Search Documents

By Don W. Murphy, Don M. Larsen

Advanced process control has been implemented at the Jerritt Canyon Mill. Plant production prior to 1997 was limited by grind circuit capacity. The installation of additional mill horsepower and an optimizing supervisory control system achieved a throughput increase in excess of 12 percent. The controller application utilized a seamlessly integrated fuzzy logic expert system for real-time mill control coupled with a neural network predictor for closed-loop feedback of particle size constraints. In late 1998, a second supervisory controller was installed to operate the fluidized bed roasters. The second controller optimized roasting conditions, increased plant throughput and improved metallurgical recovery.

Jan 1, 2000

By John A. Herbst, Kuang Y. Lee

Coarse particle size measurement is essential for the automatic control of a size reduction process like crushing or SAG milling in order to achieve optimal process performance. However, the on-line size measurement of coarse material is not easily obtained due to the problems of material handling and sample statistics. A technique based on advanced image analysis and quantitative stereology has been successfully developed and tested in a pilot scale setting. The chord length distribution of coarse particles on a moving conveyor was measured with an image analyzer and then transformed to the mesh size distribution with a stereological model and a special numerical method. Some test results as well as the technique's industrial suitability and limitations of this method are also discussed.

Jan 1, 1992

By Finn Ouchterlony

INTRODUCTION Much of present fracture toughness testing con¬cerns chevron notched specimens (Newman Jr., 1984) since these, in principle, require neither fatigue precracking nor more registration than failure load to determine fracture toughness. Two such specimens which can be made from diamond drilled rock cores with minimal machining are the Short Rod (Barker, 1977) and the Chevron Edge Notch Round Bar in Bend¬ing or CENRBB Specimen (Ouchterlony, 1980). Even if the precracking property is especially valuable for a material like rock, practice has made the relative advantages of these chevron notched specimens much less apparent (Ouchterlony, 1982; Ouchterlony and Sun, 1983). Enough remains, however, to have the Commission on Testing Methods of the International Society for Rock Mechanics (ISRM) focus on them as standard configurations in a "Suggested Method for Determining Fracture Tough¬ness of Rock Material", which is in preparation. This paper presents material which supports the ISRM effort: 1. An experimental compliance calibration of the Chevron Bend (CENRBB or CB for short) and re¬sulting formulas. 2. Specimen tolerances, evaluation formulas, and loading rate requirements relating to both Short Rod and Chevron Bend Specimens of suggest¬ed standard proportions. 3. Some fracture toughness values obtained with the Chevron Bend Specimen. This material is mainly based on two reports (Ouchterlony, 1984 and 1985). CALIBRATION OF THE CHEVRON BEND SPECIMEN Preliminaries The specimen and basic notation is shown in Figure 1 together with a straight notched variety (SECRBB). Subscripts c and s are sometimes used below to distinguish between them. Assuming linearly elastic conditions the load point compliance [ ]

Jan 1, 1986

By E. D. Attanasi

The US mining industry finished the traumatic 1980s with a strong economic performance. Worldwide economic growth and capital spending led to tight metal markets. So, 1989 metals prices were generally higher than average 1988 prices. Financial markets' volatility resulted from US junk bond defaults, heavy US savings and loan losses and effects on the US budget deficit, higher energy prices, and the seemingly intractable problems of some debtor countries. Moreover, the events in Eastern Europe promise fundamental changes in the world economic system for the 1990s. US mining companies that survived the decade had weathered economic changes that, at one point, reduced industry employment by 40%, drove oil companies to divest or liquidate recently acquired mineral subsidiaries, and led to substantial write-offs of reserves. Canadian and other international minerals firms experienced similar industry upheavels. The forced modernization and capacity rationalization produced an internationally competitive US industry. For example, even though 1989 US copper production was 27% greater than in 1980, industry employment was less than half the 1980 level. The steel industry and other minerals industries showed similar productivity improvements.

Jan 1, 1990

By William A. Faust

La Colorada Mine was begun in 1993 as a small heap leach mine and was the first operation for Eldorado Gold Corporation. 'This paper describes the growth of the mine to annual production levels near 60,000 ounces of gold and highlights recent improvements that were made to maintain a profitable operation by efficiency gains and cost containment programs.

