Search Documents

By F. J. Sotillo

Mineral processing requires good classification of particles to attain an adequate separation of minerals. This is of utmost importance in the case of sulfide minerals. An ideal classification is obtained when particles are separated at a given mesh, which is fixed according to the characteristics of each sulfide ore. Under these ideal conditions, particles coarser than the mesh of separation are recovered in the underflow, whereas particles finer than the mesh of separation are recovered in the overflow. This paper presents the results of pilot plant tests that were performed on Ag-Pb-Zn and on Ag-Au Peruvian sulfide ores using a Density Separator, and the comparison of these results with those obtained using hydrocyclones, under similar operating conditions. The results show that the ratio of circulating load is reduced by 50% by using a Density Separator with respect to that obtained by using hydrocyclones. Moreover, the effect of the improvement in the separation efficiency obtained by using the Density Separator on the kinetics of flotation is also shown. Silver recovery of the Ag-Pb-Zn ore increased by 18% whereas gold grade in the concentrate of the Ag-Au ore is doubled.

Jan 1, 1998

By J. Y. Hwang

Coal cleaning with traditional magnetic separation usually yields unsatisfactory results because minerals associated with coal, such as quartz, clay, pyrite and calcite, are weak-or non-magnetic. Magnetic reagent technology is a new mineral processing technology with the capability to enhance the magnetic property of minerals selectively. This reagent can be adsorbed selectively on minerals through the control of surface chemistry and, thus, result in selective magnetic enhancement. The application of this technology on coal cleaning has been experimentally demonstrated. Good separation results can be obtained at low to medium magnetic field strength. Comparison with other processing technologies is included.

Jan 1, 1992

By Michel Gauthier

Several zinc showings, exhibiting many similarities to the well-known Balmat-Edwards zinc deposits of New York State, occur within the Grenville Supergroup strata of the Mont-Laurier Basin, Quebec. Metallogenic mapping programs have revealed much of the stratigraphic control of this mineralization. This control is observed on both regional and local scales. At the regional scale, these showings are confined to the perimeter of the Mt.-Laurier Basin, while at the local scale, a definite association between the zinc mineralization and dolomitic marble horizons is clearly exhibited from detailed mapping. These new exploration guidelines have proven to be useful for base-metal exploration in the Mt.-Laurier Basin and should be applicable to the entire Grenville Province.

Jan 1, 1983

By G. S. Dobby

The Cu-Au flotation cleaning circuit at Freeport Indonesia consists of three stages: two flotation column stages, in series, followed by one stage of mechanical cells. Concentrate from both column stages is combined as final concentrate. The mechanical cell stage has two parallel rows of seven Wemco 500's. The Wemco concentrate is recycled to feed of the second column stage and Wemco tails report to final tailings. This paper examines cleaner circuit performance, focusing on size-by-size performance of the individual stages and the individual mineral groups -copper sulfides, gold and in sol minerals. The recovery mechanisms of insol minerals are examined.

Jan 1, 1995

By M. R. Yalamanchili

The in-situ FTIR/IRS technique has been used to spectroscopically characterize interfacial water near a hydrophilic surface. Interfacial water was examined spectroscopically over known distances from the surface of a silicon single crystal by appropriate design of the geometry and optics of the internal reflection system. The in-situ FTIR/IRS spectra of interfacial water were examined by consideration of the 0 -H stretching region (3000 -3800 cm-1) associated with the vibrational spectra of water. The broad peak: in this region which describes the interfacial water structure was deconvoluted in order to isolate the overlapping spectral features of the interfacial water. Preliminary spectral results indicate the prevalence of an ice-like water structure (-3200 cm-!) at the silicon surface. Importantly, it appears that the interfacial water structure may extend a considerable distance (several tens of molecular layers) from the surface as established from the spectroscopic depth profile measurements which show that the free OH stretch at 3600 cm-1 becomes very significant at distances from the surface exceeding 400 nm.

