Search Documents

By Ting Ren, Jon Roberts, Zhongbei Li, Ming Qiao, Jianming Wu

Spontaneous heating of coal continues to present a health and safety hazard in underground coal mines. The influence of seam gas composition on gas flow dynamics and distribution characteristics in the active longwall goaf has not been studied in-depth, and corresponding effective proactive goaf inertization strategies for preventing potential spontaneous heating from occurring have limited investigation. To advance this knowledge, an 80-m-height goaf model was constructed and developed based on specific conditions of an Australian underground coal mine, and onsite gas monitoring data was collated to verify base model results, which allowed for various scenarios of seam gas composition to be simulated and investigated with confidence. This study involved modeling five different gas composition scenarios for the goaf atmosphere, namely, 100% CO2 (case 1), 80% CO2 and 20% CH4 (case 2), 50% CO2 and 50% CH4 (case 3), 20% CO2 and 80% CH4 (case 4), and 100% CH4 (case 5). Simulation results show that O2 is primarily distributed at the middle and upper part of the CO2- dominant goaf model, while it is mainly layered at the floor level of the CH4- dominant goaf model. N2 is superior to CO2 in the goaf inertization for the CO2- dominant goaf model, whereas CO2 performs better than N2 for the CH4- dominant goaf model. The optimal inert gas flowrates for case 1 to case 5 are 1.5, 1.75, 0.75, 0.5, and 1.0 m3/ s, and the oxidation zone area is reduced by 55.76%, 67.21%, 58.04%, 78.17%, and 81.82%, respectively. The simulation results allow for increased insight and understanding of the gas distribution patterns in the active goaf with different seam gas composition and the development of corresponding proactive goaf inertization practices, thus minimizing potential spontaneous-heating-related hazards and improving mining safety.

Sep 26, 2023

By Liming Yuan, Isaac Zlochower, RICHARD THOMAS, Thomas H. Dubaniewicz, Teresa Barone

Mining vehicle manufacturers are developing lithium-ion (Li-ion) battery electric vehicles as an alternative to diesel-powered vehicles. In gassy underground mines, explosion-proof (XP) enclosures are commonly used to enclose electrical ignition sources to prevent propagation of an internal methane (CH4) air explosion to a surrounding explosive atmosphere. Li-ion batteries can create pressurized explosions within sealed enclosures due to thermal runaway (TR). Researchers at the National Institute for Occupational Safety and Health (NIOSH) measured TR pressures of lithiumiron phosphate (LFP) cells as a function of free space within sealed enclosures and observed an inverse power relationship. A well-confined cell produced 294 bar (4260 psia) of pressure during a TR, far exceeding minimum pressure containment specifications for conventional XP enclosures. Results indicate that adding enough free space surrounding LFP cells can reduce TR pressures to levels below that expected for CH4-air ignitions. Measured TR temperatures were below the minimum autoignition temperature of CH4-air.

Nov 6, 2020

By Robert M. Valentine, Randall L. Lentell

Interpretive geotechnical investigations were performed for the construction of approximately 15,250 m (50,000 ft) of wastewater interceptor tunnels in Austin, Texas. Subsurface materials consist of claystone (or clay shale), siltstone, altered volcanic tuffs, chalk and limestone. Special conditions include multiple crossings of Onion Creek with cover ranging from about 1/2 to 3 m (2 to 10 ft.), and the potential for mixed-face conditions consisting of water-bearing gravels overlying clay shale or siltstone. The methods and results of the geotechnical investigations are discussed and the inferred construction conditions are compared to those encountered during tunneling. A suggested format is presented for interpretive geotechnical reports for underground construction projects.

Jan 1, 1985

By Randy Vranes

Sophisticated information technology, quality management systems and a commitment to the environment has allowed Solutia’s Soda Springs phosphate mine and elemental phosphorus plant to reduce operating costs, improve product quality and contribute to the sustainable development of Idaho’s industrial minerals. Soda Springs background The Soda Springs phosphate mine and plant is a joint venture between Monsanto and its operating partner, Solutia Inc. The operation is based in southeastern Idaho in the Western Phosphate Field. The plant is located about 275 km (170 miles) northeast of Salt Lake City, UT and about 4 km (2.5 miles) north of the town of Soda Springs.

