Search Documents

By Bo-Hyun Kim, Steve Berry, Mark K. Larson

"When coal pillar bursts occur, they involve the sudden expulsion of coal and rock into the mine opening. These events occur when relatively high stresses in a coal pillar, which serve as support in underground workings, exceed the critical capability of the pillar. This causes the pillar to rupture without warning. A cleating is a type of naturally occurring joint system unique to coal seams. However, cleatings are pervasive throughout the coal seam and are much more tightly spaced than joints occurring in other rock types. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated 84 coal samples obtained from a Utah coal mine by conducting both unconfined and triaxial compressive tests in order to examine the response to stress as a function of both confinement and orientation between cleat and loading direction. The results of the study show that the confining pressure dictated not only the peak compressive strength but also the brittleness as a function of the major-to-minor principal stress ratio. The spalling limit of the coal estimated by the s-shaped brittle failure criterion appears to be very dependent on the angle between the cleat and the loading direction, particularly at lower confinement.INTRODUCTIONCoal pillar bursts, or bumps, remain a most critical safety concern in underground coal mining, despite significant advancements in engineering controls. As shown in Figure 1, between 1983 and 2014, there were nearly 400 cases of reportable dynamic failure accidents in coal and nonmetal mines, resulting in 20 fatalities, 155 lost-time accidents, and an estimated 48,000 lost man hours (MSHA, 2015). These types of events have been documented for well over 100 years within the American underground coal mining industry. During this time, mining practices and support technologies have evolved considerably, resulting in an overall decrease in the rate of dynamic failure-related injuries and fatalities. Although techniques and practices of mining are highly advanced, coal pillar bursts, or bumps, continue to occur (Mark and Gauna, 2015). If coal is expected to fail in a brittle manner, behavior changes associated with relatively low tensile strength, such as the transition from tensile to shear failure, have to be considered and reflected in the adopted failure criteria. Rock failure in tension takes place at low confinement around excavations due to tensile failure in heterogeneous rocks (Diederichs, 2007). The prospect of tensile-dominant brittle failure diminishes as the confinement increases away from the excavation boundary. Therefore, it is expected that the transition from tensile to shear mode in the failure mechanism occurs as the confinement level changes and conditions for tensile failure are prevented or strongly diminished. In addition, many uncertainties remain because of the highly anisotropic characteristics of coal seams associated with geologic structure and the mining-induced spatial redistribution of stress in coal pillars. Thus, to prevent fatalities in underground coal mining, continuous effort is required to better understand the catastrophic failure mechanisms in coal mines."

Jan 1, 2018

By Kazem Orace, Navid Hosseini, Mehran Gholinejad

"Selection of the optimum support system for underground openings such as tunnels is a complex process. In this paper a new approach, based on a combination of the Analytical Hierarchy Process (AHP) the Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) and the Preference Ranking Organization METHod for Enrichment Evaluations (PROMETHEE), is introduced. For this purpose, the selection process is assumed to be a multi criteria decision-making problem. First different support systems using FLAC3D numerical code, based on technical safety and stability parameters of the tunnel are specified. Then taking economic and performance parameters as the decision criteria by using the combination of Al-IP, TOPSIS, and PROMETHEE the optimum support system is selected. As a real mine case study this approach is used in the main access entry to the C, coal scam of Tabas collieries. Results clearly demonstrate that the proposed support system selection method is more advantageous than other alternatives.INTROD CTIONGenerally, the support system for a tunnel is selected primarily with the aid of design engineers experience. In other words personal judgment instead of intellectual and scientific criteria is mostly the main basis (Oracc. 2005). However since various support systems can be applied in any particular situation, accurate selection of the optimum support method depends on the integration of many technical, economical and performance parameters, and also on the analysis of the intensity of influence by each of the criteria.In this paper an applicable approach for se lection of tunnel support systems based on Multi Attribute Decision Making (MADM) techniques including: Al IP (Orace et al.. 2009a; Saaty, 1980), TOPSIS (Hwang and Yoon, 1981: Yoon and Hwang, 1995), and PROMETHEE (Brans and Vincke. 1985; Brans and Mareschal. 1992) is introduced. As a field study, this approach was applied to tunnel C1 as one of the main entries in the Tabas coal mine which is the major collieries in the central pan of Iran (Hosseini, 2008).Due to the coal seam conditions coal is mined by mechanized longwall mining (Hosseini 2008). This method requires the 58 excavation of several entries some of which will be used for many years and even for the entire life of the mine (Peng, 2006). Therefore the selection of the support system in these entries is·very important in mining design."

