Search Documents

By Hubert E. Risser

At the outset of a discussion on the adaptability of Illinois coals for use in iron and steel production, it is perhaps well to define terms. ?Adaptability? as used in this context, means that a coal can be, adapted to use within a given technological and economic framework. For a coal to be adaptable, to use in the manufacture of metallurgical coke within the present technological and economic framework, it must possess, among other things, at least the following characteristics: 1. The coal must be capable of producing, alone or in combination with other coals, a coke that can meet at least a minimum standard of required performance in the present-day blast furnace. The coke must have sufficient strength, stability, hardness, and freedom from impurities to make it suitable. 2. If the coal in its raw form does not meet these requirements, it must be amenable to beneficiation or upgrading so that the requirements can be met. 3. It must be available in uniform quality and in sufficient quantities to meet the need. 4. Use of the coal must be economically attractive. If its quality is equivalent; to that of the coals with which it must compete, it must be no more expensive than they. If It is better, a premium price may perhaps be demanded. If, in any respect, it is the least bit less suitable, the cost must be lower to offset its disadvantages.

Jan 1, 1961

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center&apos;s 900-lb/hr pilot plant, approximately 85 percent of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to <1,000 ppm equivalent Si02, while maintaining a Ca(II) content of 516 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water.

Jan 1, 1970

By N. A. Frazier

The technology for using limestone or lime to scrub SO2 from power-plant flue gas has significant implications to the limestone industry. A brief status report on these processes will be made, possible process requirements on the limestone properties will be reviewed, and projections on the buildup of demand with respect to time will be reviewed. Disposal problems inherent with the use of these throwaway processes will also be summarized. Given a viable technology, relations among (1) distance of power plants from low- and high-sulfur coal and limestone deposits, (2) modes of handling and transporting immense tonnages of bulk material-coal and/or limestone, and (3) regional air-quality standards are some of the factors which will ultimately determine the demand for limestone. A discussion of these factors will be presented, with the intent of identifying geographic regions where significant increases in production can reasonably be expected.

Jan 1, 1974

By James P. Connell

The Montana Operations of the Anaconda Company constitute an integrated, though geographically separated, non-ferrous metal production complex. The mines are located at Butte and consist of one large open-pit mine, two small underground mines, a precipitation plant for both underground and pit-dump leach water, and the Weed Copper Concentrator. The smelter, located at Anaconda, Montana 25 miles to the west, processes all Butte copper shipments as well as copper materials from both Anaconda and private mines. Copper and zinc are refined at Great Falls, Montana, 165 miles to the north. Other facilities developed over the years include the Anaconda Forest Products Division, the Butte, Anaconda, and Little. Chicago Water Companies, and the Montana Hardware Company. Data processing for these operations has been performed on an IBM 360 Series, Model 30 computer, utilizing a Disc Operating System. This was replaced in September 1970 with a 360 Series, Model 40 128K unit. In addition, some data processing is also done for Anaconda Company operations located at Britannia Beach, British Columbia; Columbia Falls, Montana; Yerington, Nevada; and Twin Buttes and Tuscon, Arizona. The material under discussion in this paper will be concerned primarily with the mining operations at Butte.

Jan 1, 1970

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of fluorspar from 35 domestic and 50 foreign, mines and deposits in 13 countries. Only 6 domestic properties are considered to be economic reserves, as 29 domestic deposits were found to have an average total cost of production that was uneconomical at a breakeven (0 pct) DCFROR. The 50 foreign properties evaluated were selected to represent at least 85 pct of the known demonstrated fluorspar resources located in market economy countries and China. All evaluated foreign operations were found to be economic to marginally economic in January 1984 dollars. World demonstrated ore reserves of 344 million metric tons (mt) containing 123 million mt of CaF2 were evaluated for the 56 operations. Average total costs needed to cover all costs over the life of each operation were determined for all recoverable fluorspar products. Comparisons of mining, beneficiation, and transportation costs per mt of fluorspar concentrate illustrate advantages between countries. Of the three largest producing countries, China, with its high-grade, low-cost operations had the lowest weighted average total cost of production ($38/mt concentrate). Mexico was next at $54/mt concentrate, and South Africa needed an average of $90/mt of concentrate to cover all costs of production for its low grade deposits.

