Search Documents

By A. K. Sinha

Despite the tremendous efforts and costs incurred by the industry and regulatory agencies to prevent premature roof failures in underground mines, roof falls continue to occur frequently due to the very unpredictable geological conditions and dynamic nature of mining operations. In fact, roof falls continue to be the largest contributor to coal mine fatalities. The failure of a mine roof generally occurs following a prolonged, gradual degradation in its physical conditions. An electronic mine roof monitoring system has been developed and tested in operating mining sections. It monitors mine roof degradation on a continuous basis. The field test results are presented and discussed.

Jan 1, 1987

By Alex Lowson, Dan Tempelis

The Riverside Badlands Tunnel segment of the Metropolitan Water District of Southern California’s Inland Feeder Project, was lined with a segmented concrete primary lining and a welded steel final lining with the annulus filled with Low-Density Cellular Concrete (really a grout). The paper describes a numerical modeling technique that was developed to determine safe grout placement procedures to avoid pipe flotation, and shows the relationship between flotation and the rheology of the liquid grout. Design details of the steel liners are often not well suited to grout placement, and recommendations are given on how to improve this.

Jan 1, 2003

By George R. Huebner

The White Pine Copper Company, subsidiary of Copper Range Company, is located in the Upper Peninsula of Michigan. The offices, plant, and mine are six miles south of Lake Superior in Ontonagon County. Employing 1700 people, White Pine is the largest single industry in the Upper Peninsula. 970 underground employees produce 16, 700, tons of ore daily. From this tonnage 363,400 pounds of refined Lake Copper are produced in various shapes as specified by the customer. The following paper explains the geology of the ore body and briefly outlines present mining methods. It enumerates the reasons for considering longwall mining of a hardrock* ore body and the preliminary investigations leading to the decision to undertake the initial test panel. Selection of the initial test panel location is covered in detail. Equipment choice and reasons for that choice are described as well as selection and training of personnel.

Jan 1, 1964

By T. R. A. Davey, J. W. Sherman, B. J. DiSanto, G. Bjorling, G. S. Stacey, J. T. Cullom, R. L. Bird, S. E. Woods, J. C. Blair, Jorma Honkasalo

Most pyrometallurgical processes take place at high temperature with rapid chemical reactions when the elements and compounds are usually liquid or gaseous. Smelting. The classical method of obtaining a metal from its ore or concentrate is to smelt it in a furnace. The initial letter "s" of this word implies that, in addition to the physical process of melting, a chemical change also occurs. This is usually the reduction of metal oxide to metal by carbon or through a series of processes involving oxidation and reduction. Since solid-solid contact would not be sufficient to give a high rate of reaction, most smelting reactions occur by medium of two reactions involving solid-gaseous contact: where M represents a metal. The commonly preferred unit for carrying out these reactions is the blast furnace,1 which is a vertical shaft of refractory brick or water-cooled steel in which lumps of metal oxide and coke are fed at the top, and an air-blast is injected through tuyeres (water-cooled pipes) in the bottom. Molten metal is withdrawn from a pool at the bottom of the furnace, while N2, CO, and CO2 gases leave the top of the furnace, carrying some fine dust or fume with them, which

Jan 1, 1985

By H. P. Ehrlinger

The Negociacion Minera Santa Maria De La Paz mining operations are located at La Paz (some eight miles West of Matehuala), State of San Luis Potosi, Mexico. These operations consist of a single copper-silver property, called the Dolores mine and a number of silver-low base metal properties. The ores from these several mines are transported by rail, or truck, to the central milling unit. The milling unit has two separate sections to treat the two types of ore. The ores from the several silver-base metal mines are mixed at the mill as they arrive. Up to the present time the silver-base metal ores have been milled to produce a bulk concentrate which carries valued in gold, silver, copper, lead, zinc, cadmium and considerable arsenic. In such concentration the zinc and cadmium values are lost to the operations in their liquidations as they are shipped as lead concentrates. Since these ores have exceptional quantities of arsenic which is concentrated in the milling process, these bulk concentrates have to be sent to a smelter for pre-smelting operations to remove the arsenic.