Jan 1, 2010

By L. Munsamy

The bulk of primary mining at the Anglo Coal's Bank Colliery was carried out by drill and blast method, in a bord and pillar layout exploiting the No. 2 Seam. Secondary extraction, top/bottom coaling, also took place using both the drill and blast (D&B) method and continuous miners (CM). Extensive mining in this seam resulted in the risk of sterilising the No. 4 Seam reserves. Therefore, multiseam design guidelines established by Salamon and Oravecz (8) were re-evaluated in light of the low safety factors and the low pillar width to mining height ratios of pillars in the No. 2 Seam. Two and three dimensional (2D & 3D) numerical modelling was carried out to quantify and verify the parameters that influence the multiseam mining. The modelling was conducted primarily in two dimensions (plane strain), with 3D models to confirm the validity of the 2D results. A panel risk assessment flow chart was developed to assess the panels with respect to pillar failure and multiseam mining. This flow chart was extended into the evaluation of risk of surface subsidence using the current rock engineering knowledge. The aim of this risk assessment tool is to assess all underground workings at Anglo Coal collieries simply and rapidly. The identification of high-risk areas would warrant further investigation and possible backfilling to reduce the risk of pillar failures ensuring that reserves in the No. 4 and 5 Seams above are intact.

Jan 1, 2004

By Jinwang Zhang, Zhaohui Wang, Jiachen Wang

"Thick coal seams (seam height larger than 3.5 m) account for a large portion of the proven coal reserves of China, and underground thick coal seam mining provides about 50% of the Chinese annual coal production. Such seams are mainly mined using the longwall top-coal caving (LTCC) method. For safe and successful mining, a number of analyses on the stability of surrounding rocks in the LTCC face area have been extensively performed, and certain research achievements have been made. This paper introduces the main findings on rock pressure occurrence in the LTCC face during the last few decades and presents face and roof stability control techniques. INTRODUCTIONUnderground thick coal seams in China provide 1.8 billion tons of coal every year, which accounts for approximately 50% of the total Chinese annual coal production and 25% of the world, indicating that thick coal seams stand an important position in Chinese coal mining industry (Wang, 2005). Before the 1980s, thick coal seams were mined mainly by using the multiple-slice mining method. With the improvement of mining techniques and equipment in last two decades, longwall top-coal caving (LTCC) and high-seam, single-cut longwall are employed for thick coal seam extraction, offering advantages over multiple slicing from entry excavation and production perspectives (Wang, 2013).. The primary author of this paper introduced the most popular thick coal seam mining methods in China at the 30th ICGCM (Wang, 2015). This paper presents the stability of surrounding rocks in face area and ground control techniques for mining thick coal seams. For traditional longwall faces (seam height less than 3.5 m), the well-developed VoussoirVoussoir beam theory has been successfully used to analyze the movement of overlaying strata, which indicates that ground control techniques have become mature for this mining system. In such faces, the four-leg support with loading capacity of 4000–8000 kN is considered adequate for safe and successful mining. These faces normally have an annual yield of 1–2 million tons (Wang, 2007). For thick coal seams, however, the traditional support becomes inadequate and the ground control problem change to be more difficult and complex. Thus, development of large-scale mining equipment and ground control techniques for enlarged mined-out space and entries have been recognized as the most basic technical problems in mining thick coal seams."

