Search Documents

By D. D. Schlepp

There is a continuing debate about the influence of circulating load and classifier efficiency on the capacity of the circuit. Specifically, the effects of preferential classification, bypassed fines, and the sharpness of classification will be examined. Horizontal cyclones have also proven to be very successful in a number of operations but their impact on the circuit capacity has not been clearly defined.

Jan 1, 1990

By V. P. Mehrotra

The effect of dissolved ions present in plant water on the flotation of phosphate ore from central Florida was investigated. Of the three most abundant ions, namely Ca++, Mg++ and SO4--, calcium ions were the most detrimental in the flotation of phosphate with sodium oleate collector. In one feed, a 10 ppm concentration of Ca++ ions reduced the BPL recovery from 86% to 46% whereas in the other a 40 ppm concentration lowered the recovery from 90% to 52%. The effect of Na2C03, NaHC03, Zeolite and EDTA to remove ca++ ions from water and hence improve apatite flotation was also studied.

Jan 1, 1986

By D. Diggins

Experimental apparatus for the determination of powder wettability is described. The principle of the technique is based on the measurement of the equilibrium capillary pressure in a packed bed of particles. Both the macroscopic solid-solution-vapour contact angle, e, and the specific surface area, A(m2g-1), of the powder, can be obtained. Experiments on angular quartz particles have been performed. A wide range of situations have been covered: hydrophobic and hydrophobic particles wetted with water, a variety of organic liquids and solutions of surfactants. The results show that reliable and reproducible values for 0 and A for angular and relatively coarse powders can be obtained with the proposed equipment for advancing liquid fronts in the absence of soluble surfactants. In the latter case and for receding liquid fronts in general, only qualitative trends have been obtained.

Jan 1, 1992

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

By James A. Jessop

The Bureau of Mines is investigating the use of geophysical methods to determine rock mass characteristics, particularly rock quality, lithology, and fracture parameters that are important for determining the feasibility of in situ leaching operations. As part of this research, two Bureau-developed crosshole geophysical systems are described that can be used for site investigation and rock mass characterization. Results are given for performance tests at field sites in Arizona and Texas and for correlations between the crosshole seismic data with fracture frequency, rock quality, and lithologic variation. Recommendations are made for using elastic waveform propagation characteristics and dynamic elastic properties for improving rock mass characterization in the geomechanical assessment of in situ leaching deposits.

Jan 1, 1990

By Robert C. Freas, Donald D. Carr, Lawrence F. Rooney

Perhaps no other mineral commodities in this volume have as many uses as limestone and dolomite. These carbonate rocks are the basic building blocks of the construction industry, the material from which aggregate, cement, lime, and building stone are made. Carbonate rocks, and their derived products, are used as aggregates, fluxes, glass raw material, refractories, fillers, reactive agents in sulfur-oxide removal, abrasives, soil conditioners, ingredients in a host of chemical processes, and much more. Although the use of limestone and dolomite goes back before recorded history, new uses and products are continually being found. Carbonate rocks form about 15% of the earth's sedimentary crust and are widely available for exploitation. Found extensively on all continents, they are quarried and mined from formations that range in age from Precambrian to Holocene. Reserves of carbonate rock are large and will last indefinitely, although high-purity deposits may be absent or have limited availability in certain areas. Limestone and dolomite are so useful and so abundant that in 1989 about 798 Mt were produced in the United States. In fact, about 75% of all stone quarried or mined in the United States was carbonate rock. Sand and gravel was the only mineral commodity produced in greater quantity. In this chapter we have sought to provide the general reader an overview of carbonate rocks, their composition, distribution, production, and uses. The literature on the limestone and dolomite resources of the United States and Canada is so vast and diverse that one can easily become mired in print. We tried to list those references that are easily accessible and that provide the economic geologist with a starting point for more intensive study. The table listing selected references on limestone and dolomite resources in Canada and the United States reflects our attempt to be selective rather than exhaustive and to direct the reader to the best sources of detailed information.

Jan 1, 1994

By Howard L. Hartman

The federal government's declining role in funding research has created a critical dollar gap for university departments of mining engineering. Industry is not unaffected by the drought: not only is research lagging, but hard- pressed universities are going to the private sector for funding. This paper's thesis is not that mining companies should shower universities with philanthropy, but that a quid pro quo ought to be exacted: a research partnership should be contracted on a pay-as-you-go basis. A model exists at The University of Alabama (albeit not in mining) that may lend itself to adoption by our industry.

