Search Documents

By Geoffrey Purcell

The flotation response to amine collector of quartz and the feldspars microcline and albite, of the pyroxenes augite and spodumene, and of olivine can be, explained by a physical adsorption model. Flotation decreases in the order given above, and the different behavior of the three groups is attributed to structural variations of the silicates, With sulfonate collector both chemical action and physical adsorption play their part in producing hydrophobic surfaces, and flotation increases in the order given.

Jan 1, 1966

By Jamal Rostami

Continuous miners (CM) are the most popular underground mining machinery in soft rock mining, playing a dominant role in the production of minerals ranging from coal to evaporites while finding increasing use in salt and potash mines. Along with the ongoing technological advancements in the mining industry and the underground equipment, new generation of CMs offer several new features that are designed to enhance their operational capabilities and production rate. In addition to new bits and bit holders, one of the areas of improvement is the cutterhead design through computer modeling and simulation based on the full scale cutting tests. This paper discusses the state-of the-art CM technology and development of the computer models for design analysis and performance estimation of CMs. The general approach used in the modeling, along with the results of field trials for several projects will be presented.

Jan 1, 1998

By Christopher Laughton, Michael P. Bruen

At Fermilab, a 4000-ft long underground complex has recently been constructed for a high-energy physics experiment. The complex is sited up to 350 ft, below grade principally in bedrock. The rock excavations were mined by TBM and drill and blast methods and supported by a combination of rock bolts, dowels and shotcrete. Water control was achieved using a combination of pre- and post-excavation grouting, drainage systems, drip shielding and air desiccation measures.

Jan 1, 2003

By Richard L. Coleman

El trabajo de ensayo metalúrgico para desarrollar un flujograma es el que ahora describimos, comenzando con una información experimentada requerida en todo momento hasta llegar a un esquema final de flujo de un proceso. Tanto las pruebas de laboratorio como de planta piloto son revisadas adecuadamente sobre las experiencias anteriores.

Jan 1, 1982

Unless otherwise indicated, pounds are US avoirdupois, feet are US, and gallons are US.

Jan 1, 1985

By Thomas A. Gray

The Dolph Mine fire site is located in Lackawanna County, PA, approximately three miles northeast of the city of Scranton. The fire was burning in both coal refuse (culm) and underground anthracite mine workings. It was reportedly begun by rubbish burning on top of a culm bank. A site investigation was completed in 2006 to define the extent of the fire and to recommend fire control measures. A cut off trench was selected as the principal control method. Plans and specifications were prepared in late 2006. The project was bid and a contractor selected in early 2007. The trench construction was completed in 2007. This paper describes the investigation and selection of the fire control method and discusses the trench construction.

Jan 1, 2009

By Q. Xu

Adsorption of nonionic/anionic surfactant mixtures on kaolinite has been studied with sodium dodecylsulfate as the anionic surfactant and octaethyleneglycol mono-n-dodecylether as the nonionic surfactant. Synergistic interaction between these surfactant was found to cause adsorption of the nonionic surfactant with its hydrophilic chains protruding into the bulk, leading to substantial changes in wettability and dispersion characteristics of kaolinite. Similarly, hydrophobicity changes are observed also for silica particles upon adsorption of nonionic ethoxylated alcohols owing to possible changes in the orientation of the adsorbed surfactant molecules at the interface.

Jan 1, 1991

By Bruce L. Bryson

In the past decade a principal growth area in refractory technology has been the development and use of extra high alumina refractories. The refractories user is asking for, and is prepared to pay for, higher purity, more dense materials with longer life, less maintenance, and better dimensional tolerance to meet the exacting demand of high output processes. High alumina and bauxite refractories are being used more and more to keep pace with the demand for guaranteed performance. The steel industry, for example, is starting to place great reliance on these products. A unique material now available with all the requirements for extreme purity and density is tabular alumina, already proving itself in many refractory applications.

Jan 1, 1973

By M. S. Klima

Proper analysis of washability data can lead to the development of a maximum yield coal preparation plant flow sheet. Simulations, as simple as spreadsheet mass and water balancing, are important in examining yield maximization and middlings liberation. Key to such attribute tracking flow sheet simulations is the distribution model, expressing the probability of a species reporting to the product stream. There are many such models in the literature. This paper examines a functional form that can represent or fit most of the proposed distribution functions.

Jan 1, 1997

By A. A. Campoli

The U. S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

By Y. S. Roditis

A new method for interpolating a block model is proposed, where both the diamond drill holes (DHs) and blast holes (BHs) data are used. Combining these data types poses a geostatistical "class size" problem due to the different statistical properties of the densely populated BHs and the sparsely populated DH data. This paper discusses how linear regression was used to adjust the DH values prior to the interpolation to account for the "class size" problem which is inherent to the procedure. The correlation between the BHs and the DHs is found. The DHs are then corrected based on the regression line. Each block that falls within a certain range of influence of a blast hole is assigned a different code and is interpolated with the combined BH and regressed DH data set. Blocks that fall outside the range of blast hole influence are interpolated using the original DH data set. A comparison against other methods, indicate a 12% improvement over using DHs only and a 2% improvement over using BHs only.