Jan 1, 2017

By Kirk W. McCabe

RokLok binder is a two-component polyurethane system consisting of a polymeric isocyanate (Component A) and a polyol resin (Component B). The two chemicals are mixed and injected into the mine rock under pressure. The initial low viscosity enables the RokLok material to permeate many of the smallest fractures. About 3-5 minutes after injection, the reacting material begins to expand in the fractures; the reaction is completed after 1-2 hours, and the material sets to a mechanically strong binder which adheres tightly to the rock. The consolidated rack provides resistance to any further f movement w thin the strata. The RokLok binder injection system is fast becoming an important engineering tool for coping with adverse underground geological conditions. Two case histories discussed in this paper, a longwall mining problem and an entry-roof problem, demonstrate the effectiveness of using the RokLok binder system to help solve complex ground-control problems in a cost-effective manner.

Jan 1, 1981

By S. M. Hsiung

A model (support selection model) for the selection of suitable types of powered supports under various geological conditions is proposed. This model is developed by evaluating the support, performance under different roof conditions at longwall faces in terms of five controlling parameters: (1) roof Falls, (2) front abutment pressure, (3) Face convergences, (4) gob materials entering into working area, and (5) roof caving line. This model suggests that more than one type of powered support. may be used under the same roof condition and the best selection should he based on the magnitude of suitability index of each support- type. The development and application of suitability index arcs discussed. Fourteen panels in seven coal seams are discussed in the paper to illustrate the applicability and effectiveness of this model. A roof classification system at longwall faces developed specifically for the construction of the selection model is also discussed. A simple example fur determining roof classification index is given.

Jan 1, 1988

By Shuangsuo Yang

Coal ribs can roughly be divided into three types: (1) roof and floor rocks are similar to ribs, (2) roof and floor rocks are stronger than ribs, and (3) roof and floor rocks are weaker than ribs. Different types of roof/floor and ribs will exhibit different types of ground pressure around an entry. Most coal mines belong to the 2" type with ribs fractured or even broken. In this case the mine ground pressure depends on the occurrence and development of deformation and fracture of the ribs. If it's not properly controlled, the following deteriorating process will follow: the roof bent downward > the ribs squeezed and broken > rib sloughing and collapse > rib support to the roof reduced > the roof bent downward further > the ribs broken further. In this paper rib instability is divided into four types: compression/shear sliding rib fall, gravity sliding rib fall, cross arch rib fall, and cleavage rib fall. Since failure in thin walls is largely of tension type whereas that of thick walls by compression or shear, a concept is proposed here to utilize a thick bolted rib to stabilize entry ribs, i.e. the thickness to height ratio of the thick bolted ribs

Jan 1, 2005

By A. Chrzanowski

The integrated approach to monitoring surveys is based on a simultaneous utilization of geodetic, photogrammetric and geotechnical measurements of displacements, tilts, strains and any other geometrical parameters of deformation. New techniques for the integrated surveys are being developed at the University of New Brunswick in cooperation with the Canada Centre for Mineral and Energy Technology. A telemetry system for continuous monitoring of geotechnical measurements under difficult climatic and topographic conditions has been constructed and successfully tested in a coal mining area in western Canada. A generalized method for analysing the integrated deformation measurements has been developed and applied in the test area to yield three dimensional empirical modelling of surface movements from geodetic, photogrammetric and tilt surveys. The most appropriate model can be chosen from a statistical assessment of several modelling possibilities. The empirical model of the deformation can be employed in a "calibration" of the prediction (deterministic) model of the ground movements. A computer programme for two- and three-dimensional finite element modelling of elasto-plastic deformations has been developed at UNB as a part of the integrated approach. The :EM has been tested in predicting deformation in the test area in difficult geological conditions which were associated with an extraction of a steeply inclined coal seam. The results gave good agreement with the actual displacements obtained from geodetic measurements and confirmed the existence of a suspected fault.