Jan 1, 1999

By J. Wagner, P. Eger

Although lifetime estimates for sulfate reduction based on total substrate carbon typically range from 20 to 30 years, field and laboratory experiments showed that rates of sulfate reduction decreased over time as readily available organic material was consumed. When the rate of acid input exceeded the rate of sulfate reduction, alkalinity was removed from the substrate, pH decreased and metals increased. Output pH increased from 4 to over 6 after the system was shut down for several weeks and the rate of acid input was reduced. Successful long term treatment requires a design based on the input pH and the long-term organic decomposition rate.

Jan 1, 2001

By Dean Bray

During the past three years, a new rear-dumping dragline bucket technology has been patented, developed and tested at North Dakota coal mines. Field testing has shown that this new concept in dragline bucket technology can improve strip-mining efficiencies by reducing cycletimes and increasing dumping radius. This article details the process, participants and the results for the development of a rear-dumping dragline bucket. Participants in the process In November 1995, the board of directors of Dakota Coal authorized the execution of a field test and option agreement and a license agreement with the partnership of D.F. Schmidt, electrical/maintenance supervisor, and Bill Lengenfelder, president of Modern Industrial. The board also authorized entering into a dragline bucket field-testing agreement with the Falkirk Mining Co.

Jan 1, 1999

By Xiaolong Bi, Shaohua Luo, Longjiao Chang, Shiyuan Cao, Jianan Liu

The abstract discusses the extraction of silica from nickel laterite ore using a hydrothermal process with sodium hydroxide. The effects of reaction temperature, time, and NaOH-to-ore ratio on silica extraction were investigated. The optimal conditions were determined, achieving over 98% silica extraction. The mechanism involves the reaction of Si in lizardite and quartz with sodium hydroxide, forming sodium silicate solution. Other metals like Mg, Fe, and Ni are enriched in the residue.

Apr 21, 2022

By J. M. Ekenes

New approaches that increase hydrometallurgical recovery from refractory minerals in below-mill-cut-off-grade sulfide copper ore can add significant value, improve profitability and increase ore reserves. This paper describes the development and implementation of an engineered heap (EH) approach to leaching low-grade, chalcopyrite-bearing ore at Freeport-McMoRan?s mine in Morenci, Arizona. The technical evolution of the engineered heap concept is described together with the challenges and benefits following implementation.

Jan 1, 2012

By Jaidev Sankar

The dream of constructing the new Second Avenue Subway in New York has finally become reality as the first construction contract package is currently underway. This first contract requires the construction a TBM Launch Box in the middle of Second Avenue from which a Tunnel Boring Machine (TBM) will bore two tunnels south to 63rd Street. This paper will discuss the design of this contract and how construction has progressed including preparation, site constraints, utility construction and com-munity impacts while highlighting the challenges of working in an urban environment. It will also discuss moving forward on this major project outlining the remaining contract packages including their scope and status.

By G. Gaidajis, K. Angelakoglou

The development of a tool for assessing the environmental sustainability of mining facilities is described in this study. The tool is based on the analysis of basic components of the examined system, i.e., the quantities of the incoming materials and outgoing wastes, their hazardousness and scarcity, the utilization of water and energy resources, and the biodiversity. The developed tool provides both qualitative and quantitative assessment of the environmental performance of a mining facility in a broad time scales (past-present-future) and is easily applicable from non environmental experts. Moreover, relative software is developed to further support the application of the methodology. The implementation of the tool is expected to lead to an improved understanding of the environmental performance of a mining facility and more importantly identify the areas of significant environmental concern. However, based on feedback from industries, a number of shortcomings of the approach have been identified so far and are presented, indicating further actions for the advancement of the proposed tool.

Jan 1, 2011

By Wern-ping Chen, Jean Habimana, Jinyuan Liu, Mirza M. Rabbaig, Robert Barbour

To mitigate and control the combined sewer overflows from 17 outfalls in the City of Detroit, three outfalls in Dearborn Heights and eight outfalls in Redford Township, the Detroit Water and Sewerage Department has completed the preliminary design of a storage tunnel in 2005. In 2006, a final design has revised the alignments and the inside diameter (ID) of the tunnel. The revised tunnel system includes an 11.28-km(7-miles) 9.14-m (30-ft) ID tunnel, a 24.4-m (80-ft) ID pump station, two work shafts about 15.2-m (50-ft) ID each, and 14 drop shafts with various IDs. This paper discusses the latest development of this tunnel system.

