Search Documents

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains (CAC) on roof bolting machines have been proven, through laboratory and field investigations, to protect miners from respirable dust, preventing dust overexposures. Another desired application is to develop a CAC that is mounted in the compartment of a shuttle car to protect the operator from dust. The challenges faced with this design include mine ventilation rates in tandem with the shuttle car tram speeds, causing cab airspeeds that may exceed 600 fpm, as found in this study of a central Appalachian underground coal mine. Prior research and laboratory testing indicate that successfully protecting a miner in high air velocities is difficult to achieve because the clean air from the CAC is unable to penetrate through the high velocity mine air and make it to the breathing zone of the operator. During this investigation by researchers from the National Institute for Occupational Safety and Health (NIOSH), dust concentrations of the shuttle car operator were measured. Also, air velocities experienced by the operator were measured using a recording vane anemometer. Results from the survey indicate that the highest exposure to respirable dust (2.22 mg/m3) occurred when the shuttle car was loading at the continuous miner, where there was an average airspeed of 157 fpm. While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 203 fpm. This study indicates that a CAC system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, since the majority of the operator’s dust exposure occurs in air velocities less than 200 fpm. INTRODUCTION NIOSH has issued a contract (#200-2015-63485) with Marshall University and J.H. Fletcher & Co. (Salem et al., 2016) to develop a canopy air curtain (CAC) for coal mine shuttle cars. The proposed design maintains a similar design to the roof bolter CAC by providing filtered air via a blower over the operator. The plenum, which will provide the uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a CAC is ventilation airflow perpendicular to the plenum airflow [Engel et al. 1987]. This ventilation airflow, if the velocity is significantly high, can shear the downward flow from the plenum. The shear caused by the ventilating airflow can reduce the effectiveness of the CAC by either disrupting the downward flow or allowing contaminated mine air into the CAC zone of protection."

Jan 1, 2018

By Andy B. Wallace

Veins in the Pyramid district of northwestern Nevada occur along steep fractures in Oligocene and Miocene quartz latite tuffs. The vein mineralization is zoned from a central enargite-pyrite zone outward through a complex polymetallic intermediate zone and an outer zone of galena and pyrite. Wall rock alteration includes advanced argillic and sericitic envelopes along veins superimposed on district-wide propylitization. The ore distribution and alteration patterns were probably produced by an increase in pH, a decrease in sulfur fugacity, along with cooling of the migrating hydrothermal fluid.

Jan 1, 1978

By H. H. Murray

Recently developed clay deposits that will impact regional and world markets are described. These deposits, their location, geology, and physical properties are delineated. Kaolins from the State of Para in Brazil and from Ukraine; bentonites from Argentina and India; and palygorskite and sepiolite from China are world class deposits that when processed using modem technology will produce excellent products. Other deposits that may affect regional markets are l<aolins from China, Australia and Indonesia; bentonites from Georgia (formerly USSR) and China; and palygorskite from India and Ukraine. New ball clay deposits that will affect regional markets are in China and Indonesia.

Jan 1, 1999

By Robert A. Blake

Introduction Sulfide copper, zinc and iron concentrates are recovered in the 5000 ton per day flotation plant operated by Cities Service Company at Copperhill, Tennessee. The heavy-sulphide ore is first ground to 50 pct. minus 200 mesh and a bulk concentrate floated. The bulk concentrate, over 60 pct. of the ore weight, is reground to 72 pct. minus 200 mesh and then treated in a selective flotation circuit to recover copper and zinc concentrates. The tailing of selective float is the iron sulphide material source for the manufacture of sulfuric acid and iron sinter. The valuable minerals in the ore are chalcopyrite, marmatitic sphalerite, pyrite, and pyrrhotite. A typical mineralogical analysis will be found in table 1. A typical material flowsheet will be found in figure 1. Shown in the flowsheet are a scavenger float on the bulk rougher tailing and a copper-talc separation unit. At times a lead-copper separation circuit has been run.

Jan 1, 1971

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of screens were developed for the Coal Cleaning Simulator running under Aspen Plus during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for the size separation and a calculation for moisture content of the oversize product based on particle size and specific gravity distribution. This paper discusses the algorithm for predicting the moisture content of coal dewatered by screens.

Jan 1, 1997

By Dirk van Zyl

Pad construction costs can impact the overall economics of heap leach projects. Pad construction costs for single-and double-lined pads, using various designs, are listed for a typical small and large project. Double-lined pads are now more often required by regulatory agencies. Unless such designs reduce the risk of site specific contamination significantly, the extra costs cannot be justified from an economical viewpoint. Specific attention is given to the short project life (typically five years) of heap leach projects. A few numerical examples are presented to demonstrate the overall economic impacts of these costs on economic parameters.