Jan 1, 1984

By Keith A. Heasley, Christopher R. Newman

"Originally developed in 1993, LaModel has aided mining engineers and researchers alike in improving the design and safety of underground single- and multiple-seam mining operations (Heasley, 1998). Through the years (Heasley, 2011), the use and capabilities of the LaModel program have grown immensely while adapting to ground control concerns and problems within the mining industry. Presently, MSHA specifically mentions the use of LaModel for the analysis of, “complex non-typical roof control plans,” defined as either room-and-pillar retreat mining greater than 1000 feet, bump- or bounce-prone mines, or other criteria considered unusual by the District Manager (Stricklin, 2013).With an ever increasing number of users and an increase in available solution options and complex analyses, there is now a significant demand for better education and training in the practical application and detailed analysis using LaModel. This paper presents the development of an electronic user’s manual and comprehensive online training course created in an open online learning environment in order to better inform and train industry professionals as well as engineering students and new users. The development of both the user’s manual and online training course will ultimately increase the ground control design effectiveness of mining engineers, leading to safer and more productive mine designs.INTRODUCTIONOver the past 20 years, mining engineers and researchers have used the LaModel program for improving the design and safety of single- and multiple-seam mining operations. LaModel uses a laminated, displacement-discontinuity, boundary-element method which simplifies the overburden into a stack of frictionless homogeneous laminations and limits the detailed analysis to the seam itself. This approach is fundamentally simpler than either finite-element, finite-difference, or discrete-element approaches; and, therefore, the program provides a significant reduction in computational time and efficiently calculates the displacements, stresses, pillar safety factors, multiple-seam interactions, subsidence, etc. for thin-bedded deposits such as coal, salt, potash, limestone, etc. (Heasley and Salamon, 1996; Heasley and Agioutantis, 2001). The laminated overburden model in LaModel is different than previous homogeneous elastic formulations and more realistically represents the natural flexibilities of the stratified sedimentary overburden typically associated with coal seams (Heasley, 2008)."

Jan 1, 2015

By Yao Yuping

The strength and deformation of more than two hundred coal samples have been tested in the condition of triaxial compression. The regression equation showing the relationship between coal strength and pressure in the pores as well as confining pressure, was obtained. The appropriate calculation for stress-strain curve was carried out. Further, an analysis shows the variation of coal strength and its modulus of elasticity in methane medium.

Jan 1, 1992

By Adrian L. Moodie

Austar Coal Mine (formerly Southlands and Ellalong Collieries) has had a long association with difficult strata control conditions associated with mining depth and a highly jointed/cleated coal seam. The conditions include poor longwall face conditions, cyclic loading, heavy tailgate (TG) roadway conditions, and difficulties in maintaining stable roadways on development at 5.2 m (17 ft), as well as the geotechnical challenges of an 8.5-m (27.9 ft) -wide roadway required for installation faces. The introduction of Longwall Top Coal Caving (LTCC) to this environment has aided in the management of some of these issues, but LTCC has also given rise to other geotechnical considerations. Additional geotechnical issues associated with LTCC not only require management during operations, but also require consideration when evaluating new mining areas at Austar Coal Mine or potential LTCC extractable resources throughout Australia and the world. In September 2006, LTCC commenced at Austar Coal Mine in longwall panel A1. Since this point the LTCC face has been increased from 147 to 216 m (482 to 709 ft)and finally to 227 m (745 ft) in width, and it has also been rehanded and modified in the three fully extracted panels to date. The application of LTCC in panels A1, A2, A3, and now A4 has been very successful, both from a coal resource recovery point of view and in the management of the principal hazards of spontaneous combustion and strata control. This paper focuses on the geotechnical aspects of the application of LTCC at Austar Coal Mine and also reviews some advances in general strata control management at the mine.

