Search Documents

By C. K. Lee

The influence of passageway fires on ventilation flows was investigated in three horizontal fire tunnel s: 1. a laboratory-scale fire tunnel network, 2. a small-scale fire-plume tunnel, and 3. a large- scale simulated mine gallery. Wood was used in the first and third tunnel and gas-burners were used in the second one to generate passageway fires. Experimental measurements included gas mass flow rate, velocity, temperature and pressure in the passageways and exhaust fans. The overall and local effects of the fires were investigated by comparing these measurements obtained before and during the fires. Results show that a passageway fire essentially increases the flow resistances of the passageways of a tunnel flow network by virtue of volatile fuel mass injection and high combustion temperatures. The ventilation air flow rate is consequently throttled to lower values than that before the fire. At severe throttling, reverse flow occurs. Conditions for reverse flow are characterized by two Froude numbers based on gas velocity and density upstream of the fire, and height of the passageway. The Froude numbers and the characteristics of the passageway fire are necessary to analyze mine ventilation/fire interaction and to predict mine ventilation patterns during fires.

Jan 1, 1980

By Peikun Liu, Guangyu Sun, Raja V. Ramani, Shambhu Sharan, Raman Srikanth, Bharath K. Belle

The contribution of the various outby sources to the contamination of the panel intake air has been the subject of a relatively small number of studies. In this paper, after a brief review of past studies, results from recent experiments on rates of contamination of intake air by outby dust sources are presented. Present study indicates that each outby source by itself may not be a major contributor. The loading point in the continuous miner section did not appear to be of major concern from contamination point of view. Belt entry including transfer point contributes significantly to the intake air dust level, though reentrainment was not a major source of dust. In longwall panels, the stageloader-crusher was the most dominant source. The panel-to-main belt transfer point was not a major source. Taken collectively, the contribution of all outby sources can be significant. In one longwall section, at the beginning of the longwall face, the contribution of all the outby sources and the headgate cut-out operation was observed to be about 80% of the permissible exposure limit (2 mg/m3). In modem high production longwalls, the application of effective dust control measures to reduce the dust generated from the outby sources is essential to achieve compliance with the dust standards.

Jan 1, 1997

By A. J. Basu

Rock mass properties testing for determining strength parameters is an integral part of geomechanics. These tests are performed either in a laboratory environment or in a field (in-situ). The authors share their experience in using numerical modelling in simulating the laboratory test procedures. This approach helps studying the rock breakage and failure mechanism more efficiently and provides a high degree of visualization. Moreover, imperfections and discontinuities can be easily incorporated in these models. This capability of providing arbitrary fractures and discontinuities facilitates in building a large knowledgebase of rock strength and failure mechanisms. This knowledgebase may then be used to generate heuristics for determining rock strengths for rock mass with fractures and discontinuities.

Jan 1, 1997

By Christoph Schulte-Schrepping, Bou-Young Youn, Rolf Breitenbücher

"The main requirements of two-component grouts are a high workability and sufficient stability against sedimentation with a retention time of more than 72 hours, as well as a rapid strength development im-mediately after grouting. Component A usually consists of OPC, water, bentonite, and retarding agent. Component B, a liquid accelerator, is added to Component A during grouting at the end of the shield tail. Current investigations on different compositions of Component A showed a high workability lasting for at least 72 hours. The workability could be extended with increasing amount of the retarding agent to a certain degree. An increase of the bentonite content improved the stability of the mix, but had a negative impact on the flowability respectively the workability of Component A. High compressive strengths could be rather achieved by an adapted mixing ratio of Component A and B than by increasing the amount of the accelerator. Thereby, the interactions and compatibility of the selected constituents play an essential role. INTRODUCTION In mechanized tunneling with segment linings, the annular gap between segment ring and soil must be filled instantaneously with an adequate grouting mortar. The main functions of the annular gap grouting are to stabilize the tunnel lining and to minimize settlements of the ground surface at the same time. Thereby, two contradictory requirements are demanded on annular gap grouts: On the one hand a high workability and sufficient stability against sedimentation, on the other hand a rapid strength develop-ment immediately after grouting. Besides single-component grouts, which achieve the necessary stiffen-ing by dewatering into the surrounding soil, two-component grouts are used, especially in cohesive soils with a very low permeability. Basically, annular gap grouts are almost exclusively defined on empirical basis. Fundamental studies about the constituents and composition of the grout as well as the related achievable properties are still missing so far. Therefore, it is necessary to investigate the material-specific correlations regarding the relevant parameters of annular gap grouts – workability and flowability, stability of the mix as well as strength development – in comprehensive experiments. Based on the knowledge gained from the investigations, it should also be possible, to perform the grouting material according to a real design concept and thus, to ensure an adequate grouting in prac-tice considering the geological and hydro-geological conditions."

