Search Documents

By R. Asmatulu

According to Darcy's law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By S. K. Sharma

The Bureau of Mines' rapid method of dewatering fine-particulate slurries uses extremely high molecular weight polymers. These polymers form large, strong flocs which can be dewatered by sieving or sedimentation. However, sometimes these flocs deteriorate rapidly if water is not removed immediately. During field tests, clay slurries have been encountered that could have been dewatered economically if it were not for the rapid floc deterioration. A kinetics study was conducted to determine the rate of kaolin-PED floc degradation in which polymer addition, to bring the flocs back to their original condition, was used to determine the extent of floc decay. Results showed that the amount of polymer added, to replace polymer lost by spreading, was less for the lower PEO concentrations. For this clay-polymer system, floc breakage as judged by polymer additions followed first order kinetics. It was also found that the addition of fluoride ion stabilized the kaolin flocs.

Jan 1, 1992

By R. L. Grayson

A goal programming-based worker scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model the accomplishment of each regular and non-regular job is a goal. The objective is minimization of the deviations away from the goals. A number of coefficients are used as premultipliers of the decision variables in order to address practical considerations associated with the utilization of workers and the requirements of jobs. Some of these premultipliers will be updated expertly within MMSS, timely updating the statuses of the dynamic parameters.

Jan 1, 1991

By O. M. Arafat, J. A. Finch

"The Functional Performance Equation calculated from a plant grinding survey defines two distinct ball mill circuit efficiencies and how they relate to total production rate through the target grind size. The survey data are also used to calculate a complete ball mill size distribution model, represented by the energy specific grinding rates, not just through the target grind size, but through all the size classes. Cyclone separation performance is represented by individual size recoveries to underflow. When these two unit operation performances are entered into the circuit modelling program (Streamline™), along with the circuit feed rate and size distribution, all the circuit survey size distributions and mass flows are perfectly regenerated by the program. The many issues associated with the historical Epstein (breakage-selection) models are eliminated. Once the circuit program is populated, pump and cyclone performance changes can be evaluated using a step-by-step procedure in order to maximize Classification System Efficiency. Mill water use and media sizing opportunities are also diagnosed in order to maximize Mill Grinding Efficiency at the size of interest. An example is provided. This circuit analysis and modelling system, and related training, is provided through a web-based application. INTRODUCTION Since its development (McIvor, 1988), the Functional Performance Equation for ball milling has facilitated new understanding of industrial circuit cause and effect relationships, leading to significant strides in operational performance. Success stories of this refreshing approach to plant circuit performance improvement are now too numerous to list. Finch and McIvor (circa 1986) also discovered that the Functional Performance “Mill Grinding Rate” at the size of interest was the same cumulative grinding rate that is calculated from mill feed and discharge size distributions using a first-order rate equation. By calculating these cumulative grinding rates for all screen sizes, a complete ball mill model is generated (as used by Finch and Ramirez, 1981). Others in industry, Hinde and Kalala (2009), for example, have noted the same. Lacking the complexity needed to maintain their interest, most researchers have ignored this model, broadly opting instead for Epstein’s (1948) characterization of grinding as a chemical reaction, combining “selection rate” and “breakage size distribution” functions. The much simpler ball mill model presented here has previously been incorporated into a proprietary circuit modeling program (McIvor, 2005) and used for plant improvement work (for example, see McIvor and Finch, 2007, and McIvor, 2014). Now, by combining this extremely business-friendly ball mill model with optimization criteria from Functional Performance Analysis, a circuit modeling system (including the needed supplementary steps to assure successful plant implementation of circuit design changes) is at the disposal of every plant metallurgist, grinding equipment/material provider, and circuit designer."

Jan 1, 2017

By C. K. Skokan

Various geophysical tools have been tested over the last eight years to evaluate their usefulness in defining damaged rock zones in an underground facility at the WIPP site in New Mexico. These tools include direct current and frequency domain electrical methods and seismic tomography. The electrical measurements show a "drying rind" to exist around older excavations. Seismic tomography confirms that a rind of lower velocity has developed along walls. In combining these tools, a monitoring program has been proposed to observe long-term changes in bedded salt. Results from the monitoring of electrical data over a 2-year time period illustrate the applicability of the technique in an underground environment.