Jan 1, 2011

By Phillip E. Gramlich

Through extensive practical experience and multiple studies, tensioned roof control systems have proven beneficial in difficult mining conditions. Due to increased mining of less desirable seams, tensioned roof control systems have claimed a progressively larger share of the total number of roof bolts installed in the US coal industry. Each tensioned roof control system has its benefits, but also has problems concerning cost, cycle time, stress concentration, load retention, and protrusion into the mine opening. For example, resin-assisted mechanically anchored bolts (also known as resin point anchor bolts) have a fast cycle time and the potential for high tension loading, but the stress from the mechanical shell is concentrated in a small area and can create concerns with certain roof structures (Zhang and Peng, 2001). Resin point anchor bolts can be difficult to fully grout. The cost of resin point anchor bolts can be an issue; a two-piece resin point anchor bolt has a large number of parts (10) and manufacturing steps (9), adding to its higher cost. Tension rebar bolts can achieve high loads and are easier to fully grout but have longer cycle times. In addition, a high percentage of the installed load can ?bleed off? if the resin mixing time or the ?hold time? before tensioning is short-circuited. Tension rebar bolts can be notorious for protruding into the mine opening, creating an obstruction for man and machine (Figure 1), in particular, with reduced mining heights. A new tensioned roof control system has been developed that doesn?t have moving parts, is cost effective, provides fast cycle times, has a low profile, and is simple t install.

Jan 1, 2014

By Wojciech Masny, Andrzej Walentek

"The most common extraction method in Polish coal mines utilize pillars between adjacent longwall panels. This is mainly due to the significant depth and difficulties in maintaining stability of the gateroads. This paper presents measurements of entry convergence and range of the fracture zone around a gateroad measured with a borehole camera. The entry where the measurements were taken was located in a parallel entry separated from the gateroad by a 5-m- (16-ft-) wide pillar. The gateroad was located in a hard coal seam 900 m (2,952 ft) deep with a dip of 5°. The extraction method was longwall mining with caving and the mining height was about 3 m (10 ft).Furthermore, the ""in situ"" measurements were compared to the convergence forecast for the gateroad and fracture zone by means of numerical modeling conducted using the Phase2 Version X.X finite element program from Rocscience. The determination of the fractured zone around the openings is of great importance to successful mining practice, especially in support planning and design for longwall gateroads. Moreover, proper determination of the fractured rock zone is one of the basic elements in the process of planning the roof bolting for mine workings.INTRODUCTIONIn the Polish. hard coal mining sector, retreat longwall extraction is most commonly used (Prusek and Masny, 2007). This method is connected with the necessity to carry out a number of development operations during the first stage, including among others, driving of gateroads and a setup room.Currently, most Polish mines eliminate gateroads behind the extraction front, using the ""U"" ventilation system (Szlitzak et al., 2008). In such cases, one of the roads for the next longwall panel is driven along the caving goafs, leaving a protective pillar of some chosen width (Figure 1). The question regarding the width of the coal pillar is especially important to the stability of the gateroads that define the panel for the subsequent longwall. When analyzing the previous experience relating to this type of pillar (Junker, 2006; Rajwa, 2008; Stranzet et al., 1973; Betriebsempfehlung, 1982), one can state that there exist two solutions for the determination of its width."

Jan 1, 2010

By Lightfoot. Nicholas, Na Liu

"Mining in multi-seam workings has been undertaken for many years in the VK Remnant pillars above and/or below current working areas have an important influence on retreat gateroad conditions at five of the remaining six deep coal mines. These interaction effects need lo be predicted ahead of mining so that longwall panels can be positioned to minimize roadway damage and to identify areas where additional support should be installed early into competent strata when and where it is most effective.Currently, three-dimensional elastic stress analysis using MAP3D is undertaken to predict local vertical and horizontal stress magnitudes during gateroad development and in front of the face on retreat. The predicted stress fields are often used as input to FLAC for roadway modelling.Using Maltby Colliery in South Yorkshire as a case study, this paper illustrates the MAP3D approach, together with its current limitations and uncertainties. Possible future improvements in the analysis method are proposed and the authors would welcome comments on these, or suggestions for alternative approaches.MODELLING OF MULTl-SEAM LAYOUT & MULTI-SEAM INTERACTIONThe remaining large coal mines in the UK arc operating at depths of 800-1, 150 m (2,625-3,773 ft). Production panels are now mined on retreat after the accompanying single entry access roadways have been completed. These gateroads are typically supported with a system of steel rock bolts and cable in the roof and steel bolts and glass re in forced polymer (G RP) dowels in the sidewalls.In addition to new panels being mined in the vicinity of old goafed districts, a significant amount of extraction has usually already taken place in coal seams above and/or below the current working areas. This means that there is also interaction between the current workings and the remnants of the old workings in other seams. As a consequence of the mining methods employed, old workings can have a complex geometry compri ing collapsed and partially collapsed excavations intersper ed with small and large pillars of unmined coal. The unmined coal pillar act as stress concentrators that carry the overburden load while the mined out excavations create stress shadows of varying degrees depending on how much collap e and reconsolidat ion has occurred. This is illustrated by a simple elastic model as shown in Figure I."