Jan 1, 1992

By P. C. Kapur

The kinetics of green pelletization in a laboratory balling drum have been studied, using pulverized limestone as a model system. The growth characteristics of green pellets were found to be extremely sensitive to the moisture content of the material. Empirical kinetic equations, which incorporate a function of specific surface of the pellets as the criterion for growth potential, have been found to describe growth in a nucleation region and in a ball growth region. The rate constants in the kinetic equations are strongly dependent on the moisture content of the material being pelletized. Size distributions of the halls at different stages of pelletizing are also discussed.

Jan 1, 1965

By J. G. Groppo

The Andritz Ruthner Inc. hyperbaric filter was evaluated at a pilot scale for dewatering fine coal cleaned by froth flotation. The pilot scale dewatering testing was conducted at a solid feed rate ranging from 100 lbs to 200 lbs/hr-ft2. Effect of hyperbaric operating parameters and addition of various surfactants and flocculants were evaluated on dewatering of fine coal. The tests data indicated that for the minus 100 mesh and minus 28 mesh clean coal product, the Andritz hyperbaric unit provided filter cake containing 23 percent and 14 percent moisture, respectively.

Jan 1, 1996

By D. W. Park

Geologic condition is one of the most important factors for longwall mining operations, especially, the existence of faults limits the mineable area, or cause stress variations at the longwall face. Recently, a longwall panel passed through a fault at the Shoal Creek Mine of Drummond Company, Inc. The fault was situated diagonally along the longwall face and the coal seam was displaced up to 2.4 m (8.0 ft) in a mode of a normal fault. LoSCoMS (Longwall Strata Control and Maintenance System) was used for monitoring shield pressure every minute and interpreting data in terms of setting, developing and final pressures. The results of the analysis regarding the influence of the fault on the shield pressure are presented.

Jan 1, 1999

By James K. Hallenburg

Geophysical borehole logging is a valuable and inexpensive tool for coal deposit evaluation, development, and production. In addition to the usual determinations of depth and seam thickness, geophysical borehole logs can effectively and accurately determine the coal ash, moisture, and heat contents in situ. Location and evaluation of the partings can be done quickly and accurately. Overburden character determination, such as roof competence, dewatering parameters, ripability, trace element content of the coal and overburden, and sulfur content can be done with existing tools and techniques. The quality of such determinations depends upon the quality of planning and calibration.

Jan 1, 1984

By E. B. Kroeger

Spoil instability has been a problem at a coal mine in interior Alaska. Parameters such as original site topography, groundwater conditions, material properties, spoil-pile geometry, geology, permafrost, natural slope instability, changing weather conditions, and dense, near-surface vegetation have interacted to produce unstable slopes. Several failure modes have been identified including deep seated earth block slides, bimodal earth flows, and solifluction. Thawing of permafrost also created conditions where sliding of spoil along the interface separating the spoil and the natural ground surface occurred when the cohesion and the friction angle of that zone was reduced to zero and below 15?respectively.

Jan 1, 1992

By F. P. Jung

This presentation will be a general overview of the Cerrejon Coal Project being developed jointly by Carbocol, an entity of the Colombian government, and Intercor, an Exxon affiliate. The word "Cerrajon", by the way, is simply Spanish for a small hill. There is a distinctive hill near the mine site, and it's the only landmark of any significance. It's shown in Figure 1. So the locals call this area "El Cerrejon", "the little hill." Let me start with some of the highlights of the project, summarized in Figure 2, and then go into more detail later. A four-year feasibility study covered the geology, quality, engineering, construction operation and marketing of coal from this region. This study led Exxon to declare the project as commercial in July of 1980. Then in September of 1980 the president of Colombia gave the government's okay to proceed.

Jan 1, 1982

By R. L. Grayson

Evidence has accumulated indicating that cultural change toward safer workplace behaviors is beginning to occur systematically in the coal industry. Through a range of programmatic mining company successes, enforcement and litigative actions, economic responses to competition, and integrated efforts by federal and state agencies, a broader participation of safety and training professionals is being achieved to address prioritized workplace problems at mines. Small steps in workplace-related improvements have been realized already, but the trends in industry safety statistics, coupled with focused programmatic initiatives, indicate that more definitive and systematic steps are occurring to improve safe behavior in the workplace routinely.

Jan 1, 1996

By Horace M. Varner

Under sponsorship of the USBM and later of the DOE, a new type of rotary rock drill has been developed by The Bendix Corporation. Originally developed for the production of holes for the installation of longer than seam height roof bolts, the flexible drill is a useful tool for many drilling applications. This drill allows hands-off or remote production of holes for increased drilling speed and greater operator safety in any strata suitable for rotary drilling. The paper discusses various applications and experience for the flexible drill system in coal mining, metal/nonmetal mining, and for general civil engineering uses. Manual, remote control, and automatic roof bolter modules are also discussed.

Jan 1, 1982

By Kevin B. Doyle

Virtually all industries use sulphur in some form. About half of the world's production is used in the production of fertilizers. Sulphur is produced in one form or another in over sixty countries in the world. The major producing countries, in order of importance, are: U.S.A., Canada, U.S.S.R., Poland, Japan, France, Mexico, and Spain. Canada is the largest exporter of sulphur presently supplying about 30% of the world elemental sulphur export trade. It has held this position since 1968. World sulphur resources are virtually unlimited. Future world competition will come from Iraq and other Middle East countries as well as Central and South America.

Jan 1, 1978