Search Documents

Coal has traditionally been an integral part of life in Kentucky. Coal mining produces a large part of revenue for the Commonwealth of Kentucky and provides a significant number of jobs to the residents of eastern (less in western) Kentucky. Recently, however, the coal industry of Kentucky has had to endure many hardships. The Clean Air Act set forth sulfur dioxide emission standards which have severely affected much of the coal mining industry in Kentucky, because much of the coal mined in Kentucky has a high sulfur content. In this paper, the background around the effects of Clean Air Act on the coal industry is introduced. The economic and social effects of the Clean Air Act on the Kentucky coal mining are addressed.

Jan 1, 1993

By Ralph J. Holmes

INTRODUCTION Although sampling techniques used by the mineral industry continue to improve, sampling is still an area which is often neglected. Frequently, sampling and sample preparation requirements are left to personnel who do not fully appreciate the significance and importance of sampling. Consequently, plant evaluations are often based on seriously biased samples, leading to mass balance problems and incorrect assessments of plant performance. The basic rule for correct sampling is that each particle of ore or concentrate must have an equal probability of being collected and becoming part of the final sample for analysis. If this is not the case, bias is easily introduced and the sample is not representative. For example, when ore is travelling on a conveyor belt, the lumps may come to the surface. Consequently, a grab sample taken from the top layers only will contain a greater proportion of lumps, i.e., the sample is biased. There seems little point in making major investments in precise analytical equipment, if the sample provided to the analytical laboratory is not representative in the first place. This paper describes the sources of plant sampling errors, reviews the methods of estimating their variance, presents some worked examples, and provides some practical advice for reducing sampling errors and their variance. SAMPLING BASICS It is generally accepted that the discharge point of an ore or concentrate stream is the most suitable sampling location. The stream can be intersected at regular intervals, and representative samples, referred to as increments, can be obtained by taking a complete cross-section of the ore stream. On the other hand, sampling devices that take part of the stream on an intermittent or continuous basis, e.g., a bleed from a pipe, may introduce serious bias, and should be avoided at all cost. Increments may be taken at completely random times or tonnages during the sampling operation, in which case it is called "random sampling". However, as shown below, random sampling results in the largest sampling variance, so it is preferable to divide the ore or concentrate stream up into strata of equal time or mass and take one increment from each stratum. This operation is called stratified sampling and may be either systematic sampling, in which increments are taken at the same point in each stratum, or stratified random sampling in which the increments are taken at random within each stratum. Systematic sampling results in the smallest sampling variance, provided periodic variations in quality or quantity are not present which may coincide with, or approximate to, any multiples of the proposed sampling interval. In such cases, it is strongly recommended that stratified random sampling within fixed time or mass intervals be carried out.

Jan 1, 1991

By Y. Kurokawa, R. Kurosawa, I. Iwata, I. Fukuoka, N. Sugita

INTRODUCTION The Ningyo-toge Mine is located in the western part of Honshu, about 800 km from Tokyo. Since the discovery of uranium ore deposit at Ningyo-toge in 1955, different kinds of mining and milling tests have been carried out. A new pilot plant of milling and UF6 conversion is also being under construction. Operations are scheduled to start by the end of this year. In 1979, the uranium enrichment pilot plant was constructed at Ningyo-toge and test operations have started. Thus, the Ningyo-toge area is assigned to undertake the Research and Development of the upstream of the nuclear fuel cycle in Japan. PNC has been strengthening its security measures more than ever. This paper will focus on the disposal of wasted material, especially on the disposal of heap leaching residue, in Japan. URANIUM ORE DEPOSITS The uranium of the Ningyo-toge Mine is characterized genetically by epigenetic sedimentary type deposits. They occur in the host rock of Neogene tertiary fluviatile conglomerates and sandstones which unconformably overlies the Mesozoic-Palaeogene granitic basement covered with lucustrine deposits and volcanic ejecta. More than 12 deposits have been found over the area of approximately 160 km2, and distribution of the deposits are strongly controlled by the so-called channel structure, probably remnants of paleo-streams on the denudation surface of the underlying grantic basement. Each ore body has different shape and dimension respectively, but about 2-3 meters thickness with the average grade of 0.05-0.2% U308 is common feature of the ore bodies. The ore is soft and loose, and it is composed of common rock forming minerals of allogenic origin and their altered products. The chemical composition of the ore depends on the constituents of the country rocks or the pebbles. A primary mineral, ningyoite and secondary mineral, autunite are major ore minerals, although three primary tetravalent minerals and thirteen secondary hexavalent minerals have also been detected. MINING EXPERIMENT Since 1959, various types of underground mining tests have been carried out at Ningyo-toge Mine. The room and pillar method was safe and simple, although the uranium ore recovery was below 70%. After experiment of the retreating long-wall method and slicing mining method, it was found that the modified long wall method was the most appropriate for the underground mining of the Ningyo-toge uranium deposits. This method was completed successfully to increase efficiency up to 2 or 3 times, as compared to conventional methods. MILLING EXPERIMENT In 1964, a small test mill was constructed at Ningyo-toge, and a milling experiment using the Ningyo-toge uranium ore was started. Re-modelling of equipments and improvement of the process lead to the establishment of the technique of the so-called wet process, and produce UF4 directly from the ore. The flow diagram is shown in Fig. 1.