Jan 1, 1993

Optimal gold recoveries largely depend on efficient liberation of the gold or gold-bearing minerals as well as on maximum access for the lixiviant. Thus, crushing and grinding may become the most costly part of gold ore processing. It may, in fact, represent 50% to 70% of a plant's operating costs (Michaelis, 1989). The increasing significance of refractory gold will require even more cost-efficient comminution of ultrafine sulfides and/or native gold. Transitional ore zones with semi refractory gold may respond to direct leaching if better particle fracturing is being achieved (Baum, 1991, 1993a). Many oxide ores have been left in the ground because they were unsuitable for heap leaching since conventional comminution could not facilitate economic gold extraction. Also, the costs of conventional bal1 mill operations did not permit the recovery of gold from many ultrafine, low-grade refractory ores. As shown by Marsden et al. (1993), the trend to treat ores with progressively lower grades will involve power-and leach-efficient grinding applications. Our current laboratory work shows that high-pressure grinding roll (HPGR) Polycom grinding may enable many mining companies to add large amounts of these "non-leachable" ores to their current heap or mill leach feeds. This finding may dramatically change the economics of many oxide gold ore operations and may add significant reserves to ores amenable to direct cyanidation.

Jan 1, 1994

By Yubo Tu, Lianqi Wei, Tianyi Zhao, Peiwei Han, Zhengchen Li, Shufeng Ye

The effect of oxygen partial pressure on the volatilization percentages of valuable metals from iron-rich pyrite cinder by chlorination-volatilization method using CaCl2 as chlorinating agent was investigated in this study. The volatile products were collected directly and analyzed by X-ray diffraction. It was found that there were CuCl2, CuCl, PbCl2, and ZnCl2 existed in the volatile products. Au and Pb volatilization percentages were almost not affected by oxygen partial pressure. Both Cu and Zn volatilization percentages were negatively correlated with oxygen partial pressure when CaCl2 dosage was no more than 4 wt%, and almost uncorrelated with oxygen partial pressure with a CaCl2 dosage of 6 wt%.

Dec 19, 2023

By G. B. Amicucci

A Denver Autometrics Particle Size Monitor, PSM-400, was installed at Golden Sunlight Mines, Inc. in October 1988. The PSM-400 measures the grind product's particle size and percent solids. The particle size is used to control grind size by automatically adjusting mill feed rate. The PSM's continuous response to ore changes has improved grind product uniformity and mill throughput. Metallurgical testing has shown the PSM's accuracy to be +/-1 % + 150 µm (100 mesh).

Jan 1, 1991

By T. V. Ramey

Heap leaching in certain parts of the world, such as Chile's Atacama Desert, brings unique design problems in the form of possible large differential settlements of the foundation soils due to the dissolution of salts in northern Chile the soils often contain very high concentrations of soluble salts (nitrates, potassium, magnesium, and common sodium). When a leak in the liner occurs, the escaping solution dissolves these salts and triggers differential settlement. If the settlement is great enough, the geo-membrane tears, the leakage increases, triggering more differential settlement. The nitrate plants have experienced many occurrences of this phenomenon where a brine pond will undergo a sudden and complete loss of the impounded liquors. The authors present a simplified technique to quantify the differential settlement resulting from dissolution and provide a method which can be used to select a geo-membrane with suitable flexibility under axi-symmetric (multi-axial) load conditions to tolerate the predicted settlement. (This paper was previously published for Randol Gold Forum 1996 [Ref. 6]).

