Search Documents

By Michel L. Bilodeau

Mineral exploration is a sequential information gathering process. Primary exploration programs filter favorable areas through a series of geological, geochemical, and geophysical tests resulting in the discovery of mineral occurrences. The most favorable of these discoveries provides economic justification for a delineation drilling program. The purpose of delineation drilling is to provide information for estimating relevant physical characteristics of the mineral occurrence. These estimates are used to evaluate the exploration project and, eventually, the economics of mine development. Delineation drilling normally completes the exploration process. If the assessed economic characteristics of the delineated occurrence provide justification for mine development and production, an economic mineral deposit is the end result of the exploration process. Subsequently, a development drilling program is initiated to obtain the necessary data for detailed mine planning. The delineation drilling stage is in itself a sequential investment process. As delineation information accumulates, the reliability of geological estimates is improved and, thus, the uncertainty associated with the assessment of profitability criteria is reduced. Delineation drilling should continue as long as the marginal benefits, which result from improving the reliability of profitability criteria, exceed the marginal costs associated with the additional drilling.

Jan 1, 1979

By F. Kennedy

Consolidation Coal Co. (Consol) supports an active research and development effort to improve the safe, productive mining of coal and to use coal in an environmentally acceptable manner: Attention will be focused on degasification of coal seams, continuous coal transport systems, earth sciences activities, and coal combustion. Brief mention will be made regarding the SO2 emissions control programs. The research program constitutes about 1 % of Consol coal sales, which positions Consol as the preeminent coal company supporting broad-based research addressing the full spectrum of the various problems associated with using the nation's abundant reserves of economical, readily available fuel.

Jan 1, 1990

By V. R. Degner

Given: the process tonnage, performance objectives, and plant floor area, the paper will outline the metallurgical and machine hydrodynamic scale-up procedures for translating the lab flotation test results to the design of a full size flotation machine installation, including the machine number, size, and arrangement. Machine selection considerations for rougher, scavenger and cleaner duty, and special considerations relative to specific applications, will be summarized where appropriate. The value of kinetic modeling in quantitative metallurgical (lab to full size machine) scale-up will be reviewed considering a coal installation, and design information for additional applications such as copper, molybdenum, iron, phosphate, and potash will be discussed.

Jan 1, 1986

By Lei Zhang, P. Somasundara

The beneficiation of phosphate is complicated due to its sparingly soluble nature. The surface proper- ties of phosphate and associated minerals are determined, in addition to the ionic composition of the solution, by the dissolution of the lattice ions of the minerals and subsequent complexation, hydrolysis, adsorption, and precipitation of the dissolved species. These, in turn, are influenced by the pretreatment of the mineral. These complex interactions determine the interfacial properties of phosphate and associated minerals and thereby the efficiency of beneficiation processes such as flotation and flocculation. Under- standing of the chemistry involved in such systems is helpful to develop the optimum beneficiation schemes. It is shown that desired selectivity can be achieved by controlling the chemistry of the systems. More important, the need to conduct development tests under plant conditions is clearly demonstrated.

Jan 1, 1999

By D. J. Hutchinson, S. Nickson

Cable bolts are used as a means of rock support around underground excavations in many mines across Canada and around the world. A substantial body of research on cable bolting was conducted at a number of Canadian universities and mines from the mid-1980s through the 1990s. Since then, research into selected areas of cable bolting practice has continued in Canada. The research has focussed on cable bolt instrumentation and on the inclusion of cable bolts in empirical stope design techniques. A review of cable bolting practice is now warranted at many mines. It has been five years since the completion of the previous substantial body of Canadian academic research and the associated advancement in understanding of cable bolt design, implementation and verification practice. Attempts were made at that time to transfer the new design procedures and performance assessment technologies to mine-site personnel. In some cases, this was effective, and ground control personnel continue to improve on their cable bolting practice at each specific mine site. However, at other sites, experienced people have moved on, and the new, less experienced personnel do not have access to the training or technical resources required to improve their understanding of the subject. In other cases, the technology was not transferred effectively to practitioners, with the result that substantial improvements can be made to the cable bolting practice at those mines. Guidelines for auditing cable bolting practice are provided in this paper. The guidelines include a discussion of the objectives of the audit, suggestions for audit procedure and a summary of the possible outcomes of a cable bolt audit. The objectives of an audit might include assessing the reasons for unexpected cable bolt failures, evaluating the quality of the installation procedures, quantifying the efficiency of the cable bolt system and assessing training requirements and procedures. A cable bolt audit should include consideration of all aspects of the cable bolting cycle, including the design, implementation and verification phases of the operation. At the end of the audit, a ranking should be assigned to the components of the cycle. The ranking system can then be used to identify items that require immediate attention, others that could be improved and others that are adequate. Following completion of a cable bolt audit, increased confidence in the support system and its application is generally, found, along with the potential for cost savings in many cases.