Jan 1, 1985

By H. E. Cross

In a minerals-recovery context, the object of exercising control over milling operations must be threefold, 1) To achieve maximum recovery at 2) minimum operating costs and 3) making maximum use of installed equipment, Milling is one of a sequence of operations which have as their objective the economic recovery of minerals from mined ores, All operations in the sequence are interdependent and each is both influenced by and itself affects all other unit processes. The part which grinding plays in achieving each of the above objectives is indicated in the following analysis: In South Africa, the most important mining operations are still the gold mines, A vast reservoir of knowledge and experience in treating the Witwatersrand and associated ores has been accumulated. and recoveries are consistently high, However residue values do vary and frequently this is due to fluctuations in the degree of grind, The significance of changes in residue values is indicated by the following example: On a modern mine, the residue values varied from 0,25 to 0,33 dwi; per 2000 lb, during a period of 6 months, The cash value of the gold thus lost varied therefore between $0.44 and $0.58 per 2000 lb, ton. A residue which assays 0.30 dwt per ton would contain approximately 0.26 dwt as undissolved gold and 0,040 dwt per ton as dissolved gold present in residual solution after filtration. This dissolved gold loss is a function of efficiency of filtration and varies from 0.030 to 0,.070 dwt per ton of residue.

Jan 1, 1970

By Harry Wolf

The chemistry of the element uranium enables industry to employ either an acid or alkaline carbonate leach solution for most uranium ores. Either method my be used for conventional, in-situ, or heap leaching. Uranium recovery in the leaching process depends both on the solubility of the uranium minerals and, on the access of the leach reagent to them. The uranium leaching rate is proportional to the liberated mineral surface area and the chemical reactions involved in the dissolution step. The dissolution of U(VI) and the oxidation of u(IV) to U(VI) are the basic chemical reactions in the leaching process. The active surface area is a function of the effective porosity and the particle size of the ore (1). Ore pieces, with a high porosity and high permeability, may provide a large active surface area even in coarser fractions. This type of ore might be suitable for heap or in-situ leaching techniques. Nonporous and impervious ores are usually more amenable to conventional milling where the active mineral surface is exposed by grinding the ore down to the liberation size of the mineral.

Jan 1, 1981

By James E. Brewer

Procedure for approval by the U. S. Army Corps of Engineers of a new source of aggregate is in three phases. Phase 1 consists of an investigation of a quarry or proposed quarry by district geologist and laboratory geologist and/or petrographer. The quarry face or suitable outcrop is logged in detail or, if exposures are poor, cores may be taken to determine whether further investigations are warranted. Phase 2 consists of thorough laboratory testing. Cores and crushed material are subjected to a number of acceptance and quality tests for soundness, absorption, abrasion, reactivity, and other properties. Petrographic analysis is also made. Phase 3 is a physical and economic study of the site and involves determining quantity of stone avail- available, amount-and character of overburden, condition of haul roads and distance to rail shipping point, plant flow sheets and capacity, aggregate sizes produced, and approximate price of material at plant.

Jan 1, 1966

By Donald W. Gentry

This paper presents some of the results of a rock mechanics in¬strumentation program designed for, and implemented at, longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam and immediately below the coal seam. Longwall test panel 411 had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft). The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) al¬though it ranges from 73-134 m (240 - 440 ft). Roof support at the face was provided by Hemscheidt shields. These shield-type supports weigh 11.4 metric tons each.

Jan 1, 1977

By Lynne Chastain

The Eastern Shoshone and Northern Arapaho tribes of the Wind River Indian Reservation, Wyoming are interested in developing their industrial mineral resources. The U.S. Bureau of Indian Affairs (BIA), Division of Energy and Mineral Resources (DEMR) is assisting the tribes in evaluating the potential of their industrial mineral prospects for development. Gypsum occurs on both sides of the Owl Creek Mountains in the basal portion of the Jurassic Gypsum Springs Formation. The gypsum resources that are being evaluated crop out along the northern flank of the Owl Creek Mountains in the Sweetwater basin, a small topographic sub-basin of the Big Horn Basin. From October 1998, to April 1999, DEMR personnel mapped, sampled, and drilled the southcentral butte within the Sweetwater basin. Samples were analyzed for free and combined water, and major mineral oxides to determine gypsum purity. Gypsum purity averaged 93.6 percent for surface samples and 95.1 percent for drill core samples. The basal portion of the Gypsum Springs Formation is comprised of several beds of gypsum up to 9 feet (2.7 m) thick separated by 0.5 to 2.0 foot (0.15 to 0.61 m) thick lenses of siltstone and limestone. Overall gypsum in the formation ranges from 35 to 90 feet (11 to 27 m) in thickness. A resource of approximately 7 million short tons (st) (6.4 million metric tons [mt]) has been identified.