Jan 1, 1964

By Thomas F. Evans

Niagara Mohawk, like other northern coal users, has long experienced increased costs during winter months as a consequence of handling frozen coal. These costs include operating labor, maintenance labor and materials, equipment rental, fuel for thawing, demurrage, carrying costs for excess coal inventory and substitution of higher cost electrical generation for lost production capacity. In the winter of 1978-79, limited trials of several coal freeze conditioning agents were made to determine whether these would provide a cost-effective means of reducing the problems of handling frozen coal. Since these trials were generally effective, the Coal Purchasing Department arranged that all rail coal received during the 1979-80 winter from early December to mid March would be treated at the mines during loading. Inasmuch as the treatment costs are themselves appreciable and our various coal suppliers made a variety of choices of chemical supplier and equipment for application, an attempt was made to evaluate the unloading performance of each train received at the two generating stations which use coal as an aid in the future optimization of the use of freeze conditioning agents. These stations also receive coal by truck but this coal is not treated because of the short hauling time. The C.R. Huntley Station in Tonawanda, NY has a capacity of 800MW and burns about 5000 tons of coal per day during the winter months. The coal is primarily from central and western Pennsylvania but one source in southern Kentucky is also used regularly. Most of the Pennsylvania coal is washed and the fines are thermally dried. The coal is delivered in unit trains made up of mixed cars of 60, 75, and 90 ton capacity. Time between loading and arrival at the station averaged five days and ranged from three to eleven during the 1979-80 winter season.

Jan 1, 1980

By Travis S. Wellman, Jon C. Volkwein

The Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low profile mining machine. Tests were conducted in a full scale model mine using a Joy 12 CM 10-AA continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters included: mining position, depth of cut, brattice setback and combinations of scrubber, directional sprays or symmetrical sprays. Results indicated that either directional or symmetrical water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 6 m (20-ft) blowing curtain without sprays. No FVE values were less than the standard 6 m (20-ft) blowing results.

Jan 1, 1989

By P. K. Chatterjee

Computer aided design and inter active graphics have been well established in the electronics, automotive and mechanical engineering industries. The use of such aids in underground mine design and planning, however, has been noticeably absent. The large expense involved in the research and development of CAD and graphics systems and their highly specialized techniques have rendered investment in these areas difficult to justify. Optimum mine planning involves an interactive procedure of evaluation of several alternative plans. Generally the development of each mine plan of a given operation can take many man-months. This time constraint on planning precludes any comparative analysis and evaluation of alternatives, thereby introducing the possibility of unrealized gains. This paper outlines the development of a computer aided mine design program utilizing interactive graphics for the design, simulation and scheduling of underground coal mines. The program developed examines exploratory borehole information and produces a structured database of the sampled data. This database is utilized to generate seam sections and different mine layouts. A simulation of mine extraction and production levels and a schedule of proposed alternatives are then performed.

Jan 1, 1984

By D. R. Buist

The Taharoa plant of New Zealand Steel Mining Limited extracts a 57% Fe titano-magnetite concentrate from a large mineral sand deposit 90 miles south of Auckland on the west coast of New Zealand's North Island. The plant consists of an 18-inch suction cutter dredge which feeds a 750 TPH floating separation plant. An initial gravity/ size separation is obtained using cone concentrators. Finished concentrate is produced by a combination of conventional drum magnetic separators and top fed wet Mortsell magnetic separators. Concentrate is stockpiled by cyclone, and reclaimed by a bull- dozer and tunnel system. Repulped concentrate is pumped by sub- marine pipeline to slurry tankers anchored at a single buoy one mile offshore. Current concentrate production rate is in excess of one million metric tons per year.

Jan 1, 1973

By A. E. Isaacson

The U.S. Bureau of Mines is investigating a systems approach to metals recovery from leach liquors produced by in situ leach mining techniques. A successful in situ leaching process requires a thorough under-standing of the complex interrelationships that exist between leaching chemistry and metals recovery. Laboratory research is addressing these interrelationships in the solution mining of a copper oxide deposit. Laboratory tests have been conducted to gather baseline data related to the design and operation of continuous leaching-solvent extraction-electrowinning circuits. This paper addresses the findings of the baseline studies. Specific results include the characterization of simulated in situ leach liquors produced by leaching chrysocolla and chrysocolla-atacamite-bearing copper ores. Metal recovery procedures, utilizing four commercial solvent extraction reagents, are also characterized, and potentially troublesome leach liquor contaminants that may complicate waste management procedures are identified.