Jan 1, 1981

By M. B. Freeman

Acrylic polymers have been found to be effective dispersants and stabilizers in a wide variety of mineral processing applications including rheology control in concentrated slurries. This paper will describe these low molecular weight, water-soluble polymeric dispersants and provide a basis for how they function in concentrated slurries based on computer molecular modeling and applications results. Data on homopolymers as well as copolymers of acrylic acid will be presented to demonstrate the optimization of a polymeric dispersant in preparing high solids slurries of inorganic materials such as kaolin, calcium carbonate, lime, and magnesium hydroxide.

Jan 1, 1996

By Ralph H. Knode, Stephen P. Collings

INTRODUCTION The Crow Butte uranium deposit is located in northwest Nebraska near the town of Crawford (Figure 1). The deposit was discovered during the fall of 1980 by Wyoming Fuel Company, operator of the Crow Butte Joint Venture. The Crow Butte Joint Venture is owned 50 percent by Wyoming Fuel Company, a subsidiary of KN Energy, Inc.; formerly Kansas-Nebraska Natural Gas Company, Inc., 40 percent by Ferret Exploration Company, Inc., and 10 percent by First Exploration Company. A preliminary announcement made in January 1981 indicated a "probable potential" reserve in excess of 25,000, 000 pounds U303. Drilling during 1981 and 1982 confirmed these reserves and indicated the presence of more than 30,000,000 pounds U308 having an average grade in excess of 0.25 percent U308. Wyoming Fuel Company was initially attracted to the area in 1978 by favorable regional geology for sandstone uranium deposits and weak radioactivity noted in regional oil and gas holes. Exploration drilling began in 1979 following the formation of the Crow 3utte Joint Venture. Drilling has continued up to the present, at which time the Joint Venture is ready to proceed with a pilot scale solution mine. Environmental baseline data have been acquired and the permit applications for the pilot scale mine have been submitted to the Nuclear Regulatory Commission and to the applicable state agencies in Nebraska.

Jan 1, 1984

By Sean Gallagher, Thomas G. Bobick, Richard L. Unger

This paper describes research by the Bureau of Mines on alternative materials-handling strategies for reducing the costs and incidence of back injuries in low-seam coal mines. Strategies recommended for redesigning materials-handling tasks include elimination of tasks, mechanization of tasks, and matching lifting tasks to the physical capabilities of underground miners. The report also discusses other methods that can be used by management to reduce the costs associated with back injuries. More detail can be found in Bureau of Mines Information Circular 9235 (Gallagher et al. 1990).

Jan 1, 1992

By R. P. Stahura

In many ways, conveyors are the lifeline of mining and processing operations. Like arteries in the human body, they continuously supply materials to and carry finished products and waste away from vital on-going operations. And like arteries, when the conveyors are running with less than maximum efficiency and productivity, it spells serious trouble for the operation's overall health. Inefficient conveyors suffer carryback, leading to the build-up of materials on idlers and other expensive components. They spill and leak material at loading zones and conveyor transfer points, causing accumulations that can damage the belt, wear moving components, and increase both clean-up labor and maintenance expense. They wander or mistrack, spilling material and endangering personnel and conveyor components including the belt itself. And through these inefficiencies, they multiply the operation's hidden costs. These added expenses are created in lost production, increased downtime for service and maintenance, and the cost of the replacement of prematurely worn equipment. In addition, the attitude that inefficiency is "good enough" is recognized elsewhere in the organization; as a result, other departments relax or operate at less than peak performance. Quality goes down and with it employee morale.

Jan 1, 1992

Many of the deeper ore reserves in current gold operations as well as new gold deposits consist of refractory ore types. As process development for these mineralizations remains time-consuming and costly, minimization of exploratory testwork and the early identification of feasible process routes is critical. Since most of the processing parameters are related to the mineralogy of the ore (Marsden & House, 1992), thorough mineralogical analyses during exploration and development phases have become a technical and economical requirement. The determination of mineralogy-related processing parameters and especially the gold mineralogy is even more important for these ore types because refractory gold ores consist of many transitions from partially leachable to totally refractory. In addition to sulfide and gangue encapsulation, various other refractory conditions may exist. Together with accessory mineralogical detriments (e.g., alteration/ slimes, reagent consumers, scale formation, mineral preg robbing) they may complicate process selection and hamper optimal plant operation.

