Search Documents

By John P. Capp

In recent years limited markets have been developed for fly ash, the dust removed from coal-burning powerplant stacks, but most of it is still dumped in spoils areas at a cost ranging from 20 cents to $1.75 per ton. Aside from this cost, the creation of huge spoils areas can present a considerable aesthetic problem. Since the present annual fly ash output of about 20 million tons will probably reach 30 million by 1970, and because satisfactory disposal areas are becoming more limited, markets for much larger quantities of the waste are needed to keep disposal costs from becoming a significant economic factor in coal-burning powerplant operation. Current stress on air-pollution control and beautification, plus the vital need for good powerplant economy, makes it imperative, therefore, that coal producers and consumers expand markets and develop new applications for fly ash. Markets for established uses can be increased by making a greater effort to sell fly ash. New large tonnage markets for fly ash should be sought via more intensive, coordinated research. The economics of fly ash utilization underscores the vital role that must be played by research. To be competitive with other products, processes for the conversion of fly ash into marketable materials face difficulty in regard to two important economic factors--transportation cost and product utility--the other economic factors are favorable. Raw material costs of fly ash, for example, are quite attractive, and supply is no problem because there are many coal-burning powerplants in operation and many more are planned. Demand for products made from fly ash will grow if their utility is established and a good sales program is initiated. The major problems then are transporta¬tion costs and development of useful products.

Jan 1, 1966

By B. J. Scheiner

The Bureau of Mines, Department of Interior, has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. Lt was found that at a given polymer concentration, there was an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By F. M. Stephens

This paper is to be presented at the annual meeting of the American institute of Mining and Metallurgical Engineers, San Francisco, February 1959. Permission is hereby given to publish with appropriate acknowledgements, excerpts or summaries not to exceed one-fourth of the entire text of the paper. Permission to print in more extended form subsequent to publication by the Institute must be obtained from the secretary of the Institute. If and when this paper is published by the Institute, it may embody certain changes made by agreement between the Technical Publications Committee and the authors, so that the form in which it appears here is not necessarily that in which it may be published later.

Jan 1, 1959

By Alan Rhodes

This study is initiated to investigate the efficiency of separation of mineral slimes using electroflotation as compared to that of column and conventional flotation techniques. Important parameters such as collector concentration, pH, current density, aeration rate, etc., have been studied. The results indicate that electroflotation can be used more efficiently in processing rutile slimes (10 µ) under certain operating conditions.

Jan 1, 1982

By D. A. Dahlstrom

Since the initiation of continuous vacuum filtration over a half a century ago, control of the performance of these units has been largely in the hands of the plant operators, Obviously there has been the introduction of variable speed drives, adjustable speed feed slurry agitation, vacuum control, etc. However, control of , filtration rate, cake moisture content, dissolved solids recovery by cake washing and dryness of solids where thermal drying is practiced is primarily up to the operators judgment and the settings he imposes on the controls he regulates, - filter cycle time, submergence, vacuum level, filter medium condition, wash water- rate, and other such factors. While this may seem to indicate that good operators are a paramount necessity, and certainly always desirable, a considerably more vital factor is a properly designed filter and filter station for the particular application. With improper design, highly skilled operator control will still leave much to be desired in the way of process performance. On the other hand, with correct design and application, the operator can easily and quickly control normal plant surges and quality variations within the flow sheet. Due to the growing complexity and inter dependency between the various processing steps in the modern flow sheet as well as the rising costs of capital investment, labor, maintenance, and losses involved with off quality product or insufficient recovery, automatic or inherent performance control of many of the unit operations within the metallurgical mill must be achieved. Continuous filtration should and can be susceptible to such control. However, as every instrument engineer knows, before control and automation can be achieved, a basic understanding of the operation is mandatory. This is primarily due to three factors. First, as in so many control applications, it may not be possible or feasible to measure the factor that it is desired to control. Thus, secondary variables that influence the major factor are substituted for control purposes. Secondly, it is always desirable to take advantage of any ?self-regulation? within the operation being performed on the equipment. In so doing, not only will automatic control be facilitated, but instrumentation is minimized while experiencing most efficient operation. Finally, automatic control is not a cure-all for improper process and equipment design and application. Hanging instruments on such an operation can be compared to constructing a sizable building on sand, Results will be disappointing.