Jan 1, 1995

By Kirk Carlton

This paper deals with a group of subjects so familiar to all of us that we might question the need for discussion. Even so, nearly every day's business turns up expensive examples of differences in understanding, misdirected assumptions and incomplete technical purchase documents. As our international activities increase, so do these problem areas. Their expense in both money and embarrassment gives rise to this attempt to focus a little extra attention on technical criteria and specifications. The two terms ?criteria? and "specifications" are, we believe, worth separating with respect to meaning. They should not be used interchangeably, although they often are. Criteria are by definition "standards for judging", whereas specifications are "enumerations of particulars". In relation to plant or project engineering, the criteria are the general rules and data which apply to the whole project and the specifications are the further listing of detailed requirements for specific contractual items or pieces of equipment. We'll look a little more closely at specifications after we give another minute or two to this "criteria" subject,

Jan 1, 1973

By Leons Kovisars

Two-thirds of the world copper produced in 1979 incurred cash costs between $0.35 and $0.89 per lb, averaging $0.62 per lb. North American costs are higher at $0.48, $0.88, and $0.68 per lb, respectively. Variable cash costs are $0.20, $0.58, and $0.39 per lb for the world; $0.29, $0.63, and $0.46 per lb for North America. Cash costs are relevant for comparing existing operations and evaluating market pricing during periods of excess supply. Analysis of full costs of production (cash costs plus income taxes, profit, and non-cash items) becomes relevant in evaluating the incentive price required to develop new production plants. In mid-1979 this cost (incentive price) was about $1.10 per lb; it is expected to approach $2.00 per lb by 1985.

Jan 1, 1979

By H. F. Anderson

The Palabora Mining Company Ltd. is probably best known for its production of copper since 1965. The success of the PMC mine lies in the outstanding technical and highly organized efficiencies applied to the massive mining, transportation, and treatment operations necessary to produce profitable copper. We are not however going to discuss the well-known copper operation but the extremely successful recovery and marketing of Baddeleyite by the PMC group. Let us first review the extraction process at the Heavy Minerals Plant. Non-magnetic ground ore from the copper magnetic separators is processed in the Heavy Minerals Plant for the extraction of the "heavy minerals" uranium and zirconia (Baddeleyite). Thorium is also present as a potentially recoverable mineral. The content of the minerals in the feed is probably the lowest in the world to be treated commercially. Minerals are separated from the waste ore by a gravity separation process in which the high density minerals segregate preferentially in a waterborne system.

Jan 1, 1985

By O. W. Kamper

To most of you present here the word "refractories" is not new and you are familiar with the materials and use. To many people though the question is asked, "What are refractoriness and what are they used for?" Refractories are non-metallic products which are so resistant too melting at very high temperatures that they can be used for building or lining furnaces of all kinds. A large variation occurs in the size, form, and composition depending on the service for which they are intended. They are made from a wide variety of raw materials, of which fire clay and quartzite are used in largest quantities. Other refractory raw materials include magnesite, chrome, diaspore, bauxite, kyanite, sillimanite, olivine, zircon, and many others. Most of these are assembled from-widely-'separated points in the United States while others come from the far corners of the earth. Chrome is imported from the Philippines and South Africa, and, to a lesser extent, Turkey and Greece Kyanite and sillimanite come: from India and bauxite from the Guianas. And there's "magnesite from brines," produced in chemical plant's by treatment of sea water or inland deep-well brines with hydrated lime. The proportion of magnesia available in sea water is so small, less than one pound from 500 pounds of water,, that millions of gallons must be pumped and processed each day in a sea water magnesite plant. The realm of refractory raw materials, therefore, is very extensive and continues to grow because of the endeavor to find-better raw materials from which to produce better products for refractory service.

Jan 1, 1960

By Christian F. Baiz

Industrial minerals can have similar financing requirements to those needs of metaliferrous and coal mining projects. Although, one may see many similarities in the fundamentals of the various risks that must be evaluated in lending to any specific project, one of the outstanding differences is the understanding of the many different markets that these industrial minerals represent. There are in excess of 30 principal industrial minerals ranging in terms of annual production from the largest quantity such as sand and gravel, to possibly the smallest quantity of production of a legitimate industrial mineral which may be defined as industrial and rough gem diamond. If we assume that it is necessary to finance independent projects of ore bodies of industrial minerals for development, the financing techniques are similar to the fundamentals that we would use for financing coal projects or metaliferrous deposits. Therefore, let's begin by redefining project financing in the traditional banking or private sector area, and then in the later development of this paper, we will apply these techniques to industrial minerals in general and cite it with several specific examples.

Jan 1, 1982

By R. H. King

Suboleski and King (1990) analyzed the reasons for the dramatic increase in underground coal mine productivity during the last 10 years. This paper examines whether this increase can be extended. The paper forecasts whether the mix of technological, procedural and other factors that produced the increase will change in the future. The forecast is based on the base case and spreadsheet production model described in the previous paper.