Jan 1, 1993

INTRODUCTION Automatic controls are devices that assist operators by performing routine tasks faster and better than they could alone. Great strides have keen taken in the development of new processes and bigger machines to improve productivity, but these developments created the need for increased protection of machinery and labor. The new production-line techniques, or continuous processes developed, resulted in routine and, frequently, demoralizing jobs. The human race is not constituted mentally to perform routine operations. Devices were needed also to gather information automatically and perform routine functions. High-capacity plants incorporating large equipment

Jan 1, 1985

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by the National Institute for Occupational Safety and Health's Pittsburgh Research Laboratory. Investigated were a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal-extraction side of the longwall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. In laboratory experiments and in a longwall field evaluation, the translucent mesh barrier was shown to provide notable dust-control effectiveness for a distance of up to 60 m downstream of the shearer, provided that the mesh barrier remained relatively parallel to the airflow. The staged spray barrier system showed marginal dust-control effectiveness in the laboratory and, therefore, was not field tested.

Jan 1, 2000

By Steve Van Kouteren

Filters and absorbents purify, clarify, and clean many types of liquids by removing solid particles. In addition, absorbents provide a convenient way to handle liquids and to clean up liquid wastes or spills. Filtration or absorptive processes are accomplished either in a mechanical way, as in absorption and filtration, or in a chemical way, as in adsorption. In filtration, minerals and rocks used as filter mediums are extensively utilized in applications requiring the filtration of high volumes of liquids. End use applications include liquid food products, waste waters, petroleum and chemicals, and drugs and pharmaceuticals. Upon closer examination of all of the materials used as filters and absorbents, industrial minerals and rocks represent only a small proportion of the total amount, as shown in [Fig. 1] (Rees, 1991). Given all the industries that use these minerals, most of the volume is concentrated in a few major end-use markets. Within these major end-use markets, a handful of minerals account for most of the total volume and value. The focus for this chapter will be to discuss the industrial minerals and rocks used as filters and absorbents in the most important markets. The selection of the minerals and markets to review is solely based on the total volume of material used and in special cases, those where the value of the market and material is high. The major materials include diatomite, perlite, sand, gravel, and such specialty clays as montmorillonite and attapulgite. These materials are mainly used for the filtration of food, chemical, and petroleum products. In addition, they are used as absorbents for pet litter and oil and grease spills, and as carriers for pesticides and fertilizers.

Jan 1, 1994

By J. Gallagher

Henderson Mine has been transporting molybdenum ore using a rail haulage system for the past 21 years. Due to the age of this system, limited performance, and obsolescence, a capital investment decision was imminent. Henderson used this opportunity to evaluate other transportation methods and continuously improve their mining practices. These efforts resulted in a new mine plan for Henderson, which ensures that Henderson will continue to supply high quality molybdenum into the 21st century. This paper will discuss the dramatic changes taking place at the Henderson Mine as a new production level is mined. These changes include the installation of an underground crushing, conveying, and truck haulage system, as well as increasing the scale of the panel caving process. Each of these topics will be discussed, as will their rock mechanics and material flow implications.

Jan 1, 1998

By W. S. Hannan

History Leaching of sulfide ore was first attempted by the Phelps Dodge Corporation about 1900 at Bisbee, Arizona, when Dr. James Douglas conducted experiments in an attempt to apply the leaching techniques then in use at Rio Tinto, Spain. Although this initital attempt was unsuccessful, research work was continued which culminated in successful leaching operations at Tyrone, New Mexico, in 1917 and at Bisbee beginning in 1920. Leaching has continued intermittently since that date, with material from the Lavender Pit being leached today. The Lavender Pit Leach Dump Stripping for the Lavender Pit was started in 1951, with mining operations on stream in 1954 and continuing to the present. All material removed from the pit has been classified as waste, leach material, milling ore, or direct smelting ore, depending upon grade and degree of oxidation. Lavender Pit leach material has been stockpiled in a single dump, called No. 7 Dump. This dump covers an area of approximately 135 acres and average about 300 feet in height. The dump has been deposited over a period of 20 years by truck haulage and contains several layers, each of which has a permeable boulder layer at the bottom and a compacted layer at the top. Leaching of Lavender Pit material was started in 1956 and has proceeded simultaneously with dump construction. Former leach pond areas and haulage surfaces have been ripped with D-9 tractors before deposition of succeeding layers of ore.