Jan 1, 1960

By R. L. Grayson

The health and safety of employees, efficiency of the operating system and production are paramount goals in underground coal mining. The section foreman assumes responsibility for making his part of the total system function to meet these goals. However, section foremen often have not been prepared to assume the full range of their responsibilities upon becoming a supervisor. This discussion addresses the full range of section foreman responsibilities and concomitant authority. Management principles that must be mastered by him are presented, and performance expectations as well as criteria for their evaluation are examined. The benefits realized from effective foreman training are discussed.

Jan 1, 1985

By Douglas W. Barr

If some of you have been through the long hot summer in the southwest, you may find it refreshing to turn your thoughts to the wintertime problems of mineral processing in the northern climates. The purpose of this paper is to point out some of the ways in which heat is gained or lost in the tailing basin operation and the problems that can result if too much heat is lost.

Jan 1, 1980

By D. R. Taylor

Treatment of bentonite clay with mineral acids yields a modified clay product of high surface area and acidity which exhibits enhanced adsorptive and catalytic properties. A highly specialized segment of the clay industry based on this process has evolved into worldwide business with a capacity of about one-half million tons/yr. This paper will present data on the chemistry, mining, manufacturing and applications for acid- activated clays.

Jan 1, 1986

By Prakash C. Kapur

A principal first order and a minor summation term contribute to the solution of the discretized batch grinding equation when formulated in cumulative retained mode. Depending on the interrelationships between the selection and breakage parameters, the minor term may be advantageously modified in a number of ways. The reduced grinding equations thus obtained are solved by iterations to give relatively simple solutions which are tested against experimental data. The implications and advantages of the reduced grinding equations are briefly discussed.

Jan 1, 1969

By William W. Leathen

Acid mine drainage became a reality through the exposure of the first bituminous coal seam, either by man or by nature. At first the small amount of acid formed was quickly and efficiently neutralized by basic rock strata and by neutral or alkaline water. As soon as extensive mining operations overtaxed nature's own defensive measures, acid mine drainage became a problem of concern to government and the coal industry. It was the purpose of the studies conducted at Mellon Institute to accumulate knowledge, both applied and fundamental, relating to the formation and disposal of acid mine effluents. It was during this program that the microbiology of acid mine water was studied. Most bituminous coal mine effluents are highly acidic and contain, along with other ions, high concentrations of ferrous iron. The acid is sulfuric, and. the iron is present as the sulfate; both are the oxidation products of iron sulfides (FeS2) which are present in the form of pyrites, marcasites, or other sulfuritic minerals. The oxidation occurs, in the absence of moisture, according to the following reaction: [ ]

Jan 1, 1959

Adsorption of acrylamide based homo and copolymers on hematite was investigated as a function of phe nature of the polymer charge and functionality of the polymer. Effect of addition of sodium dodecylsulfonate and dodecylamine hydrochloride was also studied and was determined to result in an increase or decrease in the amount of polymer adsorbed depending on, the charge characteristics of the surfactant and the polymer, pH of the suspension, concentration of the various species and the order in which these species were added to the system. The surfactant adsorption under given conditions on the other hand, was found not to be affected by the presence of the polymer molecules. The data is analyzed to elucidate the mechanism of adsorption of polyacrylanide type polymers on hematite both with and without the surfactant species king present in the system.