Jan 1, 1990

By John S. Lagarias

When ore bodies are faulted or mill feed turns refractory, mining managers and engineers act vigorously to convert imminent failure into eventual success. The recent proliferation of onerous "environmental" regulations and restraints is likewise a threat to successful mining enterprise, in some ways more insidious and dangerous than the problems presented by natural obstacles. The regulatory burden has become so heavy that a pall of pessimism covers much of the mining enterprise. In this paper we frankly recommend a Pollyanna approach, making not just "the best of it" but directing the whole environmental process: first, to improve our planning, engineering, and operating procedures; and, second, to demonstrate the need for modification of laws and regulations which are intolerably burden-some to both the mining industry and the public. It is customary for government officials and environmentalists to point out how great are the new environmental regulations and how successfully these have improved the natural environment in particular and the quality of life in general.

Jan 1, 1978

By F. F. Peng

For a given flotation system, the rate-controlling step in fine coal flotation can be the attachment of bubble to the fine coal particles. The probability of attachment depends upon the surface characteristics and the collector adsorption on the coal particle surfaces. Thus, to further improve the flotation rate and selectivity is to alter the distribution of hydrophobicity on coal particles efficiently by applying the effective means of collector dispersion. In order to enhance the combustible recovery and selectivity of fine coal flotation, and lower the amount of collector used in the fine coal flotation processes, four modes collector dispersion/addition techniques are tested. They are direct liquid addition in pulp (mechanical agitation), ultrasonic energy dispersed collector into pulp, atomized collector into pulp and gasified collector transported by air and formation of collector-air bubbles in pulp. The effect of four collector dispersion/addition methods on the floatability of -600 µ m (-30 mesh US sieve) coal samples from four ranks of coals were studied. The ultrasonic energy dispersed collector and atomized collector flotation processes enhance flotation yield and most significantly improve the kinetics of fine coal flotation. The gasified flotation process can increase the selectivity of separation and decrease the collector consumption due to starvation flotation is achieved in this process. The flotation efficiency of gasified collector process is as high as that of conventional flotation. It is because that the effect of the decrease in the combustible recovery is offset by the increase of selectivity. In addition to flotation experiments, induction times of bubble attachment to the bed of fine coal particles for four ranks of coals are measured.

Jan 1, 1992

By E. Berrezueta

Automatic digital phase imaging should yield unbiased and representative characterization of gold ores. However, this is not a simple task due to low gold grades, fine grain size, possible complex mineralogy, nugget effect, etc. A critical test was done by two methods, using the same sections of a gold-rich ore: with an optical (OM) and with an electron microscope (EM). In general, the two methods are consistent and useful for ore processing. There are some minor differences e.g. the detection of very fine gold grains is enhanced by EM.

Jan 1, 2001

By Frits Agterberg

Statistical exploration uses statistical methods to identify targets for more detailed investigation by estimating the odds of occurrence of mineral deposits. The study area which contains the possible targets may be as large as 1 000 000 km2 or as small as 100 km2. Results are presented in terms of a probability index for the existence of a deposit or, more precisely, in terms of expected dollar value for a unit area, or even in terms of number, size, and grade of deposits remaining to be discovered. Typically, selected geological, geophysical, or geochemical information is systematically quantified and statistically analyzed by using the computer in order to distinguish between geological environments on the basis of the probability that they contain undiscovered deposits of a specific type. All possible targets are compared with one another by using information on areas known to contain deposits. The information on the known areas is either a set of control data consisting of values for the same parameters as are quantified for the entire study area, or it embodies a specific model for the occurrence of a given deposit type. Examples of both procedures will be discussed in this chapter.

Jan 1, 1979

By Christopher Hebert, Michael R. King, Mehdi Ghazi

The Inland Feeder project is a critical component of Southern California’s water delivery system, relying on a strategic plan of water transfer and storage to enable the delivery of an additional 650 million gallons of water a day. The Arrowhead West and Arrowhead East tunnels form part of this system, comprising the construction of nearly13 km (8 miles) of bored tunnel under the San Bernardino National Forest. This paper describes the design and manufacture of the 4.88 m (16 ft) diameter precast segmental primary lining that will be used in these tunnels to resist rock loads, and up to 275 m (900 ft) of external hydrostatic head.

Jan 1, 2003

By C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA) system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By G. E. Erdman

The total attitude of the industrial minerals producing company is a most important factor in how they regard quality control, technical support for their customers, and procedures used in mining their minerals products. This philosophy of the producing organization directs their action along certain courses. For instance, one producer might see itself as a mining company with its major goal mining efficiency to make it exceedingly price competitive in the market place. Another producer might see itself as a wide spectrum multi-mineral producer that furnishes a reputation for a complete line of products. Another producer might see itself as a specialist in one specific industrial mineral and bet its whole bankroll on providing the very best of quality with the goal of becoming the largest producer of the mineral commodity. Each perception can have a different impact upon the producer&apos;s operations and its regard for quality control. Minerals Being Produced The specific markets being served will have their own influence on how mineral product quality is regarded. Ceramic raw materials, for instance, have a very low tolerance for iron which is the cause of low fired color. Thus, industrial minerals for use in glass and ceramic markets must be won from deposits with a very low iron content. A high iron silica sand might be sold to a manufacturer of good old beer bottles. That is a solution to one particular quality facet, but eliminates selling to a significant market in clear glass, porcelain enamel, ceramics whiteware bodies and hobby glazes. Thus, there is a need for sound research in the industries expected to be served before the product is brought to market.

