Search Documents

By Ruston A. Ford

This paper reviews the development of the David Bell Mine, from early exploration, through discovery, construction, start-up, underground development, and production. Details are provided regarding the mine development, the mechanized cut and fill stope production, the proposed long-hole stoping with delayed backfilling mining method for the lower levels and the cyanide leach carbon-in- pulp concentrating process. The mine development remains on schedule and under budget with results very much as predicted in the feasibility study.

Jan 1, 1987

By X. Li, J. C. Stankus, J. Ma, H. Chen

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult, because a slope will transverse through many types of strata. Over the last few years, Keystone Mining Services LLC, an affiliate company of the Jennmar Corporation, has developed a new methodology designated the “Stress, geologic and support design system (SGS).” The method analyzes the stress, geology and support design for a mine slope. The method has been successfully applied in various new slopes across the United States, and ground control plans developed using SGS methodology has helped coal companies successfully pass review and/or hearings by state and federal regulatory agencies. With a case application in the U.S. Midwest, this paper details and demonstrates the main concepts of the methodology, including (1) analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) primary and supplemental support design; (3) long-term support design in the form of steel square sets or arches and (4) validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By James D. Bliss

Evaluation of data for three engineering variables-absorption, bulk specific gravity, and freeze-thaw durability (350 cycles)-was made for quarries in carbon- ate rocks in Oklahoma that supply aggregate. It was found that lower Paleozoic carbonate rocks (Cambrian through Devonian) are likely to make a better quality aggregate than upper Paleozoic (Mississippian to Permian) carbonate rocks. In addition, freeze-thaw durability can be forecast from absorption and is exemplary for lower Paleozoic carbonate rocks.

Jan 1, 1999

By H. Akgun, J. J. K. Daemen

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. Presented in this paper are the results of push-out tests on two types of expansive cement grout plugs emplaced in rock salt. The average interface shear strengths range from 2 to 12 MPa. Peak shear stresses (assuming an elastic stress distribution along the interface) are up to eight times higher. Dissolution along the interface may be enhanced by clay inclusions in the salt and appears to reduce bond strengths. Application of the results to the design of plugs for larger openings (e.g., shafts, drifts, or boreholes) is discussed.

Jan 1, 1995

By L. G. Hendrickson

Direct-reduction processes for converting iron ores to metallic iron in the solid state have been available for some time; and whenever scrap becomes expensive, there is a new wave of interest in these processes. It is well established that direct reduction, coupled with electric-furnace steelmaking, is a technically viable method for making steel and in some circumstances is economically competitive with the conventional blast-furnace--basic-oxygen-process (BOP) route to steel. This raises a number of interesting questions, several of which could be of great interest to the coal and ore mining industries. For example, what are the quality requirements of the raw materials for direct-reduction--electric-furnace steelmaking? Would they be different from the present requirements for blast-furnace--BOP steelmaking? Other questions relate to how much steel will be made by the direct-reduction route in the future. The quality questions can be discussed with a fair degree of certainty, but a prediction of the amount of steel that will be produced by the direct-reduction--electric-furnace route is beyond the scope of this paper. However, an attempt will be made to identify some of the factors that will influence whether there is a swing to direct reduction and the rate at which it may occur.

Jan 1, 1978

By Chris Mills

El papel de la separacion gravimétrica en la industria minera es brevemente considerado en perspectiva. Las pruebas e intentos de laboratorio y mineralógicas para el diseñio de los procesos gravimetricos son examinados poniendo especial énfasis en la selección de la tecnologia del proceso. Es tratado y comentado el material disponible en equipos para pequeña escala y trabajo de pruebas-piloto, particularmente en relación a la escalacion y a la adquisición de datos precisos y fiables. El transporte del comportamiento de los datos desde la planta piloto a la planta a escala es igualmente explicado. Son resefiados todos los tipos de equipos a escala total existentes para la separacion gravimétrica, poniendo de relieve las unidades de alta capacidad. Es considerada la disposicion de la planta y la seleccion de 1os equipos auxiliares.

Jan 1, 1982

By M. Guzman, M. Romero, S. Bravo-Thais, M. Flores

The phytoremediation method is proposed to recover valuable metals from polluted soils. In this sense, the objective of this research is to determine if it is possible to use native plants in the recovery of precious metals from abandoned mining liabilities. The tailings samples containing Au and Ag were acquired from the northern region of Peru. Two native plant species, Stipa Ichu and Cortaderia Nitida, were used. Results show that Au was recovery around 19% (1.52 mg/Kg) and 25.43% (1.78 mg/Kg) by using Stipa Ichu and Cortadeira Nitida, respectively. Besides, Ag had a better recovery in the Stipa Ichu reaching a value of 6.83% (0.628 mg/Kg); in contrast, Cortadeira Nitida had an efficiency of 3.6% (0.814 mg/Kg). Bioaccumulation, bioconcentration and translocation factors were calculated by determining the concentration of precious metals in the roots and aerial parts of each plant. Results show that Stipa Ichu had a greater capacity of hyperaccumulated Ag compared to Au; while Cortaderia Nitida tended to have a better performance for Au. In conclusion, both plants are recommended for phytoremediation of mining liabilities.