Jan 1, 1982

By George K. Martin

This paper deals primarily with roof bolting in Kentucky coal mines from January 1, 1949, through December 31, 1954, a six year period. The Consolidation Coal Co? (Ky.), a division of the Pittsburgh Consolidation Coal Co., began systemmatic roof bolting in November 1948 in Mine #204, Elkhorn #3 Seam, at Jenkins, Kentucky, After the efficiency of roof bolting had been proven by the Consolidation Coal Co., this procedure was adopted by other companies throughout the state. In December 1954, approximately 46.4 percent of Kentucky's total production of coal from underground mines was obtained from roof-bolted areas. Statistics in this report will show the progress made in roof bolting during the six years, in addition to the roof bolting being done as of December 31, 1955. Significant progress has been made in the coal mines of Kentucky in reducing the roof-fall fatality, rates, during the past several years by adopting systemmatic roof bolting. The ground work by the Consolidation Coal Co, (Ky.) in cooperation with the Federal Bureau of Mines was based upon the previous experience of the St. Joseph Lead. Cc, in its Southeastern Missouri Mines and The Tennessee Coal and Iron Division of the United States Steel Corporation. The author gratefully acknowledges the cooperation and assistance given by officials of the various mining firms using roof bolts, the Kentucky Department of Mines and Minerals, and the Federal Bureau of Mines in furnishing photographs and information.

Jan 1, 1958

By W. R. Hibbard

Emerging from discussions of U.S. energy policy: from the Project Independence Blueprint; from President Ford's statements to Congress; and from several independent appraisals of the situation; there is a clear objective to achieve an appropriate balance of supply and demand in the near term future (1) by developing more efficient ways of using energy and (2) by extending domestic sources of energy. More specifically, the strategy for achieving this goal has three parts (1) Conservation of energy through greater efficiencies in automobiles, appliances, lighting, heating, and industrial processes. (2) Increased domestic production of oil and gas through new sources such as the outer continental shelf and new efficiencies such as tertiary recovery. (3) Substitution of coal and uranium for oil and gas in utility power plants and industrial heating. The goal of energy research and development is to help achieve these goals and to help minimize the economic, environmental and social impact of our shift from imported energy to domestic sources. The focus of this paper is the implications of the expanded use of coal, and the research and development which may help achieve the above goals in so far as coal is concerned.

Jan 1, 1975

By Josef J. Schwegel

The first vertical shaft lime kiln operating according to the parallel-flow regenerative principle was developed and built in the nineteen-fifties by Schmid-Hofer in Austria. Upon proving this concept of calcining or "burning" limestone to be very energy efficient for the production of good quality lime, Maerz Ofenbau AG of Zurich, Switzerland was in 1965 licensed for the design detailing and construction of these kilns. The first regenerative shaft type lime kiln outside of Austria was built in 1966 and through close co-operation with customers and their operating personnel, the advanced technical developments of today's kiln designs were accomplished. At present approximately 190 kilns of this type in capacities ranging from 60 to 700 short tons per day have been built or are under construction throughout the world in highly industrialized as well as less developed countries.

Jan 1, 1981

By Raul A. Deju

This paper shows how one can relate the chemical reactions between water and a silicate bed to the equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented.

Jan 1, 1969

By V. R. Manukonda

Selective flocculation of iron ores is extremely sensitive to the type and the amount of soluble salts in pulp solutions. Chemical precipitation of alkaline earth ions combined with ultrasonic treatment deactivates their adverse effects without using any environmentally ill-defined reagents. The manner in which ultrasonic treatment affects starch adsorption on hematite, dissolution of quartz, and selective flocculation process was investigated. Selective flocculation tests were conducted in the presence of up to 400 ppm calcium ion on a quartz-hematite mixture by precipitation as calcium carbonate, and the role that silicate ion generated by ultrasonic treatment plays in achieving the selectivity of separation is discussed.

