compressive, is an important indicator of potential impacts on structures such as buildings, bodies of water, pipelines, railway and power lines, and tailings dams. Calculation of static or dynamic surface strains, for varying surface terrains and slopes, should be accurately predicted and be independent of the methodology applied for the calculation. This paper discusses and compares the development of horizontal and ground strains on the surface due to underground mining for different surface topologies (sloping terrain, monitoring lines, etc.) and presents the steps needed to ensure accurate calculations. Examples are given to demonstrate how ground strains can be calculated for one- and two-dimensional gridded surfaces.

Jan 1, 2013