Search Documents

By M. J. Ross, D. A. Norrgran, J. A. Wernham, J. N. Orlich

INTRODUCTION Laboratory testing for magnetic concentration circuit design is a requirement, just as it is for most other types of concentration. Natural variations in raw materials allow on1 y the broadest of generalities to be made regarding magnetic separation. Further, magnetic fields are geometry dependent, leaving fundamental models of a separator overly dependent upon the exact conditions for which the models were derived. Despite this, an understanding of the basics of magnetic separation and of the problem to be attacked can result in rapid progress towards the final circuit design with a relatively simple testing program. Magnetic Separation Basic Principles A magnetic field can readily be understood in terms of lines of flux. A familiar demonstration of these lines of flux is the pattern of iron filings on a sheet of paper when a magnet is placed underneath. Lines of flux2 are measured in Gauss (1 line/cm2) or Tesla (10000 gauss). Regions of high field strength have a greater number of lines. Field direction is indicated by a convergence of lines. When a particle is placed in a magnetic field it cuts the lines of flux and alters them in one of three basic patterns. These patterns are referred to as diamagnetic, paramagnetic and ferromagnetic. Diamagnetic materials have electronic structures which react to oppose an applied magnetic field. This opposition acts to locally reduce the applied field slightly. The visualization is that lines of flux diverge and go around the particle. Because of this divergence or opposition, a diamagnetic particle will tend to move towards regions of lower flux density. That is to say that the particle will be repelled by a magnetic field. Aluminum oxide and napthalene are examples of diamagnetic materials. Paramagnetic materials have an electronic structure which increases an applied magnetic field. Although these materials also exhibit diamagnetism, they have randomly oriented impaired electrons which align with the magnetic field. The resultant local field enhancement is significantly larger than the diamagnetic opposition. The visual-

Jan 1, 1986

By Scott Stebbins

Cost estimating and economic evaluation software provide evaluators with the ability to predict the profit potentials associated with mine design alternatives even during project exploration and prefeasibility. Examining a multitude of development alternatives early on serves to identify aspects critical to profitability and to increase the reliability of economic projections. A case history illustrates how Sherpa Cost Estimating Software, when used in conjunction with Apex Software for Economic Evaluation, significantly enhances an evaluator's ability to examine design alternatives in a timely and reliable manner. The costs and economic impacts associated with various access routes, production rates, equipment mixes, and stoping methods are projected.

Jan 1, 2002

By A. B. Holland-Batt

Following a relatively static period in the 1960s and 1970s when incremental development rather than innovation was the norm for gravity separation, the last 15 years has seen a number of new developments in this area. The paper briefly reviews the traditional gravity separation techniques and then examines the newer developments such as centrifugal separators. Particular emphasis has been placed on novel devices or improvements that offer either better control or improved performance.

Jan 1, 1998

By M. Menegaki

Restoration of abandoned mine sites is still one of the weak points of mining practice. The latter stands especially for the case of the surface coal and lignite exploitations, where the extended size of the disturbed land and the drastic changes to the geomorphologic features do not facilitate the implementation of a cost effective and environmentally sound reclamation plan. The paper examines the parameters involved towards the legal requirements for the reclamation of the first lignite exploitation in Greece, namely the ?Plakes? mine, located at Euboea, due to the particularities of the site. Then an integrated redesign procedure is presented, aiming at minimizing aesthetic degradation, confronting technical difficulties and preparing the site to accept new uses.

Jan 1, 2005

By F. Michael Jenkins, Elaine T. Bowers

Longwall systems are used to mine approximately 50 pct of the world's total coal production. Single entries are the predominate method of longwall development in Europe and Asia where mining conditions are much more severe than those encountered in the United States. During the 1970's and early 19801s, the Bureau of Mines and the coal mining industry invested nearly $20 million in single entry and related research. This report reviews the accomplishments of single-entry research in the United States. Two U.S. single-entry field projects are described; the Sunnyside Single-Entry Project conducted in central Utah, and the Tunnel Boring project conducted in northern West Virginia. Two other important studies are discussed, the Single-Entry Study by NAMCO and the Single-Entry Design Study by Ketron. Inc. This review compares the resulting technology with European counterparts to further assess the utility and efficiency of the U.S. systems, and final1 y, it discusses future research and development options which would lead to safe and productive single-entry longwall development in this country.

Jan 1, 1986

By Samara Ali-Ahmad, Keith Hanks, Cindy Pham

The City of Los Angeles will rehabilitate approximately 9 miles of its North Outfall Sewer. This sewer was constructed in the 1920s as an unreinforced concrete semi-elliptical sewer. One of the methods for rehabilitation is to approach the sewer as a pre-excavated tunnel and install pre-cast segmental liners to provide a single pass corrosion resistant, structurally self sufficient project. The estimated cost for this project is $46 million. The project has completed the pre-design study, and the design is now underway.