Jan 1, 1987

By J. D. Miller

Physical separation of bitumen from low-grade Utah tar sand deposits containing a relatively high viscosity bitumen phase (Sunnyside and Tar Sand Triangle deposits) has been accomplished by traditional size reduction and froth flotation techniques. At appropriate experimental conditions more than 90 percent of the bitumen can be recovered in a concentrate, containing more than 20 weight percent bitumen, which should be a suitable feed material for subsequent hot water or thermal processing. The efficiency of bitumen recovery depends on the extent of size reduction, promoter and dispersant addition. Rejection of greater than 60 percent of the sand at ambient temperature and ease of water removal from the concentrate make such a process strategy both energy and cost effective. The energy required to achieve effective separation by the ambient temperature process is significantly less than the energy required for the recently developed hot water process. The flotation behavior of the tar sand has been analysed with respect to flotation pH, contact angle measurements and the apparent iso- electric point of the bitumen. The best flotation response at pH 7.8 to 9.0 can be correlated with the maximum in contact angle developed between the air bubble and bitumen surface and with the apparent iso-electric point of the bitumen (-pH 8.0).

Jan 1, 1981

By Harold L. Lovell

The current interest in sulfur recovery from coal measures is indicated by a recent report prepared for the Public Health Service (1) It was noted that the concentration of pyrites to a product containing 42-48 percent sulfur should be relatively easy with present equipment. It was also pointed out that a utility potential exists for the high-grade iron concentrate which results as a by-product of the consumption of pyrites in the acid-making process. However, economics, marketing characteristics, location, transportation, pyrite levels and coal characteristics all strongly influence the feasibility of fostering industrial development of such processes. The extent of pyrite recovery and product quality is intimately related to pyrite particle size and its degree of liberation, a consideration usually given greater emphasis in metal ore preparation than in processing coals. Consequently, fine crushing to nearly 20 mesh probably will be essential for maximum practical processing. It appears that any process separating pyrites from a coal must involve a reprocessing of the normal preparation plant refuse, although some yields can be attained from certain existing operations as products from, a shaking table or a jig. Further, the existence of millions of tons of coal refuse cannot be ignored as a mined source of raw materials. The recovery of saleable products from such wastes, although untried on a large scale under current conditions, not only offers a realistic source of sulfur but also would achieve a secondary refuse with the minimal contents of substances which incite and propagate the burning of organic and inorganic combustibles. These silicate materials, thus beneficiated, also offer some potential for economic utilization. Some significant tonnages of pyrites have been produced from coal measures in the past, but the experience was, in general, not consistent with current coal preparation practice. The processes involved did not include cyclones and heavy media; nor were they carries out under the sociological environment concerned with pollution as exists today.

Jan 1, 1967

By Bryson D. Trexler

Man's activity in developing, operating, and abandoning a mine often affects the quality of the ground water and surface water. Acid water drainage from mines is an example of an impact from mining that results in degradation of ground and surface water. New flow systems are created by the mining activity. The mining made possible complex chemical reactions that, with water movement, create a discharge of low pH, poor quality water. Remedies for these problems fall into two general solutions: 1) treatment of the end product and 2) reversal of some aspect of man's disturbance of the natural system. The relative reversibility of various aspects of man's impact from mining activities ranges from relatively easy to very difficult, from economically feasible to economically infeasible, and from technically possible to essentially impossible with present knowledge. The relative reversibility of a mine-related problem cannot be assessed without first understanding the detailed physical interactions that combine to form the problem. Acid water drainage is a combination of the availability of several chemical factors with the availability of water for a transport mechanism.

Jan 1, 1982

By J. Herman

The Mid-Continent Geophysical Anomaly (M.G.A.) which extends from Michigan into Wisconsin, Minnesota, Iowa, Nebraska, and Kansas, has recently been the object of intense preliminary oil and gas exploration activity involving widespread land leasing, seismic data collection, permitting of deep exploratory holes and other activities (Paul et al., 1985). This report describes the remote-sensing techniques and results of the application of these techniques to study the geology of the M.G.A. and the surroundings in Iowa. In early 1981, Coal Valley Natural Resources contracted Geospectra Corporation to find a large, (100,000 acres or larger) lease block for wildcat oil and gas exploration. The southwest Iowa area was chosen for several reasons. First, southwest Iowa contains the northeast portion of the Forest City basin (Figure 1) which has produced oil and gas from numerous fields in Kansas, Missouri, and Nebraska (Landes, 1970; Petzet, 1982).

Jan 1, 1986