Search Documents

By R. K. Mehta

Stirred ball mill feed used for ultra-fine grinding application requires fine size separation step in order to avoid over-grinding. This paper presents the selectivity curves obtained for oil shale and complex sulfide are using 460 mesh (30 micron) Derrick vibrating screen. Interestingly, the selectivity curves generated from the experimental data were monotonic increasing selectivity for oil shale but not monotonic increasing for sulfide ore. These non-monotonic increasing selectivity curves were similar to the mechanical air separator fishhook selectivity curves described by Luckie and Austin. A 2 stage classification in series model describing the fishhook selectivity curve has been used in proposing the classification mechanism for fine vibrating screens when heterogeneous multicomponent sulfide are undergoes size separation.

Jan 1, 1992

By Clarence A. Johnson

The discovery of the Prudhoe Bay field temporarily reduced interest in the development of coal conversion processes, but interest is being re¬newed by the current energy crisis. According to M.A. Wright, Chairman of the Board of Humble Oil and Refining Company(l), the reserve in the Prudhoe Bay bield has been confirmed to be about 10 billion barrels. At first glance this appears to be an extremely large reserve which will eliminate supply problems for the United States for some time. This feeling of security is lost when one realizes that by 1980 the world will consume the reserves of a Prudhoe Bay or a Libya, or Venezuela in less than a year, based on the recent predictions of U.S. and world reserves made by Eastman-Dillon, Union Securities Company(2). Recent forecasts of U.S. demand and source of supply made by Kenneth E. Hill of Eastman-Dillon are shown in Figure 1. This forecast shows a decline in domestic supplies (excluding Alaska) after 1973, with the total domestic supply leveling off in 1975 at about 13 million barrels per day. Since the predicted demand increases from about 14 million barrels per day in 1970 to about 20 million barrels per day in 1980, about 35% of domestic consumption must come from imports or non-conventional sources by 1980. More imminent is the shortage of low sulfur fuel oil which has been created by the new, tough air pollution regulations that are basically legis¬lating eastern coals out of the market. As an alternate to importing large quantities of low sulfur fuel oil or importing and desulfurizing regular fuel oil, one of two domestic solutions is possible: stack gas clean-up or solids fuel pretreatment. Stack gas clean-up may be the cheapest approach for old installations, but fuel pretreatment has real advantages for new installations. Coal pretreatment at the mine could eliminate all solids fuel handling

Jan 1, 1972

By F. J. Susko

The Bureau of Mines investigated rapid bubble-pulp separation to improve flotation kinetics. A shallow-depth froth separator was employed to quickly recover the mineral-laden bubbles from a mixture of ore, water, and air bubbles. The shallow depth minimized the rising distance required to recover even the smallest size bubbles (100 ~m). Therefore, the slurry remained in the unit only long enough to recover the bubbles before the pulp exited through the conical bottom. Joining this unit with a rapid bubble-particle attachment unit, a rapid flotation system was formed that floated silica from phosphate in one-fifth of the retention time for conventional mechanical cells. The hydrodynamics of the rapid flotation system along with fundamental parameters for scale-up are presented in this paper.

Jan 1, 1992

By Del Brock, Dan Wooton

The design/build of two adjacent vertical mine shafts in difficult ground conditions at a mining complex in the midwestern United States required innovative construction techniques. Construction of the 267-m-deep Service Shaft required full depth dewatering wells and ground freezing. Blind drilling was utilized to excavate the 257-m-deep Production Shaft and it was finished with a steel/concrete composite liner that was floated into place. An equally unique component of the installation included supplying a high capacity vertical conveyor system, featuring a 273-m-lift. Other components of the project include the mine level development, as well as the design and installation of three hoisting systems, including a 45-ton capacity men/materials hoisting system.