Jan 1, 1997

By Thomas E. Newman

This paper is a case study using new laser-terrain-mapping technology by EagleScan, Inc., for creating topographic maps. Holnam, Inc., has used this technology to create maps and volumetric calculations of several mines in the United States. The information is superior to conventional methods through accuracy, manpower, time, and cost. Holnam, Inc., was the first cement manufacturer to use the Digital Airborne Topographic Imaging System (DATIS?). The technology uses the DATIS? to produce high-resolution terrain maps and volumetric assessments of any area. DATIS? is a mapping instrument that integrates (1) a Light Detection and Ranging (LIDAR) instrument to measure terrain elevation using laser light, (2) a large-format digital camera, (3) a relative position Global Positioning System (GPS) to measure aircraft position, and (4) an Inertial Measurement Unit (IMU) to measure aircraft attitude. The DATIS? can measure up to 220,000 elevation samples per mil. The system continually collects data on the aircraft's position and measures the time for each laser pulse transmission to return from the ground, giving each sample a GPS reference. The system can operate at night, in overcast sky, and during high-wind conditions and can measure terrain below vegetation cover, unlike standard aerial photography used for traditional surveying and mapping. Surveyed ground-control panels are no longer necessary with this new technology, and only one ground GPS base station located within 60 mi from the aircraft position is required. A computer elevation-point data file is created with the x, y, z coordinates of each laser elevation sample. With this file, CAD engineering programs can create topographic maps that rival products using conventional aerial mapping techniques. Volumetric measurements of stockpiles and pits are also available due to the high density of points collected from an area. This new technology radically changes the turnaround time for map users, giving a product in the format used by today's cartographers. The time line from flight to maps is measured in days instead of weeks.

Jan 1, 1999

By F. E. Kottlowski

Widespread high-calcium limestones in New Mexico region are low -in magnesium, but some units include shale interbeds deleterious for sulfur removal usage. Thick limestones in Mississippian Escabrosa, Lake Valley, and Leadville, Pennsylvanian Madera and Hermosa, Pennsylvanian-Permian Horquilla, Permian Hueco and Capitan, Cretaceous U-Bar, and some Cenozoic travertines are high-calcium units. Significant outcrops are in mountains of southwestern, south-central, central, southeastern and north-central New Mexico, southeastern Arizona, southwestern Colorado, and northwestern Chihuahua. Coal-fired powerplants are mainly in northwestern New Mexico and eastern Arizona, thus transport is mainly by railroad.

Jan 1, 1994

By J. W. Oberholzer

This paper describes research being undertaken by the Chamber of Mines Research Organization (COMRO) which is designed to assist the continuous miner operator and section foreman in the performance of their jobs. The project will initially provide visual assistance to the miner operator, and later will semi-automate the mining (cutting) process. Using a technique known as "RF tagging," the project will also provide real-time or near-real-time information about the performance of the loading and hauling units to the section foreman, allowing him to quickly detect problems and take action where appropriate. The project is based upon the application of currently available technology, and the first phase is scheduled for in-mine testing within the next year.

Jan 1, 1991

By J. LeRoy Peterson

This paper presents some of the theoretical aspects as well as some results of actual plant operation of the Ty-Hukki Classifier. Dual classification steps within a unit vessel are achieved by controlled separation of the sand product under turbulant flow conditions, followed by further classification under strictly laminar flow conditions. Plant operation has shown some of the benefits of the superior sharpness of classification to be reduction of circulating load in grinding circuits, prevention of overgrinding, increase in mill feed rate and consequent reduction in cost per ton of ore.

Jan 1, 1966

By R. J. Lutton

The U. S. Army Corps of Engineers is seeking empirical slope data from mining companies and other organizations to help establish guides for engineering Judgment in crater excavation for canals and other civil works. Slopes from about 100 open pits and other excavations range in heights to greater than 1000 ft. Factors known or expected to affect stability (and optimum slope inclination) are: geological structural orientation, geological structural ordering, method and technique of blasting, design life of slope, groundwater conditions, depth of excavation, climate, and height. These and other more subtle factors appear to combine and produce an overall effect brought out best on a family of empirical curves relating slope height and inclination.

Jan 1, 1968

By Allegra Yeley, Ted Klemetti, Gamal Rashed, Tim Miller, Nicole Evanek

In 2015, the Subtropolis Mine in Petersburg, OH, experienced a massive ground collapse that continues to grow over time. Horizontal stress effects have affected the roof at this operation in the past and may have played a large role in this collapse. Horizontal stress can impact the roof and floor stability and endanger the health and safety of underground stone miners. Mines experiencing damaging effects from horizontal stress typically find that the principal stress direction is the same throughout the mine and the region. At the Subtropolis Mine the principal horizontal stress direction appears to change as conditions change and differs from the regional horizontal stress, particularly near the collapse or other roof fall areas. The growth over time of this collapse and other roof falls have been captured and analyzed using geologic mapping, 3D LiDAR scanning, numerical modeling and geographic information systems like ArcGIS. Utilizing these tools to better understand sitespecific conditions can be critical to reducing the potential of massive ground collapses in the underground limestone industry.

