Search Documents

By C. J. Im

As market conditions become more competitive, U.S. coal producers are faced with the increasing need to find methods of lowering production costs in their operations. One area worthy of investigation is the additional recovery of fine coal that is normally discarded in the preparation plant waste stream. United Coal Company is currently assessing the capability of the Deister Flotaire, a new application of a column flotation cell, to recover additional, saleable coal from preparation plant waste. This paper presents the technical data obtained to date. Work with a 0.76 m (30 inch) diameter cell installed in a plant shows considerable coal recovery is possible from a nominal 0.595 run (28 mesh) X 0 refuse stream.

Jan 1, 1986

By M. G. Schulz

Mining of molybdenum at Questa, New Mexico has been accomplished by block cave methods since August, 1983. As caving progresses, a periodic geologic evaluation is made of the rock-types present in finger raises on the Grizzly Level of the mine. The production maturity of the cave can be monitored by relating this data to geologic cross-sections through the ore body. The draw point mapping program is a simple and effective tool that is used in making draw control decisions at Questa.

Jan 1, 1985

By Thomas B. Faddies

The Trixie mine is located in the East Mining District. Since production began in 1970 over 450 000 tonnes of ore grading 239 grams of silver, 6.9 grams of gold, and 1.2% Cu have been mined from veins in Cambrian Tintic Quartzite. Detailed geologic mapping and extensive sampling are essential for compiling the data base required for efficiently developing and mining known reserves as well as planning exploration and development work. Although the basic techniques used by the geology group at the Trixie were developed many years ago, the reduced activity in underground precious metal mining in the U.S. have made these techniques less familiar to many presently active geologists. The increased activity in precious metals search and exploration again offer cause for the application of these techniques as a prerequisite to efficient exploration, development and production.

Jan 1, 1983

By A. A. Densmore

Telluric Current is that portion of the electric field observed at the surface of the earth which is of an alternating nature, and which is related to solar activity and events in the ionosphere. The primary electromotance which drives the telluric current is the result of the induction process associated with time variations in the earth's magnetic field. The relationship between the electric and magnetic components of this electromagnetic field depend upon the conductor. For our purposes, we are dealing with frequencies f in the range

Jan 1, 1972

Direct force measurements were conducted using an atomic force microscope (AFM) to study the mechanism of copper-activation of sphalerite. The force measurements were conducted between a sphalerite plate and a hydrophobic glass sphere in xanthate solutions of various pHs. The glass sphere may represent the hydrophobic air bubbles interacting with minerals during flotation. The force measurements conducted with unactivated sphalerite in 10') M KEX solutions did not show the presence of hydrophobic force. On the other hand, the results obtained with copper-activated sphalerite at pH 9.2 and 4.6 showed strong hydrophobic forces. However, the results obtained at pH 6.8 showed no evidence of hydrophobic force, which provides an explanation for the difficulty in floating sphalerite at neutral pH.

Jan 1, 1998

By Robert P. Bell, John T. Waggoner

The Metropolitan Water District of Southern California is designing new outlet facilities for Lake Mathews, including a junction shaft, connecting tunnels, and an ear-shore outlet tower. Since Lake Mathews must remain operational during construction, groundwater inflow potential is a concern. This paper describes the challenges and methods used to investigate rock mass and groundwater conditions at an operational reservoir, where offshore and onshore geotechnical exploration was performed. Several investigative and analytical methods were used to characterize rock mass and groundwater conditions, including rock coring, downhole geophysical and video surveys, hydraulic conductivity testing, automated groundwater level monitoring, and laboratory testing.

Jan 1, 1999

By C. T. Aimone-Martin

Time-domain reflectometry (TDR) laboratory experiments have been conducted using cylindrical salt cores from the Waste Isolation Pilot Project (WIPP). TDR has been used as an instrumentation technique to quantify the type and magnitude of rock mass deformation. Laboratory shear and tensile tests were conducted to calibrate measured deformation versus changes in reflected waveforms. Coaxial cables grouted within rock cores were crimped to produce localized reference defects. The evaluation of waveform characteristics produced during rock deformation experiments shows a good correlation of cable response to both shear and extension of the salt

Jan 1, 1994

By Thomas F. Torries

It does not take sophisticated economic analysis to determine the current status of nickel production and demand (Figure 1). One only needs a quick glance at the balance sheets of the major nickel producers to learn that prices are down and profits are supressed to the point where they are major losses. Operations have been closed, and those remaining in production have reduced output. What Is now of interest Is, when will the nickel market improve and to what degree? The purpose of this paper is to attempt to answer these questions. This will be done by the normal method of projecting nickel demand, chosing a production scenario, and analyzing the results.