Jan 1, 2007

By David R. Morrey

During the past 50 years, significant research has been performed in the ecology and physiology of plants that colonize soils containing elevated concentrations of heavy metals. Similar work has also been performed on plants that are able to survive acidic and saline environments. Efforts have focused on the ecological analysis of plant communities that occur over a range of metalliferous mining wastes. Investigations have been performed on the mechanisms that allow selected varieties of plant species to survive in normally phytotoxic environments and on the potential applications of metal-tolerant varieties of plant species. The purpose is the remediation and reclamation of mining wastes and soils that contain unusually high concentrations of so-called heavy metals. Characteristics of some mineral wastes Metalliferous mining wastes present special environmental restoration problems because of their toxicity. Potential toxicities are mostly caused by residual metals derived from weathering of low-grade ore or the waste products of mineral processing. In cases where pyrite forms a part of the mining waste, acid generation by oxidation may exacerbate the toxicity problem by promoting heavy-metal mobilization in aqueous solution.

Jan 1, 1995

By J. M. Somers

Methane is a powerful greenhouse gas and the principal component of natural gas. Coal seams often contain significant quantities of methane, and underground coal mines must ensure that methane released into the mine during coal extraction does not build to dangerous levels. This is accomplished in part through the use of large-volume ventilation systems that remove methane from the mine and release it to the atmosphere. Although the methane concentration exhausted is quite low (typically <1 percent), the volume of air that ventilation systems move is so great that they actually constitute the largest source of methane emissions from underground coal mines. Each year underground coal mines throughout the world emit more than 500 billion cubic feet of methane from their ventilation systems. An air pollution control technology, thermal oxidation using a flow-reversal reactor (TFRR), has emerged as a potential solution to ventilation air methane (VAM) emission mitigation. One manufacturer of TFRRs has demonstrated its oxidizer design (the VOCSIDIZER?) at coal mines in the United Kingdom and Australia. These demonstrations tested the technology?s effectiveness at oxidizing low-concentration methane, as well as its ability to tap the excess heat to produce steam for electric power generation. In early 2007, the first U.S. demonstration of this technology began operation at an abandoned mine in West Virginia. The project is designed to prove the technology?s operational robustness, its ability to reliably oxidize methane at concentrations typical of mine exhausts, and its safety. If the technology is employed at active underground coal mines, it offers the potential to mitigate substantial quantities of global methane emissions. This paper discusses global VAM emissions, options for the recovery and utilization of VAM, and existing projects such as WestVAMP in Australia and the ongoing U.S. VAM demonstration project.

Jan 1, 2009

By Gene Mattila, Ron Boyd

Introduction Rock bolting is a general term that encompasses pinning, roof bolting, rib bolting, and cable bolting. Rock bolting contributes the highest nonproductive cost and is the most significant safety risk in mining today. Total installed bolt costs are now more than $20 per bolt. Rebolting or repair work doubles this. And bolting accidents account for about 30% of all fatal and nonfatal lost time accidents. It is only logical, then, for the mine operator to install the highest quality anchors possible. Every bolt on the market - tensioned, untensioned, full contact, or point anchor - has designed capabilities in axial, shear, and fluctuating ground conditions. Bolts will provide a designed support if material specifications and installation procedures fall within the manufacturer&apos;s recommendations. This also assumes that there are no unexpected geological or operational changes. Proper material specifications and installation procedures should guarantee the mine operator a quality anchor. To help assure this, the Mine Safety and Health Administration (MSHA), the US Bureau of Mines (USBM), and the AMC Manufacturers group developed stringent ASTM materials standards. These govern mechanical point anchor bolts and bolts using threaded and nonthreaded rebar. There are also minimum standards that suppliers must comply with in the manufacture of frictional bolts. However, most frictional bolt standards are based on the manufacturer&apos;s own specifications. It would be impossible to set uniform regulations on frictional bolts. Each bolt provides support in a slightly different manner and thereby requires different material needs. Quality Control In any case, material quality can generally be assured through tight order specifications and periodic quality control checks. The problem with installing quality anchors does not solely lie with the material. It includes all the events that occur from the time a bolt leaves a manufacturer to the time it is installed. The anchoring ability of any major type bolt can be affected by transportation, storage, mechanical performance of installation equipment, installation demands of the operator, proper drilling accessories, and local geology. Table 1 and Fig. 1 document the negative events that can affect each bolt and the degree to which it can be affected. Drilling a hole of oversized diameter, for example, is an operator controlled factor. It will adversely affect most bolts. An over-sized diameter reduces, or even eliminates, the anchorage capability of a mechanical shell. It will reduce the support capacity of a split set to nearly nothing. And it will cause a partial or incomplete grouting around the resin bolt. Frequently, due to bit wear, holes are drilled undersized in diameter and may not be properly cleaned out. In this case, it will be difficult for the operator to push the mechanical shell into the hole, thereby causing him to drill another hole. In cases where the bolt is obviously not providing anchorage, operators will probably drill another hole and place another bolt. Rock Bolt Regulations It is the situations where a bolt is improperly installed in the hole, but gives the appearance of a good bolt, that are frightening. In fact, some safety officials and engineers believe that only 50% to 60% of installed bolts are working. These bolts cause irregular ground load transfers in other bolts and overload them. This causes hazardous situations and overstressing. It is these bolts that fail prematurely 200 to 255 mm (8 to 10 in.) behind the face and possibly contribute to the high accident rate. The government and several manufacturers recognized the need to check the integrity of rock bolts. These programs are in different stages today. Tight torque regulations have been established for mechanical