Jan 1, 1991

By R. J. Bridwell

Acid mine drainage (AMD) occurs in high sulfur coal and heavy metal mining environments. We show remediation methods using 3D numerical ground water flow models and chemical kinetics of pyrite oxidation for acid leaching of pyrite during air and ground water flow. A recently developed numerical model couples air and water flow with kinetics of iron-reactive bacteria, oxygen transport, specific chemical reaction rates, and pyrite oxidation to calculate migration control of pollution. A model is presented which considers diminution of acid mine drainage in pyrite rich ore bodies by raising the potentiometric surface through a vadose zone to reduce acid mine drainage. A ground water model is presented of an initially saturated mountain, containing an adit, with a sloping ground water table. Ground water recharge consists of snowfall and normal precipitation. Simulations indicate that the historically open adit creates a desaturated mountain above the adit. Significant air saturation ranging from 10-90% oxygen can occur to depths of the adit (-270 m). Remediation consists of plugging the adit, which fill s adit and mountain with water from recharge. Plugging the adit required <10 years for resaturation and rise of the water table in the mountain.

Jan 1, 1994

By L. M. English

In the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed, and who has performed the research have all changed significantly over these decades. Although there are a lot of subjective ideas concerning these changes, and there is a fair amount of anecdotal "analysis," there has been no actual study of these trends to verify the facts. The period studied is divided into six five-year periods for the purposes of comparison. Some of the trends analyzed are as follows: ? Co-authorship ? Research areas ? Research sponsors ? Cooperative efforts

Jan 1, 1995

By L. M. Gochioco

The U.S. coal industry is under-going dramatic changes to meet the challenges of the keenly competitive fuels market. The application of innovative technologies is needed to improve safety and to increase productivity in order to make coal more competitive as a fuel. As more coal companies shift into capital intensive longwall mining, there is a clear need to invest more in exploration before mine plans are made. Coal seam anomalies may create adverse mining conditions. The early detection of these anomalies could make the longwall mining safer and more productive through improved planning. A standard exploratory drilling program can provide only limited geologic information. The seismic reflection technique can be used to detect coal seam anomalies and is effective in reconnaissance surveying. Recent advances in the quality of coal seismic data have increased the success rate of seismic surveying. Therefore, surface seismic surveys, coupled with selective drilling, will come to play an integral role in coal exploration in the 1990s.

Jan 1, 1990

By K. Chandrasekaran

Carbon-in-leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. The CIL process is becoming attractive even in other situations when preg robbing is not a factor. This article discusses the situations in which the CIL circuit can be applied. The results of leach-carbon-in-pulp (CIP) and CIL circuits at Newmont Gold&apos;s Mill No. 2, No. 4 and No. 5 are presented for comparison: Mill No. 4 was initially designed for a throughput of 4.1 kt/d (4500 stpd). It is presently operating at an average throughput of 6.6 kt/d (7300 stpd) without significant changes to the original design. The design considerations of the Mill No. 4 CIL circuit are discussed. The design of any processing facility represents a series of decisions. The final design options should ultimately be resolved based on economic as well as technical considerations. Every design decision represents some sort of compromise. From the designer&apos;s view point, these decisions are made with the conviction that the final product represents the most prudent long-term expenditure. The design throughput rate is a decision reflecting a maximum return for the capital and operating costs that the plant will incur over the life of the mineral resource. The result is a plant that is not operator proof or maintenance free because it would be too costly to build. At some point, the incremental increase in the level of capital expenditure would not adequately compensate for the lower

Jan 1, 1991

By R. R. Young

Prior to 1903, the world&apos;s supply of sulphur was primarily from surface deposits in Sicily. The discovery of the first salt dome sulphur deposit in 1867 and successful development of the Frasch process for recovering the sulphur resulted in a large part of this essential element being supplied from these mines since 1920. Although the basic process is the same today, engineering and technological developments have evolved to allow its application under many adverse conditions. These and other challenges for the industry in today&apos;s environment will be discussed in the paper.