Jan 1, 2016

By Jon T. Langstaff

The microseismic method of detecting instability and high-stress zones in underground mines was first developed in this country by the US Bureau of Mines in the early 1940's (Obert and Duvall, 1957). Early laboratory experiments showed that when competent rocks are stressed in a testing machine, the rock noise rate (number of rock noises per unit time) increases with increasing applied stress. This increase is more pronounced as the ultimate strength of the rock is approached. Subsequent testing of rock noises in underground mines confirmed this laboratory experience and much effort has been directed in recent years to make use of this property to develop a practical method of predicting rock failure. Investigations conducted in the Coeur d'Alene district mines have pointed out a definite relationship between the stress buildup in a rock mass caused by mining activity and the emission of audible and subaudible seismic activity (microseisms). In 1968, a concentrated joint effort by USBM Denver Mining Research Center and American Smelting and Refining Co. at Asarco's Galena mine was undertaken to verify several theories regarding the generation of microseisms (Blake, 1971; Blake, Leighton, and Duvall, 1974; and Kovacs, 1973). Findings indicate that (1) rocks under stress emit detectable seismic energy; (2) the energy source can be located using a triangulation method involving travel time differences to various receiving stations; (3) the rate of release of seismic energy increases with increasing stress; and (4) this increase in noise generally precedes a major rock failure (rock burst).

Jan 1, 1979

By K. Fotoohi

This paper presents a basic, and yet practical, three-dimensional finite element model that was developed by the authors for stress/stability analysis of mine structures. While the code is linear elastic at this stage, it has some practical features that make it an attractive tool for mine design. Such features include: simulation of mine backfill support, mining induced strain energy calculation, powerful out-of-core frontal solver and failure analysis by Mohr-Coulomb or Hoek-Brown failure criteria. Model development criteria are discussed, and the potential application of the model to mining is demonstrated by design examples.

Jan 1, 1998

By B. H. Kim, P. Zhang, M. A. Van Dyke, D. Su, H. Dougherty

The National Institute for Occupational Safety and Health (NIOSH) has been evaluating longwall mining-induced strata fractures and their impacts on casing stability of Marcellus shale gas wells located in longwall pillars. To understand the extent of overburden fractures after longwall mining, NIOSH researchers drilled a postmining corehole into the fractured strata above the Pittsburgh coal seam longwall gob. Knowing the extent of the fracture zone height will help gas operators minimize the hazards of drilling into longwall gobs. The core was retrieved from the surface down to the top of the gob void. Various fractures were encountered varying from 35 to 64 degrees, depending on lithologic type and relative closeness to the gob. The longwall panel dimension was 457 m wide and 3657 m long, in which the total fracture zone height was found to be at 141 m and the hydraulic connected fracture zone at 87.7 m above the top of the Pittsburgh seam. In addition to core drilling through the gob, FLAC3D modeling was also used to simulate the formation of fracture zone and the orientations of longwall-induced fractures. This study provides much-needed evidence on the fracture zone of Pittsburgh seam longwall gobs to help gas operators avoid potential hazards associated with drilling through highly fractured zones

