Search Documents

By Ulrich Paschedag

The WESTFALIA group of companies developer and manufactures underground mining machinery for complete high-performance longwalls. WESTFALIA uses a state of the art electrohydraulic system as the most important component for the realisation of today's fully automated plow or shearer longwall. The shield control unit (SCU) allows maximum custom designed software flexiblity as well as maximum hardware reliability. The master control unit (MCU) monitors shield support data as well as the plow/shearer position. By using an industry standard PC in an explosion-proof box with an intransically safe keyboard nearly unlimited software capabilities can be obtained with inexpensive hardware. Among various other modes of operation this MCU allows the monitoring and recording of data which can be transmitted to a surface computer. Production and operational adjustments can be made by the mine management based on the MCU information. Statistical analysis of the distribution of roof pressure under various conditions is also possible. The WESTFALIA automation system PM-4 gives the operator maximum flexibility and helps the mine management to run their longwall more efficiently and safely.

Jan 1, 1994

By G. C. Sun

Rock mechanics properties, i.e. uniaxial and triaxial compressive strength, indirect tensile strength shear strength, Young's modulus, and poisson's ratio were collected for coal and related strata from 50 coal seams in 90 mines. The methodology of data organization and retrieval is described in details. The values and .ranges of those properties are also discussed.

Jan 1, 1993

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By Gennaro G. Marino

Documented case histories of surface ground movements from mine subsidence were utilized to help determine when the initial collapse of the overburden occurred above longwall panels. By studying this relationship between initial movement at the surface and the amount of face advance, the least-complex conditions exist for empirically assessing the span capacity of the overburden. The objective of this work was to obtain a better understanding of the overburden response to longwall mining. This knowledge will give a better insight on the long-term effects that different overburden types have on the stability and the subsidence potential of room and pillar mines, as well as, the influence of the overburden on subsidence over longwall panels. Theory on the overburden span capacity was developed and correlated to field observations. Data were used on the overburden lithology, depth, width, and face advance of the panel, and the subsidence conditions that were noted on the surface. The subsidence measured on the surface was used to determine when complete failure in the overburden rock had occurred. According to spans predicted by theory and the subsidence measured in the field, the competent lower units failed at a face advance less than when significant subsidence was observed on the surface. In each case studied, there were competent lower beds; however, the full overburden weight was not sustained to the point of subsidence. The best correlation with the surface movement was found with the most shallow, competent bed. Elastic plate solutions with various support conditions were found to best monitor the surface subsidence of these upper roof units.

Jan 1, 1988

By Karsten Zimmermann

Surface deformation monitoring is required all over the mining industry. For example oil and gas companies need this information to support exploration and production activities and to detect impacts from surface subsidence of existing hydrocarbon fields. Also opencast mines require large area information of subsidence due to dewatering of the overburden. Because of this, a lot of surface deformations measurements with GPS or traditional geodetic measurement techniques have been conduced during the last decades. This paper presents the actual capabilities to analyze GPS data using the state of the art Bernese GPS Software for GPS post processing. A new way of monitoring subsidence is a combination of GPS and satellite InSAR data. Considering this it is hoped that a combined strategy will permit receiving overall more information by integrating high point density of InSAR and accuracy of GPS. DMT is one of the leading actors on GPS services especially for monitoring surface movements from underground activities e.g. mining, water pumping or oil and gas exploitation. The paper will discuss preferences and problems of this approach on results of a current project of DMT.

Jan 1, 2008

By H. Guo

There are a number of methods available for the determination of the fracture toughness of rock. Some of the most recognised methods include the hollow pressured cylinder, the short-rod, the chevron - edge-notched round bar in bending and the disc-shaped compact specimen. Most of these tests are difficult and expensive to conduct. In this paper the simple Brazilian testing of discs for tensile strength has been used to determine their fracture toughness. Tests were conducted on six different rock types and the values of the fracture toughness obtained for each type are in close agreement with the results of the well recognised the chevron edged types. Details of the tests, and analytical validation of the technique, are presented