Jan 1, 1990

By Marion A. Goudie

The Devonian salt basin, which contains the Saskatchewan Potash deposits, extends from just east of the foothills in Alberta, north as far as the Peace River area, across Saskatchewan and into Manitoba as far east as Range 10 west of the First Meridian and south into Montana and North Dakota. The basin is closed everywhere except to the northwest. The known potash deposits are confined almost entirely to the Province of Saskatchewan, with the exception of a small area in western Manitoba bordering the Saskatchewan boundary. The following discussion will concern only the Saskatchewan part of the basin. The evaporite series in the basin is defined as the Prairie Evaporite Formation of the Elk Point Group, of Middle Devonian age. Recent work done by potassium-argon dating methods has indicated an Upper Middle Devonian (Givetian) age of from 265 to 347 million years for the potash. The Elk Point Group consists in ascending order of the Ashern, Winnipegosis and Prairie Evaporite Formations. The Ashern formation, sometimes called the Third Red Bed, consists of dolomitic shales or shaly dolomites. The Winnipegosis is a reef type dolomite, usually with good porosity, and in many cases oil-staining, although to date no production has been obtained. The Prairie Evaporite formation consists of anhydrite overlain by halite and finally, in Saskatchewan, by the potash beds. In almost all wells which have been cored for potash the lowest potash bed is underlain by one or two bands of anhydrtte, which are used as marker horizons. Cores from a few wells which cored to the bottom of the salt series have shown flecks of potash throughout the halite.

Jan 1, 1959

By Jack G. Pippenger

The Coteau Properties Co.'s Freedom Mine is a surface lignite mine that uses large draglines, trucks and shovels, tractor-scrapers and bulldozers to uncover a single coal seam. In 1989, a work order system was instituted to record data by equipment type, cost, productivity and distance. The system was also used to provide historical information to plan the most efficient and economic use of each equipment type in the mining operation. The Coteau Properties Co. is a wholly owned subsidiary of The North American Coal Corp. The company was formed in 1972 to supply lignite from its Beulah-Hazen coal reserve to a coal gasification project and an electrical generating facility located near Beulah, ND. The reserve consists of a single coal seam between 3 and 7 m (10 to 23 ft) thick. The overburden above the coal is predominately glacial tills and clays and ranges from 6 m (20 ft) to more than 60 m (200 ft) thick.

Jan 1, 1994

By Ronald L. Haxby

This report presents a refractive seismic technique for evaluating the strength of rock within an open pit bench. A concept of correlating rock strength and seismic velocity is discussed and a method of predicting the degree of fragmentation of a pit bench is introduced, Figure 1 shows the area of interests [ ] Most of the work was performed while completing graduate studies at the University of Arizona.

Jan 1, 1967

By C. Sun

Due to unfavorable geological condition, excessive deformation of mine drifts occurred in a large underground copper and nickel mine. In searching for a solution, a comprehensive underground monitoring program was implemented and the opening convergence and the surrounding rock deformation were monitored. A large number of field data were collected and thoroughly analyzed. The convergence and deformation as function of time and depth were determined and a rock stability index was proposed. Based on the deformation-time and deformation-depth relations, critical deformation times and locations were identified and defined as characteristic values to be used for mine opening and support designs. The characteristic values are critical in the application of two-step supporting system, and the determination of support parameters. The application of the method developed in this study has demonstrated that this practical approach in support design and installation is effective. With the two-step supporting system, a long-term drift stability can be achieved in the mine.

Jan 1, 1998

By R. A. Wyman

What unusual features are there about finding, winning, and using the industrial minerals of Canada which may be of interest and yet not widely known. Have you, for example, ever wondered where the raw material for those distinctive greenish grey statuettes, so readily recognizable as Eskimo carvings, comes from? Although stone suitable for carving is obtained at several northern locations, in recent years the Federal government, the Quebec government, and one or two private companies have shipped supplies of various rock types from other sources to central distribution points in the Canadian north for the express purpose of providing Eskimo artists with raw materials for carving. Canada is well endowed with industrial minerals, the extent and variety of which may be observed by a perusal of Table 1. In this table, materials currently produced are shown in the left-hand column; materials which are bordering upon economic viability are listed in the middle column; and materials which have been found in Canada in possible exploitable quantity, but for which [ ]

Jan 1, 1970

By Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides: chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 1000 to 150°C. The rate of dissolution of chalcopyrite becomes so rapid under these conditions that the rate of recovery is no longer limited by the rate of chalcopyrite dissolution, but by the degree of exposure and other factors. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, size of sulfide particles, and fraction of sulfide exposed to solution.