Jan 1, 2010

By Srisharan Shreedharan, Gang Huang, Hongqing Song, Sijing Cai, Pinnaduwa H. S. W. Kulatilake

"Subsidence prediction due to ore extraction and backfilling during open stoping operations for an underground iron mine in China is reported in this paper. Geologic complexities including faults and interfaces between different lithologies, and the stoping and backfilling sequence adopted from the mine plans are incorporated in building a 3-D discontinuum numerical model. The stoping was simulated in two vertically stacked horizontal layers (Fig. 6), with a total of 16 stopes. Large displacements of up to 50 cm were predicted by the model along the roof of the stopes, and a maximum surface subsidence of 22.5 cm was predicted by the model . Backfilling was found to control subsequent deformation and subsidence. The extraction of the upper orebody led to relatively higher deformations in extracting the lower orebody. Finally, the predicted subsidences at all locations along a subsidence profile on the surface are shown. INTRODUCTIONThe Luohe iron (pyrite) mine, located in Hefei city, Anhui, is an underground mine in China, being mined through the open stoping and backfilling method. The orebody lies at a depth of about 400 m and has an average thickness of 250 m (Magang Steel Company, 2012a). Discovered in the 1960s, the location has a reserve estimate of 300 million tonnes, which have been mined since 2007. The orebody has been divided by the mining company into an east and a west section to facilitate planning for ore extraction.Figure 1 shows the surface above the underground mine, which is seen to contain many human settlements including villages, pastures and other infrastructure. These locations are sensitive in that they need to be protected from potential adversities due to the underground mining, such as surface subsidence. While it may be near impossible to completely eliminate the subsidence due to ore extraction, operations such as backfilling have been adopted by the mine in an effort to substantially reduce it. Hence, this paper focuses on describing the stability of stopes in the mine and estimates future subsidence in a part of the mining region through numerical modeling."

Jan 1, 2016

By Thomas R. Scotese

A rock mechanics instrumentation and monitoring program was implemented during pillar extraction at Gulf Mineral Resources' Mt. Taylor Mine, the deepest uranium mine in the U.S. Three types of monitoring were employed: (1) drift convergence around stopes (using a portable tube extensometer), (2) stress changes in pillars (using vibrating wire stressmeters in horizontal boreholes), and (3) load changes in haulage ways under stopes (using vibrating wire load cells in jack stands). Results include convergence-time graphs, convergence contour maps, stress-time graphs, a stress increase contour map, load-time graphs, and abutment load limit maps. Major factors influencing results include (1) size of pillars around the extraction area, and (2) presence and orientation of a major fault adjacent to one extraction area. These factors, combined with pillar extraction, produced evidence of load transfer over 120 m from a stope measuring only 55 m x 45 m. Vertical stress increases of 7 to 17 MPa (1000 to 2500 psi) within 60 m of the stope were obtained using the stress- meter manufacturer's method. The fault apparently prevented load transfer in the down-dip direction but increased load transfer in the up-dip direction. Convergence rates of up to 1.3 cm/day (0.5 in/day) were measured at two stations. Instruments were generally reliable despite adverse underground conditions. The instrumentation and monitoring program at Mt. Taylor provided a warning system against ground control problems and a characterization of ground behavior for future development and extraction of pillars. Recommendations are made for future mining and instrumentation practices.