Jan 1, 2003

By G. T. Adel, P. E. Richardson, R. Pazhianur

Cathodic protection using impressed current was employed to reduce mill wall wear during ball milling. Wear rates were determined from weight-loss measurements made on four 1-in.-diam mild steel coupons that were installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH levels of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 30% to 60%. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It was also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1998

By S. A. Voltura

The Phelps Dodge Miami smelter has smelted copper concentrate using the ISASMELT technology since 1992. The design throughput rate was 591,000 tonnes/year and after a slow start-up, the production rate has exceeded the design after the seventh year of operation. In 2002, the smelter consumed 719,000 tonnes of copper concentrate and has the potential to hit the permitted rate of 772,000 tonnes/year. Improvements to the smelting vessel and the surrounding support processes have allowed for continuous improvement from start up until now. This presentation will outline the chronological events and the improvements completed to accomplish these improvements

Jan 1, 2004

By Kal V. S. Sastry

Mathematical and expert system models are being used extensively for mineral process engineering. There exist no standardized methodologies for their computer implementation. In meeting this need, this paper introduces the concept of a process software model, or simply a software model and presents a two-step methodology for its development involving software model specification and development. The software model specification is to be performed after extensive discussions with the ultimate users of process software based on which the software model is developed. These software models provide a formal basis for the design and construction of software objects corresponding to the real world process objects.

Jan 1, 1994

By E. Westman

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999

Planning the primary development of a mineral deposit usually is done only once during the life of a mine. As a consequence, not optimizing the primary development of a mineral deposit can cause disadvantages over the whole life of a mine and can lead to higher costs. As a contribution to an improved primary development design procedure beyond the already existing work a study of the identification and quantification of the influence of parameters on primary development based on operational data from working mining operations has been completed. Based upon such a quantification of the influence of parameters a sequenced decision model was developed, that enables to develop an initial concept for the design of the accesses from the surface based upon a few critical parameters. Such a model will not replace detailed planning work within a feasibility study, but it is intended to reduce the amount of planning efforts at an early project stage through providing information what are most likely economic solutions, based on simple rules.

Jan 1, 1997

By Bern Klein, Richard W. Lawrence, Scott Frostad

Laboratory and field scale kinetic testing was conducted to evaluate scaling up of laboratory data. Two 20- tonne (field) cells were monitored for internal temperature, pH, conductivity, volume and rate of flow, and water quality. On a surface are. basis, results showed sulfide oxidation rates obtained using 50-kg cells are more sensitive to changes in aeration than those from 1-kg cells. Correcting the laboratory oxidation rates for field temperatures with a pH 7 activation energy, which is in the field drainage pH range, returned oxidation rates an order of magnitude lower than the field cell rates.

Jan 1, 2000

By C. Patrick

Longwall face-to-face equipment transfers or moves are, for many companies, the largest single source of non-productive time in a longwall mining system. Detailed planning and resourceful thinking are paramount for economical, safe, and timely longwall moves. New equipment and innovative techniques are frequently tested in order to reduce overall move time. Determining the cost effectiveness of these ideas is difficult since the decision is influenced by many subjective factors. A project scheduling simulation model of the longwall move process was developed in order to analyze and assess the economic viability of innovative transfer methods and equipment. The model provides a project duration frequency distribution and lists of critically indexed activities and paths. It compares the monetary savings from reduced transfer time and capital costs for several innovative ideas.

Jan 1, 1994

By E. I. Jurgens, K. E. Hanney, D. C. Comrie, R. H. Fletcher

Introduction The reclamation of mine/mill tailings areas is undertaken for a variety of objectives including safety, appearance, economical use of lands and forests and long term storage of a future resource. The establishing of criteria for these objectives at any site is a shared task of the government and mining company. Our attention in this paper is directed to uranium mine/ mill tailings as they are handled in the Canadian industry and in the unique Canadian climate. We focus our attention on the state of the art. Uranium is a ubiquitous mineral forming an average of 4 g per tonne of the Earth's crust. Ores are mined at about 500 g per tonne so that the residual content of uranium in tailings is comparable to average background levels. However, as in most mine/mill operations, the ore contains other minerals that become readily mobile after milling operations. Thus the main objective of tailings impoundment is the stability both physically and chemically of the mobile materials. Since the requirements for the operation and construction of tailings areas in Canada have changed considerably over the past decade, there exists a great many mine/mill tailings areas which while considered adequate in their day, would not meet modern criteria. However, most of these installations pose no concern or hazard to the public. The proximity of mine/mill development to inhabited land areas has necessitated more stringent modes of tailings operations and provisions for tailings site reclamation. The more important of these have been: 1) the prevention of dyke failure, with large liquid-solid outflows onto adjoining lands, and 2) the prevention of seepage from the tails of pollutants such as chlorides, sulphides, heavy metals and radionuclides. Uranium mill tailings are discharged as a slurry from the concentrator after the removal of generally only about 1000 g, or less, per tonne of uranium from the as-mined ore. As a consequence, a great volume of low level activity waste is generated. The amount of tailings is expected to grow in quantity in the future even faster than the increase in yellowcake production, as the demand for energy