Feb 1, 2024

By Michael L. Cramer, Kunsoo Kim

INTRODUCTION The Columbia River Basalt beneath the Hanford Site is one of several rock types being considered by the U.S. Department of Energy for the first commercial high-level nuclear waste repository. The Basalt Waste Isolation Project (BWIP) has been carrying out a comprehensive investigation to assess the feasibility of constructing a repository in basalt and to develop technology required for repository engineering and site characterization. Development of a nuclear waste repository requires a number of design considerations not usually necessary in the planning of conventional underground structures. Principal among these is the thermally induced stress field resulting from waste emplacement. This thermal stress, super- imposed on the preexisting in situ- and excavation- induced stress fields, needs to be evaluated in the design process due to the sensitivity of waste emplacement density to this factor. The nature of this thermally induced stress field is dependent on several factors, including the temperature distribution around the repository openings, the thermal properties of the rock mass, and the deformability of the rock mass. Re1iable performance of the repository structure is largely determined by the ability to under- stand the above rock mass characteristics and predict the underground opening response to waste emplacement based on this understanding. To gain an understanding of this rock mass behavior in a repository condition, the BWIP has conducted a large-scale heated block test in basalt at the Near-Surf ace Test Facility (NSTF) on the Hanford Site. This paper presents the results from the elevated temperature phase of the block test in which the thermal, mechanical, and thermo- mechanical response of the closely jointed basalt rock mass was evaluated as a function of stress and loading orientation at varying temperatures up to 200 oC. SITE GEOLOGY The NSTF test areas, including the block test site, are located in the entablature zone of the Pomona basalt f low. The Pomona flow entablature is structurally typical of most flows in the Columbia River Basalt Group in that it is characterized by long, undulating, polygonal columns up to 2.4 m in length. Columns vary from 15 to 30 cm in diameter, averaging about 20 cm. Over their length, columns can vary in dip by 150 to 200. The column structures are dissected by subhorizontal cross joints that are generally discontinuous and seldom cross columnar joint boundaries. Spacing of the cross joints also averages about 20 cm. A representative joint pattern taken from mapping of the tunnel wall near the block test site is shown in figure 1. Application of the Rock Mass Rating System (Bieniawski, l979) to the block test site yielded an overall value of 62. The corresponding value from application of the Q-system (Barton et al., 1974) is 8.7 (Cramer and Kim,1985). The NSTF is approximately 50 m below the surf ace. However, this depth is sti1l above the water table and conditions are generally dry. Interstitial water exists as the result of percolation of meteoric water from the surface.

Jan 1, 1986

By Prasad S. Mulukutla

INTRODUCTION The use of specialty chemicals In mining Is an Important consideration In determining the economic efficiency of a floatation plant. The plant metallurgist would like to maximize the recovery of valuable minerals while maintaining an acceptable grade product. The direct cost of the reagents, while significant, Is only a part of their economic effect. Reagents determine the flotation rates and the selectivity of the mineral separation. In flotation practice, mineral selectivity can be achieved through the addition of various reagents that can control the wettablllty of a particular mineral In the flotation pulp. The reagents which will generally optimize the flotation process are commonly classified Into three distinctive categories: collectors frothers and modifiers. Large tonnages of metal sulphide concentrates which are the source of most of the common base metals are produced economically by fairly standard flotation techniques. The advent of modern technology coupled with the necessity of processing finely disseminated and complex ores of low grade has Increased the need for utilization of non traditional and high selective chemicals reagents for the economic recovery of metals and raw materials. Mining operations in developing countries continue to progress at a rapid growth as many countries mine and process both metallic and nonmetallic ores. The total mine production of base metals, precious metals, Iron ores and coal In developing countries In Africa, Asia and South America has been much higher as compared to the western world production In terms of tonnage and dollar value. Global capital Investments In mining during 1991-95 Is $ 55.1 billion and It Is anticipated that the development of new and specialty reagents may be concentrated In the processing of aluminum , copper, precious metals and Industrial minerals with special reference to potash, phosphates, kaolin and silica sands.(1) The challenge for the design and development of new specialty chemicals Is dependent on Its cost performance and environmental acceptability. Information on the theory and application on the development of mining chemicals has been reviewed In several conference proceedlngs,(2-4) publications(5) and also discussed by several Individual authors.(1,6-10) These publications serve as a comprehensive reference source on the reagents used In several flotation processes. This paper discusses the present trend in the use of specialty mining chemicals In diversified mining operations on several mineral systems with particular reference to sulfide ore systems. The necessity to expose these specialty chemicals through aggressive marketing techniques In mining operations In many developing countries Is also presented. SPECIALTY CHEMICALS Specialty mining chemicals, like other specialty chemicals, share common business characteristics that transcend geographic boundaries. They are manufactured 1n a few selected areas, generally expensive relative to commodity chemicals, shipped and compete globally and usually require specialized knowledge for proper use. Specialty mining chemicals are relative newcomers to chemical markets. The vast majority of mining chemicals are derived from products that are less than two decades old. Traditional collectors and frothers have been available for a considerably longer time. The emphasis on adding value to existing products and byproducts Is responsible for several characteristic features of the mining chemicals business. Most raw materials for these chemicals are related to oil and gas byproducts, chemical refineries, pulp and paper mills and all chemical manufacturers. Until the last several years these operations were located In Industrialized countries, while a significant number of mining chemical users were In developing countries. Therefore International trade In mining chemicals developed through agencies or agents in each particular country.

