Search Documents

By M. Z. Rashad

The purpose of this work is to determine the influence of sample length or size on the value of variance (Semi-variogram) to select the suitable length that is required to the geostatistical computations of ore evaluation. Three cases in Ghorabi Iron Ore were studied. The first one was on the iron fraction (Fe\) at which the semi-variogram gave an evidence to good continuity of the fraction in the ore. In this case, the length of sample has not important influence. The second case was for the Mn\ component of the same area where the semi-variogram has a nugget effect. The selected length for this case was 4 meters. The Cl fraction of the ore was the third case where the anisotropic phenomena was appeared and the suitable length is 3 meters.

Jan 1, 1992

By M. Z. Rashad

The purpose of this work is to determine the influence of sample length or size on the value of variance (Semivariogram) to select the suitable length that is required to the geostatistical computations of ore evaluation. Three cases in Ghorabi Iron Ore were studied. The first one was on the iron fraction (Fe%) at which the semivariogram gave an evidence to good continuity of the fraction in the ore. In this case, the length of sample has not important influence. The second case was for the Mn% component of the same area where the semivariogram has a nugget effect. The selected length for this case was 4 meters. The Cl% fraction of the ore was the third case where the anisotropic phenomena was appeared and the suitable length is 3 meters.

Jan 1, 1992

By Dianne C. Marozas

The U.S. Bureau of Mines is conducting research to evaluate the potential for developing an in situ leach mining process that will selectively extract manganese from oxide ores, leaving gangue relatively undisturbed. To accomplish this, a geochemical approach, based on deposit-specific information such as mineralogy and geology, is used to constrain the operating parameters of the system. Among the studies being conducted are (1) leaching experiments to define reaction mechanisms and kinetics, (2) detailed petrologic characterization at the microscopic scale to assess Mn distribution and leaching efficiencies, (3) deposit characterization and evaluation, and (4) development of potential Mn recovery schemes. Data from these studies are being used to develop engineering design information for an in situ mining process. Specific details of the Bureau's research project are discussed, including results obtained to date.

Jan 1, 1991

By D. X. Tang, G. Wilson, Y. Luo, S. S. Peng

Knowing the location of voids/fractures in roof rock will be greatly helpful for roof support design. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way for determining void location in roof rock. In this research, feed pressure and rotation torque are found to be good indicators for identifying the voids, based on the results of a series of laboratory experiments. A set of computational rules has been developed to locate voids in mine roof using the measured roof drilling parameters and implemented in MRGIS, a software package developed to allow mine engineers to make use of the large amount of roof drilling parameters for predicting roof geology properties automatically. Anew feature, 2D map+3D figure display, is also added to MRGIS.

Jan 1, 2004

By J. den Drijver, M. Opahle, R. Inderst

Safety reasons render necessary the advanced calculation of the amount of methane degassing from a longwall in the scope of the ventilation planning of mines. Today empirical methods, which are based on observations of operational procedures, are used for the calculation of the amount of methane. Despite of constant improvement those calculations are not always sufficient. In particular calculations which are based on operational facts but not proved by experience are not reliable. Most of all these calculation procedures lack physical-analytical descriptions of the procedure itself, presenting only the effects on important parameters such as the distance between seams in the roof or floor or gas pressure. Tschersich [Tschersich 961 developed an analytical model for an advanced calculation by analysing the degassing of seams in the roof and floor and the physical parameters of gasflow. This model might correct the lacks of existing procedures and improve the precision and reliability of additional calculations. The model simulates the emission record in seams of the roof and the floor. It takes into account not only a multitude of parameters such as the distance to adjacent seams and gas pressure but also the depth of seams, gas content, rank of carbonification, rock temperature, face advance rate, initial and succeeding mining and the face length. In order to comprehend and to verify those correlations we extended the model of Tschersich and programmed this enlarged model using the computer language C++. Aim of this research is to guarantee a much higher accuracy in calculating methane emission caused by mining. The improved planning is expected to result in more safety and better prevention of high methane con- tent in ventilation as well as in a better use of the capacity of the mining equipment. The application [Drijver, lnderst 961 of the ex- tended model will also be very useful in the course of research projects as it allows computer simulation, i.e. in-situ research can be extensively limited or even replaced.

Jan 1, 1997

By Lee A. Goetz

Cost control is a lot like motherhood - everyone proclaims its need and its worthiness, but is it really appreciated and used to successfully complete a project on time and within budget? Good Cost Control is a yardstick - requiring fixed definition but this does not mean rigidity for the project. It provides the means for telling: 1. Where you are going 2. When you will complete and 3. What it will finally cost. Cost Control does not fix the price of dreams nor the cost of projects loosely defined. It does not control costs in itself but provides the tools whereby engineering decisions can be made which will ultimately affect the project cost It does not even guarantee that a project will be completed within the original funds - but only, if this reflects management desires.