Jan 1, 1984

By Guy Reed, Russell Frith, Kent Mctyer

"Coal pillar design has historically been based on assigning a design factor of safety (FoS) or stability factor (SF) to coal pillars according to their estimated strength and the assumed overburden load acting on them. Acceptable FoS VALUES (have been assigned based on past mining experience, and at least one methodology includes the determination of a statistical link between FoS and probability of failure (PoF).The role of the pillar width-to-height (w/h) ratio has long been established as having a material influence on both the strength of a coal pillar and its potential mode of failure. However, there has been significant professional disagreement on using both FoS and w/h ratio as part of a combined pillar system stability criterion, as compared to using FoS in isolation. The argument is that, as w/h ratio is intrinsic to pillar strength, which, in tum, is intrinsic to FoS, it makes no sense to include w/h ratio twice in the stability assessment. At face value, this logic is sound.However, this paper will argue that there is a valid technical reason to bring w/h ratio into system stability criteria (other than its influence on pillar strength), as it is related to the post-failure stiffness of the pillar, as measured in situ, and its interaction with overburden stiffness.When overburden stiffness is bought into pillar system stability considerations, two issues emerge. The first is the width-to-depth (W/H) ratio of the panel, in particular whether it is sub-critical or super-critical from a surface subsidence perspective. As a minimum, this directly relates to the accuracy of the pillar loading assumption of full tributary area loading. The second relates to a reevaluation of pillar FoS based on whether the pillar is in an elastic or non-elastic (i.e., post-yield) state in its as-designed condition, as relevant to maintaining overburden stiffness at the highest possible level.The significance of the model presented is the potential to maximise both reserve recovery and mining efficiencies without any discernible increase in geotechnical risk, particularly in thick seams and higher depth of cover mining situations. At a time when mining economics are, at best, marginal, removing potentially unnecessary design conservatism without negatively affecting safety is of interest to all mine operators and is an important topic for discussion amongst the geotechnical community."

Jan 1, 2016

By Saeed Zandi, Kazem Oraee

"Tunnels and galleries are the most important structures in coal mines. They are used for variety of purposes, such as transporting ore and people and for ventilation. A well-designed support system is necessary to stabilize structures and prevent collapse.Using rock bolts increases the strength of the rock in which tunnels are made. Rock bolts are used extensively in most underground mines today, and coal mines are no exception. Almost all galleries in a typical coal mine use some type of rock bolt, at least, as a means of partial or supplementary support.In this research, changing the support system from expensive methods to the use of rock bolts as the primary means of support is discussed, with the focus on a particular gallery in Hejdak coal mine. Visionary design methods, in conjunction with rock mass classification schedules, were used to determine an optimal rock bolt pattern. For this purpose, rock mass rating (RlVIR) and quality index (Q) classification systems were used. Several empirical methods were also used to design an optimal pattern for rock bolt installation in the particular tunnel under analysis.As such, the tunnel support system was designed using both finite element and empirical methods. Finally, the results obtained from both numerical and empirical methods were compared under different load conditions. The methodology prescribed in this paper, together with the comparison, can be a useful tool when selecting a support system. The results can also be used to design a support system in this and any other coal mine with similar conditions.INTRODUCTIONSince the advent of underground excavation techniques, one of the biggest challenges has been stabilizing tunnel walls and preventing roof collapse in tunnels and other underground openings, such as galleries. Loose rocks and layers drop into tunnels and galleries, except in very hard rock. Underground roof collapse and falling rocks can have devastating effects on the safety of operation personnel and equipment and can seriously affect production. When designing an underground coal mine, the stability of tunnels and galleries is an important parameter that should be studied carefully because it has an important role in the production process of the mine. Therefore, an appropriate and well-designed support system is necessary for preventing collapse and helping to stabilize the tunnels and galleries."