Jan 1, 2001

By M. K. Rizkalla

This paper discusses the time-dependent behaviour of rock when it involves the presence of several layers of rock strata in the vicinity of mine openings, mining in sequences and the placement of backfill. The paper describes numerical techniques which proved useful when such situations are encountered in practice. The model is elastoviscoplastic. At given time stations, short term loading or changes can be made to the creep behavior of the rock. The modelling technique is first described and is followed by simulations of stresses and displacements in a potash mine with the primary objective to demonstrate the effect of such aspects as mining and fill sequences in 3-D. This involves cutting finite elements representing the strip of the mining face and simultaneously filling those elements representing the newly placed fill. The stiffness of the fill varies with the degree of compaction at each point. In this way, the effect of the time of fill placement, the gap between the top of the fill and the back as well as the degree of compaction are simulated. The second example is a 2-D problem simulating the long term effect of backfill, as a material compacting with time, on the settlement of the layers above it as well as the closure of the room.

Jan 1, 1996

By Lancelot E. Kun

The high-rate floc blanket clarification process developed by the Anglo American Corporation of South Africa is capable of continuously clarifying gold and uranium pregnant solutions containing 200-2500 mg/L suspended solids to below 25 mg/L solids at an average rising velocity of 8 m/h at the low process cost of R0,001-0,002 per ton of liquid treated. Overall process cost savings are mainly due to increased polishing filtration cycle times.

Jan 1, 1984

By Bond. F. C.

Introduction Although autogenous grinding applications date back to the early years of mineral processing when tumbling-type mills were first used, there has been a renewed interest in this type of grinding over the past few decades. A review of the historical aspects of autogenous grinding is provided which follows the development of the various types of mills and processes. Wet and dry grinding operations using either autogenous or semiautogenous mills, including the Aerofall mill, are described. Em¬phasis has been placed on the test work required to evaluate the feasibility of using autogenous or semiautogenous grinding for a spe¬cific application. The factors which must be considered to establish the appropriate design criteria for these types of grinding circuits are discussed in detail. Successful application of these grinding circuits results from a thorough test program, a careful analysis of the test results, and a practical engineering approach to the design of the process flowsheet and milling equipment. Certain pebble milling applications, where the pebbles consist of the ore or rock itself, can be classified as autogenous pebble mill grinding, or better known as ore-pebble mill grinding. In the generic sense, pebble milling includes those grinding operations using a tum¬bling mill in which the grinding media consists of various types of pebbles, either ore or other pebbles, instead of metal balls. Conse¬quently, this subject is covered separately in Chapter 5, Pebble Mills. Operating data from many of the installations located throughout the world are included in this chapter. Our appreciation is extended to those companies who contributed this important information. History of Autogenous Grinding F. C. BOND Autogenous grinding, the grinding of ore by itself rather than by special metallic or nonmetallic grinding bodies distinct from the ore, has an old and honorable place in the art of mineral processing. It antedates the use of the rod mill and is only a few years younger than the development of the continuously fed rotating tumbling mill in which it is accomplished. Its history71, 72 is inextricably bound up with that of gold mining. Every important early development of autogenous grinding took place on ores of gold, except in one case of silver ore. In common with many other features of modern mineral processing, autogenous grinding would have been greatly retarded if the winning of gold had been so small a part of mining in the past as it is today. Gold unlocked the secrets of rock-on-rock grinding. In years past gold ores were crushed in stamp batteries and then flowed over copper plates covered with mercury which amalgamated the gold. The McArthur Forrest cyanide process for the dissolution of gold in a dilute alkaline cyanide solution appeared in 1890. With finer grinding it recovered more gold than could be won by amalgama¬tion alone. The first response was to stamp in cyanide solution and finer mesh screens guarding the stamp discharge. However, the fine screens greatly restricted the tonnage stamped, and they wore out rapidly. Rotating tumbling mills70, 73 were the obvious choice to grind the coarse product from stamps. Many of these were Gates tube mills; more than 1,000 of these were sold between 1907 and 1913. They were made in 6, 51h, and 5 ft diam, with lengths of 20 and 22 ft. The 5 x 22-ft size was the most popular. The term tube mill did not refer to the mill shape, but included all tumbling mills using grinding pebbles. The flint or chert rocks found along the coasts of Denmark and Normandy are probably the most durable and resistant to abrasive and tumbling wear of any on earth. They were much used in the early tube mills. The early linings were all silex or Danish flint blocks, cemented into place with portland cement. Local hard stones or cast iron blocks were also used later. The cast iron liners carried lifters and were not bolted to the shell, but were held in a tight circle against it by steel wedges hammered home between them. The first ribbed metal liners designed to hold grinding pebbles pounded into them by the mill action were developed at El Oro, Mexico, about 1905. These and the Forbes, Komata, and Tonopah types, as well as the Osborne type developed in South Africa within about five years, were very successful in reducing liner wear. They sometimes lasted two years or more, and equalled or exceeded the life of silex lining at a lower cost. Some of the types were patented. The pioneer name recorded in the history of autogenous grinding is that of Kenneth L. Graham. In 1907 at the Geldenhuis Deep Ltd. mine near Johannesburg, he ran a comparative test on two tube mills. One mill used pieces of the common gold ore, or banket, and the other used the customary imported Danish pebbles as grinding media. He published the first account of autogenous grinding.&apos;&apos; In a test lasting 81 days the ore pebbles showed a definite saving over the Danish pebbles. Graham&apos;s historic paper also describes the invention of B. Chew of the Crown Deep Mines of the first trammel to be attached to a grinding mill discharge. The first known account of autogenous grind¬ing printed outside of South Africa was the description of the Graham test in Mining and Scientific Press&apos;s The use of grate- vs. overflow¬discharge was also described at this time." The news of this successful test appears to have had immediate effect, for by the end of 1908 the number of tube mills on the Rand had increased from 72 to 120.76 Presumably, most of these mills were now using autogenous grinding. The ore was principally a hard conglomerate of quartz peb¬bles cemented by silica, and was eminently suitable for use as a grind¬ing media. It is unfortunate that in South Africa the new autogenous process continued to be called by its old name of pebble milling, since the name does not distinguish between grinding with ore and grinding with extraneous pebbles. For increased clarity the former is called rock pebble milling. The first historical stage in the development was what is now designated as secondary autogenous grinding, or rock pebble milling. It consists of grinding a feed all passing &apos;A in. or finer with ore pebbles about 2 to 4 in. in diameter. The next stage to develop was that now called intermediate autogenous grinding, where larger amounts of larger pebbles about 5 in. in size were used to grind ore which had been crushed to about rod mill feed size or somewhat finer. It was developed on the Rand and in other places where coarse stamp screens were used to increase mill tonnage. In many cases the early secondary and intermediate autogenous mills have now been replaced by conventional ball mills and rod mill-ball mill circuits, with the object of further increasing grinding capacity. The third stage to develop is designated as wet primary autogenous grinding, in which run-of-mine ore or a primary crusher product is all fed to the autogenous mill together. It developed many years later indepen¬dently in the United States and in South Africa. The fourth and most recent stage is that of dry primary autogenous grinding, which developed in the United States and Canada. All four stages originated in gold mining. The first use of commercial autogenous grinding outside of the Rand apparently took place five years later in 1912 at the Santa Gertrudis gold mine at Pachuca, 55 miles northeast of Mexico City. This was followed closely by an installation at Goldfields, Nevada, in 1914-1915. The first name associated with autogenous grinding