Jan 1, 1982

By J. R. Dillon

Today more than ever, there is an increased demand for higher plant production capacities and efficiencies to offset the increasing costs for labor and materials. Plants involved in processing large volumes of bulk materials are particularly interested in more efficient material handling systems to (1) reduce labor and maintenance costs, (2) improve blending of non-uniform raw material feed to processing facilities, (3) improve blending of finished bulk materials from storage. DragScraper systems are being used effectively for handling a variety of bulk materials in both indoor and outdoor storage. Materials being handled include ores, chemicals, coke, clay, and stone, to name a few. Handling capacities these machines can provide vary from a few tons to over 1500 tons per hour. The basic components of a DragScraper machine consist of a bottomless Crescent scraper, a two or three-drum DragScraper hoist assembly including gas, diesel, or electric power unit, operating cables, guide blocks, and either fixed or mobile head and tail structures. They are presently available in sizes through 15 cubic yards, for operating spans up to 1000 feet.

Jan 1, 1969

By S. S. Sephton

The La Perla Mine, owned by Altos Hornos de Mexico, S.A., is located approximately 100 miles east of the City of Chihuahua in the State of Chihuahua, Mexico. The mine began operations in 1958. Existing ore beneficiating facilities, consisting of heavy media and jig plants, upgrade the ore prior to shipment by rail to the Altos Hornos steelmaking complex in Monclova. Sizable reserves of two distinct ore types, which were not amenable to treatment in the existing beneficiating plant, or usable in the blast furnaces, have been mined and stockpiled in order to uncover the treatable ores. One of these ore types has been labeled "Diseminado" ore, and is low grade containing approximately 42% Fe with sulphurs ranging from 1 to 2%. The other ore type has been labeled "Pulverulento" ore, and is high grade containing approximately 65% Fe and 0.1% S, but at 80% minus 325 mesh, is too fine grained for efficient sintering. Late in 1968, Arthur G. McKee & Company became involved with the problem of improving the above ores for their efficient and economical use in Altos Hornos' blast furnaces. Early in 1969 representative samples of Diseminado ore were obtained for laboratory bench-scale testing at the University of Minnesota, Mineral Resources Research Center. Concentration tests incorporating magnetic roasting, wet magnetic separation, high intensity separation, high tension magnetic separation, anionic flotation of apatite, cationic flotation of silica and oleic acid flotation of iron were performed. Laboratory testing was concurrently carried on at La Perla Laboratory, which resulted in plans to construct a 10 TPD pilot plant. The pilot plant was operational in September, 1969. Analyzing laboratory results as well as pilot plant results, Altos Hornos and Arthur G. McKee & Company metallurgists agreed that the most promising flowsheet for the low grade Diseminado ores entailed wet magnetic cobbing, desliming, and oleic acid flotation of the non-magnetic fraction. A combined concentrate of

Jan 1, 1972

By L. J. Tucker

The magnetite orebody at Pea Ridge strikes NE-SH and dips at about 800 to the SE. The ore is high grade magnetite with a strike length of over 600-m and a maximum width of over 180-m on some of the levels. The shape and the mineral content of the iron orebody have been fairly consistent so far. The iron ore and surrounding basement rocks are Precambrian in age. These rocks are usually very competent, about 400-m of sediments lie over the ore.

Jan 1, 1991

By S. Constantinescu

The alloys mainly used for short (or segmented) chip material cutting (cast iron, porcelain, etc) are alloys of the WC-Co type; in some cases with small additions of other carbons. The same alloys but of different granulometric classes are also used for pieces exposed to wear (wire drawing, moulds) The higher performance of the WC-Co alloys in chip machining applications is accounted for by their very good heat conductivity, which is 2-3 times higher than that of fast steels. The hard-alloys producers can resort to a wide range of possibilities to achieve variation of properties of a WC-Co composition and thus they can adapt their products to the particular type of tools they may choose to manufacture. The present metallography technique allows for a correct identification and evaluation of hard sintered carbons structures. The metallography approach is an indispensable method of investigation and control in the industry.

Jan 1, 2008

By J. P. Matoney

In recent years, the diminishing supply of natural gas has led energy suppliers and consumers to consider making synthetic natural gas from coal. A number of processes have been devised to produce gas from coal; many of these have been operated at the pilot stage and some have been operated commercially. Each process has specific coal feed stock requirements with respect to size consist and moisture content. The purpose of this presentation is to compare the estimated costs for coal handling, live storage, size reduction and drying facilities that would be required for delivery of coal feedstock to different gasification processes.