Mar 2, 2022

By Timms. Greg P., John W. Bennett

A field-based method for measuring the diffusive oxygen flux through covers placed on sulfidic waste rock dumps has been developed and applied at a number of mine sites. The technique provides a means of quantifying oxidation rates in dumps and can thus be used to assess the effectiveness of cover systems. Two instruments can be used. The first is portable and easy to set up, enabling a picture to be built up of the overall diffusive flux into a dump by making measurements at a sufficient number of locations. The second is installed beneath a cover and is preferred in situations where oxygen is consumed in the cover since it provides a direct measurement of the oxygen flux into the underlying waste rock.

Jan 1, 2000

By Ingo Kaundinya

"INTRODUCTION Tunnels are important elements of the German federal road network which have to cope with an increasing traffic load especially of heavy goods vehicles. In order to ensure a high availability and safety level for these key infrastructures, big efforts are required by owners and operators in order to keep all infrastructures up to date. This mainly relates to current European regulations regarding tunnel safety (Directive 2004/54/EG) [1] and their national implementation, which must be fulfilled by many existing tunnels. In this context the German Federal Government spends more than 1.1 billion € for the structural and operational retrofitting of more than 120 existing road tunnels. As many of these projects have recently been finished or are still under progress, experiences and best practices could be reported. After the description of current requirements in national standards regarding structural fire protection, the paper gives an example for an upgrade of a tunnel’s fire protection by installing an additional fire protection system, which is a quite costly measure. Another possibility to fulfill current requirements regarding structural fire protection could be the numerical proof of sufficient bearing capacity of a structure. The influence of different fire loads and fire durations on the bearing capacity of typical road tunnel structures have been investigated in a research project funded by the German Federal Ministry of Transport (BMVI) and coordinated by the Federal Highway Research Institute (BASt). The results of this research project have been used to define a procedure how to investigate existing tunnels regarding structural fire protection. Finally, the research results have also been the basis for a current update of national standards for tunnel construction. REQUIREMENTS REGARDING STRUCTURAL FIRE PROTECTION The structural fire protection design of road tunnels is usually based on temperature-time curves of exposure to fire, for simplicity called ""fire curves"". The fire development after fire growth is illustrated with fire curves. Fire curves can be subdivided into a heating-up phase, a fully developed fire phase, and if applicable, into a cooling-off phase (cf. Figure 1). During the fully developed fire, the fire remains at a certain temperature level."

Jan 1, 2016

By Blair K. Salisbury

Dissolution within Permian evaporites of the Delaware basin has created extreme lateral geologic and physical property inhomogeneity within and above the evaporites. Discriminating a sulfur deposit's geophysical signature from other variances is difficult. This is particularly true of porosity-dependent gravity and electrical methods. However, other techniques that detect alteration of strata above sulfur deposits may be applicable individually or in combination with other types of data. Relationships between sulfur deposits and gravity, magnetic, gamma radiation, spontaneous potential, and soil geochemical measurements are illustrated by data from several Delaware basin geophysical and geochemical surveys.

Jan 1, 1992

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study was to investigate the influence of amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and organic acids (citric, malic, tartaric, fumaric, oxalic, succinic and ascorbic acid) on gold extraction from silicate ore. Use of amino acids to extract gold was preferred compared with organic acids due to the presence of carboxylic group and amine groups in amino acids. Among the assessed amino acids, aspartic acid and glutamic acid had higher capacities to extract gold due to their structures, which lacked aromatic rings and long side chains. Organic acids could also extract gold. In particular, oxalic and succinic acids had the greatest capacity to extract gold versus the other tested organic acids. Moreover, aspartic acid had a greater capacity to extract gold from ores than the same concentration of succinic acid. We confirmed the aspartic acid and succinic acid functional groups by Fourier transform infrared spectroscopy. The findings revealed that aspartic acid had a greater capacity to extract gold than succinic acid due to the presence of both amine and carboxylic groups (succinic acid contained only a carboxylic group). The optimal gold:aspartic acid molar ratio was 1:6 and low concentrations of aspartic acid extracted 35–42%of gold from silicate ore within 15 days. This can be used as an alternative to traditional methods for extracting gold from ore; it is non-toxic to human health and environmentally friendly.