Jan 1, 2002

By Paul J. A. Lever

The mine environment is dynamic and operating conditions change continually and are difficult to predict. New equipment, variable geological conditions, modified layouts, and different equipment operators make monitoring and control system difficult to apply without continual software maintenance. The paper reports on algorithms that were developed, encoded with Knowledge Craft Tools, and tested on underground coal mine data to adapt to the dynamic environment. The system receives data from sensors in near real time and then identifies patterns in the data. Using a set of mode features the data is automatically checked to determine the present operating mode. When the operating mode changes from the previous shifts, the system automatically learns the new mode characteristics and uses that mode context for further data analysis. The concepts presented in this paper are applicable to a wide variety of mining scenarios, not just underground coal mining.

Jan 1, 1992

By F. F. Aplan, V. Choudhry

This investigation is an exploratory study to evaluate a large number of potential pyrite depressants for use during coal flotation. Subsequently, the more promising reagents can be evaluated in detail. Several reagent categories (such as alkalis, lime, oxidizing agents, reducing agents, specific inorganic ions and dispersants) that were found to be effective pyrite depressants are discussed here. Other pyrite depressants will be discussed in Parts II and III.

Jan 1, 1993

By S. O. Yuan, R. L. Grayson

As a followup to a USBM-sponsored research project, the authors utilized the knowledge-base structure and system concepts from a Sun Sparcstation-based worker-scheduling system of the mine-management support system to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, including their availability and work priorities during a shift. The system can optimally allocate manpower on a work shift and can delineate supervisory training responsibilities. The various components of the software, including enhancements made to the original system, are described in detail.

Jan 1, 1998

By K. N. Han

The leaching behavior of palladium in ammoniacal solutions was investigated by using the rotating-disk technique in an autoclave. The study included the effects of rotation speed, temperature, oxygen pressure, composition of ammoniacal solutions and catalysts on the overall leaching rate. The dissolution of palladium in ammoniacal solutions was discussed in terms of the thermodynamics and a kinetic model. Even though the Eh-pH diagram suggests that palladium metal can dissolve in ammoniacal solutions at room temperature, it was found that the dissolution was very slow at temperatures below 100 °C but was significantly improved at higher temperatures. It was also found that the rotating speed of the palladium disk had no effect on the leaching rate. The apparent activation energy was found to he 69.7 kJ/mole. Based on the results obtained, it was concluded that the dissolution of palladium is controlled by chemical reaction.

Jan 1, 1999

By S. M. S. Azghdi, K. Barani

The effect of microwave treatment on the surface roughness and wettability of chalcopyrite (CuFeS2 ) and on the chemical composition of its surface was studied. The microwave source was a conventional multimodal oven with frequency of 2.45 GHz and maximum power of 900 W. Pure chalcopyrite specimens and purified chalcopyrite concentrate were used in this study. Analysis using atomic force microscopy showed a decrease in the surface roughness of the chalcopyrite after microwave radiation. This decrease may be due to oxidation of the surface and formation of iron oxide. Moreover, the surface wettability of the chalcopyrite mineral increased with increasing duration of microwave radiation, which was in good agreement with the micro-flotation mass recovery results. The increased wettability of the surface may be attributed to the decreased surface roughness by microwave radiation. Analysis using scanning electron microscope/energy-dispersive X-ray spectroscopy indicate that after microwave radiation, the contents of sulfur and iron increased whereas that of copper decreased on the surface of the chalcopyrite, significantly changing the average atomic number of the chalcopyrite surface.