Jan 1, 1977

By Jacques B. Wertz

It is well known that the major fractures and lineaments presently recorded in Western North America are preferentially oriented along a general northwest direction (Figure 1). There are other features, however, more subtle, more elusive as a rule and which can only be inferred, occurring at right angle to this broad NW direction. It is intended a) to examine some of these NE or transverse trends, b) to compare these regional NE breaks to similar ones that transversally cut through the eastern part of the European Tethys, more specifically in Iran and Turkey, and c) to study their potential relationship to mineralization in both areas.

Jan 1, 1973

By William P. Shell

An important part of process control engineering is the implementation of the basic control system design through commissioning to routine operation. This is a period when basic concepts can be reviewed and improvements either implemented or recorded for application in future systems. The experience of commissioning the process control systems in the Homer City coal cleaning plant are described and discussed. The current level of operating control performance in individual sections and the overall system are also reported and discussed.

Jan 1, 1983

By H. R. Quina

Phosphate is one of the most important minerals in our world today. It contains the life-giving element of phosphorus, which is essential to the growth of every living cell in plant, animal, and man. This vital mineral is found in twenty-three states of the United States; however, for more than 70 years, Florida has led the nation in phosphate-production and now produces 70% of the requirements of this country. Since the early 1880% when rich phosphate deposits were accidentally discovered in a river-bed in Central Florida, the industry has developed into a multi-million-dollar operation. Phosphate mining began in Florida in 1887 with very crude methods and equipment. The original process was necessarily slow and tedious, resulting in total production of 3000 tons in 1888. Progress was made in improved mining operations, and by 1894. Florida had grabbed the lead as the nation?s largest phosphate-producing area, and is still in the top position.

Jan 1, 1962

By S. T. Hall

The authors have previously described a method of enhancing the magnetic susceptibility of pyrite by a mild alkaline oxidative pressure leach (Hall et al, 1985). This finding was successfully applied to enhance the magnetic desulfurization of an Eastern Canadian coal (Hall and Finch, 1984). This paper reports on enhancement of the magnetic susceptibilities of iron-containing sulfides (arsenopyrite, chalcopyrite and marcasite) upon similar treatment. It also explores the application of this pretreatment in the magnetic separation of fine sulfides from oxides and other sulfide minerals. In the latter case galvanic interference effects have a serious impact on the potential use of this method.

Jan 1, 1985

By J. L. Young

The McLaughlin Mill started operating in January, 1985. For the first eighteen (18) months start-up, initial operation, and circuit debottlenecking have been done. The mill was designed to recover gold from a refractory ore requiring acid autoclaving pretreatment. This paper discusses the problem associated with bringing this complex hydro-metallurgical plant to consistently achieve design tonnages. Also, briefly described are the mill flowsheet, training program, permitting, and process and project development.

Jan 1, 1987

By Richard Klimpel

1. Introduction Laboratory and industrial grinding tests have shown that the process of size reduction can be significantly influenced by chemicals added to the powder or slurry being ground. The terms grinding aid or grinding additive refers to a substance which when mixed into the mill contents causes an increase in the rate of size reduction. The increased rate can be used to grind a higher feed rate to the desired product size or it can be used to produce a finer product size at a fixed feed rate. Whether the use of a grinding aid is justified in any given situation depends on the cost of the substance versus the improvement of output or product quality obtained with its use. Obviously, an expensive chemical must be effective in very small concentrations if it is to be economically justifiable; the cost criteria is calculated on the basis of the cost of the grinding additive per ton of material ground. Although there is direct experimental verification of the advantageous effect of grinding additives, no sound scientific explanation has yet been offered which explains or predicts the general behavior of additives. Rose and Sullivan have summarized most of the work undertaken prior to 1950 and Hartley, Prisbrey, and Wick have recently prepared an updated synopsis of the grinding additive literature. Many of the studies reported consist of subjecting materials with simple geometric shapes to some type of hardness or controlled single fracture test. On the other hand, a number of the studies were carried out on operating industrial scale mills, with little control or precise monitoring of the effect of the additives.

Jan 1, 1977

By D. W. Park

Underground room-and-pillar mining operations in the Warrior Coal Field in Alabama frequently suffer instability due to soft floor and thinly-laminated immediate roof. The investigation covered by this paper concerns a mine that was experiencing ground-control problems with weak floor conditions. Four hundred ft above the presently producing seam, another seam has been mined out. Several roof falls occurred locally, and as much as two ft of floor heaves have been experienced. The paper presents the results of comprehensive analysis conducted on floor heave, roof sagging, and the influence of the mined-out seam using instrumentation and numerical analysis.

Jan 1, 1991