Jan 1, 1998

By Richard C. Travis, Edward C. Dowling

A detailed kinetic study of the flotation installation at the Metcalf Concentrator revealed a rougher flotation circuit operating under less than optimal conditions. Based on these results, a project was initiated to approximately double the rougher flotation capacity by increasing the installed volume from 780 cubic meters to 1,560 cubic meters. This project, which was completed in early 1991, replaced the existing cells with larger capacity cells. A comprehensive analysis of results demonstrates significant metallurgical benefits. INTRODUCTION/BACKGROUND The Metcalf Concentrator is located in Morenci, Arizona and is part of Phelps Dodge Morenci, Incorporated. Sumitomo Metal Mining of Arizona is a minority partner in the operation with 15% interest. The Metcalf Concentrator is the newer and smaller concentrator and operates in conjunction with the Morenci Concentrator. Operating capacity at Metcalf is currently 48,000 TPD of ore on a 365 days per year basis. The Metcalf Concentrator was commissioned in 1974 at a 30,000 TPD operating rate for the purpose of treating ores originating in the Metcalf Mine. The mine takes its name from the former town of Metcalf which was named for Robert Metcalf who was credited with discovery of the mineral district. The predominant ore mineral is chalcocite which occurs as a secondary enrichment closely associated with iron pyrite. The host rock is largely granodiorite and quartz monzonite. The original rougher flotation circuit consisted of a total of six rows of Wemco 8.5 cu. meter (300 cu.ft.) flotation machines treating pulp from the two grinding sections (Sections A and B). Each row was configured in a 4-4-4 arrangement. Shortly after startup the throughput rate was increased significantly without sustaining a recovery loss. This increase was achieved by raising the target value for the particle size of the cyclone overflow which is the rougher flotation feed. Shortly thereafter, the capacity of the pump and cyclone began to restrict further increases in throughput. After testing, two 66 cm. (26-in.) cyclones and a 12-in. X 12-in. centrifugal pump replaced the original classification equipment. As a result of these modifications, the grinding section could routinely process in excess of 42,000 TPD. Due to the increased tonnage rates, limitations in the rougher flotation circuit performance were observed. In an effort to improve the performance of rougher flotation with this higher throughput, the speed of the flotation mechanisms was increased from 230 RPM to 250 RPM. This change improved the suspension of the coarser feed and induced additional air into the pulp. It did, however, apply additional strain to the motors, shortening their life. At these elevated processing rates, it was found that the dart valves operated almost entirely at the top end of the control range and could not efficiently handle upsets from the grinding section. This was remedied by lowering the end overflow weir and allowing some of the tailings to overflow the end weir. However, in order to obtain acceptable recovery levels, the flotation pulp was maintained at a high level, adversely influencing the rougher concentrate grade.

Jan 1, 1993

By M. H. Weinecke, B. P. Faulkner

This paper discusses the process for making lightweight aggregate, the waste materials that make good lightweight aggregate, the chemistry of making lightweight aggregate and the commercial prospects for making lightweight aggregate from wastes. Svedala Industries has been making lightweight aggregate (LWA) from waste materials for the last 10 years. Many claylike materials, such as coal fired boiler ash and washings from a granite quarry, can be used alone or with additional waste materials to produce commercially salable LWA.

Jan 1, 2003

By W. M. Schafer, C. F. Luckay, D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risks and the effectiveness of caps and covers. The information can also be used in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs) and lysimeters. Many of the monitoring devices can be linked to a data logger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1999

By Meliton M. Garcia, Satya Harpalani

The volume of gases produced in major and trace amounts as a result of detonation of explosives in an underground mine was determined. The volumes of major gases (CO, CO2, NO and N02) were measured immediately following detonation, during the mucking operation, and following the removal of muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The composition of the gases produced varied significantly depending on the composition of the explosive/blasting agent. An average of 95% of the gases produced were found in the test chamber immediately following the detonation, while 2% was found in the chamber following the removal of the muck. Several compounds were identified in trace amounts. Of particular interest was the detection of benzene, toluene, butenes, ethyl benzene and naphthalene since exposure to some of these compounds, even in trace amounts, could present a serious health hazard.

Jan 1, 1987

By S. Nickson, M. Grenon

Oriented borehole data provide the means to characterize a rock mass. In this paper, the geomechanical caving potential of a hard rock mine project is investigated. In particular, the influence of random joints to the resulting block size distributions is addressed. The implications of this approach in preliminary investigations on the choice of mining methods are discussed with reference to one site.

Jan 1, 2003

By G. T. Adel, W. Z. Choi

A model describing size reduction and mineral liberation during grinding has been extended to include multiple classes of composite particles. The majority of the model parameters have been directly determined using computerized image processing equipment to analyze the products from batch grinding tests. A coarse-grained sphalerite ore from Tennessee, representing a nearly ideal binary mixture of sphulerite and dolomite, has been used to experimentally validate the model for the case of dry batch grinding. In all cases, excellent agreement has been observed between the model predictions and the experimental results.

Jan 1, 1988

By Philip L. Hageman, Paul H. Briggs

An important tool for use in the geochemical assessment of abandoned mine-waste piles is a leach procedure that can easily be done in the field and used for on-site screening of historic mine-waste material. We have developed a simple field leach test that is an effective indicator of waste pile geochemistry and can be used in order to establish the relative geochemical fingerprint for a given pile. This simple procedure also provides indication of the potential chemical composition of run-off from the weathered surface of these piles. As part of developing the technique, a comparative study was carried out on eight mine-waste composite samples from different deposit types. Splits of all eight composites were leached using the field leach test procedure and a modified version of EPA Method 1312 (SPLP). We found that the field leach test consistently provides relative indication of leachate geochemical trends comparable to leachate data derived from the more regulated, time consuming and laborious EPA Method 13 12 (SPLP).