By G. Meiers, M. O’Kane

Dry cover systems as a closure option for management and decommissioning of waste rock and tailings is a common prevention and control technique used at numerous sites around the world. Numerous site-specific factors control the long-term performance of dry cover systems. Site-specific climate conditions are one of the key factors to consider when determining the objectives of a dry cover system because these conditions will significantly influence long-term performance. There are advantages and disadvantages of characterizing the site on an annual basis as generally a “dry” site (annual potential evaporation greatly exceeds annual precipitation), or generally a “wet” site (annual precipitation meets or exceeds annual potential evaporation). The field performance monitoring data and discussion presented herein illustrates the caution that is required when using these “annual” criteria for characterizing site climate conditions. Numerous sites exist where precipitation exceeds potential evaporation on an annual basis; however, the site typically experiences hot, dry summer months where evaporation greatly exceeds rainfall. These dry summer conditions have a strong influence on long-term performance. In contrast, sites where potential evaporation exceeds precipitation on annual basis, typically experience periods of the year when a moisture surplus occurs, which also impacts on long-term performance. This paper uses soil-atmosphere cover design modelling and field performance monitoring from sites in Canada, Australia, and the United States to demonstrate the importance of considering site-specific climate conditions when predicting long-term cover system performance.

Jan 1, 2003

By Yuting Xue, Khaled Mohamed

The failure of coal ribs is a major hazard in underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have been working on the development of an engineering-based rib control method. A user-friendly standalone application, called Design of Rib Support (DORS), is being developed to ease the calculations of rib support. DORS can estimate the Primary Rib Support Density (PRSD, ton/ft2) for development loading. However, it still needs to take account of another key factor, bolt length, in rib support design. The bolt length can be estimated from the rib fracture depth, and this study focuses on the coal rib fracture depth analysis with numerical modeling and artificial neural network. A total of 331 FLAC3D simulations with different mining scenarios and rib conditions were conducted for this study. Machine learning was then used to predict coal rib fracture depth under different conditions. Based on the numerical simulations, the parameters for mining scenarios and rib conditions were collected as features for machine learning, and coal rib fracture depths were collected as the target to predict. Good data correlation (r-square) was obtained with the use of an artificial neural network. The

By Gregory M. Rumbaugh, Christopher Mark

"The proliferation of unconventional gas well development in the Northern Appalachian coalfields has raised a number of mine safety concerns. Unconventional wells, which extract gas from deep shale formations, are characterized by gas volumes and pressures that are significantly higher than those observed at many conventional wells. The gas is composed largely of methane as well as other hydrocarbons. Hundreds of planned and actively producing wells penetrate protective coal pillars or barriers within active mine boundaries, including chain pillars located between longwall panels. Gas released from a well damaged by mining-induced ground movements could pose a risk to miners by flowing into the mine atmosphere. The mining-induced ground movements that may cause well damage include conventional subsidence, non-conventional subsidence (e.g., bedding plane slip), pillar failure, and floor instability. This paper describes the known risk factors for each of the four failure mechanisms. It includes a framework that can guide the risk assessment process when mining takes place near gas or oil wells.INTRODUCTIONSouthwestern Pennsylvania has served for centuries as a producer of coal, oil, and natural gas. Coal mines were first developed in the Pittsburgh Coal Seam in the 1760s, with the first recorded mine in 1761 being the Fort Pitt Mine (Edmunds, 2002). Natural gas was introduced to the region when the Haymaker Well in Murrysville, Pennsylvania experienced a blowout on November 3, 1878. Although it was originally drilled prospecting for oil, it produced an estimated 30 million cubic feet per day of natural gas. Without well controls or pipeline infrastructure in place, it burst into flames and lit the night sky for over a year. Soon after, the Penn Fuel Company continued development of the Murrysville gas field and is credited with making Pittsburgh, Pennsylvania the first major city in the U.S. to have natural gas supplied for home and industrial uses. “Natural gas is king in Pittsburgh,” proclaimed an October 18, 1885, article in the New York Times headlined “Value of Natural Gas, Its Use Clarifies the Atmosphere at Pittsburgh” (AOGHS, 2018). By the early 1900s, coal, oil, and natural gas production had reached the southern extents of Pennsylvania in Greene County. The county had first produced oil in 1886, and shortly after began producing natural gas in 1890. By 1906, over 1,300 wells had been drilled (Stone and Clapp, 1906)."