Aug 10, 2021

By C. Cristoffanini

A real-time transient pipeline simulation was used to model the operational pressure response in the concentrate and tailings pipelines of the Minera Los Pelambres copper mine in Chile. A high-fidelity simulator was needed to train the operators on safe operation of the pipeline for different scenarios. A simulator that solves the transient equations was used to dynamically predict the pressure and flow throughout the pipeline to provide real-time responses to operational changes such as opening or closing a choke valve, or sending a water batch. Slurry rheological properties were incorporated into the model. This paper presents the technical background of the pipeline simulation model and the study of slurry properties. The paper shows the results of the transient simulation for different operating scenarios such as start-up, shutdown and leakage, by presenting the hydraulic gradient curves for each case. Finally, the paper briefly presents how the simulator was connected to an emulated control system and used to train the operator, it demonstrates the most effective tool available to learn to resolve undesirable conditions.

Feb 23, 2014

By K. R. Miller

Thunder Basin Coal Company has two mines located in the southern portion of the Powder River Basin. 60-90 km southeast of Gillette, Wyoming. The mines are principally located on federal coal leases acquired in the late-1960's. Development plans for the Black Thunder Mine focused on dragline stripping, but environmental considerations during the mid-1970's made truck-shovel stripping the method of choice when the mine opened in 1976. In 1981, the Coal Creek Mine opened as the first dragline mine in the Gillette area of the Powder River Basin. The regional terrain is flat-lying with occasional clinker-capped hills. The mines are located on the Wasatch and Fort Union Formation contact. The coals are Paleocene in age and the deposits are structurally simple, dipping gently to the west. The seams are thick and are classified as sub-bituminous-C. The Black Thunder Mine, with its 21 m thick seam, is strategically located in the center of the highest heat value mining area of the southern Powder River Basin.

Jan 1, 1993

By Richard R. Klimpel

INTRODUCTION Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores such as cobalt, platinum, gold, silver, etc. Froth flotation is a physico-chemical process for separating finely ground minerals from their associated gangue material. The process involves chemical treatment of a finely divided (ground) ore in a water pulp to create conditions favorable for the attachment of certain of the mineral particles to air bubbles. The air bubbles then carry the selected minerals, called valuable, to the surface of the pulp to form a stabilized froth which is removed and recovered. The unattached gangue material remains submerged in the pulp and is either discarded or reprocessed. To obtain the adherence of the desired mineral particles to the air bubbles, at least two specific steps must occur: a hydrophobic (water hating) surface film must be formed on the particles to be floated along with a hydrophillic (water wetting) film on all other particles; and a controlled bubble surface tension interface must be maintained, allowing for high particlelbubble collision frequency and efficient attachment or sticking of the particle to the bubble once collision has taken place. In most flotation applications, the above two steps are controlled by chemical flotation reagents. The collector is a chemical reagent which produces the hydrophobic film on the valuable mineral particle and is the primary driving force that initiates the flotation process. The frother is a chemical reagent which influences the collision frequency and attachment efficiency of hydrophobic particles and air bubbles. Thousands of research papers and books have been published on the chemical theory behind sulfide mineral collectors, e.g., Fuerstenau (1962), Fuerstenau (1976), Fuerstenau, et. al. (1985), King (1982), Leja (1982) and Moudgil and Somasundaran (1987), This article will only address and summarize some of the more practical aspects of collector usage. The industrial scale practice of froth flotation in sulfide mineral concentration has changed little since the 1950's. For example, of the approximately 80,000 metric tons of sulfide mineral collectors used commercially (1980) in the free world, almost 98% were known and manufactured in some form 25 years ago. A very interesting and informative history of collector development has been given by Crozier (1984). In addition, the industrial scale practice of froth flotation applied to sulfide ores has proceeded since the 1920's with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully at an industrial scale for many years. As a result of the above environment which makes reagent cost/performance analysis difficult for new reagents, there is a strong tendency for the flotation operation to use, and reagent companies to supply, as cheap as possible raw materials and manufactured products that are quite general in application. In the last 20 years or so, there has been increasing technical effort to tailor make reagents for specific applications, but to date such work has had little commercial impact. It is clearly the hope of this author and others that this situation will change in future years as technology improves and pressure for improved flotation performance intensifies. This article is a condensation of collector usage trends quantified as part of a comprehensive industrially oriented applications program on froth flotation organized by Klimpel and coworkers (1979-1987) and as reported in various countries that participated in the program from 1978-1983. No attempt will be made to provide specific.