Jan 1, 1992

By Anthony T. Iannacchione

Underground bituminous coal mining is a large and significant industry within the Commonwealth of Pennsylvania, and it has a legacy of environmental consequence. For example, in 2008, 13.5 acres (5.5 hectares) of land were undermined by longwall mining every day. Laws and regulations have been promulgated requiring companies involved in this industry to remedy mining damage caused to homes, businesses, and land; replace impaired water supplies; and repair impacts to streams and wetlands. The regulations and technical standards set by the Pennsylvania Department of Environmental Protection (PA DEP) have been put in place to assure that coal operations comply with ACT 54 of the Bituminous Mine Subsidence & Land Conservation Act and other related legislation. These regulations and standards require operations to address impacts when a mining permit is submitted and as permits are modified and extended. One of the special provisions of ACT 54 is the requirement by the PA DEP to produce an assessment of the surface impacts of mining every five years. The University of Pittsburgh was contracted by the PA DEP to perform the 3rd assessment, which spanned from August 21, 2003, to August 20, 2008. This paper details the findings related to surface structure undermined during this period. A total of 3,735 structures were tracked. Four-hundred-fiftysix reported effects were found, and each required additional information and analysis. The majority of the reported effects were associated with eight longwall mines. Characteristics of the structures were analyzed and discussed, with special attention to those with reported effects. The number of undamaged and reportedly damaged structures (i.e., dwelling, barn, commercial building, etc.) undermined during the assessment period were listed. Lastly, the resolution status and type of resolution were analyzed for all structure reported effects.

Jan 1, 2011

By B. G. D. Smart

An understanding of the nature of yield zones surrounding coal mine excavations is fundamental to the design of mine support systems. Various methods have been designed for investigation of underground rock masses and an extensometric technique, the Magnetic Rod Extensometer, has been developed to overcome inherent design limitations in existing equipment of this type. This paper refers to the prototype form of the extensometer and details changes designed to overcome a variety of drawbacks indicated by routine use of the equipment. The principal change has been one of manual to computerised data acquisition and presentation in the laboratory phase of the system. This has dramatically reduced the time taken to process underground measurements and produce numerical and graphical results. The revised Magnetic Rod Extensometer represents an integrated instrumentation system that combines speed and accuracy in all areas of data handling.

Jan 1, 1984

By Clive Chadbourne

Investigations of world wide coal face strata control practice, the study of theoretical calculations and detailed engineering analysis have been combined to design and select a powered roof support suitable for use in conjunction with the extraction of 4.5-m (14.7- ft) of the 7.5-m (24.6-ft) thick Warwickshire Thick Coal Seam. The interface between geotechnical criteria and engineering design has been closely considered along with the following 3 important factors: Firstly, the need to further improve strata control and operational characteristics whilst producing a wall integrated overall face design. Secondly, to enable the supports to be rapidly transported from face to face in roadways driven at the minimum size for operational requirements. Finally, to provide hydraulic power, automatic control and monitoring systems which will improve operations reduce manpower requirements and improve management information. Clear design requirements were determined in order to allow selection on a commercial basis. A method of tendering is described with the subsequent analysis and selection process. In the event oversupply of coal in the UK resulted in the order not being placed. Brief consideration has been given to supports suitable for reserves to be mined In a few year's time where there is potential for extraction well in excess of 4.5-m (1 4.74.

Jan 1, 1994

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By Jiulong Cheng

Underground coal mining causes overburden deformation and failure, one major form of which is bed separation in the overburden. Surface subsidence can be controlled by injecting grout into the bed separations. For a long time, the grouting results of bed separation can not be validated. This is the problem in the application of this technique. This paper analyzes the conditions leading to bed separation, develops mathematical models for seismic wave fields generated before and after bed separation, and bed separations grouted with different materials, and computes the seismic wave field characteristics using the finite difference method. The results show that the existence of bed separation causes changes in the characteristics of seismic wave field, and that different grouting materials generate different seismic wave field characteristics. Intact strata, bed separation, and bed separation filled with air or water all display distinctive seismic wave field in amplitude and frequency spectra. After mining, the original location that provides strong seismic reflection wave no long exists. It is replaced by a weak and syncline-shaped reflection wave. The area, where the seam wave disappears, is larger than that of the mined area. The location, where a bed separation occurs, generates a set of reflection waves stronger than the normal one. The energy of the reflection waves varies with the materials filling the separations. Bed separations filled with air generate stronger reflection waves than those filled with water. The major frequencies for those filled with air are lower than those filled with water. Therefore, it is possible to determine the property of filling materials by analyzing and comparing the amplitude and frequency spectra of the reflection waves. Case studies of application of seismic method for exploring bed separations and grouting were analyzed. The results show that it is feasible to use seismic technique for exploring bed separations and grouting.