Jan 4, 1985

By J. B. Hiskey, V. M. Sanchez

Electrochemical oxidation of arsenopyrite (FeAsS) has been investigated as an attempt to gain a better understanding of its dissolution chemistry. Rest potential measurements, cyclic voltammetry and constant potential experiments were conducted in the pH range from 8 to 12 in the absence and the in the presence of cyanide. A two-step reaction sequence is suggested by the electrochemical measurements. The initial step is described by: [FeAsS+6H20=Fe(OH)3+H2AsO3- +S°+7H++6e] The second step involves the oxidation of the arsenite and sulfur according to the following reactions: [H2As03-+H20=HAsO24-+3H++2e and S° +4 H2O=SO4-+3H++6e] Stoichiometric determinations confirm that 14 electrons are involved in the overall reaction.

Jan 1, 1992

By Paul S. Fisk, Arne Fareth, Julie Frietas, Francis Lo, Fidel L. Mallonga

INTRODUCTION This report describes the inspection of parts of the New Croton Aqueduct (NCA)undertaken for the New York City Department of Environmental Protection (NYCDEP)by Parsons Brinckerhoff Quade & Douglas, Inc., (PB) in association with Montgomery Watson Engineers of New York, P.C. (MWH). Support for the inspection was provided by AFC Enterprises, Inc., under Construction Contract CRO-333, “WM-11 New Croton Aqueduct Rehabilitation and Inspection Program.” The scope of the inspection work under CRO-333 included assessing the condition of the 10.3 km (6.4 mile) long, pressurized section of NCA and inspection of shafts, head houses and blow-off structures in both the pressurized and gravity sections. The CRO-333 inspection continued investigation work begun under ContractCRO-196, which ran from 1993 to 1997. The CRO-333 inspections were conducted from November 2004 to September 2005. Background The New Croton Aqueduct was put into service in 1891 to deliver water from the Croton River Watershed in Westchester County to consumers in New York City. Figure 1 shows the location plan of Croton Water Supply System. The design flow into Jerome Park Reservoir was 12.7 m3/s (290 mgd) and into the135th Street Gate House, further south, was 10.9 m3/s (250 mgd). The NCA has been operated as a gravity conduit from Croton Lake to Gate House No. 1, just north of Jerome Park Reservoir, since its original construction. The length from Gate House No. 1to 135th Street, which includes a major siphon under the Harlem River, has been operated under pressure. Croton Lake gate house, the north end of the alignment lies at Station 4+75; Shaft 33, the south end of the alignment lies at Station 1628+05. The diameter of the tunnel is 3.2 m (10.5 ft) in the siphon and 3.7 m (12.3 ft) in the Bronx and Manhattan sections. The pressurized sections, constructed in rock, consist of a brick lining surrounded by a mortared and grouted rubble backing. Figure 2depicts a typical tunnel cross section. The objective of the shaft and tunnel inspections was to locate and document defects, such as leaks, deterioration of lining material, cracks, spalls, delaminations,

Jan 1, 2007

By D. Brady

When deciding to deploy rescue teams underground the decision makers need to be able to determine that there won?t be an explosion whilst the rescue teams are underground. Previously general body concentrations in areas likely to be travelled were compared to explosive limits on a one off basis with no formal process looking at trends or other areas. A new approach is being adopted that takes into account the rate of change of gas concentrations with triggers set to enable a withdrawal of personnel prior to a possible explosion and influences such a barometric pressure changes. This paper explains the rationale behind the changes made and the advantages and implications of adopting such an approach.