Jan 1, 1986

By W. M. Lewis

Product losses to tailings ponds have long been a source of frustration for the mining and utilities industries. The utilization -of the Lewis Econosizer to recover lost products has proven to be very cost effective through reduced acreage requirements, cleaning costs and increased production. The unit is successfully operating in coal, aggregates, industrial minerals, clay, fly ash, heavy minerals and many other ores. Utilizing an upward flow of slurry in a free settling environment, particles stratify within the unit according to settling velocities and are removed as sized products. Ultra fines or clarified water is removed off the top of the unit. The Econosizer requires no power and only minimal maintenance.

Jan 1, 1998

By C. J. Savage

Rio Tinto Minera, S.A. operates in Southern Spain, at one of the most ancient mining sites in the world, using advanced computerised mine planning. This paper describes the development and application of the mine planning systems to the copper and gold/silver operations. It briefly covers the hardware configuration, and the advantages and improvements in mine planning achieved. The system's application started with the long term mine planning of Cerro Colorado (open pit) copper mine and was gradually extended to cater for the medium and short term planning requirements of the other operations of the Company. The base of the system is a mineral inventory established by the combined use of the geology and geostatistical methods, and compatible with the mine planning requirements. The planning system has three major components: one used for open pit design and long term mine planning, another used for blast evaluation and finally one used for short term mine planning. Recently, a fourth component has been added to the system for reconciliation between predicted and actual tonnages and grades. There is common data file transfer throughout the system.

Jan 1, 1986

By Gary Schaffer, Anthony Stentz

Surveying of mines is a necessary step in coal mining to assemble maps which are used for tracking progress in the development of the mine and to plan future coal removal. A first approach for automatically building high-resolution two-dimensioml maps of underground coal mines is presented. The technique assembles laser rangefinder scans obtained from several locations within the mine into a consistent global map of the mine. Each range scan comprises thousands of data points collected in one second, thereby achieving higher resolution and much faster measurement compared to a human using a transit. The raw data (range scans) are processed to fuse them into a consistent representation. This paper describes a first approach to automated surveying and presents initial results of merging range scans. Improvements to the scan-merging algorithm are proposed.