Jan 1, 2000

By K. Y. Haramy, B. T. Brady

A scale-invariant theory of the strength and deformability, of rock masses in static equilibrium and at incipient failure is proposed The theory provides a rationale, for designing structures in rock. This paper presents results of experiments conducted by the US Bureau of Mines and presents theoretical methods to determine and interpret the in situ strength of rock masses using the borehole shear tester.

Jan 1, 1996

A brief description of the mining method and ventilation system of the San Manuel Mine?s first presented; this is necessary to an understanding of the heat problem and cooling system. The problem of heat at San Manuel is discussed. Charts and graphs showing the relationships between ambient surface air and underground temperature conditions are given. A history of attempts to cool air at San Manuel is presented, starting with the first refrigeration type air coolers which were used in development headings, and followed by the underground water chillers that were used in conjunction with cooling coils. Goals for design of a centralized cooling system with ultimate heat rejection through surface cooling towers are presented. The problems found with using the centralized system in main cooling coils are discussed. Plans for modification of the centralized system as utilized is the summer of 1987 are given, along with results obtained and problems with the system. Plans for subsequent modifications are presented.

Jan 1, 1988

By Andrzej M. Wala

A prototype expert system for planning and designing an underground coal mine has been developed in a doctoral study at the University of Kentucky. This prototype expert system for underground coal mine planning and designing consists of a number of knowledge bases concerning different elements of design (e.g., ground control, excavation and bulk materials handling, ventilation, etc.). The objective of this paper is to present the development process of the ventilation design knowledge base for this prototype. This expert system prototype is intended for building an instructional expert system for underground coal mine design. Therefore, the undergraduate course on mine design has been used as the basis, for its development. Because of the availability of knowledge and expertise, this research study has been limited to development of a knowledge model for the Appalachian coal mining region.

Jan 1, 1993

By S. Peng, Yi Luo

Subsurface strata movements and deformations associated with underground longwall mining activities could cause certain influences to subsurface structures and water bodies. Methods have been developed for the prediction of final and dynamic subsurface movements and deformations induced by underground longwall mining operations in the eastern coal fields. Two new types of strata deformation, vertical and total strains, which could be useful in the field of subsidence research in assessing subsidence influences to the subsurface structures and water bodies, have been introduced. Using the subsurface subsidence prediction model, three types of subsidence influences to surface and subsurface hydrological systems have been identified. Attempts have been made to quantify the two types of subsidence influences that could cause water loss and could lower water levels in aquifers.

Jan 1, 2010

By E. R. Braer, C. J. Bise

The trend in underground room-and-pillar coal mining is to employ remote-controlled, continuous-mining machines and extended cuts to depths of 12 m (40 ft) or more. This system of coal extraction, adopted by more than 435 mines, can create additional worker safety hazards. To address the ground-control-related safety hazards, a combination of statistical analysis and numerical modeling was used. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the coal mine roof rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling was completed to predict roof displacements during extended-cut mining. This paper describes the results of these studies and their impacts on the safety of extended-cut mining.

Jan 1, 2000

By R. P. Plasket, G. M. Dunn

The cobalt plant was successfully commissioned in mid-1983. It is located within the company's nickel - copper re finery situated in Springs, South Africa. Plant design, which began in 1981, made provision for the corrosive process environment, stringent environmental standards, and the latest noise abatement requirements. In addition, the process flowsheet for the primary recovery of the cobalt byproduct and the purging of six impurity metals (nickel, iron, copper, manganese, lead, and arsenic) was designed with simplicity as a primary objective. High purity cobalt powder has been produced since commissioning.

Jan 1, 1987

The application of Kirchoff's laws to two adjoining mine ventilation network meshes containing fans results in the construction of two general quadratic equations. These equations may be solved to give the resultant airflows and hence fan duties within the system for given network parameters and fan characteristics. This technique has a wide application for calculating the duties of fans in various combinations within a mine ventilation system. Recent difficulties in economically maintaining environ- mentally safe conditions in underground working areas distant from main ventilation fans has led to increasing interest in the use of controlled partial recirculation of ventilation. This paper develops a recirculation model which can be solved directly using mathematical techniques obviating the need for iterative techniques such as the Hardy-Cross method. The advantage of a direct mathematical analysis is that mathematical algorithms may be constructed to completely describe the ventilation system under a wide range of operating conditions. This technique is applied to controlled partial recirculation ventilation systems to demonstrate its advantages for mine ventilation planning.

Jan 1, 1989

By K. S. Eric Forssberg, Lennart Ryk

The paper discusses coal utilisation in Sweden. All hard coals have to be imported from other countries. Peat from domestic sources is used as a complement. Environmental legislation and taxation on fuel and emissions are severe. This situation affects the procurement, preparation, handling and use of coal. The paper presents: • R&D projects concerning deep cleaning of thermal coal. • Handling and treatment of coal used in PFBC boilers and for blast furnace injection • Dust prevention for coal and peat briquettes. Procurement of coal emphasising quality and environmental issues.

Jan 1, 1995