Jan 1, 1980

By H. Tutu

The legacy of gold mining operations continues to affect water quality in the Witwatersrand Basin in South Africa. The acid mine drainage (AMD) emanating from the tailings dumps liberates heavy metals from the ore minerals. The objective of this study was to characterise the geochemical processes that are important in understanding chemical evolution of polluted water in the study area. Analytical results for water samples collected in the catchment of the study area generally showed elevated concentrations of heavy metals in the vicinity of tailings dumps and mining operations and a decrease in the distal. Dams and wetlands, despite their proximity to the tailings dumps, recorded low concentrations of heavy metals and other pollutants. The characterisation of AMD was summarised in a conceptual model in which plots of redox potential versus pH and electrical conductivity versus pH were identified as the most important sub-models that captured the gross physical-chemical characteristics of polluted water and its interaction with the environment.

Jan 1, 2006

By M. R. Grundy

The Robinson project is based on the porphyry copper and gold deposits in the Robinson Mining District, near Ely in Eastern Nevada. The district was mined from the late nineteenth century to 1978 by Kennecott Copper Corporation and its predecessors. Operations ceased when falling copper prices in the late 1970's made their outdated mill and smelter complex at McGill uneconomical. In October 1991, Magma Copper Company (Magma) acquired the many claims that cover the known porphyry copper deposits in the district These occupy a disturbed area about nine miles long and three miles wide between the towns of Ely and Ruth. Magma proposes to build a copper / gold mine and concentrator and expand the existing gold leaching facilities. Several pits, previously mined by Kennecott Copper Corporation, will be enlarged; the use of larger, more modem equipment will result in higher productivity and lower operating costs in general. ICF Kaiser Engineers, of Oakland, California, were awarded the con-tract for detailed design of the process facilities, which was essentially complete by the end of 1993. The project at present is awaiting completion of the environmental permitting process; state air and water permits are in hand, and the Bureau of Land Management's (BLM) current schedule indicates that the final obstacles to construction will be cleared by early fall of this year.

Jan 1, 1994

By Carl E. Nelson

Shallow epithermal stockworks hosted by maar eruption craters contain over ninety percent of the bulk mineable gold identified to date in the Circum-Caribbean region. Pueblo Viejo (Dominican Republic) and Santa Rosa (Panama) contain combined gold reserves of over 600 tonnes. Bulk mineable gold deposits are also being discovered in and around veins that were formerly mined underground. Bellavista, El Recio and San Martin (Costa Rica) contain combined announced gold reserves of over 50 tonnes. Representative rock suites collected at 8 bulk mineable gold deposits include 291 samples of veins and vein stockworks, hydrothermal eruption breccias, sinter, variably altered host, unaltered host, nearby intrusive rocks and basement. Analyses completed to date show that Circum-Caribbean epithermal ores are enriched in arsenic, mercury and antimony as well as gold and silver. Exploration efforts in the region naturally focus on districts with past production. However, an order of magnitude more bulk mineable gold has been discovered in shallow epithermal stockworks outside of the old bonanza vein camps. Exploration guides include basal island arc volcanic sequences, hydrothermal and hydrovolcanic (maar) eruption breccias, thinly-bedded carbonaceous maar sediments, and hot spring-related silicification and argillic alteration.

Jan 1, 1990

By T. L. Heisler

The Cigar Lake project, located in northern Saskatchewan (Figure 1), is one of the world?s largest high grade uranium deposits, with reserves of 150 million kilograms of uranium in a deposit averaging 430 metres below the surface. The Cigar Lake project is being developed by Cigar Lake Mining Corporation (CLMC) which is owned by Cameco Corporation (48.75%), Cogema Canada (36.375%). Idemitsu Uranium Exploration Canada Ltd. (12.875%) and Korea Electric Power (2%). Mining the Cigar Lake orebody is presenting a very real challenge due to the high grade and the ground conditions in and around the orebody. Presently, an underground test of various mining methods is underway.

Jan 1, 1992

By H. M. Breza

Utilization of Bucket Wheel Excavators and Overland Conveyor Systems to remove overburden provides increased productivity and flexibility to a surface mining operation. The utilization of such a system at the Texasgulf Inc. Aurora, North Carolina Mine has significantly improved the overall productivity of the mining operation. System flexibility is evidenced by adaptation to operation requirements such as mining area moves, movement of excavated overburden to designated sites, selective handling of overburden, spoil placement contouring, and providing an environmentally sound and safe operation. System productivity is evidenced by actual case studies relating to overall production, excavation rates, and cost effectiveness.

Jan 1, 1993

By John A. Herbst, K. Rajamani

Process improvement is probably the most widespread objective of mineral process plant operators in the late 1980's. An important part of such improvements is dynamic optimization which involves reacting to inevitable plant disturbances in such a way that productivity is maximized at every instant of time. This paper describes the way in which mathematical models can be and have been used in dynamic optimization. Both off-line and on-line model applications are described.

Jan 1, 1989