Jan 1, 2019

By Todd Kilduff, Paul Wilkinson

Microtunneling is rarely a straight forward “business as usual” endeavor. More often than not, these projects take twists and turns that require on the fly, out of the box solutions to get the project completed. This paper is a case history of a 63-inch diameter, Permalok, microtunneling project, extending nearly 700 linear feet under a hill forming the left-hand abutment to an earth embankment tailings dam. The job had three major and unexpected challenges that required unorthodox solutions. Challenge #1— Face Configuration: The Santiago Formation, a cemented sand formation with widely varying strengths, presented a challenge to configuring the face with regards to the number and length of pics and cutters. Subtle differences in type and size of the tooling had a big impact on the performance of the machine. Challenge #2—Eccentric Loading: Issues at the launch shaft with the Permalok pipe adaptors caused eccentric loading on the casing pipe. This issue resulted in overstressing and breaking of several pipe joints that ultimately led to seizure of the tunnel. Challenge #3—Back-tunnel Excavation and MTBM Recovery: There were many detailed considerations into excavating a recovery tunnel to retrieve the MTBM, especially being under a high hazard earth embankment dam.

Jun 13, 2021

By John R. Thalimer

For the past four years the U.S. Bureau of Mines has investigated the early detection of insulation failure in squirrel cage induction motors. Data modeling techniques based on values calculated from a motor's voltage and current phasors were used to produce a pair of polynomial equations that calculate a motor's insulation leakage current and power. This paper describes a prototype system using these models that monitors six motors on a continuous miner for insulation leakage in order to anticipate insulation failure. The system consists of a motor-data system for each motor on the machine, a control computer located some ' distance from the miner, and a serial bus to interconnect these items. Each motor-data system consists of an analog interface to the motor's voltages and currents, a single-board computer that reads digitized data and calculates voltage and current phasors, and a bus node that interfaces the single-board computer with the serial bus. The control computer can request and receive phasor data from any motor-data system on the bus. Using models developed at the Bureau, the control computer calculates and displays two deterioration values for each motor, one for leakage current and the other for leakage power. These values are then stored into a database from which the user can display them over time.

Jan 1, 1992

By J. Smolensky, M. Paul

The Nordhalde is a waste rock pile resulting from uranium mining near Ronneburg, Germany. The pile contains over 27 million m3 of waste rock. Typical seepage water has a pH of 2.7 and a sulfate concentration of 10,000 mg/L. Geochemical investigations of the Nordhalde from 1993 to 1996 included drillholes, test pits, ABA and metals analyses, column tests, and a detailed review of the construction history of the pile. In 1996, eight drillholes were instrumented for monitoring oxygen and temperature. Monitoring continued for a fill year. Hourly temperature and pressure readings were taken by automated data recorder. Oxygen concentrations were measured three times per week, and periodic gas samples were obtained for complete analysis. The resulting data set is believed to be one of the most comprehensive of its kind. Effects noted elsewhere, such as thermal convection, are evident. However, unlike other data in the literature, the NordhaIde data shows a strong seasonal effect, with convection dominating oxygen transport only in the winter months. Analysis of the data allowed the amount of contaminants associated with ongoing and historical oxidation to be compared, and results were used to assess the potential effectiveness of proposed remediation measures.