Jan 1, 1984

By Joseph D. D?Annunzio

The report on cut and cover construction as assembled by the Organization for Economic Co-operation and Development covered 17 different countries based on a total of just under 400 individual replies of which about 30% of the replies were from the United States. In general, the review of replies to the questionnaire led to the impression that cut and cover construction is a very inadequate method which needed many improvements. This unfavorable judgment, however, resulted in the manner in which questions were asked rather than in the method itself, It can be concluded that the cut and cover construction method has proved itself as an excellent method and that it has reached a high degree of technological perfection, but inadequacies stilt exist, and for purposes of complete evaluation, comparisons with mining tunnelling methods should be carried out. The principal problem in cut and cover construction is the interaction during construction between the construction process and the existing use of the surface and subsurface environment. The greatest impediments to cut and cover construction have little to do with the physical works being constructed, but more with creating a site in which the work can be performed. Utility relocation, traffice maintenance, and protection of existing structures are major problems for the construction contractor, and too frequently receive insufficient attention in preconstruction planning and design. Some OF the areas in which research should be undertaken are as follows:

Jan 1, 1970

By Christian F. Baiz

A new agenda has risen. Born out of governments' policies and world economies, the years ahead will carry with them reduced growth. For inflation dependent and capital intensive industries, such as metals and mining, as well as most other natural resource industries, a period of long-term contraction in outmoded and costly capacity will evolve. This will be supplanted by new, lower cost capacity in some cases, but only if the total cost of production, including cash operating and debt service costs comes in at or below current market conditions. The industrial outlook can be characterized as bearish. As one major U.S. bank economist put it, mining companies planning their five-year forecast from 1984 out, should take the current market conditions and straight-line them to the end of the decade. With low growth and low inflation, the real price of metals will remain flat or slightly declining. As a result, capital funding will be problematic. The low cost producer, that is one with low cash costs and low principal and interest costs per unit of production, will succeed.

Jan 1, 1984

By E. B. Fitch, D. A. Dahlstrom

Liquid-solids separation is common to practically all mineral and coal processing as the bulk of beneficiation plants employ water as the major processing vehicle. The growing usage of hydrometallurgy has increased the importance of liquid-solid separation as acidic and basic solutions result in greater amounts of colloidal solids, with their consequent greater difficulty of separation, the economic need for chemical recovery to minimize this operating cost, and the usual necessity of employing more costly construction materials. The three processing steps covered in this section have significant capital costs. Drying, particularly, has an important operating cost because of the obvious need for energy to evaporate the water or solvent. Several common factors influence all three liquid-solid separation steps. Particle Size and Size Distribution. In general, finer particles have slower settling and filtration rates. The specific surface area is increased, which means a lower solids concentration in the thickener underflow and discharged filter cake as well as a grater moisture content to be evaporated in the drying step. Therefore, overgrinding or excessive attrition should be avoided. Consideration should be given to optimum particle size consistent with entire plant operation performance and recovery. Solids Concentration. Increased feed solids concentration will generally minimize required equipment size and costs in all three liquid-solid separation steps. Most thickeners are designed on the basis of unit area required, expressed as square feet per short ton of dry solids per day (square meters per metric ton per day) which will usually decrease with increased feed solids concentration. Filtration rates also increase as the required flow through the capillaries of the filter cake decreases. Dryer capacity increases and less energy per ton of final product is required to evaporate the associated moisture. Particle Shape and Surface Characteristics. Generally, optimum shape is a spherical particle of zero porosity. As either of these factors degrade away from the desired state, difficulty increases. This is particularly true in drying, where porosity can decrease drying rate significantly if the moisture must first reach the particle surface by diffusion

Jan 1, 1985

By Charles E. Mauk

In 1970, recognizing the great need for an economical, high capacity chemical oxidation process for wastewater treatment, Houston Research began a fundamental study of the available technology, Included was waste characterization; oxidation chemistry for molecular oxygen, ozone and catalyst initiators; kinetics of reaction; gas-liquid contacting methods; and optimization of staged reactors for mixed wastes. Although ozone is the most powerful oxidizer available, the literature contains contradictory reports of its speed and effectiveness. It is now felt to be most likely that many of these early investigations were limited by the ineffectual transfer of ozone from the gas phase into the liquid, and so the investigators were really observing the effects of mass transfer and erroneously trying to interpret the results as if they were chemical reaction data. HR's work considered the cost and effectiveness of gas-liquid contacting in a packed tower, gas sparged contactor, ejector with hold-up tank, and a completely mixed, sparged contactor. The sparged, mixed contactor was found to be most effective and least expensive, and a later investigation settled on the reactor configuration shown in Figure 1 because of its effectiveness of mass transfer and because it lends itself to direct scale-up techniques using laboratory data to design larger reactors.