Jan 1, 1979

By John T. Cantwell

INTRODUCTION The process engineer usually is responsible for the design operating philosophy and/or day-to-day operations of a process. Since instrumentation is an integral part of the operation, it is essential that engineers understand the general capabilities of the different types of control equipment available. Many "noncontrol" engineers have become involved with instrumentation for machinery monitoring and control as well as other plant applications. The advent of the microprocessor has led to significant changes in control, both in systems configurations and man-machine interfaces. Today&apos;s concept is called simply "distributed control." What is distributed control? Distributed control is exactly what the name implies; the control system is divided into several functional segments and spread out to cover a process. The systems are distributed for physical, functional, and risk reasons. Before delving further into the specifics of distributed control, let&apos;s look at the evolution of control systems to see how we got here. Instruments initially were located near measurement and control points in the field. Operators physically had to go to the instrument to change setpoints or take measurements. As processes became more complex, it became evident that a central control area was required. This allowed an operator to monitor and control many variables. The operator&apos;s effectiveness was increased dramatically, which resulted in greater efficiency, better quality control, and lower personnel requirements. At the same time, plants became much larger, control applications became more complex, energy became expensive, and the industry became more competitive. All of these factors placed pressure on process and production engineers to get the most for the money. The result was a continuing push to put more instrumentation into a central control room to maximize efficiency and productivity and minimize manpower. This chapter deals in some detail with devices for measuring physical and chemical properties of coal; devices for measuring the weight and weight-rate of flow of coal; devices for the monitoring and control of conveyor systems, solids inventory, fluid flow, liquid level, density, and specific gravity. These instruments have a multitude of uses throughout a coal preparation plant. The discussions cover advancements in "on-line analysis," nuclear control devices, and distributed control using microprocessors, mainframes, and soft-

Jan 1, 1991

By B. J. Scheiner

The Bureau of Mines, U.S. Department of the Interior, has investigated the use of rheology to provide insight into the mechanism of flocculation. A technique developed by Tattersall has been modified and used to explain the flocculation of calcium montmorillonite with polyethylene oxide. The results indicated that there are two types of bond systems operating during the flocculation sequence. Also, flocculation results are highly dependent on the shear rate and the amount of polymer added.

Jan 1, 1989

By Thomas R. Hightower

The Thunderbird plant was erected in Sullivan County in Indiana during 1958-1959. It was first put in operation in March of 1959. At the present time the source of the raw coal is from the Indiana No. 6 seam. The underground operation at present consists of two continuous mining units and two conventional units. The underground is all belt haulage and the first unit with which this paper is concerned is the slope belt. It is a 48-inch-wide inclined belt with 980-foot centers and a lift of 275 feet. The belt is powered with a 350 H, P, motor and has a rated capacity of 600 Tons per Hour. The belt is equipped with a Merrick Scale Company Weightometer, The raw coal moves from the belt to a 6&apos;x12&apos; extra heavy Allis-Chalmers Ripl-Flo equipped with 6" round-hole screens. The over product of the screen is fed into a 10&apos;x20&apos; long McNally- Pittsburg rotary breaker equipped with 4-l/2" round-hole screens. The oversize rock is discharged into a bin that is emptied with a refuse truck. The through-product of the breaker, along with the through-product of the Ripl-Flo, passes either directly to the McNally Giant washbox or to a 36" belt that transports it to a 1000-ton storage bin,&apos; The change from either to the washbox or to the storage bin is made by use of a motorized gate controlled by the plant operator,

Jan 1, 1961

By J. S. Chung

As part of ongoing deep-ocean mining research, hydraulic transport systems as well as status of deep-ocean mining systems are reviewed in the aspects of manganese nodules and crusts from 800-6,000-m depth. The emphasis of the investigation of hydraulic transport is placed on the shape effect of particles on the pressure gradients and flowrates. Series of tests are being conducted to study the lift characteristics of a 2-phase vertically upward hydraulic transport of 2 types of small solid particles in a PVC pipe of 1-in (2.54 cm) diameter: irregular-shaped silica sands and equivalent spherical glass beads. Pressure drops and mass as well as volumetric flow rates were measured by electromagnetic (EM) flowmeter and mass flowmeter. The particle sizes used are 8-10 mesh. The results in turbulent flow range of 104 < Re < 105 show that pressure gradients or friction factors are smaller for the spherical beads than the sands. The larger the concentration of the particles are, the larger the pressure gradients become. The larger the particle concentration is, the less the effect of particle shape on pressure gradients becomes. The shape effect is greater for the minimum particle transport velocities than for the settling velocities.

Jan 1, 1999