Jan 1, 1972

By James J. Scott

In 1910 the United States Bureau of Mines was created. It was the outgrowth of a social problem stemming from the fact that 25,000 men were killed in coal mining accidents for the period 1900-1910. Something had to be done and congress responded to the people's demands by creation of this new regulatory agency. At that time mine operators felt the new agency was too strict but nonetheless new rules were developed and enforced and results were obtained by the industry which reduced fatal accidents to less than 250 per year by 1970.*Social reaction by the general public brought about legislation which created the Federal Coal Mine Health and Safety Act of 1969 This legislation was a direct reaction to the Farmington Disaster. Operators and miners alike said "we cannot operate under this law. It is too strict, requirements are unrealistic, production will suffer, .there will not be any improvement in health and safety, etc." Consider the facts: 1. Health and safety have improved. The 1972 frequency and severity rate was the best ever for the bituminous coal mining industry, Figure 1. 2 .Production per manshift has dropped in underground coal mines. For example, in West Virginia from near 16 tons/m.s. in 1967 to nearly 11 tons/m.s. in 1971-72. However, not all of this loss can be attributable to the Act, but certainly some is. (2) The betterment of the safety of coal mining was a prime motivation behind the coal law and from that standpoint the law has been partially successful, but the loss in productivity has been a real burden to the mine operator. Everyone should recognize that the law says little in regard to production--it only relates to health and safety. Production is management's responsibility.

Jan 1, 1973

By K. Konialis

In the last twenty years, the mining industry has made marked efforts to improve its reputation in regard to its social performance. These efforts have been expressed in the 9th ICMM (International Council on Mining and Metals) principle as a commitment to contribute to the social, economic and institutional development of the local communities. Towards this goal, which has been increasingly highlighted because of its importance for sustainable development, a number of practices and methods have been developed. The international development literature describing these practices is full of so-called development buzzwords, such as stake-holder participation, empowerment, capacity building. This paper argues that none of these development catchwords are neutral, but contain assumptions based on a specific view of development. Since capacity building is a central task in development, the paper focuses on this concept and takes a critical look at the assumptions that underlie this concept and influence strategies employed by the mineral sector. It suggests that the notion of capacity building in some earlier approaches implies a set of asymmetric power relationships between developed and developing countries where capacity is transferred from the developed countries to the developing ones. The developing countries are seen as passive recipients while the experts, i.e. the developed countries through their mining companies ultimately control the capacity-building process. The paper also points out that the mainstream capacity development approach has been based on the assumption that local or indigenous communities are mainly made up of needs and capacity gaps. The goal of development projects should then be to address these needs, which are perceived and prioritized by the ?experts?. Critiques of this development model suggest that in order for the mining industry to embrace more successful and sustainable practices, it should rethink the notion of capacity building. It should move towards alternative approaches that see it as a two-way learning process which will serve to enhance not only the capacities of the communities, but also of the development practitioners and which will build on the strengths of the community, and move away from attitudes of superiority and practices of dependence.

Jan 1, 2007

By John D. Kalasky

Ventilation is necessary in coal mines to supply fresh air to the working faces for the health, safety, and comfort of the miners, and for the circulation of air to the extent that it will dilute, carry off, and render harmless the noxious or dangerous gases generated. Adequate ventilation depends upon good face control, as well as upon a well designed and properly controlled overall ventilation system. Generally, this includes fans, airways, overcasts, air locks, regulators, checks, and canvas or plastic stoppings near the working places to prevent short circuiting of air, and effective bleeders to maintain a continuous flow away from the working places along the pillar lines at all times and to prevent diffusion of methane back to the pillar line in case of temporary interruptions in ventilation. In the development of a new mine, or the virgin area of an old mine, the main headings should properly be considered a construction project, designed with, only the number of permanently supported (roof) headings required to conduct the necessary air volume to and from the major panels in which mining is conducted by room and pillar or longwall methods. Although subject to hazards from methane quite frequently and requiring constant and careful attention at all times, development of headings has some built in safeguards which make it a less difficult problem in control of methane than exists in pillaring.

Jan 1, 1973

By P. T. Luckie

Analysis of classifier performance independently of a closed grinding circuit configuration may result in a poor match-up between the grinding device and the classifying device. This paper examines the relationship between classifier and grinding device in dry grinding circuits by employing a semi-empirical methodology.

Jan 1, 1980