Jan 1, 1993

By C. L. Karr

The efficient management of the distribution of goods and services is important throughout the minerals industry. From the scheduling of processing plant operations, to the routing of work crews in mines, to the planning of product development, vast amounts of time, energy, and money are wasted due to poor planning and scheduling. Thus, the U.S. Bureau of Mines is investigating computational algorithms that can be used to minimize the economic losses related to scheduling and allocating resources. Although there is commercial software available for tackling many scheduling problems, there has been little relief provided for solving the difficult traveling salesman with time windows problem (TSTW). The TSTW problem is a "derivative" of the classic traveling salesman problem, and can be used to minimize the distance traveled by vehicles or personnel to visit all points on a tour, with the additional constraint that each point on the tour must be visited within a specified time window. This paper is a survey of published work in which genetic algorithms have been used to efficiently solve the traveling salesman problem and its more difficult derivative, the TSTW problem. A genetic algorithm is a search algorithm based on the mechanics of natural genetics, and has been used to solve a broad spectrum of engineering optimization problems. Results indicate that the versatility, searching power, and simplicity of genetic algorithms can be used to provide substantial improvement in the area of scheduling and resource allocation.

Jan 1, 1994

"Increasing demand and market economics have pushed the mining industry to adopt improved mining practices and minimize losses. Simulation, in this regard, has proved to be an efficient tool to help in decision making purposes. We present the development of a discrete event simulation model for a large-scale open pit mine to run experimental scenarios for near optimal decision making. A mixed integer linear goal programming (MILGP) optimization model is also presented for shovel allocation optimization. The mathematical model will be coupled with the simulation model at the dispatching stage for shovel allocation optimization and thus it will act as the link to optimal short-term schedule to assist in achieving better mine plan compliance across short-term and operational planning time horizons. The main contribution of this work so far is the development of the MILGP model and development, implementation and verification of the simulation model on a large scale oil sands open pit mine case study. The results obtained so far are promising and have been validated against the historical data of the mine, proving the applicability of the model for experimental scenario analysis. INTRODUCTION It is essential for mining operations to adopt efficient operational methods and technologies to cope with market demand and economics. Mining operations, on the other hand, being capital intensive, find it risky to bring in any changes. Simulation is a tool that can help in this regard for better decision making purposes with an improved and quantitative measure of confidence. A true representative model that satisfies the objectives set for the simulation is essential to achieve its applicability for decision making purposes. A similar simulation model is presented in this paper for analyzing the operational KPIs of a large scale oil sand open pit mine with truck-shovel operations. This paper is aimed at providing an overview of the development of the model and the statistical outcomes validating its applicability for experimental scenario runs and thus for better decision making purposes. A mixed integer linear goal programming (MILGP) optimization model is also presented in this paper that acts as an upper stage in a multi-stage dispatching system. The optimization model is proposed to be linked with the dispatching logic in the simulation for optimal shovel assignments and target productions by reading available mining faces directly from the short-term extraction schedule. This model is aimed at bridging the gap between operations and short term extraction schedule; and may help achieve better compliance between the two."

Jan 1, 2015

By A. Redfern, B. G. D. Smart

The ultimate objective of the development work presented in the paper is to devise an appropriate method for relating powered support specification to geological conditions and mining practice, thus enabling the longwall method of coalmining to be successfully implemented throughout the varied coalfields of the world. The paper begins with a review of various methods previously used to determine support rating, each method being analysed with regard to its source, the logic and theory which constitute the method, and subsequent recommendations. An alternative approach is then proposed, the Powered supports being considered to be one of three foundations, sharing load with coal ahead of the faceline which acts as another foundation, and the waste behind the supports which acts as the remaining foundation. The load/deflection characteristics of the coal and waste, which in turn are related to geological conditions and mining practice, are shown to affect the load transfer on to and hence the specification of the powered support. In particular the characteristic of the waste foundation is shown to be affected by the caving mechanism, an alternative form to that mechanism accepted for British conditions being proposed and designated "parting-plane-controlled" caving. A finite element solution for a beam on elastic foundations was used to translate the above concepts into numerical results, these results being compared with data from Indian and Chinese operating conditions. The Indian case study examines the effect of using a conventional chock type of support in a one-web back mode when mining towards a roof break generated ahead of the face, while the Chinese case study compares measured subsidence over a longwall with "blocky" roof conditions with the model results. The comparisons are encouraging, suggesting that the approach used is worthy of further development.

Jan 1, 1986