Jan 1, 2003

By P. Zhu

The leaching behavior of copper powders recovered from waste printed circuit boards (WPCBs) was investigated using electrogenerated chlorine and aeration in a sulfuric acid solution with added NaCl and CuSO4. Various parameters were studied to understand the mechanism of the copper leaching. When the current density increased from 0 to 0.1 A/cm2, the temperature from 30 to 60° C, agitation speed from 100 to 400 rpm, and the size ranged from below 75 to 150 µm, the leaching ratios of copper powders increased. The leaching kinetics were analyzed using a shrinking core model: 1-(1-X)1/3 = kt, and the leaching process was chemically controlled with an activation energy of 14.7 kJ/mol due to Cl- ion catalysis. The ratios of [Cu+]/[Cu2+] at various temperatures (30, 40, 50, 60 and 70° C) showed a periodic variation with the increasing of the leaching time. The redox potentials of the leaching solution and copper leaching ratios in different conditions were measured. The result indicates that dissolved oxygen achieved the dissolution of coppers and electrogenerated chlorine can promote the dissolution of copper powders and improve the reaction rate of kinetics in the presence of oxygen.

By F. G. Rinker

The world demand for metallized iron continues to increase, keeping pace with steelmaking requirements for lower cost hot metal. Virgin iron ore and in-plant oxide fines can be reduced to direct reduced iron (DRI) and hot briquetted iron (RBI). MR&E has developed an improved coal-based process for cost-effective production of either DRI or HBI. Starting with dry compaction, the process combines the latest technology for material preparation, rotary hearth furnace construction and environmental control. Coarse iron ore fines are blended with pulverized non-metallurgical coal to produce a highly metallized (>90%) product. This paper presents production and installation cost data based on operating and under-construction iron oxide reduction facilities.

Jan 1, 1999

By H. Akgun

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. This paper presents the results of push-out tests on cement grout plugs in salt. Two expandable cement grouts have been tested. The average interface shear strengths ranged from 2 to 12 MPa. Peak shear stresses at failure, assuming an elastic stress distribution along the interface, were up to eight times higher. Standard deviations commonly reached 20%. Dissolution along the interface was observed, and may have been enhanced by clay inclusions in the salt. This dissolution appears to have reduced bond strengths. Application of the results to the design of plugs for larger openings (e.g. shafts, drifts, or boreholes) is discussed.

Jan 1, 1991

By David Conover

The El Boleo Copper Project is currently in the final design stages for development of a 3-MM-tonne/yr underground copper mine located in Baja California, Mexico. The nearly horizontal mineralized zones are amenable to exploitation by conventional mechanized coal mining technology using continuous miners, shuttle cars, and belt haulage. The mine design resembles a typical full-extraction coal mining operation utilizing a sequence of mains, sub-mains and production panels. Due to numerous faults, mining will be conducted as several small adjacent mines accessed through adits from large arroyos cutting through the mine area. Up to four seams may be mined in some areas with a maximum overburden depth of about 250 m. The ore zone is relatively weak and plastic, subject to extensive creep over time. The mine workings will pass through areas of historical shortwall mining panels where the ground has flowed into old entries and gob areas, and then reconsolidated. A small test mine was developed to evaluate mechanical cutting performance, roof-bolt anchorage capacities, roof and pillar stability and caving behavior. In-mine measurements were combined with two- and three-dimensional FLAC models to evaluate alternative development and production pillar designs. The paper will discuss the various factors influencing ground stability at the El Boleo project and the strategies employed in developing a suitable ground control design.

Jan 1, 2009

By Syd S. Peng

In the past few years, the numbers of underground coal mines in this country using longwa11 mining method have been dramatically increased. In the latest count there are approximately 90 10ngwa11 faces amounting roughly 8% of the total underground production. Meanwhile, shortwall mining adapting longwa11 powered supports to 'coal mining and handling systems in room and pillar mining is also gaining importance in the Appalachian coal field. Although there are only 7 operating shortwall faces so far, indications are that it will be increasing steadily. Modern longwall faces are highly mechanized and productive. One of these key elements that contribute to the success of modern longwall mining is self-advanced powered supports. There are several types of powered supports. Frame type is two sets of one to four hydraulic legs supporting beam-type roof canopy and floor base. However, chock type is more popular and connected to broad roof and base structure. Shield supports were introduced recently but proved to be highly successful (1). A shield support consists of two hydraulic jacks mounted between a base plate and a gob shield. The base plate is hinged to gob shield which is in turn hinged to roof canopy.