Jan 1, 1993

By C. W. Matthews

Introduction Screening is an art, one of the oldest in the process field today, and one of the most widely used in our present age. Screening is being applied to an ever-increasing number of assignments, in an ever-expanding circle of industries. Screening is defined precisely as a mechanical process which accomplishes a separation of particles on the basis of size and their acceptance or rejection by a screening surface. Particles are presented to apertures in a screening surface and rejected if larger than the opening, or accepted and passed through if smaller. Screens are machines with screening surfaces used to classify materials by size. The screening surface is the medium containing the apertures for the passage of the undersize material. Screens are put to many uses - size separation, dewatering, desliming, media recovery, scalping, trash removal, washing, dedusting, conveying, concentration, and many combinations of these functions. It is interesting to note that screens are used for handling commodities

Jan 1, 1985

By John P. Norton

Microcystaline silica has been mined in Illinois from the Clear Creek formation since the turn of the century, especially in the area around Tamms in Alexander County, in the southernmost part of the state. Production of this silica, consumed mainly by the abrasives and coatings industries but also sought after for many filler/extender uses, has grown with the economy with several new applications overshadowing traditional markets in recent years. Such an important commodity was given the early attention of the Illinois State Geological Survey and a very complete report was issued in 1953 (Report of Investigations No. 166), authored by J. E. Lamar. The mining and processing of the silica ore has changed very little since the first reported production in 1906, although emphasis has been placed on the production of the finer sized grades to meet newer market requirements. Industrial Mineral Notes 40, published by the Illinois State Geological Survey in June 1970, describes a method by which a less than 1-micron fraction could be commercially produced from the readily available finest commercial grade presently being marketed (99% minus 10 microns). The finer grades exhibit to a lesser degree the reinforcement, high flatting efficiency, thickening and dry brightness properties associated with the synthetically produced silicas. It is expected that the extremely fine grades of microcrystaline silica will become accepted in the markets that now use a combination of precipitated silica and less expensive extender/filler minerals such as kaolin or calcium carbonate.

Jan 1, 1976

By G. S. Adisoma, J. J. K. Daemen, R. O. Roko

A common assumption in determining the shear strength of a rock joint using a direct shear test is that the surfaces undergoing relative shear are in complete contact. Furthermore, the limiting displacement associated with the residual strength values is obtained based on engineering judgement through visual inspection of shear force versus displacement curves. This study proposes a systematic way of determining the residual shear strength of rock joints by evaluating the limiting displacement leading to a minimum cohesive strength value and taking the true area of contact into account. The results of the study indicate that there is a limiting displacement associated with the residual shear strength, and some rocks may have an inherent interface residual cohesive strength different from zero. When the cohesion is different from zero, the residual shear strength is likely to be underestimated if the true area of contact is not considered. In the case where zero calculated cohesion is obtained, the area of contact has no bearing on the shear strength equation because the frictional force depends only on the normal load.

Jan 1, 1986