Feb 1, 2023

By Al. Valero

This paper quantifies in universal units (energy units), the annual decrease in the mineral endowment of the planet. This is done for some important extracted non-fuel minerals, namely aluminium, cobalt, chromium, copper, gold, lead, uranium and zinc and is compared with the depletion figures of conventional fossil fuels. The results of this study reveal that each year, the decrease of the global non-fuel mineral bonus provided by Nature is 2 to 3 orders of magnitude greater than the loss associated to the burning of fossil fuels. Particularly for 2008, the depletion in mineral wealth of the studied commodities was about 20 times greater than that of fossil fuels. The assessment methodology is based on the Second Law of Thermodynamics. It quantifies the useful energy (exergy) required to concentrate a mineral from a completely dispersed state in the crust, to the conditions of composition and concentration found in the mines. Exergy can be a useful measure for quantifying the mineral depletion caused by man, as it takes into account the main physical features that make minerals valuable: composition and concentration. This analysis enhances and puts numbers to the importance and necessity of material reuse and recycling.

Jan 1, 2011

By R. L. Lewis

A simple method for estimating the steady-state water quality of a pit lake is presented. The steady-state concentration of a conservative chemical constituent in a pit lake is shown to be a simple function of inflow rate, evaporation rate, and inflow concentration. An analytical method is presented for estimating the equilibrium ground water inflow rate for use in water quality predictions. The time required to reach chemical steady-state is estimated using an iterative mass balance model. Mine operators should find the methodology useful for planning and screening-level regulatory applications where conservative estimates of pit lake water quality are desirable.

Jan 1, 1998

By Paolo M. Brion, Z. Bade Sozer

"The Bypass Tunnel has high head conditions ranging from a minimum of 600 feet (183 m) under the Hudson River to a maximum of 875 feet (267 m) on the west side. The ground cover ranges from 425 feet to 900 feet (130 to 274 m). A two-pass lining is designed for the Bypass Tunnel. The bolted, gasketed precast segments carry the temporary hydrostatic and permanent ground loads. After the tunnel is put into service, the design assumes that the final lining, which varies from reinforced concrete to reinforced concrete with steel interliner, will carry the permanent hydrostatic loads. The design head for the segments is assumed at 775 feet (236 m), and the internal operating pressure head is around 1,200 feet (366 m). This paper discusses the design hydrostatic head and different load conditions considered for the segments, the load sharing between the segments and final lining, and the means employed to control water and hydrostatic pressure. PROJECT BACKGROUND The Rondout-West Branch Tunnel (RWBT), a segment of the Delaware Aqueduct, was built from 1937 to 1944 and provides about 50% of New York City’s total water supply. Monitoring and tunnel operations have shown that the RWBT is leaking up to 35 million gallons per day (MGD) (132.5 million L/day). In particular, two locations have been identified as areas of concern: Roseton and Wawarsing, as shown in Figure 1. The Wawarsing reach of the aqueduct will be repaired with an extensive grouting program when the RWBT is unwatered. However, because of the extensive nature of the leakage in the Roseton area, a Bypass Tunnel will be constructed to divert the flow around this area."

Jan 1, 2016

By R. Bruno

The problem of testing different production strategies has been studied in relation to reserves selection and a computer programme for ore production management has been developed. The case study presented concerns an underground rock salt mine in Sicily with different product lines and variable ore characteristics. A geostatistical block model of the deposit was constructed on the basis of the physical and chemical parameters that ultimately determine the type of end-product in operations according to different selection strategies were simulated using the model and taking account of both technical and 'commercial constraints. The structure of an ore production management programme running on a PC to select both the mining unit and the end-use of the ore is described.

Jan 1, 1989

By C. Anastasiadis

The wettability of sandstone was investigated using the technique of dielectric spectroscopy in the frequency interval 1kHz-1MHz. The natural wetness of the material was modified to get two different sets of samples, one with sea-water wetness and the other with crude oil wetness. Measurements showed that the electric responses of water-wet and crude oil-wet samples were markedly different beside the fact that the dielectric response of both groups of samples obeys a general fractional power law. The dispersivity, of the complex permittivity component that expresses the material loss with respect to the electric field was found to be the most suitable parameter to check the wettability of the samples.

Jan 1, 2005

By Jon Holder, Brann Johnson

Pore-fluid/rock chemical interactions on both short and long time scales can produce significant pore structure and mineralic changes that can markedly alter transport properties, such as fluid permeability. The introduction of the chemical factor requires modification of experimental systems and methodologies developed for measurements in which chemical effects are minimal. Particular attention must be given to temperature effects, fluid chemistry, fluid/rock reactions and kinetics, fluid flow rate, and fluid/experimental-system reactions. The ability to obtain very low, steady flow rates at constant fluid pressure is important for study of some fluid/rock systems. Minimization of metal corrosion is of paramount importance and requires choice of proper metals, such as titanium, and certain Ti-alloys and Ni-alloys. In this paper, we briefly discuss the relevant chemical factors affecting system and experimental design. The primary focus, however, is on the characteristics of highly corrosion resistant metals, thermal and chemical resistant jacketing materials, and the attributes and limitations of various flow-rate and back-pressure control systems and flow-rate measurement systems.