Jan 1, 2000

By William J. Lang

In just over a generation, the United States bentonite industry has grown from almost a rake and shovel operation into one with a multimillion ton annual production rate and exports to all corners of the globe. Bentonite production, pressed to keep pace with the soaring demand, has increased more than 10 fold in the last 30 years. The worldwide demand for bentonite is expected to double during the next eight to ten years. It remains to be seen whether U.S. producers will be able to maintain the dominant position in the world market. It should be noted that accurate statistical information regarding production or market information is difficult or impossible to obtain abroad and also within the United States. Published information obtained in response to questionnaires of the Bureau of Mines tends to be on the conservative side. FOUNDRY It has only been in the last thirty or forty years that bentonite has become an indispensible part of the age old metal casting industry. The relationship has proven most beneficial to both industries and promises to be long lasting. The foundry market for bentonite was the least of the three major markets twenty years ago but now leads all others and consumes 1/3 or more of the

Jan 1, 1971

By Fernando de Oliveira Durão

A complete computer package for the steady-state simulation, either in analysis or in design mode, of mineral processing flowsheets is described. The main features of the simulation package are: modular architecture, flexible structure and sequential solution strategy. Different detail levels of mathematical models of several mineral processing unit operations have been developed and implemented as unit modules (FORTRAN routines). Unit operations currently modelled are: coarse/fine crushing, grinding, screening, hydrocyclone classification, gravity separation, heavy media separation, froth flotation, high gradient magnetic separation and solid-liquid separation. In design mode, a simulation study is stated as a general non linear optimization problem. The objective function is a weighted sum of square deviations between the design specification set points and the calculated values, subject to non linear equality and inequality constraints. The optimization problem solution is obtained solving successive Quadratic Programming subproblems followed by inexact line search of an exact penalty function (Powell algorithm). One non trivial example is discussed, illustrating the design capabilities of the simulation package.

Jan 1, 1992

By George J. Thompson

Almost all persons connected with mining industry have had an exasperating experience like the following: 'On a cold and frosty morning in mid-January, you find yourself quite happy with the world. Production is up and the mine has been running smoothly. All at once the radio cracks up your tranquility -- 'so and so' piece of equip¬ment has broken its 'whatzit'. Now the iron is in the fire, and things have to be fixed quick.!' This can be a major failure which will bring the whole operation to a grinding halt or just one of the numerous maintenance headaches on an auxiliary piece of equipment. After one has experienced a major or minor catastrophe, he has to wonder whether some other methods with respect to design and maintenance would help prevent these unexpected calamities. The objective of this paper is to gain an insight into the charac¬teristics of steel at cold temperatures so that better decisions can be made with respect to maintenance and repair of mining equipment. Most machinery and their structures are exposed to cold temperatures. Even in locations as far south as Alabama and Arizona, brief periods of cold in winter months can adversely affect the ability of mach¬ines to do their work. To understand the background of cold temperature brittle fracture, jet us examine its basic elements. First, when steel gets cold, it gets brittle. This is best described by Figure 1. This graph shows a typical stress/strain curve of a mild or medium grade steel at room temperature. Stress is defined simply as the amount of force acting on one square inch of

Jan 1, 1972

By Robert A. Jankowski, Fred N. Kissell

Recent allegations about tampering of coal mine dust samples have led to suggestions that the coal industry needs a respirable dust compliance sampling method that is less subject to tampering. The sampler designs under consideration include fixed location monitors that could be mounted on a mining machine or located at a stationary location in the mine, and samplers that are worn, like the existing samplers. Fixed-point samplers have a design advantage, since samplers worn on the body will have size and weight limitations. On the other hand, in some cases there are respirable dust concentration gradients, which will dictate careful placement of a fixed-point sampler inlet to determine the exposure of workers. This study examined dust concentration-gradient data obtained by the Bureau of Mines and others over the last decade. As an example of spatial gradients at continuous miners, a fixed-point monitor located in front of the operators cab shows a higher dust concentration than a sampler located on the operator and reduced exposure when the sampling location is behind the operator cab. It may be necessary to use a sampling tube with a machine mounted monitor, to sample in the operators breathing zone in the cab to provide a more representative sample of the miners exposure. For face workers on longwalls or on continuous miner sections using remote control, the study shows significant dust level gradients and gradient variations between typical operator positions and mining machine locations. In addition, if fixed-point monitoring is used to monitor an area, vs the exposure of specific workers, dust control technologies currently employed to ensure reduced dust exposure such as the diversion of dust laden air away from the workers, or through the use of remote control of mining machinery may not indicate the same dust reduction obtained with current sampling techniques.

Jan 1, 1993