Jan 1, 2016

By Xuexin Ding, Weijie Wei, Jinwang Zhang, Yi Chen, Shengli Yang

"Many ultra-thick coal seams exist in Xinjiang and the northern part of the Inner Mongolia. These coal seams are more than 30-40m thick. This kind of the thick coal seam is too difficult to extract in one slice, so the top-coal caving longwall mining method was designed for this purpose. In order to study the movement characteristics of the overburden strata and the development of the ""three zones"" in ultra-thick coal seams, the physical and numerical simulations were carried out based on the in-site condition of Baiyinhua coal mine. The result shows that, when extracting the upper part of the l 5m thick coal seams, the first weighting interval was 50-58m and the periodic weighting interval was I 8-20m. The caving zone, fractured zone and bending and sinking zone were 38m, 92m, and 50m respectively in height. The fractured zone height increased with the advancing distance of the face, but in some localities, a ladder-like distribution due to the periodic weighting existed. When extracting the lower part of the 25m thick coal seams, the roof was extremely broken and the collapse range of overlying strata continued to increase in irregular form.INTRODUCTIONThe thick coal seams occupy 44 percent of coal reserves in China and account for 45 percent of the gross domestic coal production. There are three main methods for extracting the thick coal seams: sublevel mining, large height mining, and longwall top-coal caving (LTCC) (Wang, 2009). Due to the rapid development of LTCC in the past two decades, it has become the most extensively used mining method. It possesses the advantages of high-production, high-efficiency, low development ratio, and low-cost (Yang, Zhang, Chen, and Zhengyang, 2016; Wang and Zhang, 2015). Baiyinhua coal mine's coal reserves are full of uniformly distributed thick coal seams, with the minable thickness of the main coal seam between 25 to 40m, i.e. the main coal seam is an ultra-thick coal seam. Sublevel longwall top-coal caving (SLTCC) which is an efficient method for extracting the ultrathick coal seams has led to multiple disturbances Xie, Chen, and Wang, 1999; Singh and Singh, 1999; Xie, Chang, and Yang, 2009. Therefore, using the case of Baiyinhua coal mine, the movement features of overburden strata and development characteristics of the three zones in ultra-thick coal seams were studied by physical and numerical simulations (Qian, et al, 2003; Qian, 1994)."

Jan 1, 2016

By Joel Bradley, Kot Unrug, Kyle Perry, Mark Klimek

"A West Kentucky mine operation in No. 11 seam, encountered floor heave, due to the localized increase of the thickness in the fireclay mine floor. Floor heave has overridden seals installed in two mined out panels. The third seal’s location was planned for isolating that area from the Mains. A plan of support has been developed to prevent repetition of the floor heave and related problems outby the seals. The applied ground control measures were successful. An attempt of a 3D numerical modeling was made, that it would match the observed behavior of the mine floor and could be used as a design tool in similar conditions. In the paper described are sequence of events, a mitigation ground control system applied, and the first stage of numerical modeling.IntroductionWest Kentucky coal mine operation in the No. 11 seam has approached an area where the fireclay floor thickness increases to about 5 ft. Delayed floor heave has been observed. In the first sealed area (Panel KK), floor heave has overridden the seals and has begun to progress outby. This could not be allowed at the new seal location PP described in this paper because such override would affect the mains. Previously numbers of standing support systems were used, but their effectiveness was not satisfactory as is illustrated in Figure 1, Figure 2, and Figure 3. Therefore, with sealing of the next area approaching, mine management was looking for a better solution that would eliminate the problem. In that stage, our team looked closely at the geology and strength of roof and floor, as well as the characteristics of ground failure around the seal at the first site. The technical literature has been searched as well Haramy et al. 1986 Hsiung and Peng 1987, Peng 2008, Santos & Bieniawski 1987. This led to the identification of factors responsible for the ground failure. It has been determined that increased fireclay thickness from typically less than 2 ft to about 5 ft, when compared to the previously mined parts of reserve, and the strong limestone strata just above the immediate roof composed of 2 ft of black shale, created conditions of failure. It appeared that, when pillars were punching into the mine floor, the strong roof did not break but was bending, exerting high pressure on outby pillars, causing rib failures and closure. This is a similar mechanism to a strong roof affecting longwall shields. The remedial action planned was additional support."

Jan 1, 2015