Jan 1, 1972

By Péter Siklósi, János Zámbó, Károly Solymár

It is fundamentally important to evaluate bauxites in a realistic, commercial way on the basis of the processing technology both for the supply of existing alumina plants and for the designing of new ones. The evaluation system developped by ALUTERV-FKI consists of chemical, mineralogical, texture and technological testing. The commercial value of bauxites is basically determined by their available alumina content and the caustic soda consumption required for their processing. However, their contaminants have to be taken into consideration, too. The commercial value of bauxites also depends on the processing technology and their possibly unfavourable chemical and mineralogical composition can be /at least partially/ compensated by R&D efforts. The selection of the optimum processing technology and the effects of further developing the same are demonstrated on monohydrate bauxites containing goethite and carbonates. Some of the technological solutions /desilication or deironing of bauxites, hydrothermal treatment of the digestion residue / make at the same time possible the complex processing of the bauxites, the profitable utilization of their main components.

Jan 1, 1984

By M. Manrique, E. E. Vidal, I. Accorsi, P. R. Taylor

Various pyrometallurgical methods for treating ilmenite and zircon concentrates are reviewed. Laboratory experiments using a thermal plasma reactor were performed to evaluate the conversions of ilmenite to TiC or TiC-Fe and zircon to ZrC or ZrC-SiC. Results are examined and possible processing routes are identified.

Jan 1, 1999

By E. T. Tuzcu

Microscale information about single particle fracture can be incorporated into the macroscale model of the whole size reduction process in the mill. The ultrafast load cell (UFLC) device provides a substantial amount of information about fracture characteristics of a particle under impact loading. UFLC captures high-resolution compressive force signals during particle breakage. The measurement of the compressive force at the instant of fracture of the particle allows computation of a number of comminution-related particle properties, as well as the energy absorbed during fracture. In the current study, limestone particles 50 mm in size were fractured to obtain specific fracture energies. Then, based on the experimental data, two models were proposed to quantify the fracture process. The specific fracture energy distribution of the particles in the range of 6 to 50 mm was defined by the well-known Weibull distribution. The other model is a probabilistic fracture model. This model is a link between energy events occurring in a grinding mill and the breakage rates of particles. The impact energy spectra or energy events occurring in a grinding mill can be obtained with a discrete element method (DEM) simulation. One can model the breakage rates of the mill material by combining the energy spectra with the probabilistic fracture model. This novel approach for the modeling of breakage rates via DEM and UFLC is shown here.

Jan 1, 2011

By E. T. Tuzcu

Microscale information about single particle fracture can be incorporated into the macroscale model of the whole size reduction process in the mill. The ultrafast load cell (UFLC) device provides a substantial amount of information about fracture characteristics of a particle under impact loading. UFLC captures high-resolution compressive force signals during particle breakage. The measurement of the compressive force at the instant of fracture of the particle allows computation of a number of comminution-related particle properties, as well as the energy absorbed during fracture. In the current study, limestone particles 50 mm in size were fractured to obtain specific fracture energies. Then, based on the experimental data, two models were proposed to quantify the fracture process. The specific fracture energy distribution of the particles in the range of 6 to 50 mm was defined by the well-known Weibull distribution. The other model is a probabilistic fracture model. This model is a link between energy events occurring in a grinding mill and the breakage rates of particles. The impact energy spectra or energy events occurring in a grinding mill can be obtained with a discrete element method (DEM) simulation. One can model the breakage rates of the mill material by combining the energy spectra with the probabilistic fracture model. This novel approach for the modeling of breakage rates via DEM and UFLC is shown here.

Nov 1, 2011

By Kunio Hashimoto

The conventional troughed belt conveyor system is the most widely used form of equipment for transporting bulk materials in the world today. The reason is not only because it is possible to transport a great deal over a long distance when compare to other types of equipment but also due to its greater economic efficiency and low initial and running costs. When dry, powdery materials and liquid materials are being conveyed, there are enclosed transport methods such as flow, case, air-slider and pipe line. In addition to features of the belt conveyor, a system employing a pipe line to transport dry powdery and liquid materials has always been considered an ideal method. This has been brought into reality through the Pipe Conveyor Sys tem.

Jan 1, 1984

By A. J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of steel wire ropes. Steel wire ropes are very suitable for mine hoisting due to their high strength and durability, but have the negative characteristic of a low strength/weight ratio. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength/weight ratio of synthetic ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application.

Feb 23, 2014

By M. I. Brittan

A technique has been developed that analyzes routine mill operating data to determine the key operating parameters responsible for gold losses to tails. These parameters represent the prime operating variables having a dominant effect on gold recovery. The technique quantifies these effects for the specific plant being analyzed, providing a tool to optimize recovery and costs and so enhance the mine?s cash flow. The quantitative relationships generated will be different for each ore and plant: every case is site-specific and has to be treated on its merits. Examples are provided to illustrate the considerable metallurgical and financial benefits which can be realized from optimization. The examples are taken from case studies of mills in four major gold mining districts of the world.

Jan 1, 2010