Jan 1, 2012

By Baolin Qu, Jingxin Wang, Cuncang Xu, Bing Wu, Mingyu Zhong

With the development of the coal mine regulation regime, the situation of coal mine safety production in China has continued to improve. However, coal mine accidents have not been fundamentally eliminated; constantly learning from historical accidents can make mining work safer. Therefore, to better understand the coal mine accident characteristics, this study analyzes the tendency of coal mine safety accidents from multiple perspectives, among which all accidents after the establishment of the State Administration of Coal Mine Safety in 1999 are the top priority. The results show that strict national policy, technological progress, and reasonable coal prices are conducive to the safe development of mines. On the contrary, high-intensity centralized production will lead to frequent accidents in the peak season of coal production. In addition, the type of coal mine ownership will have an indirect impact on the occurrence of coal mine accidents. The research results not only play a positive role in the prevention and control of coal mine accidents in China but also have reference meanings for the safety production of coal mines in other countries in the world.

Dec 28, 2022

By Ven Mercade

The flotation of calcite has been studied by many investigators, especially in terms of type of collector; pH; and metal ions that activate and, more importantly, depress the flotation of calcite (1)(2). Research was extended to the investigation of the effect of polyvalent metal salts and sodium silicate using these materials added separately or in mixtures (3)(4)(5)(6). Flotation of calcite was also studied with respect to its function as a carrier in the beneficiation of kaolin clays by Ultraflotation (7) (8) (9). The carrier used in Engelhard Minerals & Chemicals Corporation&apos;s industrial Ultraflotation operation is calcite. This fact, coupled with the continuing interest in Ultraflotation phenomena, led to a study to determine the effect of polyvalent metal-silicate hydrosols on the flotation of calcite.

Jan 1, 1978

By M. Gangal

CANMET-MMSL, in cooperation with Dry Systems Technologies and Quinsam Mine, conducted a study to determine the effects of B50 biodiesel on the emissions of a flameproof diesel power package in comparison with mining diesel fuel for application in underground coal mines. The emissions testing for coal mine application requires that the intake air mixture to the engine should be at 1.25 percent methane by volume in air. The tested power package system included a naturally aspirated, mechanically-controlled diesel engine with a diesel oxidation catalyst (DOC), a heat exchanger, flame arresters, and a low temperature disposable diesel particulate filter. The engine dynamometer tests were conducted at the CANMET-MMSL Diesel Emissions Research Laboratory in Ottawa using the ISO 8178-C1 test protocol. The separate and combined effects of a B50 biodiesel blended fuel, and with and without 1.25% methane enriched intake air were measured on a diesel power package. Fuelling the baseline engine (without methane), with B50 biodiesel blend reduced carbon monoxide (CO) by 44%, and increased nitrogen dioxide (NO2) by 19%, and particulate matter by 31% relative to the mining diesel fuel. Similarly, injection of 1.25% methane to the intake air for baseline engine with mining diesel fuel increased engine power by 15%, CO by 124%, and NO by 15%, and decreased NO2 by 13%. The effect of B50 biodiesel relative to the mining diesel for coal mines application (with methane for both fuels) was to reduce CO by 27%, and NO by 6%, and increase NO2 by 23%, with no change in engine power. The overall results indicate that the minimum ventilation rate for the equipment application in coal mines with B50 biodiesel was 4.11 m3/s (8,700 cfm), slightly higher than the ventilation rate of 4.01 m3/s (8,500 cfm) with the mining diesel fuel. This slight increase in ventilation rate for B50 biodiesel fuel was due to an increase in NO2 at one of the operating test points, and the ventilation rate for this equipment was governed by NO2 in the exhaust gas.

Jan 1, 2009