Jan 1, 1986

By A. B. Cecala

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U.S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1993

In underground coal mining, one of the biggest challenges is spontaneous combustion, which will not only present safety hazards but result in reserve losses as a result of burnt coal. The released heat coupled with other combustible gases commonly encountered underground will significantly increase the risk of explosion. In this paper, three-phase foam as an environment-friendly fire fighting agent composed of nitrogen, water and fly ash is introduced. The nitrogen facilitates inertization of the fire zone; the water helps cool down the fire and the fly ash can closely cover the coal to isolate the oxygen. What's more, the fly ash and the foaming agent are good free radical absorption. The comprehensive merits mentioned above make three-phase foam quite effective in quenching spontaneous combustion. Experiments indicate that three-phase foam can significantly slow down the temperature rise of coal during oxidation. The comparison between slurry and three-phase foam shows that the latter one is capable of flowing upward in the porous media so as to extinguish the high-point fire and concealed fire.

Jan 1, 2011

By James G. Tilton

Subsidence resulting from mining operations, has been the object of sporadic study for many years. Reports have shown that subsidence has ranged from minor settlement detected only by precise measurements to great slips where buildings are destroyed, roads disrupted, and large fissures opened at the surface. For years, a controversy has raged over the question of whether there is a positive or negative angle-of-draw. None of these questions can be given a flat answer for the variables controlling, subsidence are infinite. Generalizations can be made for various situations and areas but some means of control must be executed.

Jan 1, 1966

By J. Girard-Dwyer, J. Johnson, J. Whyatt

The choice of fragmentation method is one of the most fundamental aspects of mine design, and often has a major impact on the safety and economic viability of an operation. Almost exclusively, underground mining operations rely on either mechanical excavation or drill and blast techniques to extract rock. Each of these fragmentation methods has distinct advantages and disadvantages, and each is appropriate, and economic, for different mining conditions. However, the choice of fragmentation method can have a pronounced effect on the amount of damage created in the rock mass surrounding the opening. This paper reviews a number of case studies where both mechanical excavation and traditional drill and blast were used in underground mines. Ground support requirements in the mechanically excavated areas are compared to the support requirements in the blasted sections in order to demonstrate the potential safety and cost benefits of the various fragmentation methods.

Jan 1, 2003

By I. Ward, E. Milosavljevic, M. Botz

"The silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide in leach solutions that contain primarily free cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method overestimates the concentration of free cyanide and underestimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric (MP) titration method for determining WAD cyanide that overcomes issues associated with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper, and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, analytical results obtained with the new MP-WAD method were found to be within about ±5% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.IntroductionThe silver nitrate titration method is widely used to estimate the concentration of cyanide in leach solution for purposes of cyanidation process control. Cyanide determined by silver nitrate titration is commonly referred to as “free” cyanide, but frequently should be referred to as “titratable” cyanide. By definition, free cyanide is the sum of the concentrations of aqueous hydrogen cyanide HCN(aq) and the cyanide anion CN- (ASTM, 2010). Titration will only yield a reasonably accurate measurement of free cyanide when metal-cyanide complex concentrations (e.g., cadmium, copper, mercury, nickel, silver and zinc) in solution are low. In other words, titration will only yield a reasonably accurate measurement of free cyanide if the solution primarily contains free cyanide."

Jan 1, 2015

By S. C. Sun

A study(1) on the sulfuric acid extraction of alumina from some Pennsylvania ferruginous clays indicated that the published electrolytic method(2)(3) seems to be more efficient than the known chemical methods (4-9) for removing iron from the leach liquor. The main disadvantages of the chemical methods are the consumption of excessive amounts of reagents and/or the precipitation of prohibitive amounts of aluminum. In the electrolytic method, iron is deposited on the mercury cathode, while aluminum is not and remains in solution. This method, however, had been handicapped by the lack of an effective and economical way to purify the contaminated mercury cathode.(7)(l0). Described herein is a scheme for cleaning the mercury cathode, and for recycling the clean mercury back into the electrolytic cell. Armed with such an apparatus, the effects of applied potential, temperature, and operation time on the electrolytic separation of iron from aluminum sulfate solutions were determined. For the sake of comparing results, a term, removability, was coined to represent the percentage of iron amalgamated per unit height of electrolyte (cm.), per unit surface area of cathode (cm.2), per unit of operation time (second).

Jan 1, 1968

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ?Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions became the post-event conditions. ?Search for evidence that either denies or supports the various hypotheses. ?Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009