Jan 1, 1977

By Y. A. Attia

A study was performed on selective flocculation and dispersion for ultrafine coal cleaning. A totally hydrophobic polymer, FR-7A, was employed as the selective flocculent for coal, sodium metaphosphate (SMP) as the general dispersant for shale and a synthetic polymeric product, polyacrylic acid-xanthate (PAAX), as the selective dispersant for pyrite. In the adsorption tests, nephelometry and spectrophotometry were employed for determining the concentration of FR-7A and PAAX in the solutions respectively. The adsorption tests indicated that: a) FR-7A has a higher affinity toward coal and pyrite than that for shale; and b) PAAX has a much higher affinity toward pyrite than toward coal and shale. In the selective flocculation tests, the ash-forming minerals can be efficiently rejected using sedimentation as the separation method. However, due to their relatively high specific gravity, pyrite particles co-settle with the coal flocs. To reject fine pyrite, a froth flotation was used for floc separation. The one-step flocculation-flotation process could reject more than 70% of each of the pyritic sulfur and ash minerals, while recovering more than 85% of the coal.

Jan 1, 1990

By K. Norris

The Amax Gold Guanaco mine is located in the Atacama Desert, approximately 260 km southeast of Antofagasta, Chile. The 6,000 tpd leach operation produces approximately 90,000 oz of gold, and 360,000 oz of silver per year. Production began in 1987, and the operation has been managed by Amax Gold since 1992. The mine has been plagued in the past by high operating costs and low production. Several significant changes have been made to the operations which have resulted in lower costs and higher operating efficiencies. A review of these changes is presented herein.

Jan 1, 1997

By F. N. Earll

4.1 – DEFINITIONS 4.1.1-MINERALS, ROCKS, ORES AND NONMETALLIC MINERALS F. N. EARLL A mineral is a naturally occurring inorganic element or compound. Most minerals are distinctly crystalline in habit, and many commonly occur in well-formed crystals or crystalline aggregates, but a few species are characteristically amorphous or noncrystalline. Nearly 2,000 mineral species are now recognized but, perhaps fortun¬ately, a rather large proportion are rarely encountered. Even so, the application of modern mineral-detection and identification techniques reveals the presence of surprising numbers of mineral species, even in deposits of outwardly simple mineralogy. A rock is an aggregate of grains or crystals of one or more minerals. Some rocks are essentially monomineralic. Thus, limestone consists largely of the mineral calcite, and many sandstones are dominantly quartz. Most rock varieties, however, contain a number of mineral species, and their classification or identification depends upon the minerals present, their relative abundance, and such factors as rock tex¬ture and origin. Ore is defined as an accumulation or deposit of one or more minerals that can be exploited at a profit. The profit criterion commonly is taken somewhat liberally, however, for, although always present, the specific mineral content that constitutes a viable product is transitory. The term ore, usually, but no longer consistently, is restricted to the description of mineral deposits that are of value for their metal content. Nonmetallic deposits, although similar to metallic ores in many respects, generally are valued for the minerals or compounds present, as with rock salt (halite), rather than for individual contained elements, though such minerals as elemental sulfur are of much value. 4.1.2-ROCK TYPES F. N. EARLL Rocks arc grouped tinder three broad headings: (1) igneous rocks formed by the crystallization of magma; (2) sedimentary rocks formed by surface processes of weathering and deposition; and (3) metamorphic rocks, which may have been derived from either of the foregoing, but have undergone important physical and/or chemical changes through the application of heat or pressure, or both. The three groups can he further subdivided for convenient reference. Thus, igneous rocks are described as being abyssal or plutonic if formed at great depth, hypabyssal if formed at intermediate depth, and extrusive or effusive if formed at or on the earth's surface. The sedimentary rock group is similarly subdivided into clastic sediments and chemical precipitates. The clastic sediments form by deposition of preexisting minerals that were released from their place of origin by weathering and were transported to their point of deposition as discrete grains

Jan 1, 1973

By T. J. Joiner

A critical demand exists to develop new mineral resources, and the need for exploration techniques to supplement costly test drilling is becoming; more acute. In the past few years more industries have begun experimenting with geophysical methods to locate and define mineral deposits and delineate reserves. The new techniques have proven profitable in many instances. As a part of a broad long range program to study the mineral resources of Alabama, and in response to requests from land owners and mining companies, the Geological Survey of Alabama is investi¬gating the occurrence of bauxite and kaolin deposits in the Eufeula area. This project is supported by special funds appropriated for this purpose by the Alabama Legislature.