Jan 1, 1975

By Stephen Krickovic

"Bleeding", as used in mine ventilation language, has a number of meanings among mining men and is regarded with different degrees of importance. This lack of uniformity stems from a number of specific situations. A method that is adequate in a mildly gaseous mine may fall short in a very gaseous mine. Projected bleeders could be dependable under a certain type of roof, and totally unsatisfactory under a different type. Similarly a plan of bleeders can be rendered useless due to undulations of seam and water in one mine and function well in another. Finally, what is effective in a mining system with partial recovery will not suffice with full recovery. You may wonder, then, if there is a common denominator for the essential function of "bleeding". In my opinion, there is, and it can be defined as controlled movement of air across an active pillar line toward the back and outby ends of the adjacent gob area into the headings provided for the purpose. The objective is to maintain as methane-free as practicable a belt adjacent to the working places, so that, if face ventilation is interrupted temporarily, the gas will not accumulate in dangerous volumes at the working faces before ventilation is restored. It's possible for these temporary interruptions to be unnoticed in time or at all. In such cases, ineffective bleeding could cause a disaster. This has happened. To control, there must be power. That is to say, there must be adequate air, pressure differential between the front and back ends of a pillar line to facilitate proper regulation for diverting of air to the various portions of the gob and as far away from the active section as is practicable. As an indication of the importance of pressure, it is noteworthy that one may provide and maintain in a reasonably open condition a heading or two for a bleeder system and fail to obtain effective bleeding .because air pressure differential is inadequate. On the other hand, you are all familiar with the fact that pillar lines in some seams can be ventilated adequately by air flow straight across the gob when the section is near a main return shaft and thus obtains a heavy pressure differential.

Jan 1, 1962

By Carson Sharp Beltch

The determination of aqueous cyanide is accomplished by either detection in the sample as collected or by removal of the cyanide of the collected sample, followed by detection. The direct determination of the cyanide content of a solution can only be used in the simplest of systems, since many interferences can result in errors. Thus the most widely used method for total cyanide determination involve the reflux distillation of the sample using heat, acid and vacuum or air flow. The basic theory underlying this analytical approach is that by reducing the pH, the quality of molecular hydrogen cyanide will be in- creased and can be removed from the solution by elevating the temperature. The hydrogen cyanide is then collected in a caustic solution and analyzed. The general approach of removing the cyanide from the sample by distillation represented a major advance in this area of analytical chemistry. It enabled the determination of cyanide in many additional types of samples. When it became apparent that the tightly bonded cyanide complexes were not being detected by this approach, many methods fox complex ion destruction were proposed. These methods usually involved low pH adjustment with oxidizing mineral acids, coupled with the catalytic decomposition of the tightly hound complexes. All off the complexes except the strongest could he broken by these methods. The catalytic reflux distillation step has been found to have some negative aspects, since many materials that can be distilled with hydrogen cyanide will interfere with the color development step and result in a false positive reading.

Jan 1, 1981

By Patrick Hannon

In this presentation, it is intended to briefly describe some occurrences of lead-zinc mineralization in Mississippian carbonates of central Nova Scotia. Results of geophysical and geochemical prospecting are presented. Because the deposits do not give positive identification to these indirect techniques, it is necessary to site exploratory drilling through the development of geological concepts.

Jan 1, 1975

By S. Frimpong

The coal mining industry is an important sector of Canada?s economy. The cost of mining and haulage of coal in Western Canada is a major focal point when compared to inexpensive coal from Australia. Spot coal price volatility affect contractual price arrangements and this creates pressure on companies? profit margins and their competitive edge. In order to alleviate this pressure, companies may have to take short-term drastic measures that may hurt their strategic positions in the long-term. Companies must also create a mix of their products to ensure effective maintenance of profit margins given various quantity and quality constraints. In this paper the authors provide extensive analysis based on detailed probabilistic production systems for coal extraction and haulage in Western Canada. An optimization model is formulated for typical coal mining operations, processing and haulage from mine sites to the Vancouver Ports using linear programming algorithm. A stochastic model is also formulated to analyze the associated risks and uncertainties. These models are validated using data from five operating mines in Western Canada with varying quantity and quality products and uncertainties. The results show that the five mines studied have to produce between 180,000 and 2.10 million tonnes of metallurgical coal and between 70,000 and 2.16 million tonnes of thermal coal to enhance their profitability given the underlying constraints. The average expected probability of success associated with production capacities from these mines is about 66%. This results in a failure probability of 36%, which is extremely high under contractual arrangements. The results also show that management?s profit expectation of $83 million can be achieved at a zero percent failure probability. With a higher risk of failure of 10%, this expectation increases by 21% to $100.3 million.