Jan 1, 1987

By Frank Cook

As in other areas of the country, surface coal mine productivity in the Central Coal Province--primarily Illinois, Indiana, and west Kentucky--has declined steadily since 1969 (figure 1). Productivity, as measured in tons of clean coal produced per man-shift, dropped 35 percent during the period 1969-1975. Unwelcome at any time, this phenomenon is particularly untimely now, when increased coal production is a national goal. The U.S. Bureau of Mines has been working with the coal industry to develop new operating methods and equipment to enable increased productivity and improved reclamation performance in surface coal mining. Several projects have involved identification and evaluation of existing overburden handling and reclamation practices, and development of means to improve operational procedures. Some results of one of those projects, as they apply to the Central Coal Province, are summarized in this paper.

Jan 1, 1977

By K. Hanumantha Rao, K. S. E. Forssberg, F. Su

The influence of reagents dosage, pH, temperature, and particle size on the kinetics of apatite flotation response from magnetite has been investigated. The first-order models characterizing rectangular distribution and fast and slow distributions (F-S model) of floatabilities gave an excellent fit to the results of apatite flotation when compared to other models. However, the latter model is found to be better than the former in the goodness of fit and also in the description of flotation performance. The kinetic parameters in the F-S model are estimated by using a nonlinear least squares fitting program. The ratio of fast and slow rate constants is observed to be an important parameter for identifying the optimum levels of the variables and to outline the selectivity between apatite and magnetite. The influence of collector dosage is realized from the model parameters by relating it to the fraction of slow- floating particles. An attempt has been made to describe the apatite flotation behavior with the determined model parameters.

Jan 1, 1999

By R. H. Lambeth

Disposal of mine tailings in "waters of the United States" is presently prohibited even though case studies indicate that the practice may be environmentally viable. To simulate disposal in the natural environment, nine containers of tailings and sediment were instrumented and placed on the ocean floor near Juneau, AK as were ninety-six biosample containers. Pore water concentrations of five metals were determined, and biota populations were characterized for both materials. After 500 days of exposure there were no statistical macro scale differences between tailings and sediment biota populations or Cu, Pb, and Zn pore water concentrations. Tailings released slightly more Fe than sediment, but sediment released significantly more Mn than tailings. Disposal of mine tailings in marine waters may be environmentally safe.

Jan 1, 1998

By S. K. Kawatra

It is common in coal-cleaning operations to produce a fine waste stream which contains a considerable amount of coal, but which is not economical to recover both because it is mixed with large amounts of difficult-to-remove clay slimes, and because the fines are often heavily oxidized. Conventional froth flotation machines cannot produce an acceptable product from such material in a single stage of flotation, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and was installed and tested in a coal-cleaning plant in Ohio. The feed coal contained 39.8% ash as fine clay, and 2.83% total sulfur, and was 80% passing 176 micrometers. The coal was a thickener product which had oxidized for some time, and was very difficult to float. However, using the new column it was possible to recover up to 85% of the calorific value in a product containing less than 11% ash, and up to 60% of the calorific value in a product of less that 8% ash. The bulk of the pyritic sulfur was rejected from the coal as well. Multistage flotation tests showed that the flotation column was able, in a single stage, to produce the best froth flotation product that it was possible to recover from this coal.

Jan 1, 1994

By S. K. Singh

"Feather edging"-a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar (&apos;total&apos;) extraction coal mine.

Jan 1, 1999

By J. Fuller, L. Marsden

Windborne dust from alkaline salt flats and mining-related tailings ponds is especially prone to threaten applicable ambient air quality standards. Sodium carbonate crystals, typically present, weather to an exceedingly fine, non-cohesive dust, causing air quality problems for miles downwind. Recently developed specialized polymers react with alkaline dust to form sturdy, wind-resistant crusts with good longevity. An on-going demonstration project at a major trona facility has developed techniques for cost-effective application of these polymers over large areas of soft tailings or sediments in a wide variety of situations. Recently treated areas on the order of 80 acres show effective suppression of dust.

Jan 1, 2004

By Robert N. Pratt

The rapid acceleration and sweeping consequences of what we have all come to characterize as "the ecology movement" has marked a period of serious trial and challenge for the mining industry. It has blossomed into a major factor in our daily business and added a significant new dimension to the problems we must meet and overcome as businessmen. It has become an important new consideration at a time when we must continue to cope with our traditional problems such as rising costs, competition at home and abroad, and the always vital necessity to continually develop new and better technology to produce more minerals more efficiently and more economically. The body of law embracing environmental quality control grows each day, becomes more complex and offers more contradictions. And there is little relief in sight. The requirement to comply with sound environmental regulations -- or challenge unrealistic legislation -- has placed a major burden on the private sector. The economic significance of enacted and proposed environmental regulation is pressing management in the mining industry to some hard decisions -- basic day-to-day business decisions and decisions which acknowledge the undoubted long-term effects of the new laws.

Jan 1, 1973