Jan 1, 1985

By G. A. Kordosky

The control of pH in solvent extraction circuits is an old technique (1,2) but one which has a large potential for future use. The equilibrium position of any reaction which has hydrogen or hydroxide ions, either as products or as reactants, can be controlled by pH adjustment. Several examples of reaction types which are important in solvent extraction systems and which also show a pH dependence are shown in Figure 1. The examples were chosen to show the wide variety of reactions which fit the above criteria, but it is not meant to be a complete listing of all the possible reaction types, Some of the reactions are presented in a simplified form. It is the intent of this paper to discuss pH controlled solvent extraction reactions for some relatively simple systems through more complex ones.

Jan 1, 1979

By William J. Cavanaugh

In 1967, Lone Star Industries, Incorporated, established a program to carry out the necessary Research and Development work to bring the Snyder Process to commercial application. The purpose of this paper, is to present the detailed metallurgical results gathered in comparing the Snyder Process of Comminution to conventional grinding techniques for the milling and beneficiation of certain ores and other materials. The ore primarily dealt with in this paper is a fine-grained magnetite ore, containing approximately 23% acid-soluble iron, from the Lake St. Joseph ore body of Steep Rock Iron Mines, Ltd., (Canada). This particular example was selected for presentation in this paper because extensive comparative results with conventional methods of grinding were available. Also briefly described in the paper are the comminution of other ores and materials such as porphyry copper ore and alumina.

Jan 1, 1973

By D. Pearson

About 15,000 tonnes of zinc per year is present in the dusts and fumes produced in electric arc and BOS steelmaking, secondary copper refining and brass ingot making. Apart from the use of some copper-smelter fumes for zinc chemicals manufacture, zinc is not recovered and their disposal by landfill entails some risk of pollution by leach-out. The paper describes processes for recovering the zinc based on leaching and electrowinning. It was shown that the procedures normally employed for purifying zinc-electrolytes derived from primary sources are sometimes ineffective for secondary materials. Alternative process routes are proposed. Source materials were leached with acidic or alkaline reagents and solvent extraction was employed for electrolyte purification in addition to the usual techniques involving precipitation. Examples of integrated flow sheets for specific source materials are presented.