Jan 1, 2011

By Thomas E. Howard

Engineers today face a tremendous challenge. Growing population and rising standards of living all over the world are creating unprecedented and accelerating demands on and for all kinds of technology. At the same time, the public is becoming more and more conscious of--and concerned with--the impact of technology on human welfare. The growing controversy over the Supersonic Transport is a case in point, It is clear that the modern engineer must expect to spend a growing share of his time considering this dilemma and evaluating the tools that are available to him, not only with respect to their adequacy for the job at hand but also their capability for meeting the increasingly demanding--and, in many cases, conflicting--requirements of the future. This meeting seems a particularly appropriate place to speculate about the future of mining technology. The summary of the state-of-the-art in surface mining contained in the papers scheduled for the International Conference, together with the recently published Surface Mining volume, constitute not only a major contribution to the technical literature but also form an impressive record of technologic progress. That record, and the advanced technology displayed in the exhibits, and to be discussed in the SME technical sessions demonstrate engineering achievement in which the mining community can justly take pride.

Jan 1, 1968

By Derek J. Barratt

The specification of the prime mover of an autogenous/semi-autogenous mill involves an analysis of the likely operating conditions within the mill and the choice of a nominal operating speed. For variable speed mills, the operating range for mill speed has to be defined so that mill power/torque requirement can be matched by the motor power/torque capability. This paper will describe how this relationship can be influenced by ore grindability.

Jan 1, 1993

By Henry W. Brandt

What is the most practical method for storing a huge quantity of crude oil for a long period of time to assure availability if conditions curtail the source of supply? Underground storage is a logical answer. But can abandoned mines be used for this purpose? That is the proposal Fenix & Scisson International, Inc. submitted to the S.F.F. Association (acting in behalf of the Department of Industries of the Republic of South Africa), Johannesburg, South Africa, in October 1966. This engineering and contracting firm with headquarters in Tulsa, Oklahoma, specializes in underground storage; and based upon previous experiences their engineers were reasonably certain that a mine could be used for storing crude oil. The answer subsequently proved to be "yes." The result was con- version of a coal mine to provide storage for a quantity of crude oil which is the equivalent of a sizeable oil field. The total cost of purchasing, testing, and converting the mine was less than 15 percent of the cost of conventional steel tanks. Operating and maintenance costs are proving to be about 2 percent of those experienced at two large tank farms owned and operated by the Association.

Jan 1, 1973

By C. S. Wageman

Staying competitive in the highly aggressive Powder River Basin is a challenge facing all operators. Any advantage that a mine utilizes to improve productivity and reduce costs could mean the difference in the tight spot coal market. Technological advances in mining equipment and data acquisition at the Eagle Butte Mine in Gillette, Wyoming result in productivity gains and increased maintenance awareness. A new overburden haulage truck fleet with an onboard payload and fault monitoring system interacts via telemetry with the loading shovel and PC's located in production and maintenance offices, enabling staff to monitor production and maintenance on a real-time basis. This paper will describe the system and highlight the benefits realized as a result of its implementation.

Jan 1, 1996

By T. H. Combs

Increased productivity in the U.S. underground coal industry has taxed pre-existing conveyor belt haulage systems. The usual remedies are costly and can disrupt production. A reduction in the belt feeder discharge rate on mobile haulage sections results in more uniform loading and reduces the spillage vulnerability. An investigation is made to determine the effect, if any, on shuttle car discharge time arising from lower feeder discharge rates. A five-section, underground mine is visualized, and belt spillage is introduced. The sectional feeder discharge rate is progressively lowered until spillage is precluded. At each level, the simulated spillage is measured and compared to the loss in face production. Methods of predicting the loss in face production from lower feeder discharge rates are discussed.

Jan 1, 1993