Jan 1, 2006

By A. W. Khair

This paper deals with the analysis of pillar failure in a room and pillar mining operation of a deep underground coal mine. The incident here involved the failure of more than 100 pillars. The mechanism of pillar failure (bump/squeeze) has been studied in detail. The analysis consists of inmine eyewitness observations, laboratory experiments and analytical study of the pillar failure area using finite element technique. Results indicated that the mechanical properties of coal, roof and floor, geologic condition, and the method of operation have affected the mode of pillar failure. Hard roof and floor prevented roof caving and floor heaving in the gob area creating an inhomgeneous stress field on the pillar. This condition developed a yield zone and a core zone in the pillar. Progressive increase of vertical stress further increased the yield zone of the pillar and reduced the core pillar leading to a total squeeze of the pillar. However, the analysis indicated that the pillars were liable to bump provided any sudden shift of load occurred on the core pillar due to some dynamic shock imparted by a local failure of the immediate roof (slickenslided area) or during splitting.

Jan 1, 1986

By E. D. Doney

The Kerr-McGee Coal Corporation's Galatia Mine's first longwall mining system was implemented on May 3; 1989. Start-up of the longwall face represnted the successful conclusion of an effort begun nearly four years earlier. This paper-presents a case history of the processes that led to the longwall's implementation, and the subsequent mining of the first 7,900 foot long panel.

Jan 1, 1990

By Ken Mills

A program of stress change and roadway deformation monitoring was undertaken to measure the forward abutment load distribution about a retreating longwall panel at Dartbrook Mine. The results of this monitoring allow roadway conditions observed at various stages of mining to be ranked according to the estimated vertical stress they have experienced. This ranking also provides a means to predict and visualise future roadway conditions at various stages of mining. This paper presents the results of the monitoring and describes the approach developed to predict future roadway conditions. The monitoring results show the vertical stress distribution associated with the front abutment from a longwall goal decreases exponentially away from the goaf edge. The vertical stress distribution peaks at the goaf edge at 5 to 6 MPa stress increase and decreases to 1 MPa within 50 m becoming imperceptible beyond 100 m By scaling this measured distribution to reflect the loading environment, the vertical stress can be estimated for different overburden depths and different stages of mining. Photographs of roadway conditions at particular vertical stress levels provide a way to visualise roadway conditions at various stages of mining in the future

Jan 1, 2000

By Gabriel Esterhuizen

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

Jan 1, 2007

By Victor Nazimko

A new technique for reaming the holes has been tested. This technique is available for reaming a hole at its deep end creating an enlarged cavity that has helicoidal grooves oriented at less than 40 degrees to the hole axis. This technique increases bolt resistance by a factor 1.3-1.62; its bearing capacity by 3 times and enhances underground roadway stability. This technique is suitable for great depth (1000m and greater) and weak wet rocks.

Jan 1, 2008

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By N. I. Aziz

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack orientation.

Jan 1, 1992

By Christopher Mark

A new method for the design of longwall pillars, called "Analysis of Longwall Pillar Stability" (ALPS), is described. The method is the final result of a research program that included two major field studies, extensive reanalysis of data from other in situ measurements, and detailed evaluations of available pillar design methods. The key problem addressed by ALPS is estimation of the abutment loads applied to longwall pillars. Based on underground stress measurements made in mines in three states, equations for predicting the magnitude, distribution, and time-of-arrival of abutment loads are proposed. Stress measurements are also used to evaluate empirical pillar strength formulas for use in longwall pillar design. ALPS has been verified by application to case histories from several mining areas, and examples taken from the Pittsburgh and the Blue Creek seams are presented. Step-by-step guidelines for using this design method are also given.

Jan 1, 1987

By Paul N. Freeman

This paper describes the in-situ performance of two IFS powered support installations at Betws and Penallta Collieries in the South Wales Coalfield, United Kingdom. Intensive monitoring of all powered support functions, strata movement, support/strata interaction and coal seam disturbance permitted an extensive evaluation of powered support performance for all periods of the mining cycle. The influence of support design, support rating, face design, proximate strata and scam section upon support and operating performance are discussed. In-situ performance is compared to design specification and to the requirements of Production Instruction 1982/6. Aspects which show significant variation are highlighted. Particular attention is drawn to the precise analysis of support/strata interaction in the form of canopy and base loading profiles. This illustrates the influence of support rating and configuration in determining the interaction of the canopy and base with the proximate strata. Extensometric monitoring of the coalface highlights the potential zones of disturbance within the seam which allied with support position monitoring provides an accurate basis for theoretical considerations of support loading. Conclusions are drawn, the application of which may enhance the performance and operation of IFS supports in thin to medium sections.

Jan 1, 1992