Jan 1, 1980

By Dale A. Bivens

INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is currently being constructed for the United States Department of Energy in SE New Mexico. The purpose of the project is to store low level transuranic waste in an underground environment which will ensure a safe atmosphere for the life of the stored waste. Ohbayashi was contracted by the DOE to sink two shafts and underground drift development which will be used to conduct a series of long term experiments in order to finalize the suitability of the geology and the environment for the transuranic waste storage. The two shafts sunk at the WIPP site were excavated around a borehole by conventional methods. The excavation around a borehole eliminates some of the established blind bottom sinking techniques, but creates unusual problems which must be pre-planned and scrutinized closely. An analysis of the slashing to the borehole technique will be given. WASTE SHAFT The waste shaft (w/s) is 5.8 meters (19 feet) in diameter and will be used primarily to transport the radioactive waste to the underground storage area. A pre-existing 1.83 meter (6 feet) diam borehole was taken to a depth of 655 meters (2150 feet) to the existing drift; at this level, a 38 meter (125 feet) sump was installed using blind bottom sinking techniques. Geology The primary geology for the w/s excavation is redbeds, anhydrites, dolomite, mudstone and

Jan 1, 1985

By Michael J. Humenick

A laboratory experimental research project was conducted to evaluate the use of chlorine for the oxidative destruction of residual ammonia which may remain in ground water after in-situ uranium solution mining operations. The work tested the idea of the injection of high strength calcium hypochlorite solution into the mining zone to convert ammonia to nitrogen gas as a final clean-up process for ammonia removal from the ground water system. The paper details ammonia removal efficiency as a function of chlorine dose, reactant and product material balances, and how the concept may be used as a final ground water restoration process.

Jan 1, 1982

By James P. Connell

The Berkeley Pit of The Anaconda Company is located on the southeast slope of the Butte Hill, the legendary "Richest Hill on Earth," and is one of the largest pit operations in the world completely dependent on truck haulage. Through October 31, 1968, the Berkeley stripping and mining operations have moved more than 442,589,000 tons of material. Present scheduled production is at the rate of 260,000 tons per day, with a record quantity of 306,900 tons having been hauled on September 23, 1968. Although the Berkeley Pit has been in production only a little more than ten years, it has been the proving ground for many of the presently used large trucks. Beginning with the original R. G. LeTourneau 75-ton electric truck in 1960, Unit Rig 85- and 100-ton electric drives, Haulpak 65- and 105-ton electric drives, and Caterpillar 100-ton electric drives have all been tested under production conditions. In addition, engine development has kept pace with both 1000-hp diesel and 1100-hp gas turbine engines now under test. As the size of the Berkeley operation has grown, the truck fleet has changed in size and appearance in order to maintain economic mining costs. The original fleet consisted of forty-three 36-ton trucks with conventional mechanical drives. The present fleet is made up of eighty-nine trucks: nineteen 85-ton Unit Rig electrics with 700-hp diesel engines; sixty-nine 100-ton Unit Rig electrics with either 700- or 1000-hp diesel engines; and one 100-ton Unit Rig electric with an 1100-hp gas turbine engine.

Jan 1, 1969

By Paul H. Johnson

Heap leaching is a simple means of recovering copper from oxide and oxide-sulfide ores. Although this method requires relatively low capital investment, it suffers from low copper recoveries and relatively high acid consumption. The objectives of this study were (1) to determine what factors influence these shortcomings, and (2) to establish a basis of correlation. between laboratory and field testing. The principal methods of leaching copper ores at the present time are heap, dump, in-place, and vat. A number of references are presented in the bibliography on the theoretical and practical aspects of these methods. In the heap-leaching method, crushed or uncrushed oxidized copper ore is placed on a prepared drainage pad. Acid leach solutions are dis¬tributed over the top of the heap, caused to percolate downward through the ore bed by gravity, and are drained from its base. The leach duration is generally a matter of a few months. Dump leaching is used to recover copper from very low-grade oxide-sulfide pit-waste materials. Here again, leach solutions are, percolated downward through a heap. However, in this method, little or no acid is added to the leach liquors, prepared drainage pads are not used and the leaching cycle is generally measured in terms of several years. Leaching agents are usually autogenously generated by the breakdown of sulfide minerals within the dump.

Jan 1, 1970