Jan 1, 1966

By J. B. Knapp, J. W. G. Betts, Scott L. Burreill, J. H. Bassarear, E. A. Lowe, W. J. N. Davis, John L. Bolles, Gaylord P. Dopson, William H. Keener, N. S. L. Steenkamp

This chapter contains moderately detailed descriptions of some typical and well known mills that treat predominantly sulfide copper ores, some containing secondary values in gold, silver, and molybdenum. The descriptions are general in nature, because most of the specific data will be found in tabulations elsewhere in this section, covering a large number of mills in such matters as flotation reagents, crushing and grinding equipment and steel consumption, thickener and filter operating data, power consumption, and many others, in a manner that the reader will find convenient and comprehensive for reference and comparison. On the other hand, the plant descriptions selected for this chapter emphasize the kind of information that cannot be readily tabulated.

Jan 1, 1985

By Harry H. Peek

Artesian pressures of unusual magnitude occur in the deeper aquifer units beneath a considerable part of southeastern North Carolina and extend into South Carolina. The high pressures were first observed in 1968 in wells near Wilmington that were drilled to "basement" rock and which were screened between depths of about 260 to 300 m (meters). The pressure was recognized by Peek and Heath1 as an anomalous geo-pressure and unrelated to recharge conditions in the region. Since 1973, much new information has been obtained on hydro-geologic conditions in the area and a preliminary report on the deep artesian pressures was published in 1975.2 Most of the basic information has been obtained from groundwater research stations constructed by the Groundwater Section of the North Carolina Department of Natural and Economic Resources as a part of Ground-water studies in the Coastal Plain Region. These stations consist of an exploratory well drilled to basement rock with wells completed in each principal aquifer unit to provide data on aquifer characterestics, water levels and water quality.

Jan 1, 1977

By K. Lapakko

Kinetic tests results are influenced by methodological variables, including test duration and mine waste particle size. Some samples tested produced neutral drainage in kinetic tests for more than two years prior to drainage acidification. The potential for long "lag times" can be assessed based on the mine waste mineralogy. The lag time duration can be estimated using this mineralogy in conjunction with dissolution rates observed in the kinetic tests. The influence of particle size on the drainage quality is dependent on the variation of the availability of acid-producing and acid-neutralizing minerals with particle size.

Jan 1, 1998

By C. W. Grate

Cooperative Education is by no means a new idea. The first such program was instituted at the University of Cincinnati in 1906 by the late Dean Herman Schneider with twenty-seven engineering students participating. Today, more than fifty years later, there are in excess of one hundred institutions' with some such program in which thousands of students, are participating in the fields of Liberal Arts, Engineering, and Business Administration. At the same time, according to a conclusion reached during a study of work-study college programs, copyrighted in 1961 by Thomas Alva Edison Foundation, and from which we quote; "We were amazed at the lack of-information about cooperative education among school and college staffs and students, among parents and employers, and on the part of the public generally."

Jan 1, 1963

By V. Gall

The three-dimensional finite element technique combined with the progressive failure approach was utilized to simulate stress distributions in a mine section which occur in response to a longwall mining operation. Due to the availability of the Cray supercomputer, a large-scale three-dimensional finite element model was developed for the analysis. The Hoek-Brown failure criterion, which describes a realistic behavior of rock masses, was used for the simulation of progressive failure. A comparison of calculated and monitored stresses in the mine has shown that the model gives a good representation of stresses in the mine structure.

Jan 1, 1990

By Bryson D. Trexler

Slope stability in open pit mines is governed by rock structure, rock quality, ground water conditions, blasting, pit geometry and excavation method. Of these factors, the control of ground water pressures often represents the primary tool to improve slope stability. Production equipment has recently been used to stabilize two slide areas by dewatering using blasthole drills for vertical holes and secondary drills for horizontal holes. This paper describes both of these dewatering programs and contrasts an earlier slope stabilization program that employed a subcontracted horizontal drill.

Jan 1, 1983

By S. P. Singh

Drifts are the nerve centre of underground mining. They provide essential communications between primary openings and production areas. In view of their strategic importance in the overall safety, economy and productivity of mines, an empirical approach for blast design during drifting has been proposed in this paper. The approach was developed with the objective of minimum blast damage and provides computerized blasthole patterns for drifting operations. The drift blasting practices and problems in Canadian mines have also been reviewed in this paper.

Jan 1, 1991