Jan 1, 1970

By R. A. Bergman, P. G. Thornhill

Development of the Falconbridge Ferronickel Process for treatment of lateritic nickel ores began with laboratory work in 1955, the year the Company commenced exploration of its concession in the Dominican Republic. Process development centred on selective reduction originally directed to producing calcines amenable to ammonia leaching, but later found suited to electric smelting. The reduction step of the process was developed in a 25 tpd shaft furnace pilot plant located in the Dominican Republic, to which was later added an electric melting furnace. After almost 3 years of development work on this scale the plant was expanded to 100 tpd for fixing design data for a commercial plant. This took the form of the 30,000 ton per year Nickel Ferro-nickel Complex of Falconbridge Dominicans, which started up in 1971.

Jan 1, 1979

By E. Spyridonos

Sustainable development in the mineral industry requires a paradigm shift from purely economic to multi-objective decision-making, considering economic, social, environmental and governance criteria. The commonly accepted aim is responsible stewardship of non-renewable resources. State-of-the-art 3D geological and mine modeling software technology can contribute to meet this objective as reliable and accurate geological models form the basis for an optimum management. The benefits obtained by the application of computerized modeling are illustrated at hand of three studies. The examples cover global and local producers of industrial minerals in fully developed as well as development countries. They refer to different levels of planning, from initial resource assessment over long-term planning to the generation of rolling forecast for operative planning in a running mine.

Jan 1, 2003

By Wan-Kyu Choi, Arpad E. Torma

The electrochemical reactions involved in a zinc sulfide flotation concentrate leaching with sulfuric acid in presence and absence of Thiobacillus ferrooxidans, as well as with ferric chloride - hydrochloric acid containing media, have been investigated. The cyclic voltammetric measurements revealed that many intermediate electrochemical reactions are involved in the zinc sulfide leaching. Using chronoamperometric and chronopotentiometric techniques, it was found that the leaching process is controlled by solid - state diffusion. The activation energy of solid - state diffusion process was determined by the Price's approach to be 21.3 kJ. The leaching mechanism is discussed in terms of solid - state properties (energy bondings) of the high energy gap solid zinc sulfide semiconductor and energy density states of redox systems of acidic leach media. A generalized model for the mechanism of zinc sulfide oxidation is present.

Jan 1, 1990

By J. A. Cooper, M. R. Petersen, P. O. Jackson, J. C. Langford

The organic, inorganic, and radiological characteristics of airborne aerosols have been measured as a function of particle size in controlled atmosphere test chambers and operating uranium mines. Concentrations of benzo(a)pyrene in two mines ranged from 26 to 57 ng/m3 of air. The carbon chain length of adsorbed n-alkanes was correlated with particle size. Normal mining activities produced an ore dust aerosol with mass median aerodynamic diameter (MMAD) greater than 2 µm. The elements Na, Al, Si, K, Ca, Ti, V, Fe, and U exhibited elemental ratios similar to bulk ore and had comparable MMAD's. The S, Zn, and Pb were higher in aerosols than bulk ore and were associated with smaller MMAD particulates. Radon daughter particle size distributions were influenced by the kinds of particulates

Jan 1, 1981

By Joyce A. Ober

Strontium occurs commonly in nature, averaging 0.034% of all igneous rock; however, only two minerals, celestite and strontianite, contain strontium in sufficient quantities to make its recovery practical, and these minerals are found in sedimentary rocks. Of the two, only celestite has been found to occur in deposits of sufficient size to make development of mining facilities currently attractive. Celestite, the most common strontium mineral, consists primarily of strontium sulfate (SrSO,). Strontianite, the second most common mineral, consists primarily of strontium carbonate (Sr CO3). Strontianite would be the more useful of the two common minerals because strontium is used most commonly in the carbonate form, but few deposits have been discovered that are suitable for development. The physical properties of strontium ores are listed in [Table 1].

Jan 1, 1994

By B. Ceccarelli

Many public domain programs useful in mining engineering, e.g., MULSIM, DZTAB, and EXPAREA, require tedious data input and generate pages and pages of printed output. To eliminate the tedium and to enhance the output, ETI U.S., Inc. developed GEM, Graphics for Engineering and Mining, a collection of application programs and underlying interface tools for VAX/VMS computers. This paper presents an example of how an application program in GEM enhances a specific public domain program. It describes how GEM provides automated graphics assisted input and output. The paper describes how this program uses the GEM User Interface: the 3D GKS device independent graphics, server and drivers, various mining, mathematical and statistical algorithms, the means of handling graphics, data including IGES, and the foreign language interface.

Jan 1, 1992

By S. C. Bandis, N. Barton

During drilling of deep boreholes, local mechanical failures of the wellbore walls may occur due to the inability of the incompetent overburden and reservoir rocks to withstand drilling-induced changes of the stress environment. At present, borehole failure mechanisms in three-dimensional stress fields are poorly understood. Our experimental investigations based on 3-D physical models demonstrate the stabilizing effect of the intermediate principal stress. The latter may play a dominant role in maintaining the integrity of the stress relieving failure zone around the borehole. However, this will depend on the stress anisotropy, the angle of hole deviation and on the angle of internal friction. Our tests also indicate that the failure zone can accomodate high extensional strains. Finally, relations between the physical models and closed-form elasto-plastic solutions are discussed.

Jan 1, 1986

By T. Tomioka

1. An Overall View of the Japanese Ferroalloys Industry 1) Depressed Demand for Ferroalloys: In Japan consumption of ferroalloys in the last ten years has decreased, although there has been some fluctuation from year to year. During this term production figures of the steel industry, which are closely related to consumption of ferroalloys, are as follows: Shipment of steel products for the domestic market has declined gradually from 69 million tons in 1979, which was the peak year for steel production, to 60.3 million tons in 1982 and 60.4 million tons in 1983, the level of 1978. In addition, exports also have been a downward trend since 1976, which was the peak year with tonnage of 34 million tons, to 28 million tons in 1982 and 31 million tons in 1983.

Jan 1, 1984

By C. R. Kuhn

From 1968 to 1975, most work in surface modification of inorganic materials involved silane coupling agents. A silane coupling agent can be described simply as an oganosilicon chemical having a general formula RSi-X3 wherein the R group is attached to a silicon in a thermally and hydrolytically stable manner, and X is a hydrolyzable group usually having an alkoxy functionality. About 1975, Kenrich Petrochemicals brought into the market place titanate coupling agents. Titanate coupling agents usually consist of one alkoxy group and three functional groups attached to a central titanium atom. Zircoaluminates became available in about 1982. Zircoaluminate organometallic coupling agents, which vary principally in their respective organofunctionalities, arise from a basic technology in which two different types of organic ligands are selectively bound to a low-molecular weight zircoaluminate backbone.

Jan 1, 1995

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents the preliminary test results obtained using a 0.38-kg/s (3,000-lb/hr) beta prototype MagMill. In processing Upper Freeport coal, the beta prototype recovered 82 % of the weight of the feed and 91 % of the heat content while reducing the potential emissions of sulfur by 61%. Pyritic sulfur in the MagMill product was reduced by 78% compared with that in the feed. For all runs, the mill product particle size was controlled to between 70% and 80% -741m (200 mesh). Recoveries of mercury, arsenic and selenium ranged from 35% to 45% of the amounts found in the feed. Power draw was reduced by 26%, and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2002

By Hassan El-Shall, Abbas A. Zaman, Brij M. Moudgil

The addition of organic and inorganic dispersants to aqueous suspensions of heterogeneous particles (kaolin) was found to significantly affect the solubility of metal ions from kaolin particles and stability of the dispersion. In most of the industrial applications of kaolin, highly concentrated slurries of controlled stability and fluidity are required. The solubility of kaolin particles in terms of aluminum and silicon ions and its effect on the stability of the slurry was investigated. The main objectives of this study were (1) to study the effect of the extracted metals on the properties and performance of the slurry, (2) to understand the reaction mechanism of dissolution of metals from kaolin, and (3) to understand the interaction mechanism of dispersants with kaolin particles. The controlling variables were dispersant dosage, slurry pH, solids loading, and aging.

Jan 1, 2003

By Robert Turner

Gold and silver processing techniques are some of the oldest in the mining industry. Gold mining of high grade veins and deposits has existed for centuries. However, only with the higher gold prices in recent years and heap leaching techniques have the low grade gold and silver deposits become feasible to mine and process economically. By mining and hauling 3,600,000 tons of ore per year at an average grade of 0.03 ounces/ton gold and 0.385 ounces/ton silver, the Zortman- Landusky operations became profitable in 1982. To maintain profitably, a stripping ratio of less than one ton of waste to one ton of ore, and mine run ore placed on the leach pads which will yield approximately seventy percent go1 d recovery.

Jan 1, 1984

By Joseph Cervik, Fred Garcia

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of the discharge pipe. These measurements are erroneous and tend to be high by as much as 30%. The Bureau of Mines determined correction factors (method factors) for anemometer measurements taken in this manner. Method factors for 10.2, 15.2, and 20.3 cm (4, 6, and 8 in) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By Deepak Gupta, Brij M. Moudgil

Attempts were made to improve the recovery of coarse phosphate particles by adding selected frothers or precoated fine particles. A number of frothers for floating, specifically coarse coal and metallic minerals, were examined. Two of the frothers increased the flotation recovery of coarse phosphate by 3% on bench scale. Plant evaluation yielded improvements in overall phosphate recovery in the presence of these frothers. Addition of fine particles was also found to enhance coarse flotation under given conditions. Size, amount, and hydrophobicity of the fines added was determined to have a major influence on the coarse flotation efficiency. The grade of the product with and without frothers and particulate additives remained the same. Change in froth stability and viscosity are believed to be the primary reasons for enhanced recovery of coarse